Search Documents

By K J. Davey, J T. Woodcock

Australian steelmakers produce up to 30 000 t/yr of electric arc furnace (EAF) dust. Current disposal techniques include sending EAF dust to landfill, stockpiling, and paying zinc smelters or registered waste removalists/processors to take the dust. Many of the complex overseas pyrometallurgical and hydrometallurgical treatment routes cited in the literature are not considered economic. Governmental, environmental and social pressures on producers to consider more sustainable disposal options are mounting, and there is now a strong push to consider recovering potentially valuable or recyclable components, such as zinc and iron units, from EAF dust. As well, there remain strong economic drivers for producers to find lower cost disposal solutions. Characterisation studies undertaken at CSIRO Minerals have revealed important physical differences in the nature of the zinc- and iron-bearing phases contained in domestic EAF dusts. These differences have been exploited using simple and cheap mineral processing techniques such as water washing, wet cycloning and wet magnetic separation. This has allowed a significant upgrade in the zinc content of EAF dust to be achieved, together with a reduction in the levels of key smelter penalty elements, such as chlorides and fluorides. The zinc-rich portion of the dust is now a more attractive smelter feed while the iron-rich part of the dust could potentially be briquetted or pelletised with a reductant and recycled to recover iron, and thus close the loop on dust processing. The basis of the separations tested together with laboratory results from several Australian dust samples are presented and discussed in this paper.

Jan 1, 2006

By Kendall W. T C

This paper provides a brief overview of the history of the Chaffers Dewatering Project which was successfully commissioned in August 1993. Until the end of 1992 the `Superpit' and the deep mines of the Golden Mile had all been dewatered by a staged pumping system from the 28 level in the Lake View Shaft, which was removed at that time when the Lake View Mine was absorbed into the Superpit. Feasibility analysis had indicated that adaptation of oil industry technology offered the greatest potential for a low cost solution to the problem of dewatering the open pit and deep mines. A KCGM engineer and one of the authors visited the Jackson oilfields to look at the deep well pumping technology in use there in early-1991. In the final analysis a new dewatering station was established in the 23 level crushing station of the Chaffers Shaft using conventional plunger pumps, but the rising main was screwed 178 mm OD (7 inch) casing the suspended from the surface to a depth of 686 metres, and was installed using oilfield personnel and methods. Only the second installation of its kind in Australia, the project achieved the dewatering objective at about half of the capital cost of the more conventional approach and at lower operating costs as well.

Jan 1, 1995

By A C. Robertson

World urban expansion puts constraints on the available land surface area of our major cities both for accommodating people as well as providing infrastructure and services whilst at the same time attempting to preserve the remaining natural environment. Whilst consideration is often given to underground planning for private and public transport infrastructure, the author is of the opinion that the current lack of underground planning of our cities that are suitable for underground development will have major long implications when finally the need for underground space planning is critical and ultimately recognised. This paper identifies the need for our city planners to integrate surface planning and underground planning as a ‘total planning solution’ where the city plan incorporates the elements of underground space planning as identified in this paper. Investigations by the author reveal that there are very few cities in the world that actually incorporate underground space planning in their city plans. The author uses the City of Brisbane as a case study for the potential introduction of underground space planning as part of the city plan. Despite efforts by the author to include the planning concept of underground commercial development in the latest Brisbane City Plan 2014 as well as four underground space workshops in Brisbane over the past 20 year through the Australasian Tunnelling Society (ATS), underground space planning for the City of Brisbane, apart from infrastructure projects, is not considered of significance to the City of Brisbane.CITATION:Robertson, A C, 2014. Commercial underground space – planned development for the future, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 513–518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By M Lak, R Amiri, A Haratian, M Asghari, S Haji

