Search Documents

By J Meinhart, J Rodler, I Katolicky

The ever increasing number of vehicles is leading to slow-moving and even stationary traffic sitting longer in traffic jams over extensive city areas. This traffic situation causes a sharp increase in pollutant emissions from vehicles, and high levels of pollution usually result throughout the built-up area. Reducing the pollution level by using traffic routing measures to speed up the flow of traffic in the existing street network is only possible in exceptional cases.In many cases the only option for achieving a significant improvement in traffic conditions is to shift the traffic underground using a road tunnel or underpass. Such tunnel routes suck off the traffic from large sections of the city, thereby easing the overall traffic flow. Thus on the one hand it produces a sharp reduction in pollution levels in the area of the tunnel route, but on the other hand it can result in locally increased exhaust pollution levels from longer tunnel systems that require mechanical ventilation. The air extracted by the ventilation system is blown out into the atmosphere either directly through the tunnel portal, or via a venting tower. Pollution can therefore occur in the area surrounding such exhaust air outlets.Thus if a tunnel is planned in a city, then closer investigation is required of both aspects: the reduction in pollution in the area of the tunnel route thanks to relocating the traffic and easing congestion, and the increased short-range pollution around the tunnel portals (shafts).

Jan 1, 1999

By R Ibarra, H Solis, G Teowee, B E. Papillon

The authors have previously described a piezoelectric-based system to measure the dynamic pressure during actual detonation in the field. This technique is used in a water hammer test set-up where a donor detonator is fired first, with the pressure sensor and an acceptor electronic detonator placed underwater in a water tank, and maintained at a fixed distance away from the donor detonator. The functioning and timing of the acceptor detonator are captured using a customised microcontroller board called the water hammer timer. Using such water hammer testing, the effect of dynamic pressure was studied as a function of the magnitude of pressure during the electronic timing countdown. Data obtained indicate there is no significant impact in the timing of the electronic detonators in contrast to what has been reported in non-electric detonators.CITATION:Teowee, G, Solis, H, Papillon, B E and Ibarra, R, 2015. Effect of dynamic pressure on electronic detonator timing, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 575–578 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The performance of the Australian Mining Industry over the past 10 years using key indicators of production, revenue, aftertax return investment, together with key cost elements, market changes and ore reserves is briefly reviewed. The elements of competitiveness are discussed forthe industry and the effects of Government charges and policies relating to existing operations are outlined. There is a demonstrated need for improvements in competitiveness in direct and indirect costs and for improved access to resources for the mining industry to continue to grow and add to Australia's economic growth.

Jan 1, 1987

By Laing W. P

Sedimentary structures are described from the WiIlyama Complex, New South Wales. Their presence confirms lithological layering within the metasediments as bedding. These primary structures occur not only in low grade rocks as previously reported by other workers, but also in areas of medium and high grade metamorphism.Sedimentary structures include graded beds, cross beds, ripple marks, and ball and pillow structures.The observed parallelism of the early schistosity and bedding in the Broken Hill area has previously led to the idea of transposition by isoclinal folding.In the areas mapped, small scale transposition is precluded on the basis of1. uniform facing of sedimentary structures over wide areas, and2. the existence of large areas in which the early schistosity is oblique to bedding.

Jan 1, 1975

By J D. Illescas, S N. Arnold, D R. Shaw

Ion exchange (IX) as a primary production technique has been applied commercially since the 1950s; its application in the uranium industry continues to be widespread and is utilised to a lesser degree in the gold industry. The majority of ion exchange applications, outside of gold and uranium, have primarily been for secondary metal recovery and impurity removal. Newer developments in the application of ion exchange, as well as changes in regulatory requirements, are bringing about the wider use of ion exchange as a primary production technique not only for high value metals such as uranium, platinum group metals (PGM), refractory metals and rare earths, but also looking at base metals such as nickel and copper. The ability to build lower-cost, safer, less polluting processing plants with smaller footprints is driving a greater interest in IX, with the main competitors remaining solvent extraction and carbon-in-pulp/leach. This paper discusses a number of areas where IX has been applied and its advantages compared with other techniques.CITATION:Shaw, D R, Arnold, S N and Illescas, J D, 2012. Ion exchange in hydrometallurgy - Secondary metal removal or primary production technique?, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 17-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By G Harbort, K Quan

