Search Documents

By Sanja Miskovic, Manjunath Basavarajappa

Numerical investigation of fluid flow characteristics and mixing efficiency of different impeller designs, based on the mixing characteristics of a passive scalar/tracer, is conducted using CFD for lab scale flotation cells of diameter D and height H equal to 300 mm. Fine computational mesh containing close to 1.6 million cells is used to obtain fully resolved steady state flow field close to the impeller. Unsteady scalar mixing simulations are performed on a relative coarse grid consisting of approximately 450,000 cells. Based on detailed numerical simulations, flows are fully characterized for four impeller designs at two off-bottom clearances C of 50 and 25 mm (D/6 and D/12). Passive scalar is injected from the cell bottom and the time required to attain uniform concentration distribution inside the cell volume is taken as the mixing time by monitoring scalar concentration at four discrete locations. The effect of varying agitation speed and off-bottom clearance on mean flow characteristics is also investigated. The scalar mixing results reveal regions of low mixing efficiency and are used to understand mixing process in greater detail. Through the previous research work, it was found that the main flow pattern undergoes transition from double-loop to single-loop configuration with decrease in off-bottom clearance below a certain critical height for stirred tanks using flotation impellers in the absence of stator. The inclusion of stator is found to alter the mean flow behaviour by preventing the jet from transitioning to axial type flow for lower clearance. Power numbers for different impeller designs are calculated based on the torque generated on impeller blades, and also from the total turbulent kinetic energy dissipation in the overall fluid volume. Power number is found to exhibit a significant dependence on off-bottom clearance based on the CFD results.

Jan 1, 2014

By Cristian Melipichun, Leopoldo Gutierrez

The effect of the presence of fine particles of kaolinite and montmorillonite on the induction time for attachment of bubbles to particles of a copper concentrate rich in chalcopyrite was evaluated in this study. The results obtained from induction time measurements were correlated with data of concentrate recovery achieved from micro-flotation experiments. The effect of the presence of fine clays on the stability of air-water foams was also studied through measurements of the foam volume generated in a glass column under different conditions of air flowrate and MIBC concentrations. The experimental results showed that induction time values increased under the presence of fine clays. These data agreed with results obtained from micro-flotation experiments that showed that copper concentrate recovery decreased when clay particles were added. Although a complete explanation for these results is not available, the fact that experimental observations indicated that fine clay particles tend to adsorb on gas bubbles, suggests that the interactions between fine phyllosilicate particles and air bubbles have to be taken into account when studying the effect of clays on froth flotation. Foamability tests showed that the presence of fine clay particles increased the foam volumes only at high additions of clays and low dosages of MIBC. The results obtained at higher dosages of MIBC showed that the foam volumes decreased with the addition of clays under all the experimental conditions tested.

Jan 1, 2014

By Nóra Schreithofer, Zoltán Jávor, Kari Heiskanen

"One of the challenges the mineral processing industry is facing is caused by the fact that water resources in mining areas are becoming very limited and the cost of water is increasing. The water sources in arid regions often have high salt content. Environmental regulations are forcing plant operations towards completely closing the water cycles within plants. This means that impurities (salts, reagents, ions dissolved from minerals, etc.) accumulate within the circuit that will affect the flotation performance. Water purification can significantly increase the operating costs therefore it should be carefully considered weather the impurities need to be completely removed or is there a tolerable level of impurities that can still be left in the process water without significant deterioration of the flotation performance? Several additional questions arise: what are the tools that help identify what is a tolerable level of impurities? How do the different impurities interact and what is their effect on the process? The effect of frothers on the dynamic properties of air/liquid interface in different size-scales has been extensively studied by the authors in the past. Based on these studies a frother characterization framework was developed that systematically examines the dynamic surface properties of the air/liquid interface in relation to the bubble size. This work can be considered as tool that could be used for the above mentioned purpose. The present study investigates weather the same frother characterization framework can be applied for systems where both frother and different types of salts are present. Nasfroth 240 was used as a frother, in combination with structure-breaker KCl or structure-maker NaCl and CaCl2. Bubble size measurements in laboratory scale mechanical flotation cell and laboratory flotation column and dynamic surface property measurements (dynamic surface tension and dilatational elasticity) were performed. The results highlighted the addition of salt to the frother solutions significantly decrease the bubble size and increase the froth high. The coalescence behavior of bubbles showed correlation between the D32 and ionic strength of salts. The results highlighted that the studied structure maker and structure breaker salts effect the dynamic surface properties in different way."

