Search Documents

By L. McFarlane, D. Rollwagen

"Madawaska Mines produces a uranium precipitate (83-85% u3o8) using a magnesium oxide slurry to precipitate the uranium from solution. The solution, at approximately 9""0 g/l u3o8 is neutralized to a pH of 7.0. At the Eldorado Nuclear Refinery in Port Hope, the precipitate is not acceptable as a single feed to the refinery process. It was discovered that a 2% silica impurity caused emulsion problems in the solvent extraction column.After extensive studies of possible solutions, such as two-stage precipitation and solvent extraction, an acceptable solution was found. The selective precipitation of uranium at a pH of 3.5-4.0 using Hydrogen Peroxide produces an almost silica free product of higher purity (90-93% u3o8) to that of straight magnesium oxide precipitation. Introduction Madawaska Mines Limited is located four miles southwest of Bancroft, Ontario. The annual production of u3o8 is approximately 610,000 pounds. To produce the final product or yellowcake, nine separate steps are required. These are (1) grinding, (2) dewatering, (3) leaching, (4) acid filtration, (5) clarification, (6) ion exchange, (7) precipitation, (8) washing, and (9) drying and packaging. To illustrate these steps, a complete flowsheet of the mill is displayed on page three.The yellowcake is sent to Eldorado Nuclear Limited in Port Hope, Ontario for further concentrating and refining. As part of their routine specification check, a test called the amenability test is performed. This test indicates how a particular dissolved yellowcake product reacts to solvent extraction. The Madawaska yellowcake did not pass the test."

Jan 1, 1982

By K. Halada

Current trend of the global flow of strategic metals are analyzed to discuss the strategy of the development of recycling technology and alternative technology. In many cases, each global flow of metal is changing from the trilateral structure of U.S., EU and Japan in the later 20th century into the convergence to China as the factory of the world. Scrap flows are also changing dynamically. A long term change of prices of metal has gotten changed since the entrance of this century. The estimation of metal consumption up to 2050, in which the author estimated that many kinds of metal will overshoot the reserve base line, is revised considering these change of current trends.

Jan 1, 2014

By Kazutoshi Haga, Ariunbolor Narankhuu, Ariuntuya Battsengel, Yasushi Watanabe, Altansukh Batnasan, Akita University

"Rare earth minerals are usually concentrated by flotation, magnetic or gravity separation methods to produce concentrates that are subsequently leached with hydrochloric (HCl), sulfuric acid (H2SO4) or nitric acid (HNO3). About 75 % REEs are lost in gypsum by-product when apatite is dissolved in H2SO4, whereas more than 80% of REE can be extracted from the apatite using HCl and HNO3 leaching processes, respectively. Therefore, the main aim of this study was to find an efficient process of dissolution of rare earth elements (REEs) from apatite ore by sulfuric acid solution due to its lower cost. In order to optimize the dissolution process, effects of different parameters, namely, concentration of H2SO4 (0.05 – 6 M), solid/liquid phase ratio (1:50 – 1:100), temperature (20 – 80 ºC), agitation speed (300 – 900 rpm), and leaching time (0.5 - 6 h) on the dissolution of REEs from apatite ore were examined in various intervals. The contents of main REEs in the apatite ore used in this study were (as % wt): 3 % La, 6 % Ce, 0.6 % Pr, 2.1 % Nd, 0.2 % Sm and 0.3 % Y. X-ray diffraction (XRD) analysis identified fluorapatite and phlogopite as main minerals in the ore. The results obtained from leaching experiments showed that more than 85% of REEs were dissolved from the apatite ore under the optimized conditions, which were: 1 M H2SO4, particle size of -150 + 100 µm, S:L phase ratio of 1:50, agitation speed of 500 rpm at 20 ºC for 1h. The XRD analysis revealed that main mineral compositions of the residues from 1M and 6 M H2SO4 leaching are gypsum (CaSO42H2O) and hemigypsum (CaSO40.5H2O), respectively.INTRODUCTIONThe term rare earth elements (REEs) denote the group of 17 chemically similar metallic elements consisting of the 15 lanthanides, plus yttrium (Y) and scandium (Sc) in the periodic table. These metallic elements are generally divided into two sub-groups; (1) the cerium sub-group, which is called “light rare earth elements” (LREEs), includes the elements from lanthanum (La) to europium (Eu), and (2) the yttrium (Y) sub-group elements, which are known as “heavy rare earth elements” (HREEs), are the remaining lanthanides from gadolinium (Gd) to lutetium (Lu) plus yttrium (Gupta and Krishnamurthy, 2005). The REEs occur together in the minerals due to their chemical and physical similarities, which cause problems of separating them from one another (Abreu and Morais, 2014). Although REEs are relatively abundant in the earth’s crust, they are typically dispersed and rarely occur in concentrated forms, making them economically challenging to obtain. There are a wide variety of rare earth minerals, however economic deposits of REEs in mining are bastnasite (La, Ce) FCO3, monazite (Ce, La, Y, Th) PO4, and xenotime YPO4 (Binnemans, 2013; Xie, et al, 2014). Due to the unique physical, chemical, catalytic, electrical, magnetic and optical properties of REEs, demand of these elements has increased dramatically with the advent of new technologies in electronics, communication, construction, energy and medicine (Jordens, et al, 2013). Since 1990, China has provided about 90 % of REEs worldwide. Japan and United States are the largest consumers of China’s REEs. In 2010, China announced to reduce REEs exports to Japan, as it tended to increase prices of REEs and to reduce a stable supply of REEs in the world market (Humphries, 2013). Therefore, there has been an increase in recent exploration activities intended to reveal new commercial sources of REEs and to bring them into production (Antico, et al, 1996). Apatite is an important host mineral for REEs in igneous and metamorphic rocks and can be used as an ore for those metals (Kanazawa and Kamitani, 2006). Apatite is also the main source of phosphate fertilizers and phosphoric acid (Habashi, 2013; Emsbo, 2015)."

