Search Documents

By Tamura S, Maekawa M, Nagai C, Deguchi M

Heavy fuel oil has been injected into blast furnaces in order to reduce the coke rate, to improve productivity and to control the furnace heat condition. However, in the first oil crisis at the end of 1973, it became necessary to develop an injection technique of new fuels into blast furnaces to reduce oil consumption. In Kobe Steel, Ltd., it was thought that the injection of a coal-oil mixture (COM) into blast furnaces could be developed in a shorter time than pulverised coal injection. The development of this technique was under- taken in 1974, and COM was injected through two tuyeres of the No.3 blast furnace at the Kobe works in 1977 and 1978. In addition, in order to study the combust- ibility of COM and the phenomena in the tuyere zone, the development of a gas sampling method was under- taken in 1975. In this paper, the results of the injection tests and gas sampling tests are reported.

Jan 1, 1981

By M Behrens, A McPhee, B D. Hegan

This paper describes the design and construction of twin 400 m long road tunnels as part of the Northern Motorway Extension Project in Auckland, New Zealand. Construction of the tunnel civil works is now completed and installation of mechanical and electrical systems is well underway. The tunnels are expected to be open for traffic at the end of 2008. The paper will address the design aspects of the project including: tunnel alignment and cross-section, geotechnical conditions and rock support, waterproofing and concrete lining and fire and life safety. The paper will cover the bored tunnel section, the cut-and-cover tunnel section, cross passages and portal structures. The design brief included a requirement for the tunnels to be a gateway to Auckland and this required particular attention to be given to the visual appearance of the finished tunnel structure. The final arrangement of the portal structures and a requirement for recesses in the concrete lining for emergency cabinets, deluge pipework and cable runs, reflects these requirements. The tunnels were excavated by a roadheader and road planer using a heading and bench. Initial support was provided by a combination of lattice girders, cement grouted rock bolts and steel fibre reinforced shotcrete. The permanent lining consisted of installation of a drainage geotextile and waterproof membrane, followed by cast in situ unreinforced concrete. Each portal consists of a cut-and-cover section. This paper describes the tunnel construction methods, including the particular requirements for safety, the environment and community relations. The tunnel is fitted with a compartmentalised deluge system for fire fighting purposes. The tunnel control centre is incorporated into the control centre for Auckland Harbour Bridge, some 30 km from the tunnel location.

Jan 1, 2008

By T Purvis

Xstrata Copper is extending the Ernest Henry Mine with a 6 Mtpa sub-level cave (SLC) mine being constructed under the pit. The SLC mine will maintain the EHM operation until 2024 after the pit is completed in August 2011. In February 2008, the first cut of the new underground mine at EHM was fired with the start of an exploration decline. Since then Xstrata Copper has continued the development and construction of a SLC mine. During this process a number of challenges arose, some of which had not been anticipated in the planning stages, that in turn has been addressed to ensure the development continued. The challenges have been many and varied and range from setting up the portal area and commencing the exploration decline development in an active large open pit, to management of underground water. Further challenges were presented by the effects of the GFC on investment recommendations, with the scale of the mine varying from a shaft mine to a smaller scale trucking only mine in mid-2009 and back to the full shaft mine in late 2009. The effect was the parallel development of two separate mining scenarios, with the challenge of maintaining commonality for as long as possible to keep both options alive until the final board approval was obtained. In 2010 the RSPT caused further impacts. This paper will describe the current progress of mine development as well as how the various challenges have been met and some key lessons learnt from these experiences.

Mar 21, 2011

The past decade hap seen revolutionary advances in com-munications and information-handling techniques which have been stiriulated by "cold war" military requirements and by, current programmes for probing into outer space: The tools used in exploration for petroleum and minerals have been improved significantly as a result of this new space age technology and even greater improvements are on the way.Two areas of technical activity have been particularly fruitful in enhancing the effectiveness of exploration, methods. These are (1) The development of new approaches, based on information theory, for extracting signal from noise more efficiently than before, and (2) The use of high-speed digital computers for storing and processing all kinds of exploration information, not only geophysical but geological as well.In seismic prospecting, use of information theory has led to new techniques such as time-domain filtering, wave-number filtering and correlation methods which have made it possible to obtain usable reflection data from areas which were previously considered NR. Complex playback and other data processing facilities have been developed to apply these approaches.

