Search Documents

By N. Seidle

Numerous studies conducted in the 1960's and 1970's concluded or implied (1) that a high accident rate in terms of severity and frequency exists among new (first year) operators of mine machinery equipment, and (2) that lack of experience and training is a major cause of this high accident rate. Further studies refined this premise to show that the major causes of accidents among first year operators are: (1) lack of manipulative skills; (2) failure to follow/adhere to routine procedures; and (3) failure to recognize and respond properly to hazards. This report describes the design, development, and manufacture of a shuttle car operator training system, including a program of instruction which: ? Is economically feasible. ? Addresses accident data and specific causes of accidents. ? Includes an aerospace quality simulator of sufficient fidelity to teach and develop manipulative skills, recognition of and response to hazards, and routine and emergency procedures. ? Is designed to significantly reduce the severity and frequency of accidents especially during the operator's first year. ? Is designed to significantly improve the performance of the trainee as compared to the standard learning curve. Development of the simulator produced several valuable by-products including a major state-of-the-art technological advance in visual systems for simulators, and a first-time application of (certain) advanced filming techniques to underground filming.

Jan 1, 1984

By G. W. Birge

Carbonizing properties of the principal coal beds of Perry County, Ky., are described in this Bureau of Mines report. Seven samples, representing the Hindman, Flag, Haddix, and Fire Clay beds, were carbonized by the Bureau of Mines-American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Carbonizing properties of blends of Flag and Fire Clay coals, with 20 and 30 percent Pocahontas No. 3 low-volatile coal from McDowell County, W. Va., also were determined. Expanding properties of the Flag and Fire Clay coals and their blends were determined in the Bureau of Mines sole-heated oven. The Perry County coals tested are high-volatile A bituminous in rank and, with the exception of the Hindman-bed sample, which contained excessive sulfur, were chemically suitable for metallurgical use. The three coals tested in the sole-heated oven contracted less than normal for Appalachian coals of similar rank, Blending the Fire Clay and Flag coals with 20 or 30 percent low-volatile coal increased coke strength appreciably but increased the expansion beyond normal limits for industrial blends.

Jan 1, 1962

By Robert L. de Beauchamp

The Bureau of Mines designed a chlorination apparatus to prepare CrCl2 free of CrCl3 by the direct reaction of chlorine and chromium. Equipment and procedures were developed for routine preparation of 25-pound batch quantities of anhydrous CrCl2. Calcium, iron, nickel, and silicon impurities were in the 0.01 to 0.05 percent range, and all other impurities were below 0.01 percent.

Jan 1, 1968

By Carl Sunderman, Steve Signer

Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed several new tools for evaluating roof support performance. A miniature data acquisition system (MIDAS) was developed that can collect readings from up to 16 strain gauges at regular time intervals and store the readings for later retrieval. Three LED lights change from green to yellow, then red, based on the reading levels and/or rates of change of rock movement. This feature can be used to warn miners of rock instabilities. The system can be used with any strain-gauged support (resin bolt, friction bolt, cable bolt) or with a newly developed rock strain strip (ROSS) developed by NIOSH to measure rock strain. A ROSS is grouted in a hole drilled adjacent to the rock support to be evaluated; the deformed shape of the ROSS provides anchorage on either side of the strain gauges. Data from both laboratory tests and field evaluations are presented that describe the capabilities of both the MIDAS and ROSS instruments.

By T. R. Achenbach

1. This, the final report to the U. S. Bureau of Mines on the program with the subject title, presents the data obtained from June 29, 1973, to April 20, 1974. 2. Operating in the Illinois #6 coal seam, the effectiveness of foam opposed to water was compared in reducing respirable coal dust. A combination of 39 foam generators and 14 water sprays were used during the foam tests. Sixty one water sprays were operated during the water tests. Data from 24 shifts using foam and 21 shifts using water are presented. 3. Additional work on foam generator design should be undertaken to provide coverage to a wider area with foam. 4. The general attitude of those working on the foam program and with the miner at the face was positive. It is urged that the work be continued. 5. The minor respiratory irritations evidently caused by an aerosol effect of the surfactant should be investigated. 6. The statistical analysis of the tests will be made and reported by the U. S. Bureau of Mines.