Jan 1, 2014

By Andrzej Luszczkiewicz, Magdalena Duchnowska, Jan Drzymala

A selected flotation system of beneficiation of the copper ore at KGHM Polska Miedz S.A. has been analyzed in the article. It was found that a proper assessment of upgrading must be based on two elements, that is the upgrading process selectivity and working point of the considered flotation unit, both determined, preferentially by means of the Fuerstenau recovery-recovery upgrading curve. The Cu recovery - non-Cu components recovery upgrading curve was selected for calculations because its background lines (no separation and ideal separation) are insensitive to changes in the grade of feed of the processed material. This approach allows a comparison of upgrading results for feeds having different grade, being upgraded in various flotation machines and under different physicochemical conditions. It was shown in the paper that the main criterion for comparison of two working in parallel systems is selectivity of upgrading. However, when two flotation machines, despite of the same selectivity, produce concentrate and tailing of different grades, it is necessary to analyze their working points using upgrading curves. The proper position of the working point depends on the criterion imposed on the process and is a result of not only basic parameters of the upgrading process such as feed, concentrate and tailing grades but also on economic parameters such as costs associated with the production of concentrates and the time needed for their production.

Jan 1, 2014

By Igor P. Solozhenkin, Peter M. Solozhenkin, Sanda Krausz

"In this work, authors will show the efficiency of computer technology and chemical programs at studying collectors for flotation of minerals of elements of platinum group (EPG). Clusters various minerals EPG (flotation reagents) are created, named us clusters minerals (reagents) as their structure corresponds to the chemical formula, and the distance between separate atoms corresponds to the known tabulated data. By molecular modeling are investigated clusters sperrylite PtAs2, stumpfilyte PtSb, sadberryte PdSb, sobolevskite PdBi, palladoarsenyte Pd2As, paolovyte Pd2Sn, rustenburgyte (Pt3Sn, Pt6Sn2) and their computer parameters (absolute rigidity, electronegativity, transfer factors of carry, charges of the atoms) are determined. Tellurides of palladium (IV, II) merenskyite PdTl2 and kotulskyte PdTe and platinum clusters are investigated: PtFe4, Pt3Fe, PtFe (Pt2Fe2), Pt2Fe (Cu) Ni. The technique of attachment of the collector (composites) to cluster atoms EPG is offered. For the first time, it is established that at linkage of flotation collectors on monodentate, bidentate and bridged to circuits with atoms clusters the minerals containing atoms As, Sb, Bi, Pb, Sn, reaction of connection with change of a degree of oxidation of these atoms and occurrence of a proton operates. It is executed virtual skirling organic compounds connections by the developed criteria from accessible libraries of a database. The principle of an estimation of interaction energy for flotation reagents with mineral clusters is offered. It is developed the prognosis of collector activity evaluation (P?AE) and his values for candidates in collectors for flotation of minerals EPG are calculated. For flotation of ores containing Pt and Pd minerals, a number of reagents, including compounds on basis P (III), for innovational technology of Pt, Pd mineral flotation are recommended. Key words: flotation, minerals, flotation reagents on the basis of phosphorus (III), molecular modelling, chemical programs, program ????? , electronic energy."

Jan 1, 2014

By Leena Vesa, Antti Remes

Design of thickeners is based on laboratory test work, characterizing the material and determining the optimal reagents, dosages and settling regimes. Several methods for dimensioning plant scale equipment exist. Kynch and Talmage-Fitch design procedures has been applied widely for a long time. Nowadays, besides them, a dynamic laboratory test work is applied for design of high rate thickeners. In that the laboratory unit is operated with known solids load per area, feed and flocculation conditions and with raking of the underflow. All these test methods afford useful data for setting up and calibrating a dynamic simulation model of a plant scale thickener. This paper presents a flocculation kinetics based dynamic thickener simulation model and a procedure to calibrate the model parameters. With the model, the underflow stream composition can be simulated over time as a function of the thickener operating parameters, which are: the feed rate and composition, underflow pumping rate, flocculant dosage and dilution of the feed. In addition, the model incorporates calculation of the slurry bed level, the cone pressure, the yield stress and the rake torque. Such a dynamic modeling scheme enables setting up simulation aided operator trainings and developing and testing of advanced control strategies, for example. The unit model can be integrated as a part of concentrator-wide flow sheet simulation model as well. Here, calibration of the kinetic flocculation model based on a laboratory test case data and further the operation of a simulated plant scale thickener are presented.

