Search Documents

By W. F. Durfee

The apparatus described in this paper was designed by the writer, in the year 1869, for use in the laboratory of the " American Silver Steel Works," at Bridgeport, Conn., where only the vacuum-pump was erected ; but on two subsequent occasions I have had the combined vacuum-pump and table-blowpipe constructed as represented in the drawings, in which Fig. 1 is a general elevation of the apparatus, the air-chamber being sectioned vertically; Fig. 2, a plan of the air-chamber; Fig. 3, a vertical sectiotnal elevation of the vacuum-pump, the section being on line C L), of Fig. 4, which is a horizontal section on line A B, of Fig. 3. The vacuum-pump is constructed of copper, and consists of a vacuum-chamber, E, supported upon the upper expanded end of a vertical pipe, Q. The vacuum-chamber is provided with four nozzles, C, F, I, D (Fig. 4), two of which are shown in section at A, B (Fig. 3). Passing vertically through the centre of the vacuum-chamber E, is seen the water-supply pipe P, whose lower extremity incloses an internal pipe p, which is supported, and placed in communication with the vacuum-chamber E, by means of the two elliptical nozzles n, n. The upper part of the pipe p is closed by a conical cap, and its lower end is in the same plane with the extremity of the watersupply pipe P, within which it is placed. The relative sizes of the pipes P and p are such that an annular adjutage, one-sixteenth of an inch in thickness, is formed between their lower extremities, through which the water from the supplypipe P passes into the pipe &, drawing any air that may be in the

Jan 1, 1885

By S. F. Reiter, W. R. Hibbard

A survey of the effect of heat treatment on the room temperature hardness of Fe-Mo alloys has been made. Constant strain rate tensile tests were performed between room temperature and 1800°F. These data were analyzed to determine the effect of temperature and composition on the strain hardening coefficient and strain rate sensitivity. Constant load creep-rupture tests were made on these alloys and the results related to composition and structure. A relation between the high temperature strength of the precipitation hardened alloys and the volume of precipitate has been observed. IN view of the extensive use of ferritic materials at elevated temperatures, it is surprising to note the limited amount of information relating the variables of plastic deformation, i.e., composition, structure, temperature, stress, strain, and strain rate. Hollomon and Lubahn' showed how the several variables of plastic flow might be treated analytically. No data were available on carbon-free iron and its alloys in a form suitable for this analysis. Several German investigations2-" constitute most of the experimental work relating high temperature properties to the constitution of these types of materials. In order to obtain new data, the iron-rich alloys of the Fe-Mo system were selected for detailed investigation for the following reasons: 1—Some of the important effects of molybdenum on the mechanical properties of iron have already been studied.' , 821 2—By suitable heat treatment of selected alloys, it is possible to study strengthening effects of four types: AT -a transformation, B—substitutional, C—precipitation, and D—dispersion of hard inter-metallic compound. Materials and Treatment Four-pound ingots were vacuum cast, employing the same melting schedule previously used.? The raw materials were electrolytic iron and lamp-grade molybdenum. The ingots were forged to l/z in. sq. rod and one portion swaged to 0.350 in. diam rod for the production of 1 15/16 in. long button-head specimens. The button-head specimen blanks were solution treated for 16 hr at 2100°F in hydrogen of —70°C dewpoint and then water quenched. They were subsequently plunge ground to the standard 0.160 in. diam test bar. Micrographs of the solution treated alloys are given in Figs. la through Id. The higher molybdenum alloys contained large equiaxed ferrite crystals similar to those in Fig. Id. A portion of the % in. rod was hot rolled to 0.100 in., sandblasted, and cold rolled to 0.020 in. Strip tensile specimens having a 0.020x0.200 in. cross-section and a 2.25 in. gage length were machined from the sheet. The alloys containing molybdenum were subsequently annealed 1 hr at 1560°F. The iron strip was annealed 4 hr at 1300°F in wet hydrogen. The resultant structures are shown in Fig. 2a through h. The ASTM grain sizes were 1 to 3 as solution heat treated or 3 to 4 as annealed. The chemical analyses of the alloys are given in Table I. Carbon contents were obtained after the heat treatments in hydrogen. Alloy 15.9 pct Mo was tested as a cast alloy.'

