Search Documents

By John D. Bardill

Data from extensive tests was obtained on friction-head losses of various sand slurries, composed of materials of different specific gravities and under varying transport conditions, to provide useful information for designing hydraulic transport systems. The tests were run in a pilot plant through 2-, 3-, and 4-inch lines with slurries composed of relatively pure barite and limestone solids. Available grinding and classification equipment did not permit attaining a comparable size distribution in the two materials tested, thus preventing direct correlation of friction-head loss values to physical properties or mineral composition. A total of 495 measurements were made of limestone slurries in the 2-, 3-, and 4-inch pipe test sections at flow velocities from 6 to 14 feet per second and pulp densities from 40 to 70 percent solids. A total of 640 measurements of barite slurries were made in the 3-and 4-inch pipe test sections at flow velocities between 7 and 14 f.p.s. and pulp densities ranging from 40 to 80 percent solids.

Jan 1, 1962

The purpose of the contract was to develop an improved coal mine dust sampler whose electrical-to-mechanical energy conversion efficiency would be superior to that of the presently available equipment. The electrical to (pressure) X (volume) conversion efficiency directly affects the size and weight of the air samplers. At least half of the mass of present equipment is composed of the rechargeable batteries. Any increase in efficiency will allow this mass to be reduced or the flow rote to be increased.

Jan 1, 1974

By Andrew Cecala

The Bureau of Mines performed tests to compare the effectiveness of steam and of water sprays to reduce respirable dust levels at mineral processing plants. By applying 0.22 wt pct water vapor as steam to product material, a 64-pct respirable dust reduction was recorded. By applying the same amount of moisture with water sprays, only a 25-pct dust reduction was recorded. By increasing the moisture content up to0.5 pct using water sprays, the dust reduction was increased to 55 pet, which was still less than the dust reduction achieved by adding less than half that amount of water in the form of steam.

Jan 1, 1985

By Julius Roth

Flyrock is the source of most of the injuries and property damage in a majority of blasting accidents in surface mines. A quantitative correlation between shot conditions and maximum flyrock range can be used to define a "blasting area" in which no personnel or equipment should be present during a shot. The approach used was to develop a model that correlates shot conditions and initial flyrock velocities and permits computation of flyrock range from ballistic trajectories. The Gurney formula for velocity of explosively-propelled plates or fragments was adapted to explosively-propelled flyrock from vertical rock faces or from bench tops. The modified Gurney formula was then "calibrated" with measured flyrock velocities from mining and explosives literature. Charts were then developed for possible field use which give maximum flyrock range as function of shot conditions. The model indicates that for flyrock from vertical faces, borehole diameter, minimum burden and height of explosive column define maximum flyrock range for a given explosive, shot in a given rock. For flyrock originating from bench tops, flyrock range appears to be controlled by the distance of the top of the explosive column to the borehole collar, by total explosive load per borehole and, to a lesser extent, by borehole diameter.

Jan 1, 1979

By Ronald P. Hollenbeck

The value of mineral production in Alabama reached a new high of more than $246 million. 4 percent above the previous record established in 1964. New high values were reported for bentonite, portland cement, fire day, kaolin, miscellaneous clay, lime, crushed limestone, crushed marble, mica. salt, and sand and gravel. Among the States, Alabama ranked second in the production of bauxite and scrap mica and third in the production of native asphalt. The mineral industry of Alabama was dominated by the mining and processing of coal and Slone, the manufacturing of cement, and the production of crude petroleum, which together comprised 85 percent of the total value of mineral output, compared with 84 percent in 1964. The iron ore industry continued to decline. Coal production continued to increase, resulting in the State's coal-mining best year since 1948.