Jan 1, 2014

By Hamid-Reza Manouchehri, Hassna Aitahmed-Ali, Stellan Sundberg

"In flotation practices as the particle size becomes fine, e.g., p<20µm, the process efficiency declines markedly. When flotation of fine particles is necessary, one method to improve the recovery is selective agglomeration of fines. Different agglomerating methods have been introduced and tested; however, one method which has recently received great attention is to aggregate fine particles by magnetic force. A selective aggregation of the fine paramagnetic particles, e.g., sulfide minerals, can be achieved by applying a high intensity magnetic field during flotation conditioning. The method is simple, selective and effective for fines, and has a low operation cost. However, a minimum magnetic susceptibility of fine grains is required for this process. This method has been demonstrated in different sulfide minerals flotation plants. The implementation of the magnetic conditioning device, ProFlote, in both the Cu-Pb and the Zn circuit of Boliden’s Garpenberg plant in Sweden, where a complex massive sulfide ore is treated, is discussed herein. The preliminary results have shown an increase in the recovery of value minerals, in particular Zn and Ag and considerable reduction in Zn deportment to the final tail. Increases in Cu grade and decreases in Pb grade in Cu-con have been achieved as well."

Jan 1, 2014

By B. McFadzean, K. Moller

"The mechanism whereby thiol collectors adsorb onto a mineral surface has been widely studied. Most of these studies examine the mineral surface at equilibrium state and, often, well above monolayer coverage. However, the formation of species at the mineral surface is a complex process that is both kinetically and thermodynamically controlled. In a typical industrial application, the dosage of collector will be around monolayer level. This study uses isothermal titration microcalorimetry to measure the heat evolved during the reaction of sodium ethyl xanthate (SEX) and sodium isobutyl dithiocarbamate (SIBDTC) and their mixtures with galena and chalcopyrite. The sensitivity of the instrument allows heats of reaction of sub-monolayer quantities of thiol collector to be measured.The study found that both the magnitude and kinetics of the reaction between a collector and a mineral surface was dependent on the type of mineral and the type of collector. Proposals are made for the reactions based on literature and the evidence from this investigation. It was found that when collectors were reacted with mixtures of galena and chalcopyrite, that the magnitude of the reaction was lower compared to that measured for the pure minerals alone. This may be due to galvanic interactions between the minerals, resulting in a passivating effect on one or both of the minerals."

Jan 1, 2014

By Érica Linhares, Anderson Silveira Lopes, Aline Costa

In the production units of ferromanganese alloys wastewater are generated. They mainly arise from gutters of drainage water from warehouse of raw material (manganese ore, reducing agents and other), product and slag. This wastewater, in general, may contain particles that will suffer difficulty to naturally decant, giving the water turbidity and color characteristics. Thus, this study aims to characterize the effluent, the treated water and the sludge from the sedimentation tank from the one main Brazilian plant. The investigated characteristics were: turbidity, total solids (TS), suspended solids (SS), dissolved solids (DS), pH, Eh, COD (chemical oxygen demand), residue classification and chemical analysis by ICP - OES. The turbidity before treatment was 417 NTU and after passing through the tank, 44 NTU, a figure slightly higher than the emission standards for Class 1 regulated by the Brazilian environmental legislation in force. The values for TS, SS and DS of the effluent were 225, 114.3 and 110 mg/L, respectively. For the treated water the values were 93, 48.3 and 45 mg/L for TS, SS and DS, respectively. The sedimentation process was able to reduce by 21 % of the COD. In the test of loss on ignition (LOI) from the tank bottom sludge were observed losses of 29.35 %, while the volatile analysis found 20.70 % of volatiles in the sample. It was determined that the concentrations of Al, Fe, Mn and S are, respectively, 0.1875 mg.L-1, 0.3071 mg.L-1, 0,789 mg l-1 and 0.00828 mg.L-1, values above the maximum allowed by law. Based on the analysis of X-ray diffraction, the identified minerals in the sludge were quartz, muscovite, kaolinite, calcite and albite.

