Search Documents

By E Kunz

Decreasing the gas content in the worked seam by degassing before the start of winning has proven its worth in some areas of German hard coal mines. On the one hand, it removes the risk of gas/coal outbursts and on the other hand it reduces the gas inflow into the longwall. The underground experiences of the last 30 years have led to a æhit listÆ of coal seams with respect to their suitability to predegassing. Trials in the DMT laboratory and also results gained in the deposit show that the suitability of a seam for predegassing depends on its rank. In seams with volatile matter of 20 - 30 per cent, high efficiency ratings are achieved as a rule, with lower ratings both in seams with lower and with higher content of volatile matter.If the rock pressure is unusually high, the efficiency rating of the predegassing is lower, even in seams which would normally be suitable for this process. Under unfavourable conditions, for example below or above residual pillars, in-seam boreholes cannot be drilled successfully and the method is not practical. But if the worked seam was already stress relieved, the predegassing has an optimal efficiency. Latest investigations show that the distance between the in-seam boreholes can be extended. But in that case, the time necessary to reach the same reduction of the gas content increases considerably.

Jan 1, 2005

By N Clarke, A Barros

Preconcentration of run-of-mine subgrade and marginal ore by screening has the potential to substantially improve the economics of mining, particularly for large, low-grade orebodies, and to reduce environmental impacts. It has recently been the subject of a major research effort by a joint public-private research body, CRCORE. Yet despite this, there appears to have been only one fully commercial installation, at Bougainville Copper Limited in the late 1980s. Two reasons for the limited application are that not all ores have suitable properties and the economics of all pre-concentration processes on low-grade materials are highly sensitive to the precise balance of mass and value recovery and to the pre-concentration process cost, including materials handling. These factors make it imperative to have good test data on the process response of feedstock across the orebody. Collecting that data presents major challenges, which differ for green and brownfields operations. This paper first discusses the approach to preliminary evaluation developed by CRCORE, which relies on testing of coarse rejects or drill chips available from exploration drilling programs. This method is an efficient first step in evaluating an orebody which is deemed geologically to be potentially amenable to screen upgrading, but it does have limitations and must be followed by larger scale work. A suite of methods have been developed by the authors as a result of test work since the 1990s on several projects, supplemented by published data, which aim to provide statistically robust data at lower cost than large scale bulk sampling tests. For greenfields projects, the upgrade response measured on material crushed to -53 mm has been found to correlate closely with ROM ore, with no scale-up required for material with upgrade responses in the range of commercial interest. Large diameter whole drill core, such as PQ, is expected to be suitable for this method. As drilling such core is costly, the aim should be to establish relationships between upgrade performance and proxy measurements such as multi-element chemical or hyperspectral analyses. This approach was successful at the Gramalote gold project in Colombia. The method is not applicable for ores with thick vein material comparable with the crush size, but such material is not suitable for upgrading by screening and would be eliminated by the preliminary testing. For brownfields projects where blasted material can be sampled, the upgrade response can be accurately measured by sampling only the finer fraction of the ore, selecting a top size which represents 30–50 per cent or more of the ROM size distribution. This is likely to be between 50 and 100 mm. The much finer size compared with the full ROM ore greatly reduces the sample mass required to achieve a given intrinsic sampling error and enables sample preparation to be undertaken with large-scale laboratory equipment rather than mobile crushing plant. The accuracy of the method can be improved by measuring the approximate mass of oversize rejected during sampling. Some ores do show a systematic deviation from the assumed model fit which results in this method slightly underestimating the upgrade response, and it would therefore still be recommended to take one or two full bulk samples to confirm results before a final investment decision.

