Search Documents

"Wet low intensity magnetic separation has been used for the recovery of magnetite for decades. As high-grade reserves continue to decline, low grade magnetite ores are being targeted for iron production. Low grade magnetite mineralisation is typically fine grained and requires fine to ultrafine grinding (P80 40 - 30 µm) to liberate it from, predominantly, silica/silicate gangue matrices. Grinding to such particle sizes requires high power consumption and produces excessive fines which impact negatively on wet magnetic separation and tailings dewatering. In addition, the dearth of fresh water for mineral processing in arid areas impacts negatively on the economic viability of low grade magnetite projects. These challenges have motivated innovation in dry magnetic separation technologies for the beneficiation of magnetite that can be economically applied on a large-scale. Such technology has been developed in the Cyclomag Planar magnetic separator (PMS) invented by South Australia-based Christopher Kelsey of IMPTEC P/L. The significant gangue mineralisation associated with magnetite ores in South Australia is quartz. In this study, the performance of the Cyclomag PMS on the recovery of magnetite mineral from magnetite-quartz blends was investigated. Magnetite-quartz blend were subjected to the PMS at varying control parameters - magnet discs rotation speed, inlet airflow and feeder speed. The study showed a successful dry separation of magnetic mineral from non-magnetics using the Cyclomag PMS. The PMS has potential to effectively recover magnetite mineral."

Jan 1, 2018

By K. W. Stöckelhuber, A. Wenger, H. J. Schulze

"An important elementary step of the flotation process is the forming, drainage and rupture of a thin intervening liquid film between bubble and mineral particle.After the encounter of the bubble with the solid surface a wetting film is formed. The initial thinning of this film is driven by the capillary pressure inside the bubble. When the film has reached a certain thickness rupture can take place.There are two possible mechanisms describing this process:-, Growing fluctuation waves (spinodal dewetting) on fluid interfaces under the influence of any kind of attractive forces (electrostatic, van der Waals). -, Nucleation inside the film.Metastable wetting films on negatively charged, hydrophobic glass surfaces (gaseous phase methylated), or on hydrophilic, positively charged glass surfaces (with Al3+ ions), have been analysed by means of the kinetics of film thinning according to the Reynolds law. These experiments demonstrate that both mechanisms can be responsible for the rupture of a thin wetting film. In the case of hydrophobic surfaces the nucleation mechanism is preferred; in the case of opposite charged silica surface the capillary waves mechanism due to an attractive electrostatic double layer force between silica and air bubble takes place.Hereby the existence of a long range hydrophobic force. on a hydrophobic surface can be excluded. The apparent interaction can be explained by the presence of gas nuclei formed on heterogeneous surface sites. The results provide deeper insight into the mechanisms of wetting film stability, adhesion process in flotation and droplet coalescence."

Jan 1, 2003

By A. Norori-McCormac

"Air recovery, the fraction of air entering a flotation cell that overflows the cell lip, is linked to flotation performance, and it has been shown through industrial testwork that operating flotation cells at air rates that yield the Peak Air Recovery (PAR) results in high mineral recovery. For operating parameters over which flotation plants have little control, such as particle size, investigating the effect on the position of PAR, and the subsequent effect on flotation performance, proves more challenging. To this end, we have developed a bench scale flotation system that runs continuously and exhibits froth behavior similar to that found industrially, allowing the study of such parameters as particle size in addition to air rate. The bench scale system comprises a 4 l baffled cylindrical flotation cell, stirred by a Rushton impeller. The concentrate is recycled back into the pulp, allowing for continuous operation. Glass beads are used as solid particles, allowing a wide range of particle sizes to be tested, with TTAB as collector and MIBC as frother. The system allows operation at air rates typical of industrial flotation systems (1 -2 cms-1 superficial gas velocity), in addition to yielding a froth that coalesces and bursts and exhibits a peak in air recovery as cell air rate in increased. Solids and water recovery is also measured. The results show that air recovery is sensitive to changes in particle size. The intermediate size distribution showed a peak in air recovery (PAR) that corresponded with the maximum solids flowrate, as found industrially. It is shown that finer particles do result in more stable froths and higher recoveries, particularly at low air rates. The effect of particle size on the position of PAR is not yet unequivocally determined from these results."