In recent years, due to advances in designing of various magnet assemblies, a wide range of magnetic materials with different properties can be concentrated. Jalal Abad iron ore beneficiation plant, which is located in Iran, Kerman province, is currently producing iron ore concentrate with the capacity of 0.8 Mt/a by having medium intensity magnetic separators (MIMS) with rougher and cleaner stages that finally leads to the production of an iron concentrate with the Fe grade of about 65 per cent. In this plant, the rougher tailings directly goes to the thickener as the final tailings and cleaner tailings feeds to the ball mill for regrinding. Since some hematite particles with weak magnetic properties cannot be recovered from only these two stages of magnetic separation, the obtained tailings from this concentration plant has approximately an iron grade of 25 per cent to 27 per cent. Accordingly, laboratory processing tests were conducted on the obtained representative sample of the final tailings. Based on the experimental results performed on final tailings, a new magnetic drum separator with a specific magnetic assembly was designed that could finally lead to product with iron grade range of 58 per cent to 60 per cent with relative and total weight per cent of 8.6 per cent and 3.86 per cent. Finally, it could be concluded that feeding of magnetite particles to the existing drum separators, due to their high magnetic field intensity, cannot efficiently lead to improvement of the grade of concentrate. Therefore, pilot magnetic separation tests were done on the final concentrate for evaluation of product upgrading probability. Consequently, by increasing another stage of cleaning and by decreasing the magnetic field intensity, the final product grade could be enhanced from 65 per cent to 67 per cent.

Nov 8, 2021

By R C. A Minnitt

The two methods for calibrating the parameters K and (alpha) for use in Gy’s equation for the fundamental sampling error (FSE), the duplicate sampling analysis (DSA) and the segregation fractionalised analysis (SFA) are described in detail. A case study using identical broken reef material from a Witwatersrand-type orebody is calibrated using the DSA and SFA methods and the results are compared. Classically, the form of Gy’s equation for the FSE raises the nominal size of fragments given by dN to a power of 3. Gy’s formula is a theoretical formula applicable in the case when fragments are randomly collected one by one, which is obviously never the case. This is because the fragment shape factor (f) and the granulometric factor (g) were introduced to take care of this anomaly. More recent formulae, such as those suggested by François-Bongarçon and Lyman, are empirically based formula. A later modification of Gy’s formula raises dN to the power ? (alpha), the latter term being calibrated with the coefficient K in the DSA and SFA methods. The preferred value of ? (alpha) for low-grade gold ores used by sampling practitioners in the mining industry is 1.5. A review of calibration experiments for low-grade gold ores using the DSA and SFA methods has produced values of K that vary between 70 and 170 and values of alpha in the range 0.97 to 1.30. The average value for alpha is found to be 1, rather than 3 as originally proposed in the classic form of Gy’s equation or the industry preference for 1.5. It is suggested that for low-grade gold bearing ores, the equation for the FSE should raise dN to a power of 1. Such an equation for the variance of the combined FSE plus the grouping and segregation error, now referred to as the short-term component of the quality fluctuation error (QFE1), greatly simplifies the characterisation of gold ores, which now only requires the calibration of K for a given mass and established fragment size. The implications for the heterogeneity test from the generalised equation are that provided the fragments have been screened to within a narrow size range, any particular size will return a value for K that is acceptable for use in the sampling nomogram.CITATION:Minnitt, R C A, 2017. A generalised form of Gy’s equation for gold ores – empirical evidence, in Proceedings Eighth World Conference on Sampling and Blending , pp 331–350 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By D J. Williams, A K. Kho, A Shokouhi, N Tucker

The disposal of dewatered coalmine tailings and coarse reject within spoil piles is gaining popularity as a means of eliminating separate surface tailings storage facilities or dams. The contrasting characteristics of coalmine spoil, coarse reject and tailings are somewhat complimentary, making the co-disposal of dewatered tailings within spoil piles geotechnically feasible and environmentally attractive. However, the impacts of mixing plant rejects within spoil piles are not well understood; in particular, the effects of water draining from the mixed plant rejects on the moisture content of the surrounding spoil. Changes in moisture content can cause additional collapse and degradation settlements of the spoil pile. A series of laboratory tests has been undertaken on mixtures of dewatered coalmine tailings, coarse reject and spoil. The results of these tests have been incorporated into a spreadsheet-based settlement prediction tool to investigate the effects of incorporating mixed plant rejects on total spoil pile settlements. This paper presents the laboratory tests undertaken, the incorporation of the test data into the settlement prediction tool, and settlement estimates for the various mixtures at different stages of construction.CITATION:Kho, A K, Tucker, N, Williams, D J and Shokouhi, A, 2015. Impact of co-disposing mixed plant rejects on spoil pile settlements, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By S Shafiee, N Abbate

