Search Documents

By I. E. Puddington, F. W. Meadus

The beneficiation of barite in mill tailings using an agglomeration technique has been demonstrated. Barite was selectively absorbed from a conditioned aqueous slurry into a collector oil by mechanically mixing slurry and oil. The resulting oil-bonded barite-containing agglomerate was washed, to remove gangue material, and further mechanically contacted with dilute H2SO4 This treatment resulted in the transfer of barite into the aqueous phase. Grades as high as '97% BaSO4, with recoveries of 80%, have been obtained using this technique.

Jan 1, 1973

By R. B. Stein

"Countercurrent decantation circuits(CCD) are often employed in hydrometallurgy to effect solids-liquid separation in combination with a barren solution wash to reduce losses of valuable solution component(s) from the tails. Bechtel Corporation uses its BEMSIM flowsheet-modelling PC computer program to simulate a CCD circuit where the ""dirty"" wash solution contains significant amounts of soluble components. An algorithm successfully models this condition and is simplified to a single expression when the wash solution is a ""clean"" solution containing no solubles. The CCD calculation module is compared to operating data from uranium and nickel-cobalt CCD circuits.IntroductionHydrometallurgical process schemes have often relied on countercurrent washing methods to reduce soluble losses of valuable product in the tails. Commonly used equipment to effect this operation is a CCD circuit of N thickeners in series, where a slurry is fed to thickener I and a wash solution to thickener N; clear pregnant solution overflows thickener I and washed tails exit as underflow from thickener N. CCD circuits of this type are typically employed when the solids tend to slime heavily and where a filter is not economic.A typical CCD circuit usually employs from two to five thickeners and can employ either a ""clean"" washing solution of, say, pure water or else the hydrometallurgical circuit may generate a ""dirty"" barren solution containing an appreciable amount of soluble component which may be advantageously returned to the process as CCD wash solution. Various authors have treated the case for clean washing solutions (Svarkovsky 1977, Merritt 1970). For the case of dirty wash solutions, an algorithm has been developed to enable efficient modelling by the BEMSIM computer program, because the need for an accurate method to calculate soluble losses is required when performing an economic trade-off analysis of the value of product lost in the tails as a function of the number of thickeners."

Jan 1, 1990

By S. F. Guo, B. W. Zheng, X. L. Huang, S. W. Qi

"The study of mechanical characteristics of rock discontinuities under different shear deformation velocities is an important premise of rock slope dynamic response analysis. According to disposing and calculating the experimental results of previous research about peak shear strength of rock discontinuities under different shear deformation velocity of constant normal loading, the law of influence of shear velocity on the total friction angle is studied. Based on the research results, it can be found that the total friction angle of rock joint specimens varies in the form of negative logarithm with the variation of shear deformation velocity. It’s also indicated that the total friction angle of rock joints decreases with the increase of shear deformation velocity for rock joints of relative strong homogeneity and isotropy. However, the total friction angle of rock joints increases with the increase of shear deformation velocity for rock joints of relative strong heterogeneity and anisotropy and the latter amplitude of increase is less than the former amplitude of decrease. The physical property and microscopic geometry of rock joints play an important effect on the increase or decrease tendency and amplitude variation of total friction angle with the increase of shear deformation velocity.INTRODUCTIONThe rock slope dynamic response is largely restricted by rock discontinuities. Hence the study of dynamic characteristics of rock discontinuities, especially the dynamic shear characteristics is an important premise of rock slope dynamic response analysis (Qi et al., 2007). Seismic load is both dynamic load and cyclic load (Liu et al., 2011). Under the dynamic and cyclic shearing actions of seismic load, the rock slope which is stable under the condition of static load may slide along the rock discontinuities whose shear strength reduce and then the earthquake landslides occur. The strength degradation and deformation mechanism of rock discontinuities under the dynamic and cyclic shearing actions is one of the key problems to be solved in the work of earthquake prevention and control of engineering slope. Based on the above understanding, predecessors conduct some researches which focus on the shear behavior mechanical characteristics of rock joints under cyclic shearing actions (Plesha, 1987; Hutson & Dowding, 1990; Jing et al., 1992, 1993; Huang et al., 1993; Qiu et al., 1993; Homand et al., 2001; Lee et al., 2001; Jafari et al., 2003; Liu et al., 2011, 2013). However, there are a few researches about the mechanical characteristics of rock joints under different shear deformation velocities because of the restriction of shear apparatus. Crawford and Curran (1981) conducted a series of one-way cyclic direct shear tests on four kinds of natural rock joints under different shear deformation velocities varying from 0 to 200 mm/s. The tests showed that at low normal stresses the peak shear strength of soft rock joints exhibited an increase up to a certain velocity, after which it remained essentially constant. For rock joints of intermediate hardness, the peak shear strength was essentially independent of shear deformation velocity; whereas for hard rock joints, the peak shear strength of which showed a significant variation with the shear deformation velocity. Jafari et al. (2003) carried out a series of conventional triaxial tests on artificial rock joints of regular saw-tooth shape with axial loading rate from 0.05 mm/s to 0.4 mm/s."