Jan 1, 1963

By J Dyt, S Lyons

In the mining industry, crusher-related incidents have led to 15 reported deaths in Australia, New Zealand, and the USA between 1998 and 2007 (NSW Government Resources Regulator, 2024). The majority of these fatalities occurred during routine crusher maintenance tasks. A survey of quarry and mine site maintenance staff was completed to ascertain what they thought of such safety device to understand if beneficial and if so reasons if unused. Overall, findings show, staff perceived risks differently, cost, familiarity, device awareness and not front of mind, influenced adoption. This underscores the importance of asking the right questions involving maintenance and safety staff to lead to more proactive risk assessment.

Apr 16, 2024

A description is given of a detailed examination of a coal bore core and of attempts to predict properties of equivalent "as-mined" coal using the bore core data so obtained. The accuracy of the prediction was measured by testing independently a large sample of coal which was produced under near mining conditions from a site adjacent to the bore core. Very encouraging results were obtained particularly in the prediction of size and ash distributions and washability characteristics of run-of-mine Coal.

Jan 1, 1972

By L M. Zhang, T H. Xu, J Zhao

Blasting is one of the most commonly used strategies for excavation in civil and mining engineering. Yet blasting can also bring along such undesirable effects as ground vibrations and soil disturbance. Numerical analysis is a powerful tool for estimating the effects of blasting and improving blasting design. In this research, a constitutive model for sand is proposed for the numerical analysis of blast-induced ground motions and wave propagation in soil mass. In the model, three model surfaces, ie the critical surface, the dilatancy surface and the bounding surface, are defined following the bounding surface hypoplasticity framework. The strain rate is included explicitly into the model formulations so that the proposed model is valid under high strain rate loadings caused by blast-induced vibrations. The performance of the proposed model is validated by the simulation of drained triaxial compression tests conducted on a crushed coral sand under different strain rates.CITATION:Xu, T H, Zhang, L M and Zhao, J, 2014. A bounding surface model for sand subjected to blast-induced vibrations, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By K Muller, T Oosthuizen

Blast exclusion zones are instrumental in protecting equipment and personnel. When there is no constraint in footprint, the exclusion zone can be enormous, practically eliminating the hazard of flyrock. Unfortunately, this may not always be the case and in many circumstances the blast design needs to be altered to suite such scenarios. When a conservative design approach is taken, it could completely eliminate any form of ejection, whether it is from the free face or the bench itself. The degree to which typical flyrock models describe fragment motion through air with ballistic flight equations are not justified when such a high level of control is applied. This paper examines various methods of risk analysis and suggests an approach to be used for controlled blasting.The outcome of principles discussed in this paper can be seen in video form (Mavmedia, 2014).CITATION:Muller, K and Oosthuizen, T, 2015. Should the blast exclusion zone be based on a qualitative or quantitative analysis? A practical implementation conundrum, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 425–428 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Since 1969, a substantial number of geophysical methods have been applied in the search for porphyry copper and mesothermal type -sulpha-de deposits. These have assisted with geological mapping as well as the definition of various sulphide depos-its. The application of these methods at the Frieda-Nena deposits, Papua New Guinea, can be used as a case study for exploration in other parts of New Guinea.In 1993, Highlands Gold Limited carried out an intensive geophysical program over the Nena deposit. The methods employed included, CSAMT (controlled-source audio magneto-tellurics), airborne and ground elect-romagnetics, IP/resistivity and ground magnetics. The magnetic method was used as a regional mapping tool as well as a way of mapping alteration zones over both the Nena and Frieda River copper deposits. Electromagnetics, in part-icular FLAIRTEM, is a rapid reconn-aissance tool as well as a detailed mapping tool for the location of Nena-style massive sulphide deposits. IP/ resistivity is an expensive but most useful tool for mapping out Frieda porphyry copper style disseminated sulphides as well as Nena style deposits. It can be used to define drill targets in areas of difficult Access.a

Jan 1, 1994

By R A. Pax

Electrostatic separation is a core requirement for the beneficiation of mineral sands suites to provide valuable product. Although the basis of electrostatic separation has been understood for some time, the details required to be able to calculate the metallurgical performance of a separator has not previously been achieved from a mechanistic perspective. Empirical models have had some success but require extensive test work. Traditionally, performance of an electrostatic separator is determined by careful experimental work using the target mineral suite. Although electrostatic separation was invented at the end of the 19th century, very little modification of the basic equipment occurred until relatively recently, with the addition of a plate electrode to aid separation. Previously, the author has presented results, calculated using finite element modelling (FEM), of the electric fields present in an electrostatic separator in various configurations. This paper will present some new mathematical modelling work, which uses the FEM determined electric field configurations but also incorporates some fundamental physical processes that provide insight as to the limitations and opportunities for this important separation technique.