Jan 1, 2014

By Bern Klein, Givemore Sakuhuni

Flotation is the dominant base metal extraction technique and it requires ore to be ground below the liberation size for effective recovery due to its dependence on mineral surface properties. For a poly-metallic ore, differential hardness of constituent minerals leads to over grinding of softer minerals before the harder minerals are fully liberated, which makes selection of a target grind size complex, and the complexity increases when treating leaner ores. Flotation recovery deteriorates above 100 and below 10 microns causing significant loses of valuable minerals in most flotation circuits. Although enhanced gravity concentration is known to be effective at recovering particles above 100 microns, which are difficult to hydro-dynamically transport, exploiting differential specific gravity for base metal separation was not an option in the past. This was partly due to the absence of high mass yield gravity techniques. The advent of continuous gravity concentrators with flexible mass yields, in the past two decades, has necessitated investigation of possible base metal applications. The Knelson CVD, one of the continuous discharge centrifugal concentrators, has an established application niche for sulphides associated with gold. However, its base metal applications have never been rigorously tested. Considering the dependence of flotation recovery on particle size, continuous discharge centrifugal concentration can be integrated in flotation circuits to capture flotation non-recoverable coarse particles. This paper explores how particle size, liberation and mineral hardness influence application of continuous centrifugal technology to regulate galena deportment in a polymetallic base metal plant. The results show that particle size affects galena recovery more than liberation. In view of these results, the CVD can be integrated in the primary grinding circuit to pre-concentrate the heavy sulphides at a coarser grind size with potential grinding energy savings.

Jan 1, 2014

By I. Kairyakov

The present paper is about the restoration of the molybdenum production in the floatation plant of Ellatzite-Med AD in Bulgaria. The process, based on a working design, includes the construction of a new floatation molybdenum section in the existing molybdenum department of the Floatation Plant using the so called Vemco inert-gas floatation machines, made especially for the molybdenum floatation. While in the ordinary floatation machines, block impellers create suspension of the air, sucked from the atmosphere with the slime particles of the concentrate, which creates conditions for oxidizing the reagent, Vemco inert-gas floatation machines are covered with hermetic lids and the air inside the chamber is used. The technology, suggested by Geotechkoper Ltd. for making the working project, employs special machines from Dor Olliver Aimco, suitable specifically for molybdenum floatation in order to reduce the oxidizing of the reagent sodium hydrosulphate. Also the transport of the chamber product is done in hermetic conditions as the molybdenum flotation is done in two floatation rows and refining operations 3 to 8 are placed in the second row. Thus in the basic molybdenum floatation together with the first and second refining operations, which are hermetically closed, an ambient condition with low content of oxygen is created, that is about 8% for oxygen and about 92% of nitrogen, in which the oxidizing process is extremely reduced. This in turn results in reducing the consumption of the reagent depressor ? sodium hydrosulphate. In that way there is an improvement of the economical indices of the molybdenum production.

Jan 1, 2014

By Alejandro Uribe-Salas, Fabiola Nava-Alonso, Gloria Dávila-Pulido

This paper presents results of an experimental study performed on the role of calcium sulfate present in flotation water on sphalerite flotation in the Pb/Cu circuit (non Cu-activated sphalerite) and in the Zn circuit (Cu-activated sphalerite). In the Pb/Cu circuit calcium ions adsorb on the negatively-charged sphalerite favoring xanthate adsorption and therefore making sphalerite floatable; experimental measurements show sphalerite contact angle increases with calcium concentration while xanthate adsorption onto sphalerite increases with the increase of pH and calcium concentration. Gypsum (CaSO4·2H2O) eventually present due to calcium sulfate precipitation is not detrimental to flotation at this stage since it is negatively charged at pH 9 and therefore, does not adhere onto the surface of negatively-charged sphalerite. In the zinc circuit, Cu-activated sphalerite decreases its negative charge (or even becomes positively charged) and develops some hydrophobicity due to the polysulfide produced by Cu-activation. At this stage calcium ions do not interact with the mineral surface and therefore do not favor xanthate adsorption; nevertheless, precipitated gypsum particles do adhere onto the mineral surface, greatly affecting its floatability (e.g., contact angle). Addition of sodium carbonate to dissolve gypsum and to precipitate calcium as calcium carbonate, which disperses in the bulk of the suspension, effectively restores mineral hydrophobicity. SEM observations coupled with EDS analysis clearly illustrate and support the above sequence of events.