The evaluation of mining projects requires a methodology that will give flexibility and manage the existing uncertainty within the projects. The discount cash flow (DCF) and other traditional evaluation approaches, which are widely used in evaluating a significant number of mining projects, have simply assumed that the main variables remain constant in their evaluation; elements such as discounted rate, mine life, operating cost and production rate. The DCF ignores managementÆs flexibility to adapt and reforecast and revise decisions. Real options valuation (ROV) is one of the modern evaluation methodologies that provide a tool to adapt and revise mining projects under uncertainty and future variables movements. ROV brings more variables into the evaluation model compared to DCF and assumes them as uncertain and dependent. Finally, ROV provides a range of solutions that can assist in managing this flexibility.This paper endeavours to compare ROV and DCF for mining projects comprehensively and applies these two techniques in the model. The paper shows that ROV will be inclusive of extra value in mining projects due to variables not allowed for, or even ignored, when the DCF model alone is used. One of the significant advantages of the ROV method is being able to evaluate mining projects under different scenarios from the inception of the projects. Furthermore, ROV gives the ability to evaluate the mining project while allowing for abandonment, temporary suspension, or expanding the mining project. In other words, the ROV evaluation process creates an analytical environment, which allows for optimisation of the mining plan within the mining project, as well as the ability to change the capital structure dependant on existing circumstances over the life of the project. The ROV is a new evaluation method that can add value in mining project analysis and offers opportunities to amplify gains, or to mitigate losses. This paper also discusses some of the reluctance to use ROV instead of DCF in current project evaluation.CITATION:Shafiee, S and Abbate, N, 2012. Now, this is the time for mining companies to choose - Real option valuation or discount cash flow, in Proceedings Project Evaluation 2012 , pp 225-234 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By Neill A, O&apos

The City of Kalgoorlie/Boulder is situated approximately 600 kilometres to the east of Perth (Fig. 1), and is the major regional centre of the Eastern Goldfields, supporting a population of approximately 25,000. The formation of Kalgoorlie Consolidated Gold Mines in 1989 brought the existing operat- ing entities adjacent to the city under common ownership and management. The Joint Venturers forming the management company are Homestake Gold of Australia and Gold Mines of Kalgoorlie (a Normandy/Poseidon com- pany). This traditional underground mining centre has been worked since 1893, yielding 40.8 million ounces of gold from ore with an average head grade of 10 grams per tonne. Historically the heart of the operation has been the famous Golden Mile located on the Eastern perimeter of the city, in the area known as Fimiston. The other significant operations that form KCGM are the Mt Percy Open Pit and the Mt Charlotte Underground Operation. KCGM's current production is 520,000 ounces per year, with the com- bined Fimiston operations (open cut and underground) contributing 400,000 ounces. The current expansion will increase production levels by a further 150,000 ounces. Traditionally 98 per cent of gold has been sourced from underground areas, however the recent upsurge of open cut operations is rapidly overturning this historical relationship.