Oct 5, 2011

By P Brown, M Nagarajan, A Green, P Dare-Bryan

Coal loss is an important issue at many coalmines, with losses of five per cent being common. The type of loss varies from mine to mine but is dependent on mine strata, the drilling and blasting processes applied and the mining method used. Typical coal loss mechanisms from the drill and blast process are coal roof damage and edge loss. Usually a reduction in coal loss is in direct competition with the need to provide material that is well-fragmented and a muck pile that has the required cast percentage. These competing issues were addressed over a two-year period at a mine in the New South Wales Coalfields by implementing a five-step approach. This was centred around building an understanding of the coal loss mechanisms utilising proprietary heave- modelling software, measuring coal losses by comparing survey to drill and/or gamma logs and implementing appropriate coal loss reduction processes. The end result exceeded expectations with a 95 per cent reduction in coal loss. Mine excavation productivity was maintained and coal loss minimised to less than one per cent of the in situ coal block.CITATION:Nagarajan, M, Green, A, Brown, P and Dare-Bryan, P, 2015. Managing coal loss using blast models and field measurement, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 429–436 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

White Cliffs Opal Field is situated in the Parish of Kirk, County of YulguIgra, New South Wales, about sixty miles from Wilcannia, and the River Darling. It is near the southern edge of the cretaceous basin of the interior of Queensland, New South Wales, and South Australia. Twelve miles south-west of the field, at Tarella station, a well sunk at the homestead reached silurian slates at about 127 feet, getting no water but about three miles north-west from the originally discovered and no central portion of the field, a well was sunk by the Momba, Pastoral cmpany, to a depth of 270 feet all the way through the cretaceous beds. At 250 feet a small supply of water was struck, but so much mineralised as to be quite useless. The temperature also was so high that a man could not keep his hand in it and Mr. Hogarth, the Momba Pastoral Company's manager, informs me that so corrosive was the action of the water, that a shovel left down the well for a fortnight, at the time of sinking, was completely eaten away.The well having now fallen in, I have been unable to obtain any of the water for analysis.The western termination of this portion of the cretaceous basin is situated about twenty miles from the present opal field, at which distance the slates, with (probably) devonian sandstones and quartzites resting unconformably thereon, commence to appear. The opal bearing country, as far as at present known, follows a more or less well defined line running north and south towards the northern end of the field, and north-east and south-west towards the southern extremity.

By P Radulovic, V Lawson, M Muller, J Wallace

The Mount Isa Copper Concentrator was commissioned in 1973. Since commissioning some significant upgrades have been undertaken such as: • the replacement of the rod mill/ball mill circuit with AG mills and the subsequent conversion of the AG mills to SAG Mills. • the introduction of columns as retreat cleaners in 1987, then reallocated as prefloat cleaners in 1994 and rougher cleaners in 1996.• the repurposing of some rougher capacity to preflotation roughing to remove carbonaceous pyrite and talc in 1994.• the introduction of a Jameson Cell for preflotation cleaning in 2000. • the expansion of the rougher and cleaner circuits in 2002 with the inclusion of 6 x 100 m3 Wemco cells to replace the capacity lost to preflotation and to increase residence time and improve recovery. In 2013 work commenced to replace the cleaner circuit after 40 years of operation. The new cleaner circuit, consisting of 3 x B5400/18 Jameson Cells, replaced the rougher cleaner columns, cleaners, recleaners and retreat Agitair banks and was commissioned in Sep 2015. The new cleaner circuit was configured as two cells in series producing the final concentrate and a cleaner scavenger cell to supplement the existing Wemco cleaner scavenger cells. The performance of the new circuit is discussed.CITATION:Lawson, V, Muller, M, Radulovic, P and Wallace, J, 2017. Mt Isa copper concentrator cleaner circuit redesign, in Proceedings MetPlant 2017, pp 279–287 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By R Lau