Aug 24, 2022

By M J. Schultz, R L. Rude, D M. Tomko

The US Mine Safety and Health Administration (MSHA) conducted compliance assistance diesel particulate matter (DPM) sampling throughout the underground metal and non-metal mining industry. Based on that sampling, MSHA identified mines that were having difficulty meeting the DPM limit. To provide further assistance, MSHA then visited approximately 60 of the mines that were experiencing difficulty complying with the DPM standard. As part of these visits, DPM exposures were measured and control technologies for DPM were observed and assessed. Controls consisted of ventilation, clean engines, environmental cabs, alternative fuels, diesel particulate filters (DPF) and work practices. The focus of the follow-up compliance assistance visits was to assess control effectiveness and to make recommendations to mines experiencing difficulty in meeting the DPM standard. At each mine visited, the ventilation controls were evaluated, engine emissions were determined for equipment in use, environmental cabs were examined, and operational practices were noted. Additionally, control technologies, including alternative fuels and DPF were evaluated in several mines. A comparison was made of mine and section airflow to equipment particulate indices. Based on engine emissions, horsepower and operating time, the contribution of individual engine emissions to total emissions was made. Environmental cab integrity, positive pressure and air filtration systems were checked and operational practices relating to DPM exposure were assessed. This paper summarises the preference and magnitudes of controls that were typically used or needed for successful control of DPM. Additionally, results of the assessments of alternative fuels (including bio-diesel and water emulsion fuels) and DPF are presented.

Jan 1, 2005

By B Yeganeh, A Sam, A Kohsari

The base of separation at Gol-e-Gohar iron ore plant (Sirjan in the south of Iran) is magnetic separation after milling. Magnetic separation in the plant is divided into two parts: dry magnetic separation and wet magnetic separation. Sixty-five per cent of the plant production belongs to the dry magnetic separator section. Therefore, investigation of this part of the plant is necessary. Prediction of plant production is one of the most important subjects in mineral processing plants. That means, before feed enters the plant, specification of production has been calculated with laboratory methods. The purpose of this paper is the prediction concentrate quality has achieved from the dry magnetic separator. The content of iron in the final dry concentrate will be predicted, with laboratory, pilot and modelling methods, before feed enters the plant. Different variables are used in this approach, which consist of: speed of the first dry magnetic separator (rougher), speed of the third dry magnetic separator (cleaner), iron content in plant feed, size of 80 per cent passing of feed, size of 20 per cent passing of feed and iron content in pilot dry magnetic separation concentrate that performs in a standard manner. The artificial neural network is used for modelling and one of its branches is the radial basis network (RBN). Iron content in magnetic separating concentrate in plant will be introduced as the target and will be calculated with the RBN method. In the RBN method, a set of data enters to neural network and they will be trained and simulated. Finally, the target will be predicted. Ultimately, the original target (actual iron content) and the predicted target (predicted iron content) compare and error of them will be calculated. The obtained result is acceptable and satisfactory.

Jan 1, 2007

Hidden under picturesque Bemic Lake, in Canada's eastern Manitoba, lies a highly fractionated pegmatite orebody, hosting a unique assemblage of minerals. Accidentally discovered in 1929, the orebody had a brief history as a tin producer, but it is now mined by Tantalum Mining Corporation of Canada, Ltd. (TANCO), for its cesium, lithium, rubidium and tantalum bearing minerals. The mine also has potential for mbidium-feldspar, amblygonite, gallium rich mica, and quartz production. This paper describes the geology of the orebody, and its mining and processing. Selective, concurrent, mining and milling of the various products necessitates a high degree of planning and control, and these aspects are also discussed. The introduction of Quality Control and SPC are discussed, for such are the keys to excellence.