Jan 1, 2014

By I. V. Makarskii, D. N. Nikitin, L. G. Tarasova

"The extent and nature of the damage to diamonds at processing plant is largely determined by the design features of the equipment, the characteristics of the feed ore and the parameters of the ore disintegration process (change in the rotational speed of the autogenous mills, variations of the water supply to comminution process, choice of the optimum charge, etc.). To monitor the intactness of diamonds, an instrumental method using the X-ray tomography system and colored synthetic indicator diamonds was developed for identifying the process-related damage. The X-ray tomography system consists of a CT-Portable X-ray tomographic scanner, a crystal positioning device and customized software (developed by the Fraunhofer Institute and Aliud GmbH, Germany). The developed method enables improvement of the accuracy of the results, exclusion of the subjectivity of the mineralogical assessment, acceleration of data processing and promptly planning of the activities aimed at reducing the process-related damage to diamonds. KEYWORDS Diamonds, colored indicator diamonds, process-related damage, loss of mass, instrumental method, X-ray tomography system. INTRODUCTION Industrial tests of ore processing technology at the enterprises of ALROSA PJSC are accompanied by assessment of the process-related damage to diamonds. The assessment of the process-related damage to crystals is carried out for prompt elimination of factors contributing to the increase of impact forces in the process flow sheet of ore treatment plant. For this purpose a specially selected parcel of -4.0 + 2.0 mm sized natural indicator diamonds is used. The diamonds are exposed to ionizing radiation in order to turn them green and thus to create a distinctive feature. Colored natural indicator diamonds are described, photographed in several views and introduced into the process flow sheet of the processing plant, then extracted from the process flow, described and photographed again. The comparison of diamonds before and after their passing through the process flow sheet of the plant allows to find evidence of process-related impact on the crystal and to calculate the factor of process-related damage (the number of crystals damaged during liberation and recovery), the loss of crystal weight and the degree of damage to the crystals. The method of colored indicator diamonds is used to select processing methods, equipment or regime which would be the safest for diamonds based on the analysis of the factors of process-related damage. There are limitations of the method, such as:"

Jan 1, 2018

By Henrique Kahn, Daniel Uliana, Juliana Antoniassi, Viviane Shimizu

"Mineral exploration and geometallurgy require a large number of samples for physical, chemical and mineralogical assays. The combination of all these data and their spatial distribution define the ore variability. This is important in exploration programs and crucial in feasibility studies as well as at the production operation level. Ore mineralogical composition and its associations, characterizing the geological formation and mineralization, are the main keys to define the ore domains and its variability, which can be quickly assessed by cluster analysis and by modern automated mineralogy tools. One hundred and ten copper ore samples from Sossego mine, in Brazil were compared and classified by X-ray diffraction cluster analysis based on the position and the intensity of the diffracted peaks. Initially four ore types were categorized based on content of major minerals: quartz, feldspar, amphibole, iron oxides, mica and chlorite. Results showed a strong correlation between the grouping and the samples location in Sequeirinho and Sossego orebodies, with a straight link to types/intensities of hydrothermal alteration prevailing in each body, which reflects the mineralogical composition and thus the X-ray patterns. Samples from four recognized ore types were submitted to detailed automated mineralogical studies by electron beam image analysis and differ strongly from each other regarding their chemical and mineralogical compositions and relevant parameters for mineral processing. Chalcopyrite is essentially the only valuable mineral, occurring both as submillimetric grains included in other minerals and as larger crystals. Except for pyrite, other sulfide minerals occur as traces. Chalcopyrite liberation curves indicate that samples from Sossego have higher liberation degree than those from Sequeirinho. The proposed method proved to be very efficient and accurate to classify a large number of samples within a short time frame, allowing the distinction of the ore types regarding their mineralogical composition as well as the mineral processing parameters."

