Search Documents

By O. L. Kachor, A. V. Bogdanov

"In 2015 in the frames of federal special-purpose program «National system of chemical and biosafety of Russian Federation (2009-2014)» Federal State Budget Educational Institution of Higher Education ""Irkutsk National Research Technical University” (further–INRTU) performed works aimed at disposal of accumulated arsenical residues at industrial site of the former Angarsk arsenical plant (AAP) processing arsenious ores from Svirsk town in Irkutsk region. The plant in 1934-1949 produced arsenic trioxide for the defence industry. Prior to starting the works on disposal of industrial pollution focus the total amount of cinders stored on 13 ha of industrial site of AAP was 156 900 tons with 1% average arsenic content. Close to the cinders there were also remains of industrial buildings and process equipment in the amount of 6 600 m3 that contained 150 tons of arsenic. Additional source of pollution at the industrial site of AAP is contaminated soil amounted to 48 000 tons. Proven reserves of gold and silver in the cinders were 6.1 and 47 g/t respectively. In 2015 the source of arsenious pollution was detoxificated according to mineral matrix technology and stored in a special landfill with separate stocking of gold-containing cinder and other arsenious residues. This technology of waste disposal specifies extraction of valuable metals from cinder in future. The similar case is with Vershino-Darasunsky settlement in Trans-Baikal Territory where the abandoned industrial site of the former arsenic plant is located in the central part of the settlement. The concentration of arsenic and valuable components can be compared to the concentration at AAP. Since 2016 the demand for removal of such industrial pollution sources is legislated due to amendments in Federal Law No. 7-FZ on environmental protection. It results in a real possibility to remove such dangerous industrial residues deposits as the one located in Vershino-Darasunsky settlement. INTRODUCTION In the frames of federal special-purpose program «National system of chemical and biosafety of Russian Federation (2009-2014)» as well as the Irkutsk region program “Environment protection in Irkutsk region"" for 2006-2015, INRTU performed the works aiming at disposal of accumulated environmental deprivation–arsenical residues from the former Angarsk arsenic plant (further - AAP) (Figure 1) on processing of arsenopyrite ores of Svirsk town in Irkutsk regionThe plant produced arsenic trioxidein 1934-1949."

Jan 1, 2018

By J. X. Zhang, F. S. Niu

"In order to accurately detect whether the collision occurs between particle and bubble in flotation process, a collision detection method of particle and bubble, which based on morphological image processing and Otsu method, is presented. First of all, it utilizes image pre-processing to optimize images, the target area and the background area are segmented by Otsu method. Then, particle and bubble are fitted to a circle combined with the least-square method. It’s convenient to obtain the coordinate information and radius. Finally, the position of all particles is extracted to an image, which achieves the particle tracking and avoids the complexity of the continuous frame image tracking.Experimental analysis shows that the relationship between the two ordinate difference d and the bubble radius r has a certain influence on the collision detection when the dripping particles are close to the bubble, when d>r, the detection accuracy is 92%;When d=1/2r, the detection accuracy is 97%;When d=0, the detection accuracy is 100%. The result indicates that this algorithm can detect the collision between particle and bubble quickly, and the working hours of manual test are saved effectively ,the best position of dripping particles close to the bubble which is taken with a CCD camera should be in the range of the particle and bubble’s ordinate difference less than half of the bubble radius.INTRODUCTIONFlotation is an important technical means to separate useful minerals from ores. The flotation process of ores and materials in the world is treated by flotation technology up to billions of tons every year, so the study of flotation process is particularly important. Raising the collision probability between mineral particles and bubbles in flotation process is one of the key factors to improve flotation separation efficiency[1]. The study indicates that[2-4] the collision probability between particles and bubbles is influenced by many factors, such as particle density, particle size bubble size, etc. The analysis of these influential factors requires a lot of experiments. Therefore, it is of great significance to design an accurate collision detection method for the research of this field."