Jan 1, 1989

By F Weir, B Estrada

The impact of seismic loading on open pit slope stability in Australia is often only considered where the slopes are located adjacent to tailings facilities or other major infrastructure. The debate regarding application of seismic loading in open pit design in Australia is usually founded on limited reporting on significant damage of open pit operations during earthquakes, the common perception that earthquakes do not occur in Australia or that they are unlikely to occur during the mine life of the mine. It is frequently overlooked that pit slopes that have withstood strong earthquakes in highly active seismic regions are often designed under strict seismic guidelines. This paper discusses the factors that impact earthquake performance of open mine slopes. These factors include topography, slope geometry, rock material and mass properties, water management and intrinsic pit design. Further, the paper presents insights into the characteristics of earthquake activity in Australia such as magnitude distribution, earthquake depths, areas prone of earthquake activity and general seismic hazard that are relevant to pit design. Guidelines are provided on the conditions and circumstances under which earthquake design in open pit mining should be considered. In addition, this paper provides recommendation on the applicable methods for assessment of the impacts of earthquake loading on pit slope stability.

Jun 22, 2022

By Yianatos J. B

The advances in the study of control alternatives for flotation columns are reviewed. An integral solution to the control problem has to deal with problems associated with instrumentation, process modelling, control strategies and control algorithms. The term hierarchical control is used here to mean the intelligent integration of available knowledge, control algorithms and logic rules of decision. The selection of information, algorithms and rules is based on the experimental and theoretical knowledge of the column flotation process. The software support was designed and implemented in object oriented computer programs. This technique allowed the implementation of a combination of control techniques, algorithmics and heuristics, in the form of a control strategy. This strategy has shown to fit well with processes exhibiting complex dynamic characteristics. The hierarchical control was implemented in a pilot column and included the following general aspects: co-ordination of distributed conventional control loops, use of sets of control parameters for the froth depth control loop according to the froth depth state, verification and diagnosis of sensors, on-line predictive estimation of gas hold-up, diagnosis of common operating problems and the use of predictive control to account for feed flowrate changes.

Jan 1, 1995

The Mt. Sisa Orebody on Misima Island, P.N.G., consists of gold-silver mineralization associated with massive carbonate and amor- phous iron-manganese oxides in fractures and breccia matrix. The orebody forms the north- ern extension of the Umuna deposit. The mineralization lies within the three kilometre strike length of a northwest trending, 300 metre wide, high angle fault zone. The fault zone structure is deeply oxidi- sed, with the manganiferous oxide material resulting from oxidation of carbonate. The wallrocks are metamorphosed basement psammopelites and basic volcanic rocks, exten- sively intruded by microgranodiorite. These are dominantly epidotized and sericitized. The precious metals are associated with anomalous Cu, Zn, Pb, Mn, As, Ba, Ga, Sb, and. Mo. Many of the features of the Mt.Sisa mineralization are characteristic of volcanic- hosted epithermal deposits of western North' America. Lithologic and textural gradation is ob- served between the carbonate hydrothermal breccia-fill at Mt. Sisa, and the quartz domi- nated dilational fracture-fill mineralization which forms most of the Umuna deposit to the south. This gradational relationship is ana- logous to that within the Amethyst-OH vein system at Creede, Colorado, where it is shown to be indicative of deposition from laterally migrating fluids.

Jan 1, 1987

By P Waters, P Hollings, M Baker, D R. Cooke

Over the last three million years, porphyry and epithermal mineralisation in the Baguio Mineral District has been driven by calc-alkaline magmatism associated with the subduction of the South China Sea plate and the Scarborough seamounts beneath northern Luzon, Philippines. Coupled with extreme uplift and exhumation rates, mineralisation in the Baguio District has been responsible for the emplacement of over 922 million grams of gold. As one of the oldest intrusive bodies associated with the Baguio District, the Black Mountain Cu-Au deposit consists of at least five intrusive phases overprinted by potassic and propylitic alteration and sulfide mineralisation. Gold ore grades are low and molybdenum grades high with respect to other porphyry Cu-Au deposits in the Baguio Mineral District. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Bhattacharyya A. K