Jan 1, 2016

By Charlie Harper

Open Pit Mining of Golden Band Resources? EP Gold Deposit Golden Band Resources Inc. (GBN:TSX-V) is Saskatchewan's newest Gold Producer. Located in the La Ronge Gold Belt of northern Saskatchewan, GBN has over 875 km2 of claims with 12 known gold deposits and 4 former producing mines. Production has begun at the Roy Lloyd Mine (Bingo Deposit), to be followed initially by our EP and Komis properties. Development of the underground infrastructure at the Roy Lloyd Mineis continuing and on schedule. Production from these deposits will feed our centrally located and 100% owned Jolu mill. We have our provincial environmental permits in place, and we have an established infrastructure including a 400 tonne-per-day mill, year-round road access, and access to grid power. Construction of the grid power line and the above ground tailings facility are now complete.

Nov 1, 2011

By Helen Shang, Jianjun He

In nickel and copper production, sulfur dioxide (SO2) is generated during mineral smelting. Emission of sulfur dioxide into the atmosphere causes serious health and environment issues. Sulfuric acid plants, which convert the harmful SO2 gas to commercially useful sulfuric acid product, ensures safe and environmentally sound smelter operations. The sulfuric acid plant is mainly composed of a SO2 to SO3 converter, a series of heat exchangers and SO3 absorption towers. The SO2 converter is crucial for minimizing SO2 emission in a smelter. In this paper, steady state and dynamic modelling are carried out for the converter using mole and energy conservations. Simulations are performed to investigate the effect of feed conditions on SO2 conversion. The developed model represents an important component for modelling the acid plant in a smelter and is expected to provide a fundamental tool for the future optimization and control development.