Jan 1, 1967

By Bryan Buchholz, N. Kumar Kittusamy

Previous studies indicate that operators of heavy construction equipment are afflicted by musculoskeletal injuries of the arms, shoulders, neck, and lower back. These injuries appear to be due to excessive periods of sitting (static posture), work intensity, whole-body vibration, high resistance levers, repetitive motions, and awkward postures. (2-5) Although numerous studies have shown an association between operation of heavy construction equipment and symptoms of musculoskeletal disorders, very little research has been performed that systematically characterizes operating engineers' exposure to ergonomic hazards. The objective of this study was to systematically characterize the ergonomic hazards associated with excavating operations. As such, the following were performed: (1) vibrations were measured at the operator/seat interface (X, Y, and Z axes), and at the floor of the cab (Z axis); (2) psychophysical ratings of whole-body vibration (WBV) level and overall seat design were obtained; and (3) postural assessments of the job were made. Methodology This study evaluated an inexperienced female operator performing excavation, utilizing two different pieces of equipment. The operator was 37 years old, 162 cm tall, and weighed 80 kg. She had approximately 15 hours of operation time (experience) on the equipment evaluated. The two pieces of equipment used were: a Case Super 580E (1986) backhoe/loader, and an Insley H-2000 excavator (1975) (see Figures 1 and 2). More evaluations were performed on the backhoe/loader than on the excavator. The following evaluations were performed on the Case equipment: 1) vibration levels at the seat and floor; 2) psychophysical ratings of the overall seat design and vibration levels (for the task duration, and for an 8 hour duration); and 3) postural assessments. For the Insley equipment, all of the evaluations were performed except vibration measurements. When the evaluations were conducted, the following environmental conditions were noted: the temperature was 31°F, and soil and terrain conditions were rough and frozen.

By Jerry J. Gray

Transportation charges for mineral commodity movements in western Oregon and western Washington were determined mainly by a stratified random sample canvass of producers. Total 1965 mineral production value for this area was $53.3 million; the cost or charge to move this production from the mine to the consumer or to the point of consumption was determined to be an additional $38.7 million. Thirty seven companies were contacted as a sample out of a total population of 349; the statistically expanded sample production value deviated 3.6 percent from that obtained by the Bureau's annual canvass. The agreement between the sample results and the canvass totals demonstrated the effectiveness of the sampling method for obtaining data with a predesigned level of accuracy. For comparison, the north-central Idaho and western Montana area was studied, A random sample experiment was designed, but because of the dominance of a few major companies, a random sample technique would have required more visits to producers than if only the larger firms were contacted. Eighty-four percent of the 1966 mineral value ($198.6 million) was accounted for by interviewing 27 firms out of a total population of 199. Total transportation costs or charges for the area were $26.7 million. The significant difference observed between the relationship of minerals production value and transport charges between the two areas investigated can be attributed to the difference in the minerals produced. The western Oregon and western Washington region is a nonmetals-producing area as opposed to the predominance of metals production in the Idaho-Montana region.

Jan 1, 1968

By Winton Gale, David Oyler, Jinsheng Chen, Christopher Mark

The National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia have collaborated to conduct an extensive study of roof bolt strata interaction at the Emerald mine in Southwestern Pennsylvania. The primary goal of the project was to obtain detailed data on the interaction between the mine roof and the support elements for use in modeling studies. The study site was a longwall tailgate subjected to high horizontal stress. Three arrays of instruments were installed at the site, one in the tailgate entry and two in an adjacent crosscut. Pumpable concrete cribs were present in the tailgate array, and cable bolts were installed in one of the crosscut arrays. The instruments included mechanical and sonic extensometers for measuring roof movement, instrumented roof bolts, and three-dimensional roof stress cells. The study was ultimately successful in determining the magnitude of the horizontal stress concentration, the height of roof failure and the roof failure sequence, and the loading history of the primary roof supports.

By Sean Gallagher, Thomas G. Bobick, William S. Marras

Twelve healthy, experienced underground cool miners performed lifting capacity tests in stooped and kneeling postures using a modified psychophysical procedure. Subjects adjusted weight in a lifting box to the maximum they could handle without undue fatigue in an asymmetric lifting task. Lifting periods were 20 min in duration and the frequency was 10 lifts/min. Tests were performed under a 48-in. roof that restricted the subject&apos;s posture. Psychophysical. physiological, and biomechanical dependent measures included the maximum acceptable weight of lift (MAWL), heart rate (HR), rate of oxygen consumption (VO2), ventilation volume rate (VF), respiratory exchange ratio (R), and integrated electromyography (EMG) of eight trunk muscles. Results indicated that the MAWL was significantly lower when kneeling than when stooped (p < 0.05), Furthermore, metabolic demands were greater in terms of HR (p < 0.005) mid VO2 (p < 0.05) when kneeling. Left and tight erectores spinae muscles exhibited increased EMG activity- in the kneeling posture (p < 0.001). It was concluded that psychophysical lifting capacity is decreased, while the metabolic stress and internal load on the spine are increased, in the kneeling posture. Results of this Bureau of Mines study indicate that it may be advisable to reduce the weight of materials that are handled repetitively in the kneeling posture.