Traditional engineering practice for concentrator design uses a mixture of risk minimisation options and capital minimisation approaches. Often this is based on the preferences and experiences of the engineers involved.A geometallurgical approach involves identifying primary lithology, alteration, and mineral dispersion patterns within a deposit to allow representative samples for test programs. This provides a method to infer from laboratory test results meaningful production data for larger amounts of the ore body. Geometallurgical models can be integrated into the resource block model and subsequent mine plan and can assist in predicting when difficulties in the processing route might be expected, allow adjustment of the design to compensate for these or provide an early warning system so that production forecasts can be more adequately developed. Simulation modelling is the process of creating a computer model of a real system based on mathematical logic. In simulated time, the model explores the randomness and chronological sequencing of events observed on real systems. The objective is to mimic the real system with sufficient accuracy to make predictions of real behaviour under experimental conditions. Amec Foster Wheeler often use the ‘discrete-event’ simulation modelling technique. This method is well suited for inclusion of the statistical variation of effects in unit operation, mechanical availability, throughput and operating strategy (based on historical operating data for equipment downtime), operating schedules and equipment capacity. The net result of the simulation model is an analysis that can quantify risks in terms of system performance and capital and operating costs.CITATION:Harbort, G and Quan, K, 2017. Concentrator design – standard engineering practice versus geometallurgy and simulation, in Proceedings MetPlant 2017, pp 195–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By N Elith

The explosives demolition of a post-stressed, steel reinforced, concrete road bridge in Australia’s capital city, Canberra. The bridge was 50 m from the new replacement bridge, 320 m from community structures and within five kilometres of the national parliament buildings. The job required multiple overlays of risk assessment, public relations, safe work procedures, specialised blast design, environmental predictions and flyrock controls. Project stakeholders included Worksafe, Roads ACT, bridge owners, consulting structural engineers, community groups and road users. The bridge precincts, including a major road underneath, had to remain operational to peak traffic in the days leading up to the demolition. The break-up and removal of debris had to be executed in just two days from Friday to have the road beneath re-opened for Monday morning city-bound traffic.In Canberra, all explosives demolitions are now viewed with particular caution after a demolition in 1997, during which a young girl was killed. Any approval requires that Explosives Regulations, AS2187 2006 and Worksafe processes are satisfied, and a convincing case presented for blasting as a safe and viable option.Our design used specialised shaped cutting and blasting charges to sever in situ concrete beams and tendons and to shatter components of the stressed concrete bridge assembly. We include comments on structural engineering reports dealing with pre-weakening mechanisms. The benefit of pre-weakening is that it reduces the amount of explosives needed to safely complete the job and facilitates quick removal of debris after the shot. The complementary skills of the team, each one an expert in his field, resulted in a highly successful demolition, praised by authorities as an outstanding example of controlled use of explosives.