Jan 1, 2014

By A. Himsley, E. Byleveld

"With reference to the chemical constraints underlying the ion exchange process for uranium recovery, a generalized view is presented on the actual and the achievable efficiency of the process. The area considered is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution.A comparison between actual plant results and the chemical requirements shows that:(a) Unless new and better ion exchange resins are developed, no dramatic change in equipment size and resin inventory is""anticipated. (b) Elution efficiency, especially for sulphuric acid, may be improved considerably. More concentrated eluates may beproduced at lower chemical consumption. A possibility of achieving additional purification solely by ion exchange is discussed.IntroductionThis paper presents a generalized view of the actual and the achievable efficiency of the ion exchange processes for urannium recovery. The study is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution. The ultimate efficiency attainable with ion exchange is dietacted by the chemical reactions underlying the process. The most sophisticated technology cannot change the diffusion rates in the ion exchange resin nor make the uranium loading exceed its equilibrium valueThe design of an ion exchange plant for uranium recovery involves a considerable number of parameters as a result of the wide variety of pregnant solutions produced from different orebodies. Therefore, a generalized approach of the ion exchange process inevitably neglects some parameters which maylead to significant variations in apparently identical situations.The uranium concentration in the pregnant solution, together with its pH, are the principal variables which determine resin loading and residence rime in the ion exchange system. On the elution side, the type of eluant and its concentration will determine the contact time required and the amount of eluant needed to strip the resin. The temperature, the properties of the ion exchange resin, the total dissolved solids in the feed solution and the competing ions are other variables that affect the chemical performance; these, however, may be considered as a correction of the principal parameters if one is interested only in general trends."

Jan 1, 1980

By K. Kryst, K. Elkayar

The increasing need to process lower grade contaminated copper concentrates and simultaneously produce higher purity copper cathodes necessitates a more diligent control in the electrorefining process. Ion exchange processes can be a powerful tool in controlling electrolyte impurities to ensure trouble free operation within the tankhouse and to help maintain cathode purity. In addition, some impurities can be recovered as a value added product. The use of a short bed ion exchange process provides a unique opportunity for impurity management in copper refineries. Several metals are discussed in this paper, including Sb, Bi, As and Ni and their methods of control and recovery within the copper electrolyte circuit. INTRODUCTION To produce a high purity copper product by electro-refining a copper electrolyte, it is important to control the concentration of impurities such as arsenic (As), bismuth (Bi), antimony (Sb), and nickel (Ni). These impurities are introduced into the electrolyte from the copper anode and can affect the copper product and the production operation. The presence of As in the copper product results in a lower electric conductivity and reduced workability of the copper. High levels of Bi in the electrolyte will result in a copper cathode product containing Bi. High Sb concentration will cause undesired floating slimes. A variety of methods have been developed to control the level of these impurities in the copper electrolyte including precipitation, liquid extraction, and ion exchange. These impurities can be recovered and used. This paper discusses novel methods that utilize short bed ion exchange technology to control these impurities. Also, the use of ion exchange to recover acid from the liberator cells bleed for reuse in the tankhouse is reviewed. SHORT BED ION EXCHANGE Short bed ion exchange technology has been employed extensively in the metal finishing industries for over forty years. Unlike conventional ion exchange, short beds are fixed beds without freeboard space. The application of short bed technology results in significant benefits when compared to conventional ion exchange. The resin used in this technology has a significantly smaller diameter than conventional ion exchange resin. As a result of the smaller resin size, exchange kinetics improves dramatically. This facilitates operation at higher flow rates and the use of smaller beds with a small mass transfer zone length. Smaller beds are especially important for applications that use chelating resins due to the high cost of the resin.

Jan 1, 2019

By H. Lazreg

This paper presents an evaluation of surface resistivity techniques as a tool for delineating salt-water intrusion in Shippegan, N.B. The study consisted of resistivity profiling, resistivity soundings and a limited number of induced polarization soundings in selected areas in the Province of New Brunwick. The results from resistivity profiling indicate that when seawater intrusion occurs in a sandstone formation the resistivity contrast is sufficiently large to allow a precise delineation of the intrusion. A formula is then derived to convert resistivity values to chloride concentration in the "cone of intrusion". The results from resistivity soundings showed that shaly formations may have resistivities as low as seawater-contaminated sandstone. An indeterminacy has resulted from this resistivity overlap. A limited number of IP soundings were performed in an effort to resolve it. The results showed that IP can be of appreciable help in resistivity interpretation.