A major constraint on sustaining high rates of production in the collieries of the Southern Coalfield of New South Wales is the inability to develop panels fast enough to match the rates of extraction. This inability is particularly crippling in the case of retreat longwall mining and is due to nearly half the time in roadway drivage being spent on strata control operations such as roof support.Increased rates of roadway drivage and significantly improved roadway stability can be achieved by the application of yield pillars between parallel roadways. These pillars are designed to yield immediately upon formation and transfer the damaging roof loads away from the immediate vicinity of the roadways. Since the width of the yield pillar is the key to their successful application, it was determined through the Yield Pillar Experiment conducted by Kembla Coal and Coke Pty Ltd at West Cliff Colliery.Three experimental headings, each nominally 5.5 m wide and 2.8 m high, were driven to form two tapering pillars. The width of these pillars progressively decreased from 24 m to 3 m over a length of 154 m. The convergence between the roof and floor of the headings measured at various cross-sections corresponding to predetermined widths of the pillars are analysed in this paper to evaluate the stability of the tapering pillars at the different widths.The width of the yield pillar in a three heading development layout at West Cliff Colliery was determined to be 7.5 m.

Jan 1, 1995

By J J. Van Wijk, A R. Penney

Successful management of geotechnical risk at a mining operation is more than just having a good ground control management plan or using advanced numerical modelling and the latest monitoring technologies. The fundamental requirements for effective geotechnical risk management include identification of potential failure modes, identifying and implementing appropriate controls, and demonstrating the effectiveness of those controls. Effective geotechnical risk management requires an integrated approach by confirming that appropriate risk management systems have been identified and implemented (management plans, procedures etc), and that these systems are executed consistently in the field across all working areas. Development of a thorough integrated auditing process executed by an experienced team of technical subject matter experts with substantial operational knowledge, provides a more complete picture of catastrophic hazard management. Following consistent evaluation criteria allows benchmarking of systems and implementation compliance between the sites being audited, and the results can then be ranked against other operations in an industry database.

Nov 29, 2022

This paper reviews recent advances in geophysical tools for mineral exploration. It does not restrict comments to methods which are usually applied in the tectonically active belt surrounding the Pacific Ocean, where geophysics has often been secondary to geological prospecting (eg visual recognition of surface alteration) and drainage geochemistry; but considers geophysical tools applied to a broader range of both deposits and terrains. For example, the subdued topography of much of Australia and Canada has lent itself to the development and extensive application of airborne methods. In Australia, deep weathering and transported cover have necessitated the use of geophysical methods to not only detect anomalies but also to map and understand basement geology. This same weathering has caused specific problems, particularly for electrical methods, but recent improvements in instrumentation, processing and visualisation have largely overcome them. A great deal of geophysical data is now being collected by government agencies, often from the air, and made readily available to explorers. In several Australian states it is free, often on line, and in almost all cases it is relatively cheap. These regional data sets are often augmented by more detailed local surveys in areas of interest. Although æanomaliesÆ are still important much more is being done with the high quality data which is now available The results are used for geological mapping, to test geological hypotheses, to construct detailed 3D geological models and, together with fluid flow modeling, to predict optimum locations for mineralisation.

Jan 1, 2004

By M J. Newton

As part of the AMIRA P843 project Keeney and Walters (2008) describe how the principal components analysis (PCA) method can be used to identify classes of samples with similar metallurgical characteristics. However PCA does not take account of the location of each sample in 3D space. This paper describes a study to analyse the spatial distributions of the classes and determine appropriate modelling methods to control the estimation of the comminution parameters and mill performance indices into a 3D block model. This includes but is not restricted to geostatistical techniques that are used for grade modelling. The starting point for the study is the class definitions and the regression models for estimating the comminution parameters and performance indices. Each sample is assigned a class and the spatial distribution of each class has been analysed using different techniques including the calculation of variograms. This establishes whether the classes can be used as domain control for estimation into the block model – a procedure similar to using geological rock type domains for controlling the estimation of grades for a resource model. However, standard geostatistical estimation methods such as ordinary kriging assume that the variable being estimated is additive or linear. This assumption is valid for variables such as grade but this is not necessarily the case for the comminution parameters or the performance indices. Therefore the estimation procedure must either use variables that are definitely additive or the effect of potential non-additivity must be tested and accounted for where possible.The results of the study show how performance indices such as recovery, throughput and specific power can be estimated into the block model. This model is then combined with the geological model to provide a multi-parametric model that is used to optimise the mine planning and scheduling activities which can lead to significant improvements in NPV.