Nov 8, 2011

By D Stepanenko, G Stovpchenko, L Lisova, D Togobitskaya, L Medovar

Classical electroslag remelting of consumable electrodes is a drop-by-drop melt feeding through a slag layer into a renewing molten metal bath, slowly solidifying into a homogeneous, dense, defectfree ingot in a copper water-cooled mould. The new look at the additive nature of the electroslag remelting (ESR) process in a protective atmosphere allowed us to formulate the principles of a comprehensive thermodynamic-based model that can predict dynamic changes in slag and metal composition at certain ingot remelting. The model considers drastically different slag-to-metal mass ratios at the beginning and end of remelting and predicts gas, slag and metal composition in a chain of thermodynamic subsystems. Despite consisting of calcium fluoride and stable oxides, the ESR slag can oxidise main and active elements from steel and alloys (primarily aluminium, titanium and silicon) due to chemical reactions between slag and metal. ESR is not an electrochemical process in its nature. However, slags are ionic melts and deviation in their composition causes a change in their properties, affecting both operation mode and ingot quality. Another important understanding derived from the modern metallurgy technological route is that the ability to refine metal from impurities is not a priority for the ESR because consumable electrode has already passed all stages of refining and deep degassing at ladle treatment that changes ESR slags engineering principles. The critical importance became slag’s ability to generate process heat and keep the melting composition in the metal bath unchanged (except for non-metallic inclusions assimilation). Slag engineering for ESR required a compromise between chemical inertness to a metal composition and desired physical properties deriving from technological reasons. The Directed Chemical Bonds Concept (DCBC) in a multicomponent oxide system was used to build predictive models of electric conductivity and the melting temperature of fluoride-oxide slag based on their chemical composition. Both models help to design a customised composition of effective slags for steel and alloy groups or individual grades, and they are significant steps in the development of a comprehensive model of electroslag remelting.

Aug 21, 2024

By B D. Saffron

In 1983, open cut coal mining operations were suspended at the Tent Mountain coalmine, located in Alberta, Canada in an area called Crowsnest Pass. Montem Resources (‘Montem’), an Australian mining company, purchased the asset in 2016. They conducted several drilling campaigns and undertook environmental monitoring with the intent to restart operations. In 2020, Montem completed a Definitive Feasibility Study, which indicated a mine life of more than 14 years.

Aug 2, 2023

By L Klemettinen, A Jokilaakso, D Attah-Kyei, P Taskinen, M Tiljander, D Sukhomlinov, D Lindberg

In this study, the use of carbon neutral biochars as reducing agents in the pyrometallurgical treatment of nickel slag was investigated at 1400°C in order to recover valuable elements such as copper and nickel from the slag. A large amount of slag is generated during the nickel matte smelting. Nickel slag contains valuable elements such as copper, nickel and cobalt, which can be recovered. Disposal of this slag results in loss of resources and may cause pollution of the environment. It is important to retrieve these metals for environmental and economic reasons. In this study, the slag was reacted with non-fossil reducing agents (biochar) which were produced from hydrolysis lignin and black pellet biomass pyrolyzed at 600 and 1200°C and with metallurgical coke for comparison. The reduction experiments were done at 1400°C for 15, 30 and 60 mins under inert gas atmosphere. The samples were quickly quenched and analysed with Electron Probe X-ray Microanalysis (EPMA). The results showed that the use of biochar resulted in faster reaction kinetics in the reduction process compared to coke. The fast reaction kinetics is attributed to the relatively high content of volatiles in this biochar, leading to gas formation and thus mixing of the sample material. Moreover, thermodynamic modelling was also performed using FactSage™ to simulate equilibria with different amounts of biochar. The metal to slag distribution coefficient calculated from the results of thermodynamic modelling were consistent with experimental results. In addition, thermodynamic calculations confirmed that nickel is reduced rapidly and it deports to the metal alloy phase. As the reduction progresses or extra reductant is available for reactions, more iron is deported to the metal phase. The calculations also revealed that Zn vaporises into the gas phase.

Jun 19, 2024

By R Bearman

The importance of crushers in the mining industry declined with the introduction and resultant dominance of AG and SAG based circuits, but the recent move to consider more energy efficient circuits has caused the industry to re-consider the role of crushers.Different types of comminution equipment have different efficiency in the way the energy is applied in the size reduction process. Because of the general trend towards more sustainable production processes and emission of carbon dioxide, energy use has become more important. To fully understand how crushers can contribute to optimising the energy application in comminution circuits, detailed models of process performance are required. Such models need to take into account the mechanical design factors and how the crusher performance changes in response to feed conditions, the control strategy utilised and the wear of the crusher liners.It is also critical to analyse the total circuit, not just the individual crushers. To fully understand the performance of the entire circuit, dynamic simulation should be applied. Without the holistic understanding of the total circuit and the incorporation of transient effects, the full circuit performance cannot be adequately determined and the true energy picture will not be quantified.Based on detailed mechanistic modelling of crushers by the authors and the application of dynamic simulation, the opportunities to optimise the use of crushers for energy efficiency are examined.