Jan 1, 1972

By V. G. Papangelakis, G. A. Moldoveanu

"One of the major commercially viable secondary sources of rare earths elements (REE) are the ion-adsorption ores, containing 0.05-0.3 wt% rare earth oxides physically adsorbed on the surface of clay minerals formed during weathering of lanthanide-rich rocks. Although ion-adsorption deposits are substantially lower grade than other types of rare earth sources, this is offset by the easier mining and processing costs and the low content of radioactive elements. The conventional extraction route involves ion exchange leaching with monovalent cation solutions (usually ammonium sulphate) under ambient conditions; during the process, the lanthanides are desorbed and transferred into solution, being replaced by the exchange cation. While ammonium ions are known to perform best, there is increased environmental motivation to investigate alternative lixiviants in order to minimize ammonium sulphate impact via reducing its use without considerable loss in rare earth recovery.The objective of the present research was to screen various cations salts (alkaline and alkalineearth metals present as sulphates, chlorides and acetates, respectively) in order to comparatively evaluate lanthanide desorption levels and provide a theoretical base of the observed behaviour. The overall aim is to gain a better understanding of how both cation and anion may affect the overall REE recovery from ores in order to provide alternative processing routes. The distinct exchange capabilities of cations were explained in terms of differences in cation hydration enthalpy within the same group, i.e. Cs+ > NH4 + > K+ > Na+ > Li+ and Ba2+ > Ca2+ > Mg2+. For the same cation, it was determined that REE extraction efficiency follows the order sulphate > acetate > chloride, based on dissimilarities in constants of formation values. Various process implications scenarios will be described based on using mixed cations and anion matrices."

Jan 1, 2016

By S. A. Briggs

Bioremediation has been accepted as a treatment technique for groundwater contamination in subsurface soils and shows promise for contaminated fractured rock environments. Biological growth in fractured rock is expected to occur predominantly as biofilms attach to the fracture surfaces. Biofilms in rock fractures are subject to a complex system of forces and other phenomenon due to the dynamics of the bulk fluid in which they grow. In this paper, through the applications of computational fluid dynamics (CFD) to rock fractures, where the boundaries are rough and the flow is complex, a precise analysis was conducted of the interaction of a fluid flow and the rock fracture. Specifically, hydraulic parameters and velocity profiles of an actual rock fracture were calculated and compared to a fracture of equivalent aperture. From the analysis it is clear that it is important to use more complex models such as the Lattice Boltzmann Method used is this paper to describe fracture flow.

May 1, 2009

By D. P. Goodall

THE development of the oil and gas resources of Western Canada is not, as many suppose, a new industry. For more than half a century an intensive search for these valuable products of nature extended from near the western edge of the Precambrian Shield to the Pacific coast, and from the International boundary north to the Arctic circle. The chief centre of interest to the oil prospector has, however, always lain in that region lying east of the first range of the Rocky mountains and confined largely within the boundaries of the Province of Alberta. Although there are many geological problems yet to be worked out in this Province, the oil-well driller has helped in no small way in determining sub-surface conditions and distribution of rock formations. The chief geological conditions as they affect the drilling of wells are generally re-cognized, and for this purpose the Province may be partitioned into three main divisions: first, the disturbed belt or foothills region extending along the eastern edge of the Rocky mountains; second, the Alberta geosyncline, a broad trough lying to the east of and parallel to the disturbed belt and from which the formations rise eastward to level off and form, third, the plains ? ? region, extending over the rest of the Province. A relatively small area in the northeastern part of the Province is underlain with Precambrian rocks and may be excluded from this classification, as it is of no interest to the oil prospector. The foothills, or disturbed belt, has presented the greatest difficulty to drilling, though it has produced the largest yield of oil within the Province to date. Within the foothills belt, the rock formations consist largely of hard shales interspersed with layers of abrasive sandstones, which wear out drilling bits at an alarming rate. The strata, in most flaces, dip steeply and are cut by numerous thrust faults. Although some o the faults have great displacements, their presence may easily be overlooked or the extent of the fault misinterpreted. Many a prospect well has been located on what appeared to be a suitable geological structure only to find, after drilling through a normal succession of rocks for 4,000 feet or more, that the drill had passed through a major fault plane to a younger formation than that in which drilling was started. Only a repetition of formations already drilled could be expected at greater depths.