Jan 1, 2018

By A. Ekrem Yüce, Gülay Bulut, Feridun Boylu, Vecihi Gürkan, Istanbul Technical University, H. MustafaTarkan

"Nickel sulphide ores subjected to this investigation were taken from Orhaneli district where widespread chromite mineralisation can be occurred. Significant amounts of magnetite and chromite have been existed in the ore together with sulphide and oxide type nickel minerals. Ore sample is constituted about 70% magnetite, 15% sulphide minerals, 5% chromite and iron oxides as well as 10% gangue minerals.According to the chemical analysis results, the representative ore sample contains 1.32% Ni, 10.8% SiO2, 78.4% Fe2O3, 1.3 g/t Ag and 1.0 g/t Au. Mineralogical examinations showed that pentlandite (Fe, Ni)9S8, violarite (Ni, Fe)3S4, millerite NiS and asbolane (Co, Ni)MnO2.(OH)2.1-2H2O were the main nickel minerals and magnetite, chromite, chromium spinals, pyrite, pyrhotite, chalcopyrite, cubanite, goethite, hematite, limonite, rutile, chlorite, talc and serpentine group minerals as associated minerals.The aim of this investigation was to produce valuable nickel concentrates by using gravity separation, magnetic separation and flotation methods. As a results of laboratory scale studies, alternative flow sheets for the production of nickel sulphide concentrate were developed. The related experimental results are given in Table 1."

Jan 1, 2003

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisinger

"INTRODUCTIONThe objective of this work was to deport silver into a residue suitable for subsequent extraction without compromising the high base metal extraction during the pressure oxidation.RESULTS AND DISCUSSIONThe complex sulphide from the tailing pond of Cannington mine, Australia, was re-grounded and a bulk concentrate was recovered by flotation. The major economic sulphides are galena and sphalerite. The chemical analyses revealed 17.22% Fe; 4.88% Zn; 8.22% Pb; 9.49% S2- and 422 g/t Ag. The baseline cyanidation yielded 36.60% of silver at high cyanide consumption (24.17 kg/t NaCN). Pressure oxidation at 150°C (in the absence of iodide), followed by cyanidation of the residue yielded 8% silver extraction. Pressure oxidation was carried out at 110-150°C in sulphate media with additions of potassium iodide and the resulting residue was subjected to cyanidation. High recovery of silver was achieved because its incorporation into lead-hydronium jarosite during the pressure oxidation was minimised, while its deportment into the cyanide-soluble silver iodide was favoured (Figure 1). Silver recovery decreased slightly at high temperatures (140° and 150°C) because of the enhanced stability and kinetics of leadhydronium jarosite, but this could be overcome by increasing acidity and iodide concentration of the slurry."

Jan 1, 2003

By G. P. Wong

"The Inco Matte Separation process was the first commercial application using mineral processing techniques to separate nickel from copper from a slow-cooled matte in Sudbury since 1945. In Inco Sudbury operations, bulk sulphide concentrate containing chalcopyrite, pentlandite, pyrrhotite and some gangue minerals is flash smelted and converted to Bessemer matte. During the controlled slow-cooling of the Bessemer matte, discrete mineral grains of new mineral phases are formed: copper sulfide precipitates as chalcocite (Cu2S), nickel sulfide as heazlewoodite (Ni3S2) and a Cu-Ni-Fe alloy is also formed. Flotation is employed to separate Cc from Hz under high lime conditions (pH>12) with diphenyl guanidine (DPG) as both collector and frother.A simplified matte separation flowsheet is as follows. After grinding, the Cu-Ni-Fe alloy is removed by magnetic separation. All precious metals are recovered in the metallic alloy. Following the rougher flotation, a Cu concentrate is produced after cleaner and re-cleaner flotation in mechanical and column cells. Two Ni concentrates are produced: a high-grade Ni product containing less than 0.8% Cu from the scavenger column tails and a low-grade Ni product containing 5% Cu from the middlings circuit tails. A stream containing the inseparable Cc and Hz from the middlings circuit is generated and recycled back to the smelter. The quantity of this stream is typically about 3% of total feed and can be as high as 5%, greatly decreasing the overall matte separation efficiency. The large mass of the recycle stream is a direct result of poor Cc/Hz separation selectivity in the middlings circuit. The middlings circuit, consisting of a thickener, a regrind mill and two columns, processes two streams: cleaner tailings and scavenger concentrates. The thickener contributes significantly to oxidation due to the long residence time of the pulp in this unit."