Jan 1, 1956

By Harlan W. Nelson, James B. Purdy

A study of data obtained during laboratory tests to determine the suitability of bituminous coals for use in residential underfeed stokers of the clinkering type has led to the following general conclusions: 1. Performance data obtained during the test furnish useful and practical information upon which to judge the performance of stoker coals. 2. Conclusions derived from the results of evaluation tests are in general agreement with use experience of the coals in the field. The method is of practical use in this regard. 3. Few direct relationships were found between data furnished by the evaluation test and determinations by standard laboratory tests. This is particularly true with regard to coke formation and clinker formation, two of the most important factors in determining the degree of satisfaction to be obtained in applications of the small underfeed stoker. It has not been the intention in this paper to prescribe this evaluation test as the best method for the evaluation of coals for use in residential stokers. That there are other test methods having similar objectives serves to point out the necessity for full-scale laboratory tests. At the present time, a standard test procedure for the evaluation of coals for use in residential stokers is not available. For the past several years a joint committee, appointed from the membership of the Residential Stoker Committee of Bitulninous Coal Research, Inc., and from the Engineer- ing and Research Committee of The Stoker Manufacturers Association, has been working to develop a standard procedure for testing and evaluating bituminous stoker coals. This procedure has been completed to the extent that it has been drawn up in tentative form. It is now planned to install the equipment in several laboratories and to run check tests, using portions of identical lots of coal, to determine the degree of reproducibility offered by the method. Completion of this standard test procedure should greatly facilitate the evaluation of coals for use in residential stokers. Acknowledgments The cooperation of coal operators sponsoring the coal evaluation tests, in granting permission to use data and results from their tests, is gratefully acknowledged. Acknowledgment is also made to Carroll F. Hardy, Chief Engineer, Appalachian Coals, Inc., for his interest and timely suggestions on the preparation of this paper. Special thanks are due to Ralph Sherman, Assistant Director, Battelle Memorial Institute, who was largely responsible for development of the evaluation procedure, for helpful suggestions and advice. References I. H. A. Sherman: The Evaluation of Coal for Use in Domestic Stokers. Univ. of Ill., Eng. Experiment Station, Circular No. 39 (1939). 2. . Q. Shotts: The Relation of Free- swelling Indexes to Other Characteristics of Some Alabama Domestic Stoker Coals. TP 2314, Coal Tech., (Feb. 1948); Trans. AIME (1948) 177, 502. 3. . J. Helfinstine and C. C. Boley: Correlation of Domestic Stoker Combustion with Laboratory Tests and Types of Fuels 11. Combustion Tests and Preparation Studies of Representative Illinois Coals. Ill. State Geol. Survey, Re1. of Zntlestigations No. 120 (19467 ) p. 35. DISCUSSION E. R. Kaiser*—AS a former fuel engineer assigned to residential stokers at Battelle, the writer has read with considerable interest the paper by Messrs. I'urdy and Nelson. It is gratifying to note that earlier test techniques have been developed and that criteria found important in the years 1935 to 1938 are still important in judging the performance of stoker coals for residential heating. The authors have plotted a number of the primary coal data singly against performance data of the stoker in an effort to establish relationships. Unfortunately, wide scattering of points usually resulted, which did not illustrate what experience generally indicates to be the case. For example, Fig 3 indicates almost no trend in the percentage of released ash converted to clinker with change in ash-softening temperature. Other factors, such as fuel bed temperatures and zones of heat release must have influenced the results. In the present state of our knowledge, we cannot explain all of the reasons why suitable stoker coals perform satisfactorily, nor why one satisfactory coal may be better than another. It would therefore