Jan 1, 2014

By B. S. Moroney

Elemental distribution varies widely in the ores, minerals and beneficiated products depending on the constituents. Accurate analysis of each element present in various beneficiated products is utmost required to assess the grade in view of zero waste technology. Hence, the suitable methods and instrumental technique is of prime importance as the distribution of various elements differs in the beneficiated products. Conventional classical technique of analysis is absolute and due to this, it has not become obsolete. Besides, it is much needed for making standards for various relative techniques. Instrumental techniques comprising of X-ray fluorescence, Induced Coupled Plasma Analyzer, Carbon-Sulphur Analyzer, Atomic Absorption Spectrometer etc. are important for quick and accurate analysis. However, the selection of these instruments depend on the nature of material to be analyzed. This paper highlights the importance and use of various methods/techniques and instruments involved in the analysis of various ores, minerals and beneficiated products. Keywords: wet classical, x-ray fluorescence, induced coupled plasma analyzer, atomic absorption spectrometer

Sep 1, 2012

By Hans-Åke Häggblad, Bertil I. Pålsson, Jan Stener, Kent Tano, Andreas Berggren, Pär Jonsén

Numerical modelling of grinding in tumbling mills is traditionally done with the discrete element method (DEM). The grinding balls are then represented by DEM particles and the mill structure is considered rigid. To include more physical phenomena several numerical methods can be combined. One important improvement is to include the mill structure response, using the finite element method (FEM). The interaction between charge and lining can then be studied in detail. The pulp can also be included using a particle-based continuum method e.g. smoothed particle method (SPH). The strength of SPH lies in modelling of free surface flows and very large deformations and it is suited to model simultaneous fluid and granular flow. Still, the coarse particles (grinding balls) in the charge are suitable to be model using DEM. Each of these methods has their strength and weaknesses, but combined they can successfully mimic the main features of the charge movement. With these numerical tools the complex interaction between the different components of the grinding process; pulp, charge, lining and the mechanical behaviour of the mill, can be studied together. This work will present novel numerical approaches to model, simulate and validate charge behaviour in tumbling mills. These numerical models give possibilities to better understand the physical and mechanical behaviour of particulate material systems during grinding in a tumbling mill. This is important in order to develop and optimise future high-capacity grinding circuits and save energy.

Jan 1, 2014

By Q. Shi

An investigation into the hydrophobic aggregation of ultrafine smithsonite in surfactant solution has been undertaken through a combination of hydrophobic flocculation experiments, zeta potential measurements, surface tension measurements, and contact angle measurements. The experimental results have revealed that the behaviors of hydrophobic aggregation were closely correlated with the particle hydrophobicity, but they were not lowered byte change of the particle surface charges due to surfactants adsorption. On the other hand, the liquid (solution) surface tension (?LV) plays an important role in hydrophobic aggregation, and the hydrophobic aggregation could not occur below the critical liquid (solution) surface tension (?c). Meanwhile, this flocculation has been observed to require sufficient stirring strength and magnitudes of kinetic energy input to achieve the maximum aggregation degree. From the microflotation results, it has been found that the flotation kinetics response of smithsonite fines is markedly improved due to sufficient stirring strength, and the stirring strength influenced the floc flotation in a manner quite similar to their influence on the hydrophobic aggregation, suggesting that the formation of hydrophobic flocs is a promising means to recover smithsonite in the fine size range.