By Nathan Feldstein

The wetting of coal dust by aqueous solutions of surface active agents (surfactants) has been studied. Selected for study were thirty coals and typical surfactants selected from the typical classes of anionic, non ionic and cationics. Of these three classes the practical use of cationics in aqueous solutions has been eliminated due to the inherent negative Zeta potential charge of the representative coals studied. The wetting of the coals has been examined by column flow, contact angle, and settling rate measurements. Results indicated that both anionic and nonionic surfactants are to be considered viable for use; low critical micelle concentration values are also preferred for the surfactants. Study of native waters showed substantial variation in properties, i.e., pH, calcium ion concentration, and conductance. pH variations were also noted to affect the effectiveness of selected surfactants. Combinations of nonionic and anionic surfactants have, in certain instances, produced synergistic enhancement in the coal wetting superior to the effectiveness of each surfactant alone.

Jan 1, 1981

By F. S. Karn

Conditions necessary to obtain optimum yield of useful products when coal is rapidly heated to extreme temperatures by laser irradiation were determined by the Bureau of Mines. Product distribution and yield were investigated as functions of several variables. Low-rank coals with high-volatile matter gave highest total gas yields. Medium-rank coals gave the highest yields of H2 and CA and low-rank coals gave highest yields of CO and C02. Macerals gave gases of approximately the same composition, but the total gas yield increased in the order fusinite, micrinite, vitrinite, and exinite. Total gas and C2H2 yields varied inversely with particle size. The addition of nominally inert gases such as Ar, He, N2 increased yields of H2, C2H2, and total gas. Metals such as nickel and platinum had little influence on the rate of coal decomposition. Total gas yield increased with total energy of irradiation, and the ratio of C2H2-CH4 increased with concentration of energy. A study was also made of the irradiation temperature, and a material balance was calculated.

Jan 1, 1970

By Walter W. Kaufman

This report summarizes a study conducted to establish the nature and impact of regulations governing disposal of refuse from underground coal mines. The regulations affecting refuse disposal in eight major coal producing states are collected, summarized and reviewed. Federal regulations applicable to refuse generated by underground coal mines are also included. Common refuse disposal practices are discussed as are the refuse quantities generated annually in each study state. Technical requirements of regulations are discussed acid presented in appended tables. Economic implications are also assessed through cost analyses of three major types of disposal processes. The report also includes an assessment of future trends in regulation and refuse generation plus a series of recommendations concerning potential improvements in both the regulatory and refuse disposal processes.

Jan 1, 1978

By Don M. Coulter

"INTRODUCTION Bauxite, in Appalachian Alabama, occurs in the Rock Run and Goshen Valley districts in Cherokee County; in Nences Creek Valley near Jacksonville; near Anniston in Calhoun County; north of Fort Payne in DeKalb County; near Ashville in St. Clair County; and near Talladega in Talladega County.In February 1942, Preston E. Cloud, Jr., assistant geologist, Federal Geological Survey, began a study of these bauxite deposits and the geology relating thereto.The Bureau of Mines established field headquarters at Piedmont, Calhoun County, in July 1942. Mineral agreements covering a total of 11,097 acres were executed with 15 landowners in the Rock Run district; 38 in the Goshen Valley district, covering 7,575.5 acres; and 3 in the Nances Creek Valley district, covering 988.5 acres. Drilling was done on the properties of 9 land¬owners in the Rock Run district, and on the property of 1 landowner each in the Goshen Valley and the Nances Creek districts. Drilling began October 26, 1942, and ceased on May 17, 1943.Power drilling was supplemented by a labor crew that drilled hand-auger holes in shallow deposits and sampled .old shafts, mines, and mine dumps.In all, 222 holes for a total of 13,250 feet were drilled. Of these holes, 88 penetrated bauxite but too low in grade to constitute ore."