Aug 8, 2011

By J Manuel, L Lu

Increasing bed depth is one of the main options sinter plants consider to increase production, since it is an incremental improvement and less expensive compared with a new plant. To maximise the benefits of increased bed depth, correct blend design and plant operation is critical. This paper discusses test work conducted to show the effects of ore type and bed depth on sintering performance and the adjustments required in both fuel rate and lime addition depending on ore type. The differences in sinter plug macro and microstructure were also examined to show the effect of bed depth on ore assimilation and matrix formation. Finally, the benefits of blending ores to achieve the best sintering performance as bed depth increases is discussed.

Jan 1, 2007

The Favona Underground Project is located approximately two kilometres east of Martha Mine Open Pit in Waihi, 150 km south east of Auckland, New Zealand.   The underground reserve of 354 koz Au contained in resources of almost 600 koz lies within 600 m of the existing process plant presenting an attractive development target in a challenging environment.   The Martha Mine Open Pit is surrounded by urban housing on the north western edge of Waihi township and the Favona Underground abuts residences on the eastern edge of town. Environmental, community and social licence aspects influence project strategies as the new underground mine extends mining in a town that is planning for closure of current open pit operations in late 2006.   The Favona Underground Project has successfully passed through a detailed feasibility study, the third stage of the five stage Newmont project appraisal system. Methodologies used in the feasibility study and parallel permitting draw on a high level of stakeholder involvement to streamline the development and permitting phases.   This paper discusses the project appraisal process and design innovation required for developing an underground mine adjacent to town.

Jan 1, 2004

By G C. Snedden

Tandem row stator arrangements are common in the last stage of multirow, gas turbine compressors. Tandem row stators, or stator and de-swirler vane combinations are used to relieve the loading on the stator but ensure axial flow leaving the compressor. In this paper a standard 40” (1016 mm) ventilation fan in the Air Blow Fan’s range is modified to utilise the plate support struts on the barrel to relieve the aerodynamic loading on the aerofoil stator. Performance maps for both versions of the fan were generated using computational fluid dynamics and are compared across a wide range of rotor setting angles showing a clear advantage of approximately 2 per cent in efficiency for the tandem blade design. In addition, the area of high efficiency that represents the practically usable area of the map extends over a greater area in terms of flow rate and total pressure rise.

Oct 12, 2022

By Giles C. N, Loughnan F. C

Bentonites and active earths from N.S.W., previously analysed with respect to occurrence, mineralogy and physical properties have been evaluated for use as bonding agents in quartzose moulding sands in terms of green properties and behaviour both with and without coal dust for iron castings poured at 1400°C.INTRODUCTIONIn the paper by Loughnan .and See (Part I) the occurrence, mineralogy and physical properties of the fuller's earth and bentonites of New South Wales were discussed and it was shown that some of the materials approached the quality of Wyoming bentonite. In the present paper the same samples from Marulan (Bl), Boggabri (B2), Wingen (B3), Muswellbrook (B6), Swansea (B8), Dubbo (89) and Trida (Bll) have been investigated with respect to their potential value as bonding agents in compounded moulding sands. Inaddition, the -20 micron fractions of the Boggabri (B2t) and Swansea (B8t,> were recovered and the former converted to a sodium clay, in order to assesE; the beneficiation possibilities. A sample of Wyoming bentonite (S2) also has been included for comparison.GREEN PROPERTIES OF THE ARTIFICIAL MOULDING SANDSA quartzose base sand (Botany Dune) previously oven pried and screened to 1·65 mm., was subjected to a sieve ana]ysis in accordance with standard A.F.A. practice to yield a calculated' fineness number of 45. All tests were carried out on mixtures of this sand with2t per cent clay, since such mixtures were found most suit...