Sep 1, 2012

By Narasimha Mangadoddy

The complex nature of multi-phase flow in dense medium cyclones has restricted plant operators and designers to rely on empirical equations for predicting the performance. A number of empirical cyclone models have been developed in the past (Wood, 1990; Dunglison, 2002). In recent years, this subject has been broached with computational fluid dynamics (CFD). Most of the CFD models have not considered the correct rheological behavior of magnetite medium while simulating the medium segregation inside the cyclone. These models mostly predict excessive underflow volumetric flow rates. In this paper simulations of magnetite medium in a dense medium cyclone, were conducted in FLUENT where the particle phases were simulated using the modified Mixture model. The turbulence was resolved using Large Eddy Simulation (LES) model. The rheological behavior of medium was considered in the form of Granular viscosity, Newtonian and Non-Newtonian models corrected with particle loadings and fraction of ultrafines. Multi-phase simulations using granular viscosity option although predict the overall split product medium densities reasonably close to experiments, the mixture viscosity values are restricted to substantially lower values, similar to water viscosity. Simulations using Newtonian viscosity model corrected with particle loading, and fine fraction below 53µm size is predicting overall mixture viscosity levels well over water viscosity levels, but under predicting the under flow the underflow medium density. Multi-phase simulations using Non-Newtonian Herschel-Buckley model, calibrated for superfine magnetite medium measured viscosities, is closely predicting the medium segregation with gamma ray tomography data. Overall predicted product medium densities, underflow volume split are close to the experimental data. This model is can be further used to simulate coal portioning and hence in developing new designs.

Sep 1, 2012

By S. V. Petrov

Oxidised ores possess a significant share among raw materials which are treated by traditional plant technology. As usual, the chemical composition of these ores is rather simple. They can be treated by standard cyanidation. In this case, the resulting wastes have an alkaline reaction. Their toxicity (in case of ROM ores treatment) is mainly due to the presence cyanides and thicyanades. The tails are dexotified before disposal. However, chemical reagents used cannot provide a complete removal of toxic matters. In this case, this disposal poses a real problem because these tails contain a significant amount of CN and SCN and their behavior during a long disposal should be studied. A sample with a simple composition taken from cyanidation tails was studied. The sample presents itself the quartz low-grade sulfide gold-bearing ore. Sulfide sulfur content is 0.15 per cent,and heavy metals content is 0.023 per cent. Method of testing is described further. The samples were tested under moderate and subarctic climates based on the difference in temperature, moisture and the degree of oxygen saturation of air. The pH of water extract, which was prepared using distilled water, was also determined besides measuring the concentration of cyanides and thiocyanates. This demonstrates the stability of sulfide-bearing minerals in the disposed tails. The tests time was 820 days. It was found that the alkalinity of the samples tends to lower under oxygen-containing conditions in proportion to temperature increasing. Under conditions without oxygen, the pH lowering is minimal. Mineralogical and chemical properties of the ore material give positive alkaline balance during testing. The solid sample contains enough alkaline agents to compensate dangerous to the environment reactions of sulfides oxidation.pH value maintaining under alkaline conditions witnesses to the possibility of a safe disposal of this tails type. The largest amount of cyanide is removed under acid-containing conditions at positive temperatures. The higher the temperature is, the more intensive destruction is. At the moment, of finishing the tests at 20ºC temperature, the residual concentration of CN- was 0.06-0.10 mg/L, at 4ºC, the residual concentration of CN- was 0.2-0.3 mg/L and at -18ºC was 0.4-0.6 mg/L. Under conditions with the lack of oxygen, cyanides can be removed within the first 200 days. Then, this process fully stops. A stabilized cyanides concentration is 3.0-4.0 mg/L. The presence of sulfides increases the content of cyanides at the initial stage of testing. Then, the concentration of SCN at the temperatures above 0ºC decreases rapidly under oxygen-containing conditions. At the rise of temperature, a narrowing of peak at the curve and an increase of the destruction process are observed. At the end of testing, the concentration of thiocyanates in the moisture of wastes was 0.2-0.3 mg/L at the temperature of 20ºC and 0.5-0.6 mg/L at the temperature of 4ºC, respectively. The concentration of thiocyanates contained in a frozen sample and media which have the lack of oxygen stabilizes at a certain level owing to sulfides and does not practically change further. It was found that detoxification of oxidized cyanidation tailings with a simple composition which were disposed as filtration cakes can be possible. In this case, the concentration of cyanide in the moisture of disposed wastes can have a close value or equal to actual concentration during cyanidation. In order to meet the requirements of high ecological safety standards and successful detoxification process of toxic compounds in the tails under the action of natural factors, the conditions of air aeration with oxygen for the whole volume of tails are required. Keywords: cyanides, thiocyanates, storage, detoxification, flotation cakes