Jan 1, 2003

By Yimin Zhu, Dezhou Wei, Haijun Liang, Zhifu Zhou

Pyrite is one of sulfide minerals most widely distributed in the earth. During the flotating separation of metal sulfide and the floating desulfation of coal, it is often requaired to restrain pyrite. However, the result is not very satisfactory because of the little difference of floatability of minerals to be separated. The problem is extremely outstanding for the floating desulfation of coal. Researchers carried out a number of experiments with T. ferrooxidans (Yang et al, 2001; Zhou et al, 2000; Zhou et al, 2001; Wei et al, 2001) for an enhanced restraint to pyrite. The results showed that the T. ferrooxidans after being cultured works the best in restraining pyrite. After 10 min pretreatment, the removal rate of pyrite from coal is up to 80%~90%. The research results by Yuan Xin et al (Yuan et al, 2000) show that T. ferrooxidans can restrain effectively the floatability of pyrite and can reduce the recovery of pyrite from 95% to 8%. Though the restraining properties of T. ferrooxidans to pyrite have been proved by many tests and experiments, there are very limited reports on its restraining mechanism. Thus, a systematic experimental research is carried out in this paper.

Jan 1, 2003

By M. E. Ramírez

In this research bioleaching or extraction of iron present in a kaolin from La Virgen mine, Anti-oquia/Colombia, was carried out. Organic acids produced in SF with Aspergillus niger were used in the process. The fermentation process was carried out in 3 L aerobic stirred bioreactors, at a temperature of 30 °C, a stirrerd speed of 700 rpm, an initial pH of 4 and a fermentation time variable between one to 8 days, obtaining broth fermentation samples daily per bioreactor. For iron extraction, fermented broth from second to sixth day of fermentation was evaluated and it was found that the fermentation broth of the third day showed a larger potential for iron removal, 786 ppm, by using kaolin with an initial iron content of 1401 ppm. A set of tests using commercial organics acids such as citric acid and oxalic were carried out because those were found in the fermentation broth and it was found that oxalic acid presented three times more iron removal than citric acid.