Jan 1, 2015

By Wang Xianzheng

For a long period of time, the Chinese Government has been attaching great importance to and supporting the rapid development of the coal industry. Particularly since more than 30 years ago, when China introduced the Reform and Opening-up policy, the reform and development of the Chinese coal industry has witnessed world-recognized achievements. National coal production increased from 618 million tonnes in 1978 to 3.52 billion tonnes in 2011. While China?s coal production accounts for 49.5% of the world?s total, its annual production growth contributes to over 80% of global production growth. China is a country utilizing coal as its main source of energy. As the Chinese Government gives support to the rapid development of new and renewable energy sources, as well as to increased coal utilization efficiency, the ratio of coal in the primary energy consumption mix will gradually decline. However, for a long period of time to come, the total volume of coal demand will keep rising modestly. The Chinese Government has been highly committed to and actively promoting the overall, coordinated and sustainable development model, which puts people first. It has put forward a strategic task to build an ecological civilization, and highlighted its resolve to uphold the basic national policy of resource conservation and environmental protection, with a view to the pursuit of sustainable development. China will incorporate its response to climate change into the national economic and social development program, and take effective measures to lower CO2 emissions 40?45% per unit of GDP in 2020 compared to 2005. At the same time, China will increase the ratio of non-fossil fuels to 15% in the primary energy consumption mix. All of the above factors have raised requirements for the Chinese coal industry, with implications for clear directions, plans and goals for the development of the coal industry.

Aug 1, 2013

By E. M. De Souza, A. M. Coode

"When Canadian potash was brought into production in the 1960s substantial research was carried out to develop the technology needed to cope with the unique conditions in Saskatchewan mines. The intense research has established Saskatchewan's position as a leader in production technology on a world scale, and as a leader in setting international standards for potash production. The industry is now more than two decades old and, although the mines operate efficiently, there are a number oj prominent areas of concern. High among these is the prediction, prevention and control of sodium rich brine inflows. Control has proven difficult or elusive in the potash mining horizon, but work continues in this area. Control of brine in the superincumbent limestone formation has proven to be easier and more conclusive.The first part of this paper describes the rehabiltation, diamond drilling, and grouting completed at Central Canada Potash, which reduced the brine inflow from approximately 82 l/min . at the beginning of the work to O.9/1min. when the backfilling was placed.The second part of the paper describes the rationale for choosing the rock mechanical instrumentation, the reasons for their placement and the rock mechanical data recorded with some interpretation.IntroductionCentral Canada Potash is located approximately76 km southeast of Saskatoon, near the Yellowhead Highway. The commercial production of potash at CCP started at the end of 1969 at a depth of 1021m below surface. The potash zone, which is presently mined, is approximately 3.35 m thick . Stress relief methods using yielding pillars are used in the design of the mining layouts. The planned extraction ratio averages 35070 . The mine is designed to produce approximately 3.3 million tonnes of sylvinite per year to give approximately 1.3 million tonnes of finished product (muriate of potassium) per year."