Mar 1, 1948

By Michael J. Jorgensen, Anoop Polsani, Khurram S. Khan

Riveting operations in aircraft manufacturing involves the use of power tools for manually drilling holes for the rivets, power drills for the setting of the holes for the rivets, as well as rivet guns to drive and set the rivets. To close the rivet, the rivet is driven against a metallic bar commonly called a “bucking bar”. The bucking bars are typically held firmly to increase the quality of the riveting, as well as keep the bucking bar from “dancing” against the metal piece being riveted. Thus, employees in aircraft manufacturing involved in riveting are exposed to hand-arm vibration from several sources, and epidemiological evidence suggests that vibration-related musculoskeletal disorders are associated with long term exposure to riveting tasks in the aircraft manufacturing of aircraft.1,2 Recently, tungsten technology has been introduced into aircraft manufacturing for bucking bars, which are heavier than traditional steel bucking bars of the same size. Rivet guns with tungsten pistons instead of steel pistons have also recently been introduced with the objective of reducing vibration exposure to the riveter. The objective of this study was to assess vibration characteristics of steel and tungsten bucking bars and rivet guns to identify the combination that simultaneously reduced the combined exposure to both the “riveter” and “bucker”. Methods Vibration (10g tri-axial accelerometer, Biometrics S2-10G-MF Series 2) was measured from eight experienced employees using seven different rivet guns on size 6 rivets, with the same person bucking for all subjects. Vibration was also measured on two different bucking bars for these same eight subjects, with the same person driving the rivets using the various rivet guns. The rivet guns consisted of three E4 steel piston guns with different RPMs (Guns A-E4, B-E4, C-E4), an E4 vibration dampened rivet gun (Gun D-E4D), an E3 steel piston rivet gun (Gun E-E3) and an E3 and E4 tungsten piston rivet guns (Guns F-E3T and G-E4T). The bucking bars were made of 90% tungsten (1694g) and cold-rolled steel (843g), and were the same shape and size. A two-way repeated measures analysis of variance was performed on the vibration (mean frequency weighted resultant acceleration) on both the rivet gun side and the bucking bar side, and mean rankings were used to assess the vibration simultaneously for the rivet gun and bucking bars to investigate which combinations provided the lowest vibration exposure. Results Frequency weighted resultant acceleration was significantly lower on the E3 tungsten (F-E3T) rivet gun than the E4 steel piston (B-E4) and the E4 tungsten piston (G-E4T) rivet guns (Figure 1). When measuring vibration on the bucking bar, the E4 (A-E4) steel piston rivet gun resulted in lower vibration on the bucking bars than the E4 tungsten piston (G-E4T) and E4 vibration dampened (D-E4D) rivet guns (Figure 2). Additionally, use of tungsten bucking bars resulted in a 35% decrease in resultant frequency weighted acceleration than when using steel bucking bars.

Jan 6, 2006

By Roger M. Turpening

This study was performed to examine the feasibility of using seismic shear waves to detect the presence of abandoned coal mines. !he Antiquity Coal Mine near Antiquity, Ohio was used as a region of known voids. No attempt was made here to accurately locate the mine tunnels if detection was obtained. The results of this study were positive. Sharp changes in the amplitude of the received shear waves were clear indications of the presence of a fluid (gas or liquid) filled region between the source and receivers. When moving the source showed no change in the received signals it was concluded that the voids existed beneath the sensors. Prior to these tests drilling (SM-3) had determined that a void did exist in this area. This void was confirmed by this shear wave test and two additional voids were found.

Jan 1, 2012

By Mary F. Koehler

Continuing a program of thermochemical investigation of compounds of to ferroalloy elements, this paper contains ins values of the heats of formation of two sodium molybdates (Na2Mo04 and Na2Mo207) and three sodium tungstates (NO2W4, Na2W207, and NA2W207, and Na2W4013). The experimental method was solution calorimetry. The solution medium was sodium hydroxide solution, except that hydrofluoric acid solution was used for sodium tetratungstate. The heat of formation values are given with reference both to the constit¬uent elements and to the constituent oxides. These data are of prime impor¬tance in the thermodynamic consideration of these substances, as their accumulation includes the most difficult and time-consuming steps toward evaluating the free energies of formation and thus the potential reactivities and thermal stabilities. Except for values for sodium monomolybdate and monotungstate, no previous similar data were contained in literature sources.

Jan 1, 1962

By Paul C. Hyndman

Three properties in the Tuolumne River RARE II area, the Eagle Bluff Mine (lode) and the Indian Creek Bar and Bossy Bar Prospects (placer), have identified subeconomic gold resources (table 1). Nineteen other properties have potential for gold resources. Adjacent to the study area, five properties have identified mineral resources, and nine others have potential for resources. Properties having high-grade zones (shoots), but licking enough tonnage to be classified as resources, are listed in table 2. Gold, in lode and placer deposits, is the principal mineral commodity in the Toluene River study area. Ten properties within the RARE II boundary have gold-rich zones or shoots; they range in size from 12 to 2,500 tons and in average grade from 0.09 to 0.97 oz gold per ton.