Jan 1, 2014

By Z. T. Yuan, S. L. Qi, Q. Y. Meng, G. X. Zou, L. X. Li, J. W. Lu

"The selective separation of pentlandite from serpentine was investigated using the magnetic coating-magnetic separation by conditioning slurry pH value, stirring speed, magnetic field intensity and controlling dosages of sodium hexametaphosphate (SHMP) and sodium oleate (SO). The optimal conditions were obtained as follows: the natural pH of 6.8-7.2, stirring speed of 2300 rpm, magnetic field intensity of 200 kA m-1, SHMP of 60 mg L-1, and SO of 400 mg L-1. Results showed that the Ni grade was 21.4% with the Ni recovery of 81.4% and MgO content of 3.8%. FTIR indicated that coagulant of SO preferentially adsorbed onto pentlandite and magnetite particles while hardly adsorbing onto serpentine particles when dispersant of SHMP was used. Thus, the selective magnetic coating of magnetite on pentlandite surfaces could be formed due to the formation of hydrophobic surfaces on pentlandite and magnetite particles. Calculations of DLVO (Derjaguin-Landau-Verwey-Overbeek) confirmed that interactions between magnetite and pentlandite particles were much stronger than that between magnetite and serpentine due to the existence of hydrophobic interactions with the addition of SO. Consequently, the pentlandite was successfully separated from serpentine. Therefore, this study exhibits the potential to separate pentlandite from serpentine minerals for practical applications and thus deserves further study.INTRODUCTION It has been well known that the separation of pentlandite from serpentine is a worldwide challenging issue in the processing of sulphide nickel-copper ores. Because the serpentine mainly causes the high pulp viscosity and slime coating on the pentlandite, which interferes with the flotation process of pentlandite (Cao et al., 2016; Feng et al., 2012). The fibrous mineral of serpentine preferentially attaches to the air bubble, forming bubble-macrofibers aggregates, which are easily floated into the nickel concentrates, resulting in the decline of Ni grade (Alvarez-Silva et al., 2016; Kusuma et al., 2014). In addition, the serpentine adheres to the pentlandite as hetero-aggregation or slime coating via the electrical interaction between a positively charged serpentine and a negatively charged pentlandite, which decreases the hydrophobicity of pentlandite and reduces the collector adsorption (Feng et al., 2013). In other words, the presence of serpentine or the occurrence of aggregates (including slime coating and bubble-macrofibers aggregates) seriously affects the flotation process and deteriorates the flotation of pentlandite. Therefore, we propose magnetic separation to recover pentlandite from serpentine with the magnetic coating technology, which is different from forth flotation."

Jan 1, 2018

By Mohammad Mainul Hoque, Linhan Ge, Ai Wang, Geoffrey Evans, Subhasish Mitra

"Dispersed phase interactions involving bubbles and particles in the turbulent environment play a significant role in the flotation process. The conventional collision models only account for the deterministic rather than the stochastic behavior of turbulenct flow. What the bubble-particle collisions would be like remains an open problem due to the complex nature of turbulent flow. To address this research question, the present study aims to quantify the bubble-particle collision efficiency incorporating turbulence using the computational method. Multiple solid particles were released to interact with a single stationary rigid bubble (non-deformable interface). Effect of particles Stokes number, turbulent intensity (TI) and integral length scale on the bubble-particle collision efficiency (Pc) was examined. Large Eddy Simulation method (LES) was used to compute the continuous phase. Fluctuating velocity required at the inlet boundary condition was derived from Gaussian energy spectrum to generate the upstream turbulence. Discrete Phase Model (DPM) is used to simulate particle trajectory. The characteristics of turbulent flow were analyzed through Energy spectrum and energy dissipation rate. The critical initial releasing radius of the annulus, where Pc equals zero, reaches up to 1.5(Rb+Rp) under high turbulent intensity (TI) 20.48% compared to 0.23(Rb+Rp) calculated from the traditional Pc model. Pc decreases as the distance of initial releasing annulus between bubble centre increases. Pc increases as particle Stokes number increase up to 0.66. The collision efficiency for particles of St less than 0.38 is higher under TI 11.78% compared to TI 4%.INTRODUCTION To increase mineral recovery, interactions between bubbles and particles are essential. All flotation devices achieve it through introducing some level of turbulence into the system by increasing specific energy dissipation rate. Figure 1 shows three different flotation equipment, traditional floatation cell, Concorde cell and cyclonic-static micro-bubble flotation column (FCSMC), with different turbulence generation mechanisms – impeller, down-flow liquid jet and pump recirculation, respectively."

Jan 1, 2018

By W. Z. Zu

In proved reserves of vanadium-containing titanomagnetite in Panxi, China, iron grades of ores were 50% ~ 15%. China?s metallurgical industry departments defined the iron ores containing 50% ~ 20% TFe as exploitable resources and the extreme lean iron ores containing 20% ~ 15% TFe as temporary unexploitable resources, the extreme lean ores were as waste rejected into waste dump in mining process. This paper researched process mineralogy of the extreme lean ores, adopted mineral processing technology responded to the properties of the ores to treat the ores and obtained quality vanadium-iron concentrate, titanium concentrate and sulfur concentrate, therefore successfully utilized the extreme lean ores, changed the ores from waste resources to exploitable resources.