The fire safety design for road tunnels includes the following aspects: active systems, passive provisions and operational procedures. The active systems include the smoke control system, fire suppression system, detection system and fire fighter’s assistance systems. Passive provisions include escape passages, fire separation and fire resistance systems. The operational procedures refer to fire fighter access, reporting and alerts, evacuation processes and crowd control.Currently, these systems are typically designed by different designers or teams. These systems are intended to work together in a coordinated manner to provide the desired safety outcome. However, in practice, this is not always happening. The fire engineering process is supposed to bring together all these aspects and arrive at an integrated safety system. The fi re engineering process in practice is not integrating the design with the practice or reality and is thus arriving at less than desirably efficient safety systems.The example of design inputs shows how disconnected each system design basis is. The smoke control system design is based on the design fire size. The performance of the smoke control system is to achieve a smoke free environment for a defined space for a particular fire size – the design fire. The fire suppression system – most commonly sprinklers or deluge systems, is designed according to codes and to achieve a certain water discharge rate. The fire detection system is designed to detect temperature rise/rate of rise and perhaps density of smoke. Fire separation is determined to provide a certain period of service – mostly for structural elements. Escape route size and location is determined mostly by code compliance. Evacuation procedures are determined by Authority operational requirements rather than human behaviour.To arrive at an integrated fire safety system, the design basis and performances must be coordinated. An approach using fire scenarios would ensure all systems are designed to a common performance requirement. This paper will discuss how the current design approach outcomes compared with a fire scenario approach. More effective and efficient fire safety systems would require the stake holders to understand the implication of this approach and to embrace this through the fire engineering process.

Mar 8, 2011

With the use of 86 rock drills of the jackhammer type at the West Lyell Open Cuts of the Mt. Lyell Mining & Hailway Co., it is of importance to determine the economic as well as the physical life of these machines. With this purpose in mind records have been kept of the footage bored and the cost of new parts placed in each machine, and the following procedure adopted.A graph is plotted for each machine showing the footage bored as a horizontal line and at each 5,000 feet of boring the total cost of new parts noted on this line. (See l"ig. 1.) Thus at a glance it is possible to see... the amount of work done by each machine and the money spent on it in new parts. However, it is difficult to visualise from this graph the increase in the cost of new parts for each machine as its life advances. To obviate this difficulty a curve is plotted with the cost of new parts as the vertical component and the distance bored as the horizontal component. As before the cost of new parts are taken at each 5,000 feet bored. (See Fig. 2.) The curves so obtained are particularly interesting for two reasons:1. Each machine has its characteristic curve.2. The curve always steepens.Some machines are found to have relatively flat curves, others flat curves for approximately 15,000 feet of boring, and others steep gradients from the begining.This demonstrates that it is not always economic to discard a drill after it has been in service for a certain length of time or after it has bored a specified number of feet. Each drill has its own characteristics and so must not be regarded as one of a class, but considered on its own performance.The following use of these curve diagrams has been made to determine whether a machine has reached the end of its economic life. Figure 3 shows...

Jan 1, 1942

By J Lombardi, M Weidenbach

"OZ MineralsÆ Prominent Hill copper-gold concentrator is located 650 km north-east of Adelaide, 130 km north-east of BHP BillitonÆs Olympic Dam operation and 130 km south-east of the regional township of Coober Pedy, in the Gawler Craton region of South Australia. The concentrator was built in 2008 and commenced commercial production in early 2009. The Prominent Hill concentrator is comprised of a conventional grinding and flotation processing plant with a 10 Mt/a ore throughput capacity, operating well over the design rate of 8 Mt/a. Increased throughput rates have seen a decreased water recovery from the tailing thickener due to operating above design. Subsequently, greater pressure was placed on the site water balance and bore field off-take rates due to increased evaporation losses from greater volumes of water reporting to the tailing storage facility. This resulted in a trade-off between water availability and milling rates as part of the operating strategy.Two projects were implemented to increase the tailing thickener underflow density, thus improving water recovery directly back into the operating plant, reducing water losses via evaporation and decreasing the reliance on the bore field system operating at maximum rates to maintain mill throughput. The two projects were: tailing thickener feedwell redesign implementation of the Manta Cube control system.This paper discusses the background, implementation and benefits attained from these two key projects. Combined they have allowed a two to three per cent increase in tailing thickener underflow density to be consistently achieved, which has allowed greater water recovery. As a result, the processing plant has been able to operate at higher throughput rates when required, with greater water availability in the process plant recirculating system and a reduction in occurrences of the plant being æslowed downÆ due to water supply shortfalls. Both projects have also delivered a significant reduction in flocculant usage.CITATION:Weidenbach, M and Lombardi, J, 2012. Tailing thickener operability and control improvements at Prominent Hill, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 137-142 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 29, 2012