Jan 1, 1950

By Robert H. Richards

Very little has been published recently on this subject in the mining journals or proceedings of societies. The attention of experts has been diverted perhaps by the demands for pan amalgamation of refractory ores. Yet free milling ores occur in many localities, and it may be interesting to have on record some data as to details of running a small test-mill, especially as details of results do not seem to be accessible to stndents and investigators. Küstel, in 1863, under battery amalgamation, dismisses the subject by stating that "amalgamation on copper-plated platforms, troughs, and other copper fixings" is " very imperfect, and mostly abandoned." J. Arthur Phillips says, in 1867, under placer mining : " A well-amalgamated copper plate is considered as effective for

Jan 1, 1880

By Noel Jarrett, Allen S. Russell, Bernard M. Starner, Stanley C. Jacobs

A process has been developed to refine high-grade commercial aluminum to 99.99 pct purity. This enzploys precipitating titanium, vanadium, and zirconiu~ as borides. The upgraded liquid is partially crystallized under conditions that prevent massive freezing. The resulting crystals are compacted and washed free of adhernig impure liquid aluminum by melting the top crystals while draining off the liquid. Finally, the bottorn portion of the crystal bed is melted and removed as the pure product. Leakage from the crystallizat~on vessel is prevented by a layer of alumina granules that are not wetted by the aluminum. ALUMINUM of 99.99 pct purity is desired in a variety of applications. These include electrolytic capacitors, catalyst carriers, decorative trim for automobiles, aluminum powder, and high-strength alloys. This market was for many years filled by refining commercial-purity aluminum in a three-liquid-layer electrolytic cell of the type originally proposed by Hoopes. To meet the expanding need for lower-cost high-purity aluminum, a refining process based on chemical precipitation and fractional crystallization was developed. The availability of this super-purity metal was announced in November 1961, and three patents1-3 relating to the process were issued in 1965. An alternate process, comprising continuous fractional crystallization of a portion of a liquid-aluminum feed stream under conditions of strong agitation at the surface of the growing crystals, was published by Dewey4 in 1965. Earlier proposals by Larsen 5 and by Regner6 also emphasized the advantage of rapid agitation of the melt in the region of the crystallization zone. johnson 7 more recently proposed extracting purified aluminum from an alloy by mixing crystals of pure aluminum into the molten alloy, allowing them to grow, and removing the pure aluminum as by casting. Aamot's 8 recent patent describes a freeze refining process that involves controlled partial freezing against cooled moving retort walls. The Alcoa process to produce high-purity aluminum is schematically described in Fig. 1. Relatively pure aluminum is treated with boron in a furnace (a) to precipitate high melting point impurities, the supernatant liquid is transferred to a crystallization vessel (b), the liquid is partially crystallized with mechanized "tamping" (c), the remaining impure liquid is tapped out and the crystal bed partially and directionally re-melted to wash the underlying crystals (d), and the balance of the crystals is melted and withdrawn as high-purity aluminum (e). PRINCIPLES OF FRACTIONAL CRYSTALLIZATION Commonly encountered impurity elements form two types of systems with aluminum. Titanium, vanadium, and some other transition elements in periodic groups IV, V, and VI are the high melting point impurities. Initial solidification of aluminum containing small percentages of these elements will produce solid markedly enriched in them at temperatures slightly above the freezing point of high-purity aluminum. Most other elements, such as silicon and iron, produce eutectic type reactions with aluminum. In this case the first solid formed on initial solidification at temperatures slightly below the freezing point for high-purity aluminum is markedly depleted while the remaining liquid is enriched in these elements. The equilibrium change in composition during solidification of aluminum contaminated with silicon, iron, or titanium is illustrated in Fig. 2. Here, for clarity, the temperature scale is expanded beyond the