Jan 1, 2014

By M. Brennan, A. Majumder

"The mineral processing research community has devoted enormous efforts to the modelling of mineral separators over the last 50 years. While many efforts have been made to use only fundamental physics as a basis for the models, fluid flow patterns in separators are not simple while the motion of particle swarms through fluids is extremely complex.Sluices are the simplest forms of the flowing film concentrators and have been used in the mineral industry since at least the 15th century (Agricola, 1556). Flowing film concentrators, in general, still have widespread applications in the mineral industry and their designs vary according to the specific need.Particle separation in a sluice appears deceptively simple, but the separation mechanism has proven complex and difficult to quantify. Separation in the sluice takes place in a flowing film a few millimetres thick. The particles are suspended by turbulent eddies and motion relative to the fluid takes place in socalled hindered settling mode. The difficulty arises because the presence of the particles influences the flow pattern and when the particles are fully transported by the flow, the flowing slurry may not have the same viscosity as water and does not have the same density. For this reason a universal theory which can explain the behaviour of a suspension in a sluice or any other gravity equipment has still not been developed. Few attempts have been made to analyse the mechanisms involved in the concentrating processes of pinched sluices and Reichert cones.Fluid flow behaviour and slurry transportation characteristics in open channels have, however, been active research topics in the disciplines of fluid mechanics, chemical engineering and civil engineering for many years. As a result, an extensive literature is available, which has led to the development of the model described in this paper.In an effort to test the extent to which fundamental fluid mechanics can provide a prediction of particle separation, a study on a simple parallel-sided sluice has been carried out using glass beads at various particle concentrations and flow rates, and the actual particle separation taking place compared to predictions from modelling.The modelling strategy was divided into two parts; the first was to predict the horizontal slurry flow velocity profile and the second to predict the solid particle concentration over the depth of the flow at different flow conditions. The predictions were then validated with measured data sets. This can easily be done if the slurry flow is split at different fractional flow depths so that the mass flow of solids over different flow heights is measured accurately over a fixed period. Mass flow splits can then be calculated by integrating the product of the predicted slurry velocity profile and the predicted solids concentration profiles from the base of the sluice bed to the slurry free surface."

Jan 1, 2003

By Kazutoshi Haga, Atsushi Shibayama, Altansukh Batnasan

The objectives of this study were to propose a viable alternative method for recovery of precious metals such as gold (Au), silver (Ag) and palladium (Pd) from waste printed circuit boards (WPCBs) and to regenerate the spent lixiviant solution for reuse. The proposed method generally consists of several steps as follows: 1). iodine-iodide leaching for metals extraction; 2). separation and recovery of precious metals and metal impurities from a pregnant leach solution; 3). regeneration of the spent iodine-iodide solution/lixiviant. In this method, more than 99% of Au leaching was achieved in the iodine-iodide solution from the solid residue of WPCBs that was obtained via sequential processes including incineration at 800 ?C and high pressure oxidative leaching with a diluted sulfuric acid at 120 ?C, while the leaching of Ag and Pd was less than 1%, respectively. Besides Ca, Cu, Ni, Co and Zn as main metal impurities, leaching efficiency of other metals did not exceed 1%. The precious metals and base metals as metal impurities present in the pregnant leach solution were separated and recovered by precipitation using L-AA and NaOH solutions. About 99.8% Au, 81.7% Ag and 72.8% Pd were recovered from the pregnant solution at pH of 2 with the addition of 0.1 M L-AA as precipitating agent. The remained small amounts of precious metals and metal impurities were precipitated at pH 13 using 1 M NaOH. The spent lixiviant after sequential precipitation was regenerated in the presence of hydrogen peroxide, hydrochloric acid and potassium iodide. It was revealed that over 90% of gold could be extracted from the residue of WPCBs with the regenerated lixiviant solution.