Sep 5, 2011

By J J. Eksteen

"In the platinum group metals (PGM) industry, smelters are often perceived as ‘black boxes’ that have to process concentrates of variable mineralogy and originating from multiple mines operating along strike or downdip from each other in the same geographical region, as is the case in the Western Bushveld of South Africa. However, PGM smelter complexes are much more sensitive to concentrate blend variation than most metallurgists or geologists would anticipate.This paper will review the impact of concentrate blends deriving from a number of concentrators processing ores from the Bushveld Igneous Complex (BIC) on smelting and converting behaviour and the constraints they impose upon smelter operation. Significant variation in behaviour is not only noted between the main mineralisation types, namely the Merensky and Upper Group 2 (UG2) reefs, but also within a given reef type. Due to the way PGMs are mineralised and finely disseminated, concentrators have to grind concentrates ultra-fine to liberate the PGMs and provide a sufficiently high-grade concentrate for smelting.The chemistry and mineralogy of the concentrates vary with the type of mine (open pit versus underground), the reef type and varies along strike; this variation impacts numerous key smelter parameters such as the base metals content, the matte fall, the converter aisle capacity, sulfur dioxide gas production, furnace matte and slag temperatures, and the accumulation of high smelting chromite-spinel minerals that has led to significant smelter upset conditions such as catastrophic furnace hearth and sidewall failures.Due to the production intensity of smelting, ie its high rate of processing per unit volume, smelters have been found to be far more sensitive to rapid variation in concentrate properties, highlighting the need for adequate blend control.CITATION:Eksteen, J J, 2016. Impact of Mineralogical Variation on the Smelting of Cu-Ni-PGM Concentrates, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 321–326 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Scott IR

In stratigraphic orebodies, estimation of footwall and hangingwall location is often of more importance than grade estimation. Contoured grade estimates often produce smeared boundaries and the use of accumulations and thicknesses as variables re-introduces the original problem: location of the point at which the estimate is to be made. The paper introduces statistical and geostatistical techniques for the solution of the problem and illustrates the techniques with a case study from Mount Isa, one of the world's largest producing silver-lead-zinc deposits. Solutions for calculating variograms in orebodies of variable dip, strike and plunge are presented together with relative variograms for individual metals, metal accumulation and orebody thickness. Optimal methods for hangingwall and footwall location are introduced and illustrated with an example. Orebody boundaries are then kriged after which individual metal grades are kriged within the estimated boundaries. The boundary estimates are compared with manually interpreted boundaries and known boundaries in mined-out areas. Grade and tonnage estimates are compared in mined-out areas.