Jan 1, 1968

By F. Louis Grammer

THE difference between blast-furnace gas and ordinary producer-gas is chiefly that blast-furnace gas is richer in CO, and poorer in hydrocarbons and hydrogen, as is shown in Table I. TABLE I.-Volume-Composition of Producer-Gas and Blast-Furnace Gas.. Producer-Gas. Blast-Furnace Gas. Per Cent. Per Cent. (Volume.) (Volume.) CO . 22 to 33 25.5 00., . 6 to 3 13.0 H . . 13 to 7 1.5 CH, 3 to 1.5 0.0 N . 54 to 60 60.0 If natural gas, water-gas, or by-product coke-oven gas be available, blast-furnace gas can be made to resemble very closely in calorific value the average producer-gas by merely mixing in one of these products, which are richer in hydro-carbons and, hydrogen. Blast-furnace gas, however, possesses a virtue which is sometimes absent in producer-gas, especially with coals very high in sulphur-namely, that blast-furnace gas is relatively free from sulphur. In some regions the sulphur in coal is an acute problem, and it is highly desirable to find uses for the products which are specially high in sulphur-content. An advantage would be gained if coal was coked before charging into the gas-producers, but this adds to the expense. Sulphur may be partly eliminated from coal by washing it, the success depending upon the form in which the sulphur occurs, and upon the efficiency of the washer, but it cannot always be removed to the extent desired at most American plants. It is not practicable to remove all the sulphur from producer-gas by washing it, though Mr. Reinhardt, of Germany,

Sep 1, 1908

By T. H. Aldrich

(Chattanooga Meeting, October, 1908.) Tars paper is intended only to give a preliminary account of experiments made, and conclusions reached, concerning the treatment of certain refractory low-grade gold-ores, the profitable reduction of which may furnish a useful guide to the solution of similar mining and metallurgical problems, not only in the gold-bearing belt of the Southern United States, but perhaps in other regions also. It must be regarded as simply a ?report of progress," preceding a more elaborate and conclusive report of regular practice. The mines of the Hillabee Gold Mining Co. are located upon what is generally known locally as Hog Mountain, on the northern edge of Tallapoosa county, Ala., about 15 miles from Goodwater and 14 miles from Alexander City, stations on the Central of Georgia Railway. Gold has been known since 1839 to exist on this property, where it was discovered in that year by a man named Johnston. The property was worked for placer-gold by the old miners, and there are now the remains of four attempts to operate it by stamp-mill and plate-amalgamation. The present owners purchased it in 1896, and since that time they have experimented at frequent intervals, in order to devise a process that would satisfactorily recover the gold. In 1903 regular operations were begun. Geologically, the mountain consists of an intrusion of what has been pronounced true granite in altered sedimentary slates. The cooling of the granite produced shrinkage-cracks, which have become veins. There is considerable question as to the period of the slate formation; but it is undoubtedly, in my opinion, of Carboniferous age. The veins, about 50 in number, strike N. 60° to 80° E.; dip approximately 65° from the horizontal; vary from a few inches to 25 ft. (being in gen-

Nov 1, 1908

By C. H. Green

Recently two papers on the structure of eutectics were read before thc British Institute of Metals, one by F. L. Bradyl and the other by A. Portevin. 2 In the preparation of photomicrographs of laboratory specimens as illustrations for student work, and in connection with various researches, the writer has been working along the same line for some time and, therefore, was much interested in the results given, especially those of Portevin. He has correlated the information on the subject and has outlined a broad scientific basis for future work along this line. It is largely with the idea of adding something by way of illustration to the work already done that this paper is written. The eutectic is generally understood to mean the alloy having the lowest melting point of any alloy of the system, and in which the melt becomes supersaturated with reference to the two or more phases which separate out simultaneously or alternately. From the surface pattern, the eutectic means a structure with no primary crystals. It is not always easy to get the exact eutectic composition in making any alloy; in fact, a slight range in composition may be expected and some of the coarser particles may be richer in either of the composing metals. Even when chemical analysis shows the right composition, differences in density of the pure metals may cause segregation, or supercooling resulting from different crystallizing properties may give a surface pattern the appearance of being on one side of the eutectic point. However, the alloys on either side of the eutectic composition, showing primary crystals of one of the phases and the effect of the proeutectic form on the surface pattern of the eutectic make a very interesting study, which is slightly touched upon in this paper. The phases, or microconstituents, of a eutectic may be pure metals (Pb-Sb, Tl-Au), solid solutions (Cd-Zn), a pure metal and a solid solution (Ag-Sn), or a pure metal or solid solution with an intermetallic compound (Sb-Mg, Sb-Cu, As-Cu, Bi-Te, etc.).