Jan 1, 1990

By G. Hamel

The LCL&L process (Low Caustic Leaching & Liming) is a patented hydrometallurgical route developed by Rio Tinto Alcan (RTA) to economically process spent pot lining (SPL) generated by aluminum cells. The three resulting end-products (carbonaceous, fluorinated and caustic liquor) are inert and have valorization possibilities. An industrial size pilot plant located in Saguenay (Quebec) was inaugurated in mid-2008 to demonstrate and optimize the technology. This paper describes characteristics of the LCL&L process and the experience acquired by RTA since the plant's start-up, including ramp-up capacity and technology challenges that were overcome. Possible end-products valorization methods are also presented. The carbonaceous end-product can be separated into carbon and brick rich fractions and used as either alternative fuel, reducing agents, or as raw material for third party processes. The development of a conversion process for the fluorinated end-product would allow its reuse as a substitute to fluorspar mineral for aluminum fluoride production. Finally concentrated caustic liquor is already valorized at the nearby RTA Vaudreuil alumina refinery.

Jan 1, 2011

By Wei Wang

The SMCO copper plant is located in DR Congo, and was designed by China NERIN Engineering Co., Ltd. The process is a typical hydrometallurgical plant with Leach-SX-EW, with the project treating the oxide minerals with agitation leaching, followed with three stage of solvent extraction and two stages of stripping, and using permanent SS cathodes to produce LME grade copper. Because of the special characteristic of the ore, what contains 2 different type of oxides (one high carbonate oxide and the other low carbonate), there are several new technical measures that have been developed and adopted for the plant. For example, different grinding, leaching, and filtering are used to treat different oxides. This paper, presents the project process, engineering design, construction and commissioning. The paper also describes some of the problems encountered during plant commissioning, such as the agitation leaching tank issues, and corrosion in the settler-mixer. This paper discusses some NERIN solutions to these problems, and explains the use of the CN filter, which is used to filter PLS to treat high level suspend solids, instead of the traditional sand filter. Finally, this paper also proposes steps / measures for further improvement for future plant operation.

Jan 1, 2014

By G. W. H. Norman

INTEREST in the mineral possibilities (gold, copper) of northern Quebec, north of the Quebec-Cochrane branch of the Canadian National railway, has centred for many years in the Chibougamau district (see Figure 1). Since 1934, however, promising gold discoveries in the Rose Lake-Florence River section, 115 miles southwest of Chibougamau lake, have widened the interest, and prospectors have examined other parts of the country between Chibougamau lake and Bell river and the surrounding districts. The object of this paper is to !resent an outline of the geology, and to describe the mineral deposits, o part of this region, or, more specifically, of the part embraced by the Opawica-Chibougamau and Waswanipi map-areas(l), which include the districts about Chibougamau lake and Rose lake-Florence river, where mineral deposits are now in course of development either by surface or underground work. Early discoveries, developments, and explorations in the Chibougamau district are well summarized in the report of the Chibougamau Commission, published in 1911(2). The Commission discredited previous optimistic accounts of mineral discoveries in the area, made initially in 1903, but at the same time they expressed the opinion that, from a geological standpoint, the district promised a reward to diligent and intelligent prospecting. Their general conclusion-that prospecting in the area was not then (1911) commercially advisable in view of its inaccessibility and other handicaps shifted interest from the district until, some years later, valuable discoveries were made in the Rouyn area, and aircraft widened the field of successful exploration. During the past ten years or so, considerable energy has been spent in promoting the development of the district. The net result has been the discovery of a number of prospects, the majority of which have been explored only by trenching and, in most cases, diamond drilling.

Jan 1, 1936

By G. Titichoca

Modification of the blasting process considers that any increase in the energy consumption generates greater benefits if done in the later stages (associated with a larger decrease in energy consumption). Therefore, although the blasting cost is doubled, generating a greater proportion of fines in addition to a weaker ore (because with greater loads and appropriate distribution of explosives a greater number of internal cracks is generated), the reduction of the unit cost that occurs in the grinding stages (SAG and ball mills) generates a positive balance in the overall size reduction process. Codelco Chile, Division Andina, has developed an extensive experimental plan to evaluate the concept of blasting modification applying greater energy. This was implemented in two stages, each including a specific mine sector: La Union and Don Luis. This paper reviews the experience of implementing such blasting modifications at the La Union mine and its impact on the design concepts and the operation of the SAG mill plant