Jan 1, 1959

By N Petropoulos and M J Thurley, E Righetti, M Wimmer

Fragmentation in sublevel caving (SLC) is vitally important. Both gravity flow and any downstream processes are affected. Reasonably coarse fragmentation may lead to larger draw bodies (isolated extraction zones) and hence potentially higher primary ore recovery and depressed/delayed waste rock inflow from above. Fewer flow disturbances are expected by mitigating oversize. In addition, it requires less boulder handling and reduces wear and possible hang-up problems in orepasses. To assess the present-day functionality of large-scale SLC, a multiyear, comprehensive measurement program was initiated. It covers the main elements for SLC, namely blast function, fragmentation and gravity flow. The present paper focuses on fragmentation measurements. An image acquisition system was used to document the drawpoint and the load-haul-dump (LHD) bucket for each mucking cycle. At the beginning, four buckets (about 70 t total) were sieved to validate the results of both 2D and 3D image analysis techniques. The fundamental and specific problems are discussed herein. At the moment, fragmentation of the SLC rings is evaluated using a quick rating system and a 2D fragment delineation software. The results enable a description of fragmentation and its variation during mucking but also – combined with the gravity flow measurements – conclusions on the fragmentation for different parts of the SLC ring. Possible influences on flow disturbances and ore recovery/dilution are investigated. The recent findings allow a better understanding of breakage and flow and support future process improvements.CITATION:Wimmer, M, Nordqvist, A, Righetti, E, Petropoulos, N and Thurley, M J, 2015. Analysis of rock fragmentation and its effect on gravity flow at the Kiruna sublevel caving mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 775–792 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By B Shi, Y Li, L Ma, F Zhou

Subsurface fires are a common threat to coal mining, as spontaneous combustion of coal can potentially result in gas combustion and explosion. Fire-proof techniques, such as grouting, foam, or colloid injection, are not in a position to function ideally, due to the limited coverage and stopping the extinguishment substance from reaching the fire location. Liquid nitrogen, as a kind of all-submerged fire prevention or extinguishing method, can rapidly extinguish fires, thus preventing gas explosion and minimising extinguishment time. Injecting liquid nitrogen through boreholes is an important way during the period of mine catastrophe. But liquid nitrogen is not effective enough in infusion; technical issues restrict the development and utilisation of liquid nitrogen fire prevention and extinguishing technology. Immediate infusion of liquid nitrogen is usually associated with ‘air slug’ (the balloons and bubbles in the pipeline which hinder the flow of low-temperature liquid), which blocks pipelines for liquid nitrogen injecting. Another issue is that the pipeline tends to be damaged due to freezing, which undermines the injecting efficiency of liquid nitrogen and its application result. In order to solve the problems of the low efficiency and some other related field issues in liquid nitrogen perfusion, the ground–underground high efficiency liquid nitrogen injection technology were developed. Implementation of liquid nitrogen infusion techniques in Chinese coalmines achieved the goals of fire prevention and air-cooling. The technique presented in this paper is efficient in absorbing heat, and consequently, displacing oxygen and combustible gases. Field tests at Rujigou and Yangchangwan Coalmine justified the efficiency of the technique. By using this technique, there was no waste left behind, which may impede the subsequent production. The presented technique is of great benefit to the social, economic, and environmental aspects of mining operations, and will have broad applications in fire prevention for large-scale coalmines.CITATION:Zhou, F, Shi, B, Li, Y and Ma, L, 2015. Key techniques and engineering applications of stereoscopic liquid nitrogen infusion for coalmine fire prevention, in Proceedings The Australian Mine Ventilation Conference, pp 291–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Kasai H, Hibi T, Matsuishi S