Jan 1, 2018

By N. Panteleeva, E. Konoplev, I. Michailova, S. Titkov, T. Gurkova, T. Chumakova, Sylvinit Co.

"INTRODUCTIONFlotation of mineral particles by cationic surfactants – namely alkyl amines and their derivatives – is finding ever growing application in processing of various ores and in quality refinement of the benefication end products, iron concentrates for example. In the recent years application of cationic collectors - alkylmorpholines - enabled the development of new highly efficient procedure of water-soluble mineral processing, being also the one with low energy consumption. This procedure is a reverse flotation of carnallite from bay salts of salt-pans and from carnallite ores.The efficiency of cationic SAS influence depends upon colloid-chemical state of the collector in flotation liquid phase, especially if the latter comprises mineral salts. Availability of clayey impurities or slime particles of iron oxide in cation flotation feed, which actively sorb the cationic collector, deteriorate considerably the cation flotation performances. In Halurgy Institute the investigations of cation flotation under potash and carnallite ore processing have been carried out, and new reagent modes, enhancing cationic surfactants sorption at mineral particles, have been developed. Application of new reagents enables one to decrease considerably the consumption of expensive cationic collectors and to enhance the floatability of coarse mineral particles."

Jan 1, 2003

By Buks Kruger

"After the milling and flotation of the platinum bearing ore, the flotation concentrate is electrically smelted in 6-in-line electric arc furnaces and the resulting furnace matte treated in Peirce Smith converters to remove the iron sulphide. The iron free (less than 1% Fe) converter matte is then granulated and sent to the Base Metals- and Precious Metals Refineries for further processing.During the smelting and converting processes two distinct gas streams are produced.The Peirce Smith converter off gas contains 4% - 9% SO2 which is treated in a conventional Sulphuric Acid Plant to produce sulphuric acid (H2SO4).The electric furnace off gas contains 0.9% SO2 and was (until September 2002) vented through a 91 meter high stack to atmosphere.Off gasses which contain less than 3% SO2 is difficult to handle and quite a few processes had been developed over the years to cope with this gas. A broad spectrum of process suppliers and technology approaches is available and the different technologies can be divided into a few main approaches i.e.Scrubbing of the off gas with an alkaline solution to produce an environmentally friendly and stable waste product which can be discharged onto a tailings dam or permanent landfill site.Physical absorption of the SO2 into a chemical solution to produce high quality chemically pure process chemicals.Catalytic reaction of SO2 with O2 to produce SO3 which is absorbed in water to produce sulphuric acid of less than 90% strength.In October 2002 Impala Platinum commissioned a Sulfacid Plant at its Smelter in Rustenburg which recovers the SO2 from the electric furnace off gasses into a weak sulphuric acid solution.The Sulfacid Plant technology is widely used in the paint pigment industry. This is, however, the first application of the technology on electric furnace off gas.The furnace off gasses contains flue dust which is removed in electrostatic precipitators. The gas exiting the precipitators normally still contains between 40 mg/Nm3 and 60 mg/Nm3 dust and passes through a quench-scrubber before entering the reactors. The quench-scrubber cools the electric furnace offgas down from ± 200 °C to 60 °C and act as a final dust removal stage."

Jan 1, 2003

By S. A. Vorobyev, Yu. L. Mikhlin, Ye. V. Tomashevich, A. A. Karacharov, M. N. Likhatski1, A. S. Romanchenko, S. V. Saikova