Jan 1, 1925

Jan 1, 1947

Jan 1, 1947

By Harold B. Treweek

The development of full scale flotation circuits based on laboratory and/or pilot plant data is discussed. Auxilliary operations, equipment and layout essential for trouble-free start-up and operation are noted. The selection of flotation cell size is discussed as it affects plant capital and operation costs.

Jan 1, 1978

By B., Hoyaux

A first requirement for assessing the safety of a rock slope, either artificial or natural, particularly if the rock behaves in an elastic-brittle manner, is a proper knowledge of the distribution of stresses within the slope and their development with time and advancement of workings.

Jan 1, 1972

By S. R. B. Cooke, H. S. Choi, I. Iwasaki

In magnetic taconite of the East Mesabi range, quartz, magnetite, and cummingtonite (OH}(Fe, Mg)(Si4O11)2) are the three major ore-forming minerals.' Fine grinding and magnetic separation of the taconite leads to a concentrate analyzing 64 to 65 pct Fe and 8 to 9 pct insoluble; the gangue content of the concentrate arising from the presence of locked magnetite-gangue particles, and of occluded gangue particles in magnetic floccules. To further upgrade such taconite concentrates, flotation appears to offer a particularly promising approach. To evaluate its effectiveness in separation, a knowledge of the flotation characteristics of each mineral comprising the concentrate becomes desirable. The floatability of magnetite and of quartz have already been reported in a previous paper,2 in which the flotation characteristics of the two minerals were correlated with the electrokinetic properties at the mineral-solution interfaces. Since cummingtonite has somewhat intermediate chemical composition between the above-named oxides, the electrokinetic and the flotation behavior of this mineral becomes of interest for both practical and fundamental reasons. In the present article the results of electrophoretic mobility measurements and of Hallimond tube flotation tests on cummingtonite are reported and are compared with those of quartz and magnetite. MATERIALS AND METHODS A sample of cummingtonite-rich taconite, received from the Mitchell pit, near Babbitt, Minn., was crushed and ground through 100 mesh, and the product was fractionated magnetically into three portions. First, a drum-type laboratory cobber was used to separate a highly magnetic portion, consisting mainly of free, but also containing locked, magnetite particles. The cobber tailing was then passed in two stages through a Franz isodynamic separator. The middle fraction was isolated, and, upon examination petrographically, was ascertained to be principally cummingtonite. The 100 to 150 mesh fraction of this sample was selected for the present study. It was cleaned by leaching briefly with hot, dilute HC1 and then by rinsing repeatedly with demineralized water. A ground and elutriated fraction of -5p cummingtonite was used for the electrophoretic measurements.

Jan 1, 1961

C. W. WASHBURNE; New York; N. Y. (communication to the Secretary *).-It has long been known that sulphur and oxygen react upon crude oils, removing hydrogen and thereby creating unsaturated hydrocarbons which unite with each other, producing heavier forms. Dr. Rogers now finds that the percentage of sulphur in the oils of several fields in California is roughly proportional to the specific gravity of the oil. This additional proof is most welcome. It is rather surprising, , in that the impression had prevailed that practically all the reacting sulphur escaped from the oil as hydrogen sulphide, and did not remain in combination with the oil. It would be interesting to know what part of the sulphur-plotted by Dr. Rogers is in solution as free sulphur and hydrogen sulphide, and what part is, in more complex compounds, such as thiophanes, etc.