By M Behrens

The Melbourne Main Sewer Replacement (MMSR) is a major urban infrastructure project involving approximately 2.3 km of tunnelling and construction works. The works extend from Docklands Precinct, on the southwest edge of the city, southwards to connect with the Hobsons Bay Main Sewer in Port Melbourne. The tunnel boring machine (TBM) tunnelled section of the works terminates at the Yarra River where the delta geology and alignment requirements precluded the use of underground tunnelling methods. The 132 m long river crossing works involve a cut-and-cover excavation within a staged fl ooded cofferdam construction to construct an immersed tube tunnel as an extension of the TBM works.This paper reports on the development of the staged construction method and highlights the geotechnical and structural design aspects involved in building a new sewer in the Yarra River to close the gap between the new TBM driven and pipe-jacked tunnels.

Mar 8, 2011

By D Lees, D Gilchrist

Sydney has hundreds of kilometres of sewer tunnels. Many of these are over 50 years old and some have been in service for more than 100 years. The tunnels are predominantly constructed in Hawkesbury Sandstone and many are unlined.Principles have been developed over many years for the safety factor required in designing and constructing new tunnels but these do not necessarily relate to the operation and maintenance of existing tunnels, and in particular those that do not necessarily require personnel access for anything other than regular inspections.Assessment of the stability of these established tunnels needs to take account of their size, their age, their function, and their method of construction, as well as the geology in which they are situated and any support measures which have been installed. More importantly a stability review needs to take account of the consequences of a collapse, with regard to the inspection process, carrying out of any required repairs and the long-term performance of the tunnel.This paper is based upon the authors’ experiences inspecting and reviewing more than 200 km of tunnel in the last ten years. It will show some of the procedures and methods adopted by Sydney Water, how these can be presented as an acceptable procedure in line with other safety standards, and how they might be adopted for other similar historic rock tunnels.CITATION:Gilchrist, D and Lees, D, 2014. The development of a procedure for the inspection of unlined rock service tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 543–552 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Reed M. E, Cloutt B

Particulate samples were taken from the gas space in the settler of the Kalgoorlie nickel smelter using a vertical sampling probe and a specially designed isokinetic sampling probe which also quenched the samples. The vertical sampler was found to give unrepresentative samples. Suction thermocouple measurements of the gas temperature were also made. Using the isokinetic probe samples were taken at four points ranging from near the base of the reaction shaft to the base of the uptake at depths up to 1.5 m into the settler. Dust loadings and the sizing of the samples were determined. These parameters were found to be most affected by sample position and depth. The dust loading decreased along the settler but increased with depth. The loadings varied from zero near the roof to several hundred g Nm 3 near the slag. The dust also became coarser with increasing depth into the settler. Examination of the samples showed them to consist of spherical particles the largest of which were about 500 microns in diameter. The dust was mainly composed of mixed iron/nickel oxides with a little sulphide.

Jan 1, 1991

By J Rutter, E Amini, D La Rosa, N Beaton, M Scott, F Faramarz, L Keeney

Anglo American’s Los Bronces copper mine in Chile has been conducting detailed assessments investigating value adding options for their asset. The mine has conducted several detailed Mine-to- Mill and Grade Engineering studies to investigate increased throughput and head grade and to quantifying the impact of these approaches across the life of mine. CRC ORE has two key technologies namely Grade Engineering and the Integrated Extraction Simulator. These two technology suites have been combined to understand the technological landscape and associated value drivers suitable for application at Los Bronces. Detailed ore characterisation test work was conducted to:  measure and spatially model the propensity of ores to naturally deport and  develop customised blast models for Mine-to-Mill and Grade Engineering evaluation The outputs of this work were utilised to develop a block model populated with a range on new Grade Engineering and blasting parameters suitable for scenario analysis. To facilitate scenario analysis a high-fidelity value chain model of the Los Bronces operation from blasting to concentrate production was built in IES. IES was combined with sophisticated analytical tools such as Neural Networks to develop and reconcile a fully integrated value chain. The value chain model made it possible to simulate in IES all available blocks in the block model to predict throughput and grade changes for different strategic scenarios. The scenario analysis was run across 24 strategic combinations of Mine-to-Mill and Grade Engineering and comprised several million simulations. The scenarios investigated each technology independently and jointly to provide an attributed block model that can feed forward into technoeconomic modelling to determine optimal execution strategies for the mine. This paper presents the first published study combining Grade Engineering and IES to provide mass simulation capability to investigate strategic options for a mining asset.

Nov 10, 2020