"A set of state-of-the-art methods have been applied to study ultrafine particles and nanoscale species arising on mineral surfaces upon milling, interaction with flotation reagents, and leaching of base metal sulfide ores in order to gain insights into interfacial mechanisms. The fine fractions produced by ball milling of a Pb-Zn Gorevsky ore and four Cu-Ni sulfide ores studied with laser diffraction, dynamic light scattering, zeta-potential measurement, Xray photoelectron spectroscopy (XPS), SEM, TEM and other techniques. The particle size distributions had, aside from the peaks at 20-60 ?m, maxima near 1-2 ?m; the flotation was considerably suppressed when the yield of positively charged ultrafine particles approached tenths % (several kg per ton). High-energy XPS and X-ray absorption spectra revealed that sulfide minerals depleted in metal in air and aqueous solutions were composed of outer “polysulfide” layers, strata with disulfide species, and heavily defective underlayers, and “passivation” was explained by stability of the metal-deficit structures. Dixanthogen at pyrite and copper-activated sphalerite, dixanthogen and then cuprous xanthate on chalcopyrite, and chemisorbed xanthate at galena were specified as the main interfacial products using cryo-XPS of fast-frozen flotation slurries. The particle size, zeta-potential and behavior of colloids of Cu and Pb xanthates and dixanthogens were largely determined by the initial ratio of a cation and collector; the properties of copper xanthate nanoparticles were also affected by incorporated dixanthogen (about 15 wt.%). Submicrometer gas domains of 3-8 nm in height and “hydrophobic” forces upon the probe retraction were found on xanthate-treated minerals using atomic force microscopy and spectroscopy; their impact on flotation is briefly discussed.INTRODUCTIONInterfacial phenomena play a key role in flotation, leaching, water purification and related environmental processes. The mineral processing and extraction of metal from sulfide ores commonly involves milling the ore, which produces, along with the particles of 20 µm to 100 µm, mineral entities ranging from micrometer to submicrometer and nanometer scale. Furthermore, ultrafine particles of flotation reagents, products of metal sulfide oxidation, and so on may form spontaneously and accumulate in production water, flotation froth, deposit on mineral surfaces, affecting the flotation performance, and then enter waste waters, mine and natural drainage, polluting soils, surface- and ground waters (Miettinen et al., 2010; Wang et al., 2014). The efficiency of flotation and hydrometallurgical recovery of values, environmental issues are crucially dependent on the state of mineral surfaces. Particularly, it is generally accepted that the surface non-stoichiometry of sulfide minerals induced by oxidation and leaching should affect their hydrophobicity and reactivity, including so-called “passivation”, but the nature of such surface layers are still a matter of controversy (see, for example, Holmes and Crundwell, 2013). Another phenomenon attracting rapidly growing interest in several areas is low-dimensional gas species (“nanobubbles”) at hydrophobic surfaces that may play a decisive role in particle-bubble attachment in flotation but remains scarcely investigated up to now (Xing et al., 2017). Here, we survey our recent results on the abovementioned problems applying a series of rather new methods and approaches; more details can be found in refs. Karacharov et al., 2016; Mikhlin et al., 2015; 2016; 2016a; 2016b; 2016c; 2016d; 2017; 2017a; Vorobyev et al., 2017."

Jan 1, 2018

By João Queiroz, Cristian Marquez-Sarmiento, Luiz Teixeira

The removal of various metals from process waters and effluents is usually done by precipitation of the corresponding hydroxide. Manganese however is one metal that does not respond efficiently to that approach. It may be seen in its eH X pH diagram that the way of oxidation to Mn IV rather than hydrolytic precipitation of the Mn II ion as its hydroxide, is the way to efficient precipitation of Mn in the pH range 6 to 10. We studied the use of oxidants O2; NaClO; H2O2; Caro´s Acid (H2SO5) and the combinations of O2 or H2O2 with Na2S2O5, and H2O2 with NaClO, for the oxidative precipitation of Mn from synthetic solutions starting with 10 mg/L Mn, at 25 oC. In adequate conditions, which include pH > 8, it is possible to reach final [Mn] less than 0.1 mg/L in 60 minutes of reaction time.