Jan 1, 1974

Objective To develop safety training tools for mine safety and health trainers that can be used for both new-miner training and annual refresher training. Background For the past 3 years, NIOSH has been developing training materials for mine safety trainers in response to gaps identified during stakeholder meetings. Most materials have been directed to the hazards of underground mines, but the recent passage of Part 46 of CFR 30 required new-miner and annual refresher training in aggregate operations. One result was the identification of another audience needing basic information about safety in mining. Trainers characterized trainees in this segment of the industry primarily as young males, many of whom had little work experience. Approach Training specialists from the Arizona State Mine Inspector’s Office approached NIOSH researchers early in2002 about the possibility of a collaborative project to develop safety training materials for new trainees in aggregate operations. A preliminary search of MSHA accident statistics identified over a dozen common hazards that could be targeted in a training video. A storyline was developed for review by safety specialists in the aggregate industry, and a script was written to cover the selected hazards. Although the target audience was primarily new hires, the finished video was also to be relevant to more experienced workers.

Jan 1, 2003

By Kenneth H. Johnston

This report describes in detail three waterflooding projects and a pressure-maintenance project in Butler and Cowley Counties, Kans., that will be visited on the 1963 annual spring tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the flooding of five oil-producing horizons separately with injection water furnished by two water-treating plants. Discussion of the individual projects includes information on their early history, the source and treatment of the injection fluids, oil production decline curves, and the results of water injection on oil production.

Jan 1, 1963

By Galen G. Waddell

The Deep Creek zinc and lead mine afforded an excellent example of a relatively small underground mine operation that approached the low mining costs of large, highly mechanized mines, An open stope mining method incorporating sublevel benches and vertical long holes was used (fig. 1). Detailed descriptions are given on the exploration program, stope development, stoping procedures, and pillar removal. Pressure grouting was used to check the inflow of water and thus prolong the life of the mine. Statistics on mining costs and on electric power consumption, haulage from mine to mill, and milling costs are included.

Jan 1, 1963

By Paul M. Tyler

Magnesite is of importance primarily as a refractory material for lining steel furnaces , although substantial amounts are used in the production of flooring compositions and other building materials and for certain chemicals , notably epsom salts . Since consumption for all of these purposes is largely in the eastern United States and domestic deposits are situated in California and Washington , this country's magnesite mining industry , which was created largely by war- time conditions , has subsequently been sustained by tariff protection .

May 1, 1931

By Jack Touseull

On November 15, 1972, the Bautsch mine, a lead-zinc mine in Paleozoic dolomites, experienced a massive rock failure involving 3 to 5 million tons. Because this failure was large and extended to the surface, it was included in the Federal Bureau of Mines investigations on "Massive Rock Failures." Analysis of the rock mechanics and mode of failure revealed that failure at the Bautsch mine was the result of the interrelationship of many factors. Factors related to the failure were found to be external and internal to the mining environment. Unlike internal factors, external factors were not apparent and, therefore, many external factors were investigated; some of which are not normally considered in rock mechanics analyses. External and internal factors determined to be of significant importance were: (1) precipitation, (2) fractures, (3) plastic clay layer, (4) topography, (5) rock alteration, (6) bedding, and (7) mining zone dimensions. Because of the conditions at the mine, failure could have been predicted without extensive instrumentation. Application of basic geologic and engineering principles to the internal and external factors could have predicted failure. Alternately, failure would, in all probability, have been delayed by years if, after 1962, mining had been curtailed in the area of failure.