Jan 1, 2007

By H. Warren Newcomen, Dennis C. Martin

"This paper describes the investigation of a large, progressive slope failure on the southeast wall of the east pit at Highmont Mine, British Columbia Geotechnical investigation s consisted of geological and structural mapping, assessment of blasthole drilling records, review of rock core information, slope movement monitoring and back analysis of various possible failure modes. Climate records and mining history were also assessed to determine their relationship to slope movement.Analysis of movement monitoring records and geotechnical information indicates that the failure is deep seated. The upper portion of the failure surf ace occurs along clay filled discontinuities. The lower portion of the failure surf ace appears to occur through the highly altered rock mass. High groundwater pressures and mining at the toe of the slope are documented to have had a major influence on stability at various times during the failure. Stability analyses results are presented and possible remedial measures are discussed.IntroductionHighmont Mine is located near Logan Lake in the Highland Valley approximately 50 km southwest of Karnloops, British Columbia (Fig. I). Mining of the porphyry copper and molydenum ore bodies began in 1980. In May, 1983, when mining in the east pit had progressed to a depth of about 60 m (200 feet) , a failure (designated the Southeast Failure) began to develop in the southeast corner of the east pit. Subsequent mining to a depth of 110m (360 feet) was accompanied by frequent and substantial slope movements involving between 500000 and I 000 000 m3 of rock . The slope was monitored extensively to assess short-term movement trends for operational safety. Geological mapping, core logging and rock mechanics testing were used in conjunction with the long-term monitoring information to determine the failure mechanism, conduct stability analyses, assess the effects of instability on pit design and enable design and installation of remedial measures."

Jan 1, 1988

By J. Makgatho, P. Condori, J. Winnett, Fischerm D.

"Palabora Mining Copper (PMC) has two autogenous mills that have been in operation since 1976. The mills were originally designed to treat 30 000 t/d of open cast copper ore in a closed circuit with cyclones. As the ore body went deeper the open cast method of mining was changed to block caving, a consequence of this was the dolerite content (hardest barren material) increased significantly, increasing the production rate of pebbles and thus reducing the milling capacity. In order to cope with the increased ore hardness and to increase mill capacity, a second ball milling stage and pebble crushing were incorporated to the circuit. The above actions created new challenges to the circuit operation and bottlenecks in different areas of the milling circuit.This paper reports the holistic work performed on the Palabora autogenous milling circuit including the implementation of a mill constraint control scheme, the implementation of a pebble removal system from the circuit and a new circuit configuration."

Jan 1, 2012

By M. A. Bergougnou, I. Inculet, K. I. Burgess

This paper describes the electrostatic methods of separating various minerals, reviews the principles of fluidization and outlines the technique of electrostatic sorting in fluidized beds. The application of the method to the benefication of coal is emphasized.

Jan 1, 1970

By George Wilkinson

"AbstractThe consistent relationship between the availability of electrical energy and our economic wellbeing is well known. As we develop the energy we need to nurture industrial civilization in decades ahead, we will at the same time reduce our reliance on dwindling supplies of oil and gas. Coal and uranium will be developed as our major fuel sources to meet medium-term. energy needs, followed by fusion and solar energy for the long term.IntroductionTHIS PAPER treats the matter of energy in a way that is quite different from that of the crisis-type atmosphere which surrounds so much of it currently in the news media. On the one hand, we lift the whole subject of energy out from its present-day involvement with short-term issues and take an important longer-term look at the solutions which lie before us. On the other hand, we recognize that short-term issues are important and, as we are reading and hearing, many of the right short-term solutions continue to elude our politicians, our policy makers, and even some of those with knowledge and authority in the energy field.A year ago, if you asked people how they would go about conserving energy, they would probably have said turn out the lights. They would probably say the same thing today, but they might also include other things such as driving the automobile more slowly or putting more insulation in the attic. However, their first impulse is still to use less electricity."