Jan 1, 2014

By A. N. Zagorodnyaya, T. N. Bukurov, Z. S. Abisheva, A. S. Sharipova

"This work presents the results of the development of a flowchart for the processing of copper production dusts resulting in the production of of lead sulphate, tribasic lead sulfate (TBLS), ammonium perrhenate, zinc, copper-cadmium cake.Dust having the following composition (wt. %): Pb 39.3, Zn 6.5, Cu 5.5, Stotal 10.8, As 1.05, SiO2 0.6, Cd 0.8, Bi 0.04, Ag 0.02, Re 0.03 was used in the work. Chemical and X-ray analyses indicated that lead, zinc and copper are generally present in dusts in the form of sulfates, various amounts of oxides, sulfides, silicates; sulfur (according to chemical analysis data) is present in the form of sulfates (~ 90%) and in the form of sulfides (~ 10%).Studies have been made on two-stage stripping of copper production dusts containing lead, zinc, copper, cadmium, rhenium in the form of various compounds, at first with soda solution, then with nitric acid solution. It has been indicated that the combination of the operations allows the recovery of 98% rhenium, 82% lead, 92% copper, and 96% zinc and cadmium each in the solution. Furthermore, at the stage of dust leaching with soda, 80% of rhenium and 0.01% of nonferrous metals each are recovered in the solution. Remaining quantities of all metals are recovered in nitric acid solution up to maximum values. Such behaviour of metals is caused by metal phase content in dusts and properties being formed during leaching of compounds. At the stage of dust leaching with soda solutions, carbonates with various compositions are formed due to the exchange reaction between nonferrous metal sulfates and sodium carbonate. The conversion of PbSO4 into PbCO3 is apparently occurs in the solid phase and the conversion of readily watersoluble zinc, copper, and cadmium sulfates into that of carbonate salts occurs in the liquid phase. Rhenium passes into solution due to the presence of rhenium greater quantity in dust in the form of readily soluble perrhenate. Some portion of the perrhenate is, probable, blocked by lead sulfate and liberated in the conversion of PbSO4 into PbCO3."

Jan 1, 2003

By Weiguo Xie, Malcolm Powell, Lian Liu, Ping Yu

"In order to develop a common mathematical and simulation platform for tumbling mills, a review of existing mechanistic models was made identifying the key aspects of grinding and slurry transport which are common to all tumbling mills. A mill model structure has been developed for all types of tumbling mills based on the population balance framework by incorporating breakage characteristics, slurry and solids transport, product classification and discharge, and energy consumption. A size-dependant breakage model developed by the JKMRC is applied. Transport is separated from breakage events and treated as a main sub-model in the new model structure. The model structure is based on dynamic time-stepping technique to enable dynamic simulation capability for non-steady-state simulation and control modelling. It is envisaged that the new model will cover a full range of milling conditions. It should enable a smooth transition between different mill types, such as from AG (Autogenous Grinding) to SAG to ball mill. The dynamic mill model structure developed here is the first step towards mechanistic modelling of grinding mills and provides great potential for the optimization of the comminution process."

Jan 1, 2014

By Yizhong Yuan, Dao Li, Nannan Xue, Tao Liu, Yimin Zhang

A new multi-stage counter-current circulation leaching process for extracting vanadium from stone coal was proposed, and the main factors on multi-stage counter-current circulation acid leaching process were investigated. The results show that the vanadium recovery could reach 86% under the conditions of sulfuric acid concentration of 4 M, liquid to solid ratio of 2 mL/g, temperature of 95 °C, reaction time of 60 min, mean particle size of 125 µm and circulation acid leaching stage of three. The losses of vanadium in acid leaching solution appeared during the four-stage acid leaching process. The strong adsorption performance of new formed KAl(SO4)2(H2O)12 crystal was main reason.

Jan 1, 2014

By Robert Dunne

A review of the current ?state of the art? of refractory gold treatment will be provided. This will include a global perspective of the refractory processes that are being practiced, where they are and some discussion on why the processes were selected. Some discussion on the challenges that face the refractory gold industry will also be provided.

Sep 1, 2012