Jan 1, 1986

By L Dubron

This study details a mineralogical and textural characterisation of West African iron ores with an emphasis on their behaviour during mineral processing. By means of both qualitative and quantitative characterisation, a simulation of the beneficiation process applied to these iron ores is performed. A series of different analytical tools are used, including:X-Ray Diffraction (XRD) for qualitative mineralogical analysis;• qualitative optical microscopy (phase identifi cation, description of micro-textures) and (semi)• quantitative optical microscopy (counting of particles, phases and textural types); and• chemical analysis.All the information provided by these analytical methods are combined into a quantitative mineralogical and textural analysis, here called ‘modal analysis’, which enables us to simulate the capability of West African iron ores to be benefi ciated by magnetic and gravimetric separation techniques.On one hand, both qualitative XRD and optical microscopy have revealed the presence of the following mineralogical phases: magnetite, haematite, goethite and quartz. On the other hand, the chemical analyses provide us with quantitative inputs expressed as oxides. We have converted the oxides into mineralogical contents expressed as magnetite, haematite, goethite and quartz. In this way, we build a simple quantitative mineralogical analysis.Beside this, the semi-quantitative approach of the characterisation by optical microscopy also provides us with a liberation study, enabling us to split the gangue-bearing content between two types of particles:1. liberated gangue-bearing particles, and2. composite particles composed by both iron (oxhydr) oxides and gangue-bearing minerals.We have assumed that we could anticipate the behaviour of these two kinds of particles through a mineral process, by simulating the removal of at least the liberated particles of gangue. Optical microscopy also revealed a trend in the weathering profi le of the Tokadeh ore horizon with a decrease from bottom to top of magnetite and an increase of both goethite and martite showing a higher level of oxidation and hydration in the upper ore horizon.We have applied this removal extent upon the quartz content of the mineralogical quantitative analysis and we have re-calculated the quantitative mineralogical analysis considering the expected decrease in the quartz content. Finally, by converting the re-calculated (oxhydr) oxides contents into iron grades and summing them, we do obtain a fi nal simulated iron grade for the upgraded products.

Jul 11, 2011

By Ormsby W. R, Nicholson P. M

Woodcutters is a polymetallic vein-style deposit hosted by sediments of the Palacoproterozoic Whites Formation which forms part of the sedimentary sequence in the central Pine Creek Geosyncline. Past production and identified resources total over eight million tonnes at 5.5 per cent lead, 12.1 per cent zinc and 110 gA silver. The local geology is influenced by Archaean basement highs; the Rum Jungle and Waterhouse Complexes. Unconformably overlying basement are interbedded clastic and crystalline carbonate units (Batchelor Group) representing cyclic changes in the depositional environment. These exhibit onlapping features with the underlying rocks. Sediments of the overlying Frances Creek Group suggest a quiet period during subsidence and subsequent increase in water depth (the carbonaceous dolomitic shales and the interbedded dololutites of the Whites Formation) followed by proximal uplift resulting in the inundation of turbiditic flows (Acacia Gap Quartzite). All of the Palaeoproterozoic rocks show evidence of being affected by penecontemporaneous, basement circling faults with steep dips. The stress regime during the deposition of the Frances Creek Group was characterised by alternating episodes of thrusting and transpression. Periods of relaxation also occurred. The compression resulted in major NS strike-slip (transpressional) faulting, en-echelon NNE trending folds and NW-SE tensional cross faults. Thrusting produced N-S striking, steep dipping reverse faults and a possible decollement immediately above the Batchelor Group. Relaxation is evidenced by the intrusion of lamprophyre dykes and dolerite sills (Zamu Dolerite). Mineralisation at Woodcutters occurred in faults within the Whites Formation, probably synchronous with deformation and the deposition of the upper parts of the Frances Creek Group. Greenschist facies metamorphism occurred as the rocks were further buried. Several massive sulphide bodies occur at Woodcutters. A number of features influence the location and shape of these bodies. They are: ò the N-S transpressional faults and in particular associated dilation zones; ò intersection of the N-S transpressional faults with the axial plane of the NNE trending Woodcutters Anticline; ò intersection of the N-S transpressional faults with the NW-SE cross-faults; ò intersection of dololutite rich units with the NS transpressional faults where local replacement takes place; ò thickening of the lithological units in the vicinity of the anticlinal axis; and ò the anticline doubly plunging to both the north and south. The mineralisation exhibits vein-like features as well as epigenetic textures. Its boundaries are sharp, its thickness varies rapidly down dip and along strike, and no alteration halo exists though stringer veins of quartz-carbonate-pyrite ¦ sphalerite/galena occur in close proximity. A number of sulphide mineral assemblages have been recognised, each separated by periods of deformation and partially replacing the earlier assemblages. Vertically continuous zonation patterns highlight the presence of rich galena-sphalerite-silver in zones of maximum dilation and pyrite-arsenopyrite-gold concentrated at the along strike peripheries. The genetic model proposed has the mineralisation occurring whilst the transpressional regime was active. It was deposited from the same fluid that elsewhere in the Geosyncline formed the stratiform deposits higher in the sedimentary pile. Hydrocarbons sourced from the organic-rich Whites