Sep 1, 2012

By S. Swaroopa

Copper-chromium mixed oxides are widely used as catalyst for organic chemicals industry, NOx and CO oxidation, solid propellant etc. In the present investigation, one such spent Cu-Cr catalyst has been tested for recovering copper and chromium values through hydrometallurgical route. The spent catalyst used in this study contains about 42% Cu and 36% Cr. Phase analysis through XRD indicates that major phases are copper chromium oxide (CuCrO2) and copper chromate (CuCr2O4) while minor phase is copper oxide (Cu64O). SEM images show that high energy ball milling changes surface morphology significantly ? more regular shaped grains in unmilled samples changed to fine agglomerates. Surface area also changes significantly due to milling. Preliminary leaching experiments with NH3 and H2SO4 media using unmilled samples indicate that both the media are suitable for selective extraction of copper. About 55% copper recovery is achieved in 2 h using 1.2 M NH3 + 0.2M (NH4)2SO4 solution at 100°C. Increasing NH3 concentration or temperature does not improve the recovery significantly. Under the above conditions chromium, dissolution is insignificant (max. 2.24%). XRD analysis of the residue indicates that copper chromate fraction (CuCr2O4), which is a spinel structure, remains mostly intact. In sulphuric acid media at ambient temperature, 47% copper recovery is achieved with 7.5% (v/v) H2SO4 and maximum of 57% with the increase in acid concentration to 20%. However, 67% recovery is achieved by increasing the leaching temperature to 150°C. High energy ball milled samples show improved leaching efficiency. Under the leaching conditions of 7% H2SO4 (v/v), 2% pulp density, 80°C an unmilled sample yields 47% Cu recovery whereas 3h and 5h milled samples yield 65% and 90% Cu recovery respectively in 2h leaching time. Influence of temperature is also more pronounced in milled sample leaching in comparison to unmilled sample. Water leaching of alkali (NaOH) roasted milled sample carried out at 750°C for 2 h with 100% NaOH (w/w) resulted in 80% Cr recovery as compared to 37% Cr recovery using unmilled sample under the same conditions. Keywords: spent catalyst, copper, chromium, leaching, mechanical activation, roasting

Sep 1, 2012

By Rintaro Hayashi

The enrichment of useful components from ores and/or wastes has become important with increasing recent worldwide resources demand and the amount of wastes generated from the urban mines, in order to establish real ?sound resource-cycle society? including the activity of resource exploitation. The first stage of the treatment in the process must be comminution and it is important to make good liberation among compositional phases in the targeted resources. Electrical disintegration (ED) is well known to make a selective breakage at phase boundary. However, the detailed mechanism of the phenomena is not clarified yet, in especial, on the influence of electrical properties of compositional materials on the liberation. This paper made a comparison between the liberation degrees of ED products and the results of electromagnetic field analysis using finite element method (FEM). In the experiments, we used several synthetic cement paste based samples in which mineral particles were dispersed to apply the ED, and in the electromagnetic field analysis, we calculated the charge density accumulated and the Maxwell stress at phase boundary. It was found, for highly insulating mineral samples, that higher breakdown voltage was necessary because electric charge was not easily accumulated at phase boundary but that higher liberation degree was obtained after the breakdown (ED). It was also found the tendency that higher liberation was observed for the samples which had higher maximum Maxwell stress calculated by the electromagnetic field analysis. From the results, the electrical charge and Maxwell stress induced at phase boundary could be driving forces of selective breakage. In addition, we also applied the ED to the printed circuit boards (PCBs) in order to concentrate miner rare metals, which were essential for producing electronic devices. It could be demonstrated that the devices installed on the PCB were easily detached from the board and that most of metal elements in the devices was exposed and liberated from the insulating plastic covers, which were broken in the ED, then, it is considered that the subsequent solid phase separation could be effective for concentrating such metal elements. Keywords: liberation, electromagnetic field analysis, printed circuit board, miner rare metal