Jan 1, 1991

By C Hedemann, N Silveste, H Davis, C J. Moran

For nearly two decades water scientists have been debating the need to use appropriate models for the questions being asked and the data available. This paper puts forward a rationale for a hierarchical framework for water balance modelling as it applies to mine sites. The hierarchy is based on the complexity of models and their data requirements. Scientific models are the most complex and require the most data; next is engineering models, then systems models and the simplest representations are given by conceptual models. A position is put forward that systems models have a range of uses that the others do not provide. A systems model, called SiteMiser, is described and its calibration illustrated. The model is applied to seven coal mines from the Northern Bowen Basin in Central Queensland. Currently, there is little relationship between total water use and coal production. This relationship is not any stronger when fresh (raw) water is compared to reused water. Leading practice water use levels are simulated for all sites. The simulation results demonstrate that there is considerable opportunity to reduce water consumption and, in particular, to import less fresh (raw) water to the sites.

Jan 1, 2006

By D Capstick, M B. Ebell

This paper describes the test work, process design, commissioning and operation of a processing system at the Ergo gold operation that improves the extraction efficiency from gold tailings material. The improvement in recovery is derived from the separation of the gold contained within the sulfides of the tailings material and a dedicated process stream to recover that gold.The sulfides are separated by means of a flotation circuit and that resulting concentrate is subjected to a regrind of below 20 ¦m to enable a greater liberation of the gold. The ultra-fine material is then subjected to a dedicated leach circuit to recover the now exposed gold particles.The case study is an example of the challenges of introducing new technology and methodologies to a well-established operation and thereby attaining improved efficiencies and tangible business benefits.CITATION:Ebell, M B and Capstick, D, 2013. Improving extraction efficiency from Witwatersrand gold tailings using flotation and ultra-fine grinding of concentrates, in Proceedings World Gold 2013 , pp 301-306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

Listing on Australian Stock Exchange Limited ('ASX') is a means by which a company can prosper and grow by gaining access to a large capital market. This currently stands at over $300 billion for domestic securities listed on ASX. A company seeking listing will benefit from a higher profile and a greater spread of shareholders. These result from, among other things, improved communications with the investment community. ASX recognises that a decision to list is an important step for a company. Owing to the diverse nature and size of the companies that consider listing and the various steps involved, it is recommended that guidance of professional advisers is sought as early as possible in the listing process. A company seeking listing on ASX must meet the prerequisites for admission to the Official List which, along with the continuing obligations that must be complied with following admission, are contained in the Listing Rules of ASX. Listing on ASX requires a company to ensure that, among other things, the market is fully informed at all times so that investors can make informed investment decisions.

Jan 1, 1996

By H Thanasekaran, M J. Mankosa, J N. Kohmuench, G H. Luttrell

"Fluidised-bed flotation has been demonstrated over the last 16 years as an effective method for improving the flotation recovery of coarse particles. This technology has been successfully deployed into the industrial mineral sector with multiple installations within phosphate beneficiation plants and potash mills. Due to the minimal mineral surface expression required when utilising this technology, more recent studies have centred on the applicability of using this HydroFloat™ technology for the recovery of coarse sulfides and base metals. Multiple approaches have been investigated to determine the best means for implementing this novel coarse particle flotation system into both existing and new plant circuitry. These include the treatment of tailings to recover values that have been lost using conventional technologies and also the direct treatment of a coarse feed, either within the grinding circuit or by use of a separate split-feed flotation approach. Recent applications of the technology will be presented along with data generated from several test campaigns and ongoing research investigations. The benefits of properly applying this technology, such as reduced power consumption and increased mill capacity will be discussed.Citation:Kohmuench, J N, Thanasekaran, H, Mankosa, M J and Luttrell, G H, 2016. The Impact of Fluidised-bed Flotation for Treating Coarse Sulfides, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 105–112 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Q Gong, J Li, J Zhao, Y Zheng