Jan 1, 2014

By S. Mohanta

The air dense medium fluidized bed separator which has been developed for the dry beneficiation of coal is recognized as a low cost and high efficiency process. The success of this separator for beneficiating any specific coal, alone or in combination with other processing methods, mostly depends on the characteristics of run-of-mine coal. Therefore, a thorough knowledge of the mineralogical composition and washability characteristics of representative coal sample is highly essential for correctly and effectively assess the suitability of this process. Available literature conforms that although the characteristics of Indian non-coking coals are well known, the correlations between the particle compositions with its density are entirely lacking. In the present study the washability, proximate, ultimate and elemental analysis was conducted for four typical Indian high-ash non-coking coals and their elemental compositions were well correlated with the specific gravity of coal. The results obtained in this study provide some essential information to the coal-processing engineer for efficiently operate and control the process. Furthermore, the beneficiation potential of air dense medium fluidized bed was experimentally evaluated and compared with the results obtained from an operating wet beneficiation plant. Based on this comparative study the air dense medium fluidized bed is established to be a possible alternative to the conventional wet beneficiation method for beneficiating Indian coals with Ep values in the range of 0.03 to 0.06

Sep 1, 2012

By Takashi Furuyama, Sukeyuki Mori, Tetsuo Ikejiri, Abel Bissombolo, Yoshitsugu Koga, Masamichi Hata

In Japan, the increasing number of automobiles newly put into circulation is followed by a larger amount of end-of-life vehicles from which valuable metals are being recovered in shredder and related plants. Nevertheless, the processing of these scrapped automobiles which has reach a recycling rate of about 75%, generates a huge volume of waste, locally known as .shredder dust., which is commonly dumped on landfills. The saturation and depletion of valuable disposal sites in the near future, as well as the social and environmental problems related to the accumulation of these residues disposals are a major challenge for the automobile shredding industry. To promote an alternative way for the management of these disposals, the authors have initiated and developed a system for their processing, on the basis that more than 90% of these residues are combustible materials that could be used as refuses derived fuel. The developed processing system points out the mechanical/physical separation of shredded automobiles residues into two streams by means of an ascending airflow passing through a vertical zigzag separator and, the compaction of the light-density fraction of materials (that is about 60% of auto shredder residue recovered as float products and mainly composed of cotton, sponges and light plastics) to form a refuse derived fuel (RDF), the density, calorific value and ignition loss of which are 1.19 g/cm3, 4470 kcal/kg and 60.7%, respectively.

Jan 1, 2003

By Frank van der Meer, Lea Quincke

"High Pressure Grinding is applied to achieve size reduction of the particles by inter-particle breakage and to generate micro-cracks in the product particles as a contributing factor in e.g. leaching or mineral liberation. As alternative to classification, a closed circuit operation for HPGR can be established by product recycling, where a proportion of the coarser edge material and parts of the center material are split-off to be recirculated to achieve a finer final (center) discharge product for subsequent processing steps as ball mill grinding or beneficiation. As a result of the product recycling, the content of fines in the feed material increases and may affect the grinding efficiency in terms of production of fines and the generation of micro-cracks in the particles. In the scope of this paper, the effects of the proportion of fines in HPGR feed on grinding efficiency and micro-crack generation were evaluated. Grinding tests were executed with different feed size distributions, from a fines-void situation (truncated feed) to a fines-abundant situation (high product recycle). The evaluation of grinding efficiency and generation of micro-cracks was done by particle size analysis, Bond Work Index tests, impact tests on HPGR feed and products, and X-ray computed tomography of single product particles. This publication summarizes the main aspects of the outcome of these investigations."