Jan 1, 1942

By O. Espinoza Ortega, S. Song

A process scheme has been devised to improve the silver recovery and the grade of concentrates from the scavenger concentrate of a silver ore flotation circuit. Based on modal analysis studies it was found that silver sulfide minerals in the scavenger concentrate were associated as simple binary particles and finely disseminated in sulfide and non-sulfide gangues. Fine grinding of the concentrate improved the grade-recovery curve of silver to a very limited extent owing to heterocoagulation between liberated fine silver sulfides and coarse particles of gangue. This heterocoagulation phenomenon was prevented by grinding the concentrate in the presence of the dispersing reagent sodium hexametaphosphate. The silver grade-recovery curve was improved by practicing. before the conventional flotation step, a selective aggregation step for the fine silver sulfide particles using the non-polar oil kerosene, the sulthydryl collector Aerophine 3418 and conditioning the pulp under strong agitation conditions.

Jan 1, 2004

By H. Wotruba, L. von Ketelhodt, M. Kowalcyk, C. Kleine, M. Robben

Sensor-based sorting is a financially and technically viable technique that is operating with little or no water and relatively little power consumption. Sensor-based sorting has already proven its operational stability at two gold applications in South Africa. Sensor-based sorting cannot only turn waste dumps and diluted mining blocks into reserves. The implementation can also cause a decrease in specific operating costs of mill and mine when for example replacing selective mining by bulk mining methods with subsequent sorting. Successful installations, operational experience, test work data and flow sheet integration from mine-to-mill underline the impact and potential that sensor-based sorting can have on the gold mining and processing industry.

Jan 1, 2011

By Christopher Andreae

"Years before the present iron and steel works were established at Sydney, several thriving although short-lived iron work s operated in Nova Scotia. These furnaces reflected the general nineteenth-century North American experience with iron work s. At the beginning of the century, small furnaces struggled to supply local needs. Charcoal was the principle fuel and water powered most furnace equipment. By the end of the century, a few huge primary iron and steel work s dominated production for Nova Scotia and the rest of Canada.Two sites achieved prominence in the nineteenth-century Nova Scotia iron industry: Londonderry and Ferrona. Londonderry, the larger and longer-lasting of the two sites, is today a small village on the south flank of the Cobequid Mountains, about 30 km west of Truro. Prior to the establishment of an iron works in 1849, no community existed. At the peak of operation in the 1880s, however, over 2,600 people were located there. The second site, Ferrona, today is a mere crossroads on the map, about 10 km south of New Glasgow. Following the construction of a blast furnace there in 1892, a small village grew up around the furnace, but once the furnace was blown out in 1904, the population gradually drifted away.Early HistoryThe history of Nova Scotia's iron industry began in 1604 when Samuel Champlain became the first European to identify iron ore in the future province. Despite this early acknowledgment, iron was not smelted commercially in Nova Scotia for another two hundred years. Although primitive smelters of the period produced more iron than could be used locally, early settlers depended on imports of iron from Britain and the United States."

Jan 1, 1983

By Roger Davieds

FACT: a company?s profitability (or loss) is directly related to the efficiency and effectiveness of its maintenance operation. Fact: in order to contribute in a positive manner, maintenance must understand what its true purpose is in the organization. It is easy to say our main purpose is to increase: ?equipment uptime ?OEE ?asset life cycle We all understand this; so does management.

May 1, 2010

By Peter Moon

THE mineral industry of Canada relies heavily upon the talent of its technical men. It is vital to the well-being of the industry that its supply of young, trained men be adequate. At the present time, the industry is acquiring only 200 new graduates a year. The shrinking supply is far below present and future requirements. Other industries and research organizations are competing for engineers and scientists. Dr. J. B. Mawdsley (1), Past-President of the Canadian Institute of Mining and Metallurgy, has recently outlined a program designed to attack the problem. Dr. J'. C. Sproule (2), another former President of the Institute, has stated that: "The need for selection of trainee material is commonly recognized, but little is done about it." The following paper contains a short discussion of occupational interests, and outlines research, using psychological knowledge and measuring techniques, aimed at the identification of desirable recruits for the mineral industry.