Excavation by tunnel boring machines (TBMs) offers many advantages over conventional excavation methods, in terms of safety level, working environment, advance rate and overall cost. While TBMs have been extensively used in civil tunnel construction, they are also viewed as a competitive alternative to the drill-and-blast method for underground mining, attracting increasing attention from the mining industry. This paper presents an overview and general assessment on applications of TBMs in mines, by reviewing more than 60 TBM applications in underground/open pit coal and hard rock mines around the world. The projects range from the early exploratory trials of TBMs in mines in Germany, England, South Africa and America in the 1960s and 1970s, to the ongoing projects in Australia, China and Chile. The paper focuses on the geological compatibilities, the problems encountered, the solutions undertaken and the lessons learned from those projects. The paper summarises the progress made in the past and highlights the challenges faced by TBMs in mining due to complex ground conditions and geometrical requirements. With the technological advances of TBM and experiences gained in the past, more applications of TBMs are expected in underground coal and hard rock mines.CITATION:Zheng, Y, Gong, Q, Li, J and Zhao, J, 2014. A review of the applications of tunnel boring machines in mines, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 691–704 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A G. Sheard

Fire safety requirements inside tunnels have become more demanding as tunnel designers consider the impact of potentially larger fires. Tunnel ventilation equipment is required to clear hot gases in the event of a fire. This is vital to maintain smoke free escape routes for people trapped in the tunnel and to facilitate safe access for emergency services. As the fire becomes larger, the temperature of clearing hot gases increases. Traditionally, engineers have taken into consideration gas temperatures of 250°C when designing tunnels. Because of larger fires, engineers must now design equipment to clear hot gas up to 400°C.Increasing the temperature of hot gases to 400°C requires tunnel ventilation equipment that goes beyond historic limits. As temperature rises, material strength reduces, consequently mechanically constraining fan aerodynamic performance. Developing tunnel ventilation equipment suitable for clearing hot gases at 400°C requires a fan technology that is more typical of industrial turbomachinery. The standards EN 12101-3:2002 and ISO 21927-3:2006 defi ne the necessary design criteria and testing methodologies to verify that a range of tunnel ventilation equipment is capable of extracting hot gases.This paper describes the process by which the authors certified in accordance with EN 12101-3 and International Organization for Standardization (ISO) 21927-3 a range of powered ventilators suitable for clearing smoke and hot gases at 400°C for two hours. Proving the high temperature capability of the new range provided a challenge as a consequence of the large physical sizes and high motor powers involved. Additionally, the need to install vertically, as well as horizontally, imposed high thrust loads on motor bearings, further complicating both mechanical design and testing. The paper presents the methods by which the authors overcame these challenges.

Mar 8, 2011

By S C. Barrie

St BarbaraÆs Marvel Loch operations have successfully used longhole open stoping as the primary mining method for a number of years. A transition to Core and Shell mining was implemented in 2009 to recover substantial ore grade resources remaining in sill and rib pillars. The transition to core and shell for the Exhibition lode required continuous waste filling of created voids and thus the removal of the crown pillar at the base of the Exhibition pit by blasting. Access to the top of pillar was denied as the pit was partially rock filled with waste rock from underground development.Beyond the technical challenges of the blasting project, a simple and transparent risk management process was developed to ensure appropriate controls and mitigating strategies were in place to minimise risk to personnel during the pillar removal process.Although failure of the crown pillar was anticipated but with the actual timing unknown, on 25 December 2011 the crown pillar yielded during normal mine operations. Engineered and isolation controls in place at the time were of a sufficiently high standard to ensure limited exposure of the underground workforce and minimal damage to mine infrastructure. Successful risk management through implementation of appropriate controls during the project lifecycle of two years and three months proved to be fundamental to the safe removal of the crown pillar.CITATION:Barrie, S C, 2012. Successful risk management through project life cycle for removal of the crown pillar at the Marvel Loch Underground Mine, in Proceedings International Mine Management 2012, pp 125-134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By J E. Wajon

This paper discusses the background, requirements, need and content of plans for management of drinking water self-supplied to mining-related operations, including construction camps, especially in remote areas of Western Australia. The paper discusses the importance of cooperation between regulators, the mine site operator and the consultant in preparing a plan fully compliant with the Australian Drinking Water Guidelines to protect the quality and safety of drinking water supplied to mine sites. The paper outlines some of the issues that need to be addressed in preparing a drinking water quality management plan, such as hazard identification, risk assessment, the multiple-barrier approach and the concept of critical control points. Data requirements, monitoring, incident management, training and reporting are also covered.CITATION:Wajon, J E, 2013. Drinking water quality management for mining operations in Western Australia, in Proceedings Water in Mining 2013 , pp 321-328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