Jan 1, 1977

By I. C. Brown

Introduction Many tables of nomenclature for igneous rocks have been introduced from time to time, and each has its strong proponents. As a result, any discussion of igneous? rocks is apt to prove confusing unless the names used for these rocks are defined. This ?became so obvious to a discussion group, formed by the members of the Geological Survey of Canada in 1948, that an attempt was made to establish a scheme of nomenclature that could be used by any member mapping anywhere in Canada. The writer was asked to co-ordinate the ideas presented by individuals in the discussion group, to arrange them in tabular form, and, later, to distribute copies of the resultant table to Canadian universities, provincial geological surveys, and some other geological discussion groups. Many useful suggestions and criticisms were received, were studied ?by members? of the original group, and, so far as practicable, were incorporated in the scheme of nomenclature. The result is the table presented here. This nomenclature of igneous rocks is at present being used by most members of the Geological Survey of Canada who are working with igneous rocks, and by some Canadian universities. We hope it will be found useful and be more widely accepted. With this idea in mind, certain principles were adopted in drawing up the nomenclature.

Jan 1, 1952

By N. Valkanov

This paper presents results of an investigation into the connection between minerals liberation management and flotation, responding to lead-zinc concentrator ?Erma reka?, in Bulgaria. Monitoring of a Zn flotation circuit was carried out. The causes for the high silica content in the final Zn concentrate were established. Quartz is present mainly as liberated particles (> 60?80 %) in the fine fractions of the products; therefore the selectivity of the flotation process is not effective. Two approaches were tested to reduce the quartz content of Zn concentrate: froth washing in Zn cleaner flotation and new gangue depressants in the Zn circuit. Experimental results from bench-scale flotation and industrial tests show that it is possibile to reduce the silica content of final Zn concentrate more than 2 times without the need for extensive regrinding. The depression of liberated quartz particles on all operations of Zn circuit using stage depressant addition is the right solution to produce high-grade Zn concentrate that meets the metallurgical requirements.

Aug 1, 2013

By J. E. Hawley

"The zinc-lead deposit of the Lake Geneva Mining Company is on lot 7, con. VI, Hess township, Sudbury district, Ontario, about 10 miles northwest of the northern rim of the Sudbury Basin. Though a relatively small deposit, it shows some rather interesting relations to cross-cutting, pre-ore, quartz diabase dykes, which merit description.The deposit was discovered in October 1924 by J. H. Collins beneath iron-stained drift and oxidized sulphides. This proved to be the northwestern extremity of the orebody, the remainder of which extends southeast below swampy ground. Exploration began in 1927. In 1928 a vertical shaft was sunk to 250 feet and a level established at 235 feet. Later the shaft was deepened to 400 feet and new levels opened at 315 and 375 feet. In 1943 an inclined winze was sunk below the vein from the 315-foot level to a vertical depth of 640 feet, and two additional levels were opened at 525 and 615 feet respectively.The geology of the area has been described by T. T. Quirke (1), F. F. Osborne (2), F. J. Alcock (3), and Ralph Tuck (4). Private reports have also been made by Carl Tolman, J. E. Gill, and K. W. Fritzsche. Tuck's paper, covering the work completed to 1930, gives a detailed account of the character of the ore and enclosing rocks.Up to May 1944, when the property was closed, all ore above the 375-foot level and a small tonnage from below this elevation had been removed. Ore mined from 1941 to 1944 yielded the following:"

Jan 1, 1954

By D. M. Baird

"THE Island of Newfoundland lies on the extreme eastern edge of the continent of North America and at the extreme northeastern end of the Appalachian geological province. Its belonging to the Appalachian province is shown in the geological history of the region and in the rock types and structures.Geosynclinal sedimentation in early and middle Palaeozoic times was interrupted by Taconic and, more profoundly, by Acadian, mountain building activity. Mid-Palaeo-zoic intrusions range from masses of serpentinized ultrabasic rocks to granite batholiths. A Carboniferous overlay of continental and shallow, drying sea types covers the earlier developed complex. Local basins in these times were filled with products of the erosion of tl1e earlier rocks, and, locally, grew the right kind of vegetation to make thin, discontinuons seams and pockets of coal. Post-early Pennsylvanian history is one of erosion and pene-planation with renewal of movement along many of the older fault systems."