Jan 1, 1963

By A. Roy, T. LeBel, P. Coursol, P. Lind

At the early stage of a mining project, small amounts of concentrates are available for testwork. For gold concentrate or ores containing significant arsenic levels, batch bench scale roasting is often unreliable, leading to highly variable gold recoveries to be used in the project’s financial justifications. With an appropriate bench scale unit using continuous feeding and residence time control for solid and gas phases, reliable numbers can be obtained at small scale with only a few hundred grams per test condition. This paper describes the development of a pilot fluid bed roasting unit by Kingston Process Metallurgy Inc. (KPM) to perform representative trials on gold concentrates containing arsenopyrite, arsenian pyrite and carbonaceous components. Calcines produced under different conditions were characterised by chemical analysis and electron microprobe; the calcine microstructure obtained is described. The most important parameter affecting gold recovery is oxygen content in the roasting atmosphere, with the lowest controlled oxygen level giving the highest gold recoveries. Higher local temperatures in the bed may cause the formation of molten glassy phases which can also reduce the gold recoveries significantly. The impact of roasting conditions in the two inch fluid bed is compared with commercial results obtained in full scale operation.

Jan 1, 2014

The Bluebell mine of The Consolidated Mining and Smelting Company of Canada Limited extends under Kootenay lake, in southern British Columbia, and water control underground has always been a major problem. This paper gives a brief history of the operation, and then de-scribes the methods used by Cominco to keep the combination of lake seepage, ground water and thermal spring water under control. The pumping arrangements are de-scribed in considerable detail, with illustrations to show the various stages of development, and the power supply sys-tem is outlined.

Jan 1, 1966

By E. O. Lilge

THE USE of the Driessen cone as a heavy-media concentrator involves a mineral dressing process in which many variables inherent in the ore and in the process may have an effect on the efficiency of mineral separation and the operation of the cone. The magnitude of these effects and their possible interrelationships must be known before a full-scale plant can be designed and built. It appears that, among the most important variables, are the following: Ore Variables: The particle size of feed The difference in specific gravity between economic and non-economic minerals The intimacy of mineral association Cone Variables: Cone inlet area Ore to media ratio Cone ratio Size distribution in heavy media Specific gravity of media Viscosity of media Type of media

Jan 1, 1956

By C. Stapel, P. D. Roberts, D. G. Jones, W. G. Macdonald, R. J. De Meijer

"Measurement of natural radioactivity has been used in both a qualitative and a quantitative way in mineral exploration, particularly in the search for uranium. In the last ?ve years, the Kernfysisch Versneller Instituut (KVI) and British Geological Survey (BGS) have designed, built and tested a new detector system that greatly improves quantitative applications in mineral exploration, especially on the sea?oor and in the nearshore zone. The new system is an enhancement of an earlier BGS design. The major improvements comprise the use of a highly sensitive ?-ray detector, together with new data processing, from which concentrations of natural radio nuclides may be deduced in real time. After laboratory analysis of samples, these concentrations can be converted into mineral percentages. Once the mineralogy of an area has been characterized, this conversion can also be done in real time.Thus far the system has mainly been used to map heavy-mineral concentrations in coastal subtidal and intertidal sediments. For such work the multi-sensor detector probe is towed on the sea?oor and various parameters are recorded continuously. The probe contains, in addition to the gamma-ray detector, a water-pressure sensor (giving water depth) and an acoustic device to measure bottom roughness. The system, when used together with high-precision positioning systems such as D-GPS,enables the production of detailed maps of bathymetry, bottom roughness, and sea?oor radioactivity or mineral distribution. These maps allow mineral concentrations to be readily correlated with sea-bed topography and sediment type. In the same way, ?-ray detectors could be used advantageously during dredging operations to provide on-line assessment of the mineral content of the dredged sediment as well as to guide the direction of dredging. Additionally, the same technique could be used to monitor the subsequent fate of a dredge spoil after dumping on the sea?oor.Natural radioactivity arising from potassium and the thorium and uranium decay series has potential use for the fast and reliable assessment of siliciclastic and phosphatic impurities in limestones. Detection of such impurities may preclude the use of the limestone for chemical or cement production.Apart from its use in exploration, the technique has signi?cant potential in mineral processing, particularly of heavy minerals. It can be applied as on-line quality control in dry and wet separation processes and for process control, by using decisions based on the results to control valves and other instrumentation. In addition, it can also be used in environmental monitoring of waste arising from mineral extraction and processing. In conclusion, the technique described has a diversity of applications in exploration, mining and mineral processing."

Jan 1, 1997