Jan 10, 1917

By W. C. Williamson, J. L. Shugert

DUST control is receiving considerable attention today by most companies as is evidenced by the many articles, papers, and books written on the subject. ~~~t of the larger mining companies have given this subject close study and have established standardized methods of control. W. C. WILLIAMSON and J. L. SHUGERT, Members AIME, are Assistant Ventilation Engineers, Anaconda Copper Mining Co., Butte, Mont. San Francisco Meeting, February 1949. TP 2705 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Jan. 17, 1949. Permissible Limits: The question of permissible dust limits has been considered by medical commit-ties and various national conferences. Dr. Lanza, of the Metropolitan Life Insurance Company, Dr. Le-roy U. Gardner, of the Saranac Laboratory for the study of Tuberculosis, and Dr. Pancoast, of the University of Pennsylvania, have been members of these committees. A statement included in reports of some of these committees is as follows: Concentrations to which the dust must be induced in order to be safe have not been absolutely determined. There is evidence that a concentration of more than five million particles per cubic foot of a highly siliceous dust is dangerous. Therefore, it may be stated that it is desirable to avoid counts of more than five million particles of dust containing free silica to a high percent in working places. Table I gives the safe limits adopted by several state industrial codes. Table I. Safe Limits of Dust Concentration Limit Million Particles State Per Cu Ft Cal~fornia Silica (less rhdn 10 pct) 50 Silica (10 pct to 50 pcr) 10 Sllica (more than 50 pct) 5 New York Frcc silica less than 10 pet by weight of rock formation 100 Frec silica more than 10 Pct by weight of rock formation 10 Oregon Silica (over 40 pct) 5 Silica (20 to 40 pct) 10 Silica (10 to 20 pet) 20 Wisconsin 15 million particles, under 10 nicrons in longest dimension per cu ft of air, when the quartz content of the dust is 35 pct, variations in free silica content will make proportional inverse changer in this standard Close attention to dust concentrations has been given to mining operations, since these operations are frequently carried on at considerable distances

Jan 1, 1951

By J. L. Shugert, W. C. Williamson

DUST control is receiving considerable attention today by most companies as is evidenced by the many articles, papers, and books written on the subject. ~~~t of the larger mining companies have given this subject close study and have established standardized methods of control. W. C. WILLIAMSON and J. L. SHUGERT, Members AIME, are Assistant Ventilation Engineers, Anaconda Copper Mining Co., Butte, Mont. San Francisco Meeting, February 1949. TP 2705 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Jan. 17, 1949. Permissible Limits: The question of permissible dust limits has been considered by medical commit-ties and various national conferences. Dr. Lanza, of the Metropolitan Life Insurance Company, Dr. Le-roy U. Gardner, of the Saranac Laboratory for the study of Tuberculosis, and Dr. Pancoast, of the University of Pennsylvania, have been members of these committees. A statement included in reports of some of these committees is as follows: Concentrations to which the dust must be induced in order to be safe have not been absolutely determined. There is evidence that a concentration of more than five million particles per cubic foot of a highly siliceous dust is dangerous. Therefore, it may be stated that it is desirable to avoid counts of more than five million particles of dust containing free silica to a high percent in working places. Table I gives the safe limits adopted by several state industrial codes. Table I. Safe Limits of Dust Concentration Limit Million Particles State Per Cu Ft Cal~fornia Silica (less rhdn 10 pct) 50 Silica (10 pct to 50 pcr) 10 Sllica (more than 50 pct) 5 New York Frcc silica less than 10 pet by weight of rock formation 100 Frec silica more than 10 Pct by weight of rock formation 10 Oregon Silica (over 40 pct) 5 Silica (20 to 40 pct) 10 Silica (10 to 20 pet) 20 Wisconsin 15 million particles, under 10 nicrons in longest dimension per cu ft of air, when the quartz content of the dust is 35 pct, variations in free silica content will make proportional inverse changer in this standard Close attention to dust concentrations has been given to mining operations, since these operations are frequently carried on at considerable distances

Jan 1, 1951

By H. A. Hoffman

Competition from an all-flotation plant, with demonstrated economies and efficiencies, plus a change in smelting contract and introduction of improved cyclones lead to conversion from gravity-flotation. Detailed descriptions are given of equipment installed and procedures used at St. Joseph Lead's Federal mill. Future plans include further quality control by instrumentation in all aspects of the mill operation. Also planned are improvements in materials handling systems. Competitive conditions will continue to dictate improvements and changes in the mill flowsheet. The advent of all-flotation mills in the Lead Belt