Jan 1, 1980

By Kenneth O. Bayard, John D. Sullivan

"This repot continues the series of papers being prepared at the Southwest Experiment Station of the Bureau of Mines in cooperation with the department of mining and metallurgy, University of Arizona, on factors involved in the leaching of ores. A list of previous publications is given in the bibliography at the end of this paper.Four factors are essential to the leaching of any copper-bearing ore: (1) A solution that will attack the copper minerals must get into the body of the ore particles; (2) the copper minerals must be dissolved by the solution; (3) the solution containing the dissolved copper must find its way out of the voids of the rocks into the main solution; and (4) the copper in solution must be recovered by some means of precipitation.This paper considers the third step -- the extraction of the water-soluble copper. From leached ores. The usual commercial practice in leaching copper ores consists of: (1) Crushing the ore to pass through a screen with approximately one-quarter or one-third inch openings; (2) charging the crushed ore into a fat; (3) adding, usually by upward percolation, a solution that will attack the copper minerals; and (4) washing the copper-laden solutions out of the ore with solutions weaker in copper than the pregnant solution, and finally with water. A countercurrent system of leaching and washing is usually employed. In some plants the solutions are circulated during leaching and washing, and in others they are not. In some plants the wash solutions are added by upward percolation, while at Chuquicamata the so-called ""piston-displacement"" method of washing is employed.The following condensed resume of the leaching cycle of the plant of the Inspiration Consolidated Copper Co. is given to present to the reader a picture of the steps involved in a typical leaching cycle. This plant was recently described in detail.4 The ore, crushed to pass openings 11/2 inches in diameter, passes over a screen with ¼-inch openings. The undersize from the screen goes to a Dorr howl classifier that removes the primary slime from the circuit. The overflow from the classifier is treated in a slime-leaching plant. The oversize of the ¼-inch screen passes through rolls, where it is crushed to pass a 3/8-inchscreen. The undersize from the 3/8-inch screen join with the coarse material from the classifier, and the combined products become the feed to the leaching vats. There are 13 concrete lead-lined leaching vats. The complete leaching cycle is 13 days. Eight tanks are under acid-iron content at all times; three are being washed, one tank is being filled, and the one is being excavated. The electrolyzed solution from the tank house, to which amount of new acid has been added, is put on the oldest tank of ore under need This solution travels from tank to tank and finally emerges from the newest ore"

Apr 1, 1931

By John H. Soulé

This paper describes the location and general features of the ?Red Bed? or sandstone copper deposits in southeastern Colorado and New Mexico. Most of the areas containing this type of deposit were visited, and many deposits were examined. Some deposits were not visited because of lack of information as to their location. In the large area covered a great variety of climatic, geographic, and topographic conditions exists. Some of the deposits are in arid areas, whereas others are in heavily forested regions. Altitudes range from 3,400 to 9,200 feet, and the terrain varies from flat plains to rugged mountains. Transportation is a difficult problem in most of the districts, involving long truck hauls to a railroad and long rail hauls to a smelter.

Jan 1, 1956

By Jerome Apt

This report presents the methods and results performed pursuant to the U. S. Bureau of Mines contract entitled "Noise Abatement in Mining Machinery," Number H0122054. 2.1 Background Until the Congress of the United States created and passed Public Law 91-173, the Federal Coal Mine Health and Safety Act of 1969, there were no directly-applicable standards for noise exposure for underground coal miners.1 Section 206 of this law, approved December 30, 1969, provided for standards of noise to be applicable to each coal mine. It is as follows:

Jan 1, 1975

By Duane L. Abata

Toxic gases produced by the detonation of six explosives were measured in an underground hardrock metal mine during actual mining operations. The six explosives included two semi-gelatin dynamites, three slurry explosives and an ammonium-nitrate, fuel-oil/ammonia dynamite combination. Explosives were detonated at the face of a drift and the toxic gases produced by the detonation were trapped to the end of the drift by a bulkhead located a short distance away from the face. Toxic gas concentrations were then measured with direct readout instruments and together with the containment volume, the toxic gas volumes per mass of explosive were calculated. Toxic gas measurements were found in the following ranges (ft3/lbm): N02 0.010-0.035; N02, 0.003-0.019; CO, 0.08-0.30; S02, 0.00-0.05; and C02, 0.7-1.8. Results showed that toxic gas production (ft3/lbm) correlated with the densities (kg/m3) and energy densities (kJ/kg) of the explosives tested.