Jan 1, 1960

By Hagen B. Schultes

"Refratechnik, a leading German refractory company, acquired a majority shareholding in Baymag in 1979. This acquisition included the mining rights for a magnesite deposit of exceptionally high purity in the Canadian Rocky Mountains.The deposit, situated in the Kootenay region of southeastern British Columbia, is of Cambrian age and has ore reserves of 50 million m. t. of magnesite. The Baymag magnesite deposit is one of the purest in the world. The deposit was opened up and mining commenced in early 1982. Production of various caustic calcined magnesia products in a rotary kiln operation in Exshaw, Alberta, was started in mid-1982. The product application ranges from pulp and paper production, to the chemical industry, and to animal feed supplements. Since the end of 1983, Baymag has produced high-quality refractory grade fused magnesium oxide f or specialty applications in the steel industry.IntroductionAlthough magnesium is the eighth most abundant element in the earth and forms about 2.06% of the earth's crust, common knowledge about magnesium and especially magnesium oxide (MgO) as an industrial mineral is not widespread. The reason might be that, with the exception of magnesium metal as the element, magnesia products are not generally sold as final products to end-users, but rather are needed for the production of final products such as steel, cement, paper, etc. Therefore, some general comments are given about the different sources of MgO, the different products, world production and consumption , before Baymag specifics are addressed. Magnesium metal will not be discussed in this paper."

Jan 1, 1986

By R. J. Mitchell

"The use of hydraulically delivered classified tailings sands to provide ground support in large mining operations is still widespread despite recent developments of alternate backfilling methods and materials. The major disadvantages of the use of hydraulic fill are the costs and risks associated with slurry delivery. The main risk is that of bulkhead failure resulting from sand liquefaction due to insufficient operational control or due to dynamic loading from earthquake or rockburst. That risk may be eliminated by the pouring of a stiff cemented sand plug in the base of each stope prior to continuous fill pouring in that stope. An additional advantage of cemented plugs is that massive bulkheads are not needed. Instead, a temporary (removable and reusable) bulkhead can be used for plug forming.Physical model studies of fill pressures on a temporary bulkhead were carried out in a 3 m radius centrifuge facility. Fill pouring in-flight was carried out in order to model prototype stress paths. The results indicate that the average bulkhead pressure is likely to be less than 10 kPa under normal operating conditions and less than 20 kPa under the poorest anticipated operating conditions which include smooth walls, high slimes content and high water-content slurries. A portable bulkhead consisting of a central core and a surrounding sealing bladder was modelled and found to be effective. The use of different sizes of cores allowed the stress distribution adjacent to these bulkheads to be evaluated."

Jan 1, 1992

By D. C. R. Espinosa, P. Aliprandini, F. P. C. Silvas, J. A. S. Tenório, M. M. Jiménez Correa

"Nickel ores are divided into two types: sulfide deposits and lateritic deposits. About 60% of nickel resources are found in laterite ore, while the remaining 40% is contained in sulfide ore. Laterite ore is usually processed via pyrometallurgical means or through hydrometallurgical techniques that include acid leaching and metal value recovery from solution. In this study, copper and nickel adsorption by Dowex M4195 ion exchange resin from an acidic sulfate liquor was investigated. The acidic sulfate liquor was collected from an atmospheric leaching process (AL) of laterite ore. Ion exchange experiments were conducted in a batch system by varying parameters such as pH, time, metal concentration and temperature. Initially, mono-elemental synthetic solutions of nickel and copper were used in the experiments and then a synthetic solution simulating AL liquor was tested. Test results showed that the resin exhibited high selectivity towards copper and nickel, however, a high concentration of iron in the synthetic AL solution interfered with the recovery of nickel and cobalt by the resin.INTRODUCTION Nickel is one of the most important industrial metals in the world. It is widely used in industrial applications, such as the production of stainless steel, magnets, electroplating and special alloys (Dizge et al., 2009). The main sources of industrial nickel production are sulphide deposits; only 40% of industrial production uses lateritic ores. However, it is estimated that 60% of global nickel resources are found in nickel laterite deposits (Kuck, 2016). Since industrial nickel demand continues to grow, the development of new technologies for the extraction of nickel from laterite ores has become an interesting research topic (Agatzini-Leonardou, 2009)."

Jan 1, 2017