Sep 1, 2012

By Heinrich Hutchison, Thomas von Moltke, Roelof F. Sandenbergh, Katarina P. Cerovic

In the leaching of gold in aqueous cyanide solutions the rate of gold leaching may be decreased by the passivation of the gold, that may however be prevented or reversed in the presence of lead species in solution. In the present study potentiostatic, potentiodyanamic and XPS (X-ray photoelectron spectroscopy) analysis were used to further clarify the action of lead ions on the anodic activity of gold in alkaline cyanide solutions. It was found that lead increased the gold dissolution rate as it deposited on the gold surface at potentials more positive than its reversible Nernst potential for bulk metal deposition, i.e. by underpotential deposition mechanism, but that it decreased gold activity if present as bulk plated lead on the gold.

Jan 1, 2003

By Gurubasayya Swamy

This paper presents the performance study of sag mill in the processing of gold ore. Deterioting ore grade and high demand of metals has tremendously influenced the SAG mills. Today?s high capacity Semi-autogenous grinding (SAG) mills expand vast amounts of energy and in doing so consume tons of shell liners and steel balls, while processing ore. Semi-autogenous (SAG) mill performance is influenced by ball charge, feed properties, shell, grate, and pulp lifter design. In the performance study of SAG mill, based on the results obtained it can be observed that SAG mill performed better at feed size +4 inch and grinding media consumption 0.90kg/mt. In the present study the effect of crusher bypass on SAG mill performance, an immediate drop of throughput ranging from 10-20tph is observed. Keywords: sag mill, pulp lifters, grinding media, energy, consumption, throughput

Sep 1, 2012

By J. Sachweh

The last few years have shown a significant increase in the demands for fine products, which means everything under 10µm. There are more and more applications requesting extremely fine ground powders leading to the development of several milling machines which are better adapted to the new products. Cost saving machinery is important for the worldwide competition. Especially the energy consumption is extremely important for any fine ground product. A worthwhile field for mechanical engineering companies is the dry milling machinery as there are not as many solutions available compared with wet milling applications. In many cases wet mil-ling is the only solution to reach the requested quality, but there are also a lot of applications which can be performed in a dry way on the premise that the right mill and classifier are available. Dry milling permits to save energy and allows to influence the particle size distribution more easily, as a classifier can be used in that case. This will significantly reduce production costs and can enable the production of new products with better properties. The Tower Mill is well-known already in the field of wet grinding. Recent research work and end user reports have shown clearly that this mill has a lot of advantages compared to a ball mill. Up to now this advantage is limited to wet grinding as only few mills have been used for dry grinding. There is no doubt about the efficiency of dry grinding, but new and improved feeding and discharg-ing systems have to be developed in order to enable the full range of its advantages. Especially the high production capacities are a challenge for mill and classifier designers. The Tower Mill with its special grinding mechanism allows to cope with very high feed rates, because machines with more than 1 MW are available. Improved grinding efficiency will decrease the circulation load through the classifier and also lead to smaller classifier sizes. Together with im-proved mills the classifier can work more efficiently because the feed material is finer. Results of a test center plant production will be shown together with a comparison between stan-dard machinery and the MaxxMill®. Preferential applications for each mill will be explained.

Jan 1, 2014

By H. Z. Kuyumcu

Coking of coal blends using high volatile coals with poor coking abilities to produce a high quality coke for blast furnace application can be achieved by compacting the coal blend prior to the carbonization process. Here densification up to a relative material density of 80 %, i.e. a compact density around 1100 kg/m3, has proven to be advantageous. Coal is compacted by stamping, if the so-called stamp charging process applied. Compacting of the coal by pressing is practised in case of the cokemaking with so-called heat-recovery ovens. Stamped and pressed coal cakes require over the cake volume uniform high density and mechanical stability. Besides the aspects of the coal selection, the efficiency of the process is mainly determined by the operating parameters compacting time and compacting energy for coal cake making. At the Department for Mechanical Process Engineering & Solids Processing of the Technical University Berlin the two sub-processes of densification and strengthening during stamping and during pressing are theoretically and experimentally investigated using specially developed lab-scale compacting test units and a strength test device. Describing cake density in terms of coal properties for a given coal and measured compacting energy input then leads to a compacting equation with the so-called Stampability as the integral model parameter for the stamping process. For the pressing process the cake density can be calculated with the measured compacting pressure and the Compressibility factor, respectively. Investigations were carried out to provide evidence of a significant influence of coal type, coal surface moisture, coal granulometric and mechanical properties on the densification process. The overall objective of the work is to establish a comprehensive mathematical model on the compacting behavior of large coal bulk quantities and the optimization of the compacting processes by stamping and by pressing. Keywords: coal compacting, agglomeration, stamping, pressing, cokemaking