Jan 1, 1983

By Ren G. Dong, Thomas W. McDowell, John Z. Wu, Chris Warren, Dan E. Welcome, Chun L. Dong

Hand forces are important factors for risk assessment of hand-arm vibration syndrome (HAVS).1 Grip force is one of the most important force components in the operation of powered hand tools. A considerable number of studies on grip force have been reported. It is well known that the grip force applied on a cylindrical handle is not uniformly distributed on each axis across the center of the handle cross-section.2 Therefore, maximum and minimum orientations of grip force exist around the handle. Such orientations have not been clearly identified. In a recently proposed international standard (ISO/CD 15230, 2005),3 it is stated that “the direction of the main gripping force is generally parallel to the z-axis defined in ISO 8727.” 4 This assertion is questionable, and further examinations are required. The objective of this study was to establish a fundamental theory on the distribution of the grip force around cylindrical handles. Methods As shown in Fig. 1, the grip force is defined as a vector composed of normal and shear components (FN & FT) in this study. Fig. 2 shows the hand coordinate system defined in this study, together with the ISO systems.1,4 Based on this novel grip force definition, we derived four fundamental properties and a theorem. More significantly, we formulated a novel hypothesis: similar to Mohr’s circle of stress, the normal and shear components can be represented approximately using an ellipse on the plane of the two force coordinates, as shown in Fig. 3. The maximum and minimum grip normal forces are termed as the first principal grip force (F1) and the second principal grip normal force (F2), respectively. Their corresponding orientations are termed as the first principal grip angle (a1) and the second principal grip angle (a2). A series of experiments were conducted to test this hypothesis. Twelve

Jan 6, 2006

To improve the ventilation of large-opening under-ground stone mines by using stoppings made from stone left in place. Background Underground stone mines typically use large room-and-pillar openings with little ventilation control. Stone miners may be exposed to contaminants that include silica dust, diesel particulate matter (DPM), exhaust gases, nuisance dust, and face shot (blasting) fume gases. The health risks from breathing these fine particles and toxic organic materials are well documented. Although contaminants such as dust or diesel exhaust can be some-what controlled at the source, the escaping contaminants are often diluted and removed from work areas using ventilation with minimal controls. In many cases, current mine ventilation practices use trial-and-error techniques to improve ventilation. The growing realization of the importance of a healthy work environment along with increased regulations will require many stone mines to implement new ways to improve ventilation. In-place stone stoppings are one option. Mine air flows from one point to another because of a pressure differential between those points. This pressure differential is established using a mechanical fan in conjunction with separations (stoppings) between high-pressure (intake) and low-pressure (return) airways. The separation of intakes and returns is an important concept that is used in most other types of mines. Normally, air moves through underground stone mines with minimal control technology. Fans are placed in locations where they are thought to be most beneficial, and intakes are not separated from returns. In a few smaller underground stone mines, proper ventilation can be achieved with a few strategically placed fans. However, as these mines increase in size, moving adequate quantities of air through-out the mine becomes harder, and separation of intakes and returns becomes a problem. Building traditional mine stoppings to separate the intake and return airways in entries with a cross-section area often exceeding 800 ft2 is difficult. The stoppings must be able to withstand both the dynamic pressure from face shots and the static pressures created by the fans. Construction and maintenance difficulties, as well as high costs, are the main factors preventing these traditional mine stoppings from gaining wide acceptance by the stone mining industry.

Dec 1, 2002

By Stephen C. Tadolini, Thomas M. Barczak, Paul McKelvey

A new generation of hydraulic mine support prestressing devices has been developed. These thin-walled steel shells are machine-welded and can be inflated with water or any liquid to provide prestressing for a wide variety of roof support products ranging from Can supports to props and cable bolts. With an expansion capability of several inches, depending on the geometry and size of the unit, they can also establish roof contact eliminating the need for wooden wedges or crib blocks that are commonly employed with several standing roof support products. Capable of withstanding pressures from 1,000 to 6,000 psi, these cells are able to transfer roof loading into the support structure without rupturing. A recent development has been the addition of an inexpensive yield valve that provides control of the maximum pressure and load development on the support. This paper examines the performance capabilities of these inflatable prestressing units and the impact they have on the performance of various support systems, including an evaluation of the overall stiffness of the support system and the load control during yielding of the prestressing unit. Recommendations are made regarding the design requirements of the prestressing unit to optimize the support performance. A summary of mine applications using this technology is provided with general comments regarding their impact on ground control.