Jan 1, 1978

By Gabriel Esterhuizen, Tom Goodwin, Scott Schilling, Anthony T. Iannacchione

The Roof Fall Risk Index (RFRI) is a new method introduced by the National Institute for Occupational Safety and Health (NIOSH) to assist the underground stone mine operator in 1) assessing defects the mine strata and 2) rating the relative roof fall risk these defects pose. The RFRI utilizes observational techniques to identify defects in the roof strata caused by local geologic, stress, and mining conditions. Assessment values for ten defined defect categories provides the foundation for estimating a range of risk conditions between 0 and 100 that define the potential for a roof fall. This paper examines how the defect information is collected using two field verification sites and proposes methods to analyze the RFRI data. These examples provide information on how well the method replicates observed conditions and how it might be applied in practice.

By Joseph D. Davis

Selection of a suitable coal or coals for the manufacture of coke of desired quality with due consideration of the purpose for which the coke is intended requires careful thought, and often it will pay to go to considerable expense in testing such coals as may be available. In general it will

Jan 1, 1942

By F. R. Lee

When the Bureau of Mines was established in July 1910, one of the problems immediately attacked by the new organization was the development of standard, for the design and testing of electrical equipment that could be used without fear of initiating fires and explosions in underground coal mines. Research and investigation by Bureau personnel, supplemented by the published results of similar work by European mining authorities, led to the establishment of standards or "schedules." which guide manufacturers ill the design of many types of electrically operated machines and devices used in underground coal Mining. By issuing these standards, Bureau personnel establish the requirements to be met by such equipment before it tan be approved by the Bureau of Mines as permissible for use in gassy coal mines. Every 2 years the Bureau of Mines publishes a list of equipment that leas been accepted as approved or permissible during the preceding 2 calendar years. This is done to inform the mining industry of the availability y of the latest equip¬ment for safe use underground.

Jan 1, 1964

By J. D. Dixon

This Bureau of Mines report describes a technique for determining the confining pressures that must be provided for stabilizing underground openings in incompetent rock. The technique is adapted for use with a nonlinear finite-element computer code, NONSAP, to obtain stabilization pressures for linear or nonlinear stress distributions in the rock media around the excavation. This analysis permits a point-wise calculation of active rock pressures that depend on the values of shear stress and strength along the excavation surface. The approach is applied to the solution of several sample problems. The results show that both the magnitude and the distribution of stabilizing confining pressures are significantly influenced by rock and joint strengths, joint orientation, and biaxial nature of the load field.

Jan 1, 1976

By F. R. Lee

[WHEN the Bureau of Mines was established in July 1910, one of the problems immediately attacked by the new organization was the development of standard, for the design and testing of electrical equipment that could be used without fear of initiating fires and explosions in underground coal mules. Research and investigation by Bureau personnel, supplemented by the published results of similar work by European mining authorities, led to the establishment of standards or "schedules." which guide manufacturers in the design of many types of electrically operated machines and devices used in. underground coal Mining. By issuing these standards, Bureau personnel establish the requirements to be met by such equipment before it tan be approved by the Bureau of Mines as permissible for use in gassy coal mines. Every 2 years the Bureau of Mines publishes a list of equipment that leas been accepted as approved or permissible during the preceding 2 calendar years. This is done to inform the mining industry of the availability of the latest equipment for safe use underground.]

Jan 1, 1964

Phase I of U.S. Bureau of Mines contract H01220S3, "Improved Sensors and Fire Control Systems for Mining Equipment, II was an investigative effort involving study of the fire problem and preliminary design of a fire protection system. Overall contract objectives included three basic efforts: * Identify problems * Develop a design * Demonstrate a system The first two efforts were conducted during the period June through November, 1972. Phase II will involve testing of system components; construction and testing of a mockup; and demonstration of the system on a truck to prove its effectiveness under actual operational and environmental conditions.

Jan 1, 1972