Jan 1, 1994

In the search for significant new economic base-metal resources within Australia during the early 1970s BHP's Exploration Department had observed that the majority of lead and zinc con- centrate production in Europe and the USA came from carbonate- hosted Mississippi-Valley-type (MVT) zinc-lead deposits, but Aus- tralia had no history of production from this class of deposit despite several very favourable geological environments, par- ticularly in the large Palaeozoic sedimentary basins. An exploration-research team was established in 1975 and the Lennard Shelf region, near Fitzroy Crossing, was selected as a most promising geological environment. Previous exploration for this class of deposit by other companies in Australia had largely used conventional exploration philosophies (geological mapping, geophysics and geochemistry to identify specific drill targets) but BHP sought specialist advice from a North American expert and adopted a grid-drilling philosophy, which involved wide spaced relatively deep diamond drill holes on a regular grid pattern, and statistical evaluation of the results. This technique resulted in the discovery of the Blendevale Deposit in 1978 in an area which had previously been explored by other companies using conventional methodologies. The deposit was delineated and a pre-feasibility study carried out in 1985 indicated that the resource of 20 Mt @ 8.3% Zn, 2.5% Pb was a marginal proposition.

Jan 1, 1988

By L Gobbo

X-ray diffraction (XRD) provides useful information about the composition of an ore sample in terms of quantification of crystalline phases and amorphous content. The use of new, fast detection systems implemented in CubiX FAST industrial diffractometers creates the opportunity to use this technique in exploration and modern process control. Besides the chemical composition of iron ores, their phase composition is also an important factor for exploration, quality control and processing. In the analysis of iron ore, XRD can identify the phases containing iron, such as haematite Fe2O3, magnetite Fe3O4, and goethite FeO(OH), and any other mineral phases present, especially silicas. Quantitative analysis is possible by various classical methods such as straight line or polynomial calibration with standards, but modern quantification analysis techniques such as Rietveld analysis or full pattern autoscale analysis are attractive alternatives, as they do not require any standards. These methods offer impressive accuracy and speed of analysis. Another analysis technique offering great benefit to ore exploration and process control is cluster analysis. This technique greatly simplifies the analysis of a large amount of data, eg from drill core samplings, and automatically sorts closely related scans of an experiment into separate clusters and marks the most representative scan of each cluster as well as outlying patterns. This can facilitate multi-dimensional compositional mapping of ore deposits, identifying regions of favourable mineral composition and allows fast and reliable tracking of the process. It is the most economic procedure to have automatic data evaluation without involving any dedicated personnel in the process. Details of the techniques used, sample optimisation methodologies, results, data precision and limitations will be discussed. The approaches have enormous potential as an inexpensive, reliable tool, useful in the characterisation of iron ore materials in an industrial environment.

Jan 1, 2009

Backfil ling of excavated Sub Level Open Stopes has been underway since March 1989 and as at December 1992 some 1 100 000 cubic metres of Cemented Aggregate Fill have been placed. During these three years significant developments in fill quantities, types and cost have taken place.Operational improvements have reduced the quantity of Cement Aggregate Fill by 40 per cent. These results have been achieved by:ò rescheduling stopes,ò designing smaller primary stope, and ò use of uncemented rockfill.Unit cost for Cement Aggregate Fill have fallen in the order of 50 per cent through:improving fill hole reli ability,simplified barricade construction procedures, reducing the cement content,ò substituting dune sand for deslimed mill tailings, ò improved maintenance at the Backfill plant, and ò renegotiated site freight agreement.This paper will review the historical developments of backfill use at Olympic Dam.

Jan 1, 1993