As Pliny commented two millennia ago, The only certainty is that nothing is certain. Despite the many breakthroughs, advances and promises, the way we each live and work remains awash with technological, economic and political uncertainty. The resources sector is no exception in this regard. Mining itself is much more than a complicated process or recipe; it is a complex adaptive system. The way we adopt and adapt new technologies, the way we evolve data into corporate wisdom, the way we make decisions and even the way we view our concept of rationality should each be the subject of intense review. Translating these sentiments into sustainable company growth is indeed the challenge. This is unlikely to be achieved within convention, but through innovation. The game is changing!

May 1, 2010

By I C. Carrasco, V G. Mirada, J F. D Domingo, F S. Leite

This paper investigates ore loss and dilution produced by rock movement in bench blasting. A total of four blasts, in which electronic detonators have been used, were monitored in Cobre Las Cruces Open Pit Mine (FQM Ltd) in Gerena (Sevilla, Spain). Rock motion has been obtained in 137 points of the free face and 6 points inside the block. Multiple liner regression has been applied to predict rock motion and estimate ore dilution as a function of hole coordinates, rock contacts, powder factor/hole, amount of explosive per blasthole, burden, spacing, hole length, stemming length, explosive energy, hole row, subdrilling, blast sequence, stiffness ratio, blasthole distance to free face, rock density and Young’s modulus. The model is statistically significant with a determination coefficient over 0.8. Rock motion measurements in 31 more points have been used to validate the model and to show a reduction in ore dilution.CITATION:Domingo, J F D, Leite, F S, Mirada, V G and Carrasco, I C, 2015. Dilution, ore grade and blast movement calculation model, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 71–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By P Navarra, R Kuhne

Dynamic simulation (discrete event simulation) is the preferred methodology to evaluate the impact of dynamic aspects of processing plants on the overall plant capacity. This tool can be used to: identify bottlenecks in the plant,justify upgrade and expansion projects by evaluating their impact, oroptimise maintenance and operating practices without disrupting the operation. Iron Ore Company of Canada's (IOC) pelletising plant is a complex operation because of multiple products, varying equipment capacity and shifting bottlenecks. Furthermore, with extensive capital requirements for projects and long lead times, a high level of confidence in project outcome is required. Therefore, a model of IOC's pelletising plant in Labrador City was constructed in 2007 by a joint IOC and Hatch team. The model includes both operational and metallurgical aspects in order to better capture the complexity of IOC operation. In this paper, the justification, boundaries, and functionality of the model are described. A comparison of simulation results to historical plant operation is given. It is observed that projects have interactions and that the benefits of combined projects are not equal to the combined benefits of the individual projects. Projects can have synergies that result in greater benefits when combined or can have overlapping benefits that result in lower benefits when combined. The power of the proposed modeling exercise lies in the ability to assess the impact of projects on overall performance.

Jan 1, 2009

Intrusion related Cu/Au mineralisation is localised in Pacific Rim island arcs by arc parallel, termed accretionary structures; or arc normal, termed transfer structures. In Papua New Guinea, NE trending transfer structures, evident on Landsat imagery, represent deep crustal fractures which have facilitated dextral rotation of the mainland during oblique plate collision. Major structures localise intrusion centres, and by rotation, develop ore hosting dilational environ-ments in subsidiary structures. While transfer structures localise the Porgera, Wafi and Yandera porphyry centres, the Frieda Porphyry and associated Nena high sulphidation Cu/Au mineralisation are localised by accretionary structures. The Bulolo Graben, which hosts the Morobe Goldfield, developed during intra arc rifting aided by movement on transfer structures. Crustal thinning has initiated magmatism with which diatreme breccias and fracture controlled mineralisation are associated.

Jan 1, 1994