Coal oil mixture (COM), a liquid fuel pro- duced by mixing together coal and heavy oil on the 50-50 basis, has been brought to a level of practical use in Japan, being actually employed by a oil fired system at Yokosuka Thermal Power Station of The Tokyo Electric Power Co., Inc. A COM Production Plant, built in Onahama which is located about 160 miles from Yokosuka, required COM to be transported by sea. Mitsubishi Heavy Industries, Ltd. therefore performed a series of studies to develop a spe- cialized COM carrier, the world's first of its kind. Long lasting high stability is of pri- mary importance to successful use of COM. Much have been done in the way of research on stability of COM in the static storage, and the mechanism of COM static: stability is almost completety known. On the other hand, the knowledge about the COM dynamic stability, such as the stability while being transported aboard the COM carrier at sea, is still limited at the moment. The motion of COM aboard the COM carrier and how COM would settle were studied by tests. A visualization test on the COM behavior under dynamic motion was also performed and the mechanism of COM dynamic stability was analysed. The tests showed that the ship rolling motion had @n effect of promoting the settling of coal content of COM in the cargo hold. And studies were also made to device a method for esti- mating the settling quantity of coal during sea Transportation.

Jan 1, 1987

By A Jurg, F Leclercq

The total drill and blast concept is widely known in the mining industry. On the contrary, the quarry industry rarely adopts such working methods. Based on the experience of the CBS quarry in the North of France, this paper shows how up-to-date blasting technology and simple control methods can significantly improve the overall Mine to Mill efficiency of a quarry. The CBS quarry, in partnership with the EPC group and Nitro- Bickford Company, adopted a new working process three years ago aimed at increasing blast performance and related productivity of the downstream process (loading, hauling and crushing). The pattern geometry of each blast is controlled and explosive charging is carried out following the æconstant specific energyÆ CSE concept. This method provides a homogeneous fragmentation distribution and reduces vibration peak-particle-velocities. The impact on downstream productivity is controlled by means of a simple information management system, which collects and measures key parameters of the production process such as; hauling cycles, crusher throughput, secondary breaking and vibration peak particle velocity. This information system has clearly proved over time that consistent blast quality could be achieved, leading to a 30 per cent improvement in quarry productivity. Improved energy control of blasting through optimisation with electronic detonators, allowed a significant reduction in vibration impact on the environment. Improvement in blasting security, reduction in the environmental impact and productivity enhancement are major benefits that quarries can obtain from these CSE optimisation blasting methods.

Jan 1, 2007

By R Varden

This paper summarises the process taken to simplify 35 ground support standards accounting for the multiple development profiles, dynamic geotechnical environment and the practical safety implications of a large-scale change in the ground control standards. This reduction was required after an incident involving incorrect standards being issued. The subsequent investigation identified that: • Selection of ground support standard for a mining instruction (MI) is not straightforward due to multiple standards, standards not reflecting current reinforcement used and complex geotechnical environment being encountered. Instead, site-specific ground control instructions were being issued. • Ground support standards were hard to follow and confusing, errors were present and not all standards to scale. • Ground support standards being used did not reflect what was being installed, ie bolt type incorrect and mesh orientation different. • No process or tier action response plan (TARP) for operators to follow for ground control standard noncompliance. • No justification for ground support standards being used in the current geotechnical environment. • No process for ground support standard selection and thereby no paper trail to document and assess adequacy of performance. A project was undertaken to reduce and simplify the ground support standards, produce a justification document to support ground support design and develop a process for site practitioners to identify the type of ground support standard required for the mining instruction. The exercise of rationalising the ground support was met with some challenges, including: • Technical aspects to determine the level of demand and the capacity for each ground support scheme. • Training the geotechnical engineers how to determine the level of risk for each area. • Winning over other technical services staff and the underground mining contractor of the new approach and then implementation. One of the major successes was the acceptance by the underground operators who found the system simplified their work and gave them increased confidence in management of seismicity. The rationalised ground support standards have now been successfully in place for over two years.

Mar 29, 2023