Jan 1, 2014

By S. Gomez, P. A. Bebswa, A. N. Mwale

"The research aimed at improving the way screen performance analysis is conducted using a model that accounts for most feed and design parameters in its formulation. Thus, the aim was to validate the fine screen model that was developed at the Centre for Minerals Research (CMR) unit at the University of Cape Town. Fine wet screening is increasingly becoming an important application in fine grinding operations. Minera Saucito, a lead-zinc Mexican mine has replaced hydrocyclones with eight stacks of five decker derrick screens to close the ball mill in their concentrator plant. The five decker stacks have improved the overall plant throughput by 20% and have had the ball mill circulating load reduced considerably. As a continuous plant optimization process, a number of surveys were carried out to assess the performance of the 75 µm panel aperture installed screens. The surveys were conducted at seven different feed rates to the entire nest of screens to collect performance data. Using the fine screen model to analyze the results, it is found that as the feed rate increase, the sharpness of separation reduces. The CMR fine screen model was fitted to these results. The model fits the plant data with good accuracy. Simulated results based on this model are also presented.INTRODUCTION The potential of high frequency vibrating screens has long been identified as an alternative to hydrocyclones in grinding applications (Rogers and Brame, 1985). However, high frequency vibrating screens have had two main disadvantages, low capacity and high wear rates (Kelley and Mckeon, 2005; Teknikk, 2009). Current vibrating screen technology overcomes these challenges by multiple deck screen design and use of wear resistant urethane materials for panel construction (Kelley, 2007; Valine and Wennen, 2002). For a example, the Derrick screen’s material of construction is a tensionable urethane that provide high open area ranging between 35 to 45% with considerably reduced blinding (Valine and Wennen, 2002). Thus, there has been an increased uptake by the mining industry in the use of wet fine vibrating screens closing the ball mill as the final classification stage in the comminution circuit (Barkhuysen et al., 2010; Frausto, Ballantyne et al. 2017; Pelevin and Lazebnaya, 2009; Teknikk, 2009). Even though there is a number of models in existence, none of these models adequately predict the performance of high frequency vibrating screens (Karra, 1979; Rogers, 1982; Subasinghe et al., 1990; Trumic and Magdalinovic, 2011). Recently Mwale et al., (2016) developed a model for predicting the performance of high frequency vibrating screens using the partition curve properties. The input parameters of the model include screen open area (??) in m2, tonnage feed rate (????) (tph) and the weight fraction of solids (??) in the feed for a given panel aperture size. The model was developed based on data collected from a single deck industrial size derrick screen, in a pilot setup. The work presented in this paper is an attempt to test this model using data collected from Minera Saucito concentrator, an industrial plant whose comminution circuit is shown in Figure."

Jan 1, 2018

By Rebecca Hope, Derick Moolman, Frikkie Malan

"Despite the lip service that has been paid to pro-active plant maintenance processes over recent years, a significant portion of maintenance in industry is still reactive. The business driving force to prevent expensive production opportunity costs arising from “break-down maintenance” is obvious. Various benefits can be derived from successfully deploying remote equipment diagnosis technology and associated business processes.From an end-client’s viewpoint these include the ability to predict and take actions to prevent equipment breakdowns, increasing the lifetime of equipment by responding to appropriate operating instructions and therefore improving the return on capital expenditure. Better planning and scheduling of maintenance priorities and resources with performance measures like an Equipment Health Index are also possible. The knowledge that a qualified supplier engineer is constantly in touch with the operating conditions of their equipment, albeit remotely, is more than a comfort, and can be translated into quantifiable cost savings and improved supplier service levels.This paper analyses the reasons for the inadequate level of pro-active plant maintenance practice in industry today, and presents a number of important criteria in selecting appropriate solutions to this problem. A case study of a specific real-time, remote equipment management application is presented."

Jan 1, 2003

By Christopher Greet, Alfred Van den Bosch

"A range of media alloys with different chromium content has been developed for different milling applications. When selecting the grinding media alloy for a specific application, consideration must be given to the mineralogy of the ore as well as the water chemistry and mill operating conditions. The paper describes the influence of the microstructure of the alloy on the wear resistance and the influence of the chrome content on the pulp chemistry and downstream processing. It also provides information about the in-house tools which Magotteaux have developed to predict the media wear rate with different chromium content alloys and predict their flotation efficiencies that can be expected when the right alloy is selected for a particular application."

Jan 1, 2014

By Rajamani R. K.