Sep 1, 2012

By J. Drzymala

Ores and raw materials are subjected to mineral processing operations to increase the content of their useful components. Upgrading of these materials can proceed with different selectivity and therefore, there is a need to know and monitor the separation results of the process. The separation results can be evaluated using tables and graphs called upgrading curves. The course of lines in the upgrading curves is usually complex and depends on the graph type and process parameters. The Halbich grade vs. recovery plot is frequently used because is practical and it indicates several characteristic features of separation results. Separations by means of flotation of several different shale, dolomite and sandstone copper ores were performed along with determination of their mineral composition, copper content, liberation degree, and the maximum theoretical copper content in the first concentrate. These data, plotted as the Halbich upgrading curves, allowed to find other characteristic points such as practical maximum copper content in the first concentrate, maximum curvature coexisting with the liberation degree, maximum recovery of ore valuable components, and the slope the recovery-grade line at high recoveries as a measure of liberation. Correlations between theoretical and practical maximum copper contents in the first concentrate as well liberation degree and maximum curvature were also presented. They show that the ore type significantly influences the shape of the Halbich curve and its characteristic points.

Sep 1, 2012

By H. Mengbing, A. Potokin, A. Usov

"Revealed and analyzed in the study are the ways of significant perfection of specific characteristics of the equipment, such as use of high-frequency voltage transformation to create a charger; use of pulse transformers, with core made of materials with high magnetic permeability, in pulse generating circuits; as well as use of special ways to produce voltage pulses with a short front. The experiments have proved the possibility to adapt these technological solutions for electric-pulse installations, and suggested on this base is a strategy of further development and application of electric-pulse technologies. The different applications joint work schemes of voltage sources with two levels voltage and energy in electric pulse technologies are investigated. The possibility of increasing energy efficiency of destruction is shown."

Jan 1, 2014

By T. N. Aleksandrova, A. V. Afanasova

"The research is aimed at solving the problem of enrichment of sulphide ores, counting for more than 40% of the reserves in Russia. The aim of the research is to develop and scientifically substantiate the scheme for processing this type of ores in order to extract fine-dispersed noble metal particles (FNMP). In this work samples of sulfide carbonaceous ore and flotation concentrates were analyzed using complex precision methods of analysis: electron microscopy, spectral analysis with induction plasma, complex thermogravimetric analyzes, etc. Data on the composition of the organic constituent of the samples were obtained with the usage of complex thermogravimetric analysis. The presence of various types of kerogen and bitumen has been established. Experimental studies on the coarsening of FNMP from the initial ore and flotation concentrates using electromagnetic radiation have shown the effectiveness of this coalescence method. The data on the elemental composition of the samples and the amount of FNMP were obtained. Thus, studies on the extraction of FNMP from carbon sulphide ore have shown the possibility of effective usage of combination of electromagnetic action and classical enrichment methods to extract fine particles of noble metals. INTRODUCTION Due to the depletion of free-milling raw materials the involvement of new types of deposits is the strategy of developing mining industry of Russia. The black shale raw materials show interest as a non-traditional source of precious metals since its genetic and positional gold-carbon connection. Muruntau, Sukhoi Log, Bakyrchik, Natalkinsky, Nezhdaninskoye, Olimpiadinsky, Homsen and others are the examples of well-known deposits of the black shale formation [1]. In fact the main gold-dispersed regions of Russia are composed of black-shale strata. Review of literature [2-5] shows that in recent years in almost all deposits of the black shale formation metals of the platinum group (PGM) were detected that significantly increases their practical importance."

Jan 1, 2018