The design of tumbling mills has progressed from the Bond work index concept of the 1950s to the population balance concept of the 1980s and then made a quantum leap forward with the discrete element method in the 1990s. The failure of a SAG mill at the Grasberg mine site set in motion the inquiry into the role of shell lifter geometry on the profile of the charge motion within the mill. Quickly, it became evident that this could only be accomplished by tracking individual motion of ore particles and grinding balls and not by study of en masse motion of the charge that had been established previously. The discrete element method (DEM) which was prevalent in the civil engineering literature at that time proved suitable to tackle this simulation problem. In 1991, the two dimensional simulation of laboratory scale mills was validated with the DEM. Later this simulation method evolved into ?MillSoft?? a simulation software package for the design of lifters in ball and SAG mills. MillSoft?simulations proved that cataracting charge motion is not conducive to the life of lifters. The old rule of thumb that the number of shell lifter rows should equal twice the diameter of mill in feet was shattered by simulation results. Instead, the number of rows equal to the diameter of the mill in feet, providing that the lead angle of lifter is around 25 degrees, was established as being more optimal. This bold design change was first implemented and tested by Mark Sherman at Alumbrera Mines in Argentina. Two 36-ft SAG mills responded extremely positively to the design change. This success was immediately repeated at Collahuasi, Pelambres and other mines in South America. The design change has so far exceeded expectation that there is not a single SAG mill around the world today that does not employ a relief angle on its shell lifter. The DEM method has advanced in the hands of the author, mining companies and universities, notably in Australia and South Africa. Today, three-dimensional simulation of charge profile and slurry transport is a standard in the design of mills. There is strong pursuit of a virtual comminution machine with DEM in Australia. In South Africa, an experimental method known as positron emission tracking is emerging as a method for tracking particles in grinding mills. The computational burden of computing with millions of particles in three-dimensional simulations has been eased to less than a day with a technique known as GPU computing. Keywords: DEM method, GPU computing, SAG mill, tumbling mill simulation, discrete element method

Sep 1, 2012

By L. Tavares

The significant capital and operating expenditure of size reduction operations have maintained comminution on the spotlight of mineral processing research during the last century and, more recently, the concerns about the impact of these operations on the sustainability of the minerals industry, will remain to do so in the 21st century. One of the most popular approaches that have been used to deal with these challenges is the application of simulation both to reduce the uncertainty in the design and improve the operation of size reduction operations. From the initially purely empirical approaches, including the energy size reduction ?laws? and the phenomenological approaches, of which the traditional population balance model is, arguably, the best example, comminution modeling now reached a point in which more fundamental and mechanistic models are sought. The paper analyzes some of the advances that now make multiscale modeling of comminution processes realizable. On the microscale, greater understanding of the phenomena involved in fracture and fragmentation of single particles under different stressing conditions now exists. Particle breakage testing methods are currently used in a routine basis by industry and good quantitative descriptions of different breakage mechanisms are now available, although research is still required to develop appropriate models for a couple of them. On the macroscale phenomena, the discrete element method (DEM) has been successfully used not only to provide insights but also quantitative information on the transfer of mechanical energy from the machine to the grinding media in mills and to particles in crushers, while smoothed particle hydrodynamics (SPH) and computational fluid dynamics (CFD) to describe fluid flow. The paper also analyzes the importance of modeling mesoscale phenomena in size reduction, which is the interaction of particles forming assemblies or beds of particles, demonstrating some of the areas requiring further attention. Examples of application of the multiscale modeling approach to the inadvertent comminution of ore lumps during handling, to the comminution in vertical impact crushers and tumbling mills are demonstrated. Keywords: comminution modeling, DEM, SPH, CFD, multiscale modeling approach

Sep 1, 2012

By Hideki Yamamoto, Norihiro Murayama, Junji Shibata

"Hydrothermal syntheses of zeolite from coal fly ash were carried out by using various alkali sources. NaOH, Na2CO3, KOH, K2CO3 and their mixture were applied for an alkali source of zeolite synthesis. The various physical properties of the reaction product, such as the kind of zeolite crystal, cation exchange property, surface texture and so on, was investigated through the zeolitization reaction from fly ash. The mechanism of zeolitization reaction was considered from these results.Zeolite P(NaP), hydroxysodalite(HS) and chabazite(K-CHA) are synthesized as zeolite species, when fly ash hydrothermally reacts in various alkali solutions at 393K. The crystal structure of the products obtained in NaOH solutions for 3h changes from NaP to HS with increasing NaOH concentration. K-CHA formation in KOH solutions needs 10h of reaction time, which is longer than that of NaP or HS.Dissolution, condensation and crystallization steps exist in the zeolitization reaction from fly ash, and the particle surface of products remarkably changes in each step. The fly ash is spherical particles and the surface is smooth(Fig.1(a)). The dissolution of fly ash occurs in the heating process until 393K, and the particle surface changes like unevenness(Fig.1(b)). In case of NaP, the condensation of aluminosilicate ions takes place at 373-393K, and the amorphous aluminosilicate is deposit on the unreacted fly ash(Fig.1(c)). The crystallization of NaP already begins to occur at 393K and the surface is covered with fine zeolite crystals for 24h(Fig.1(d))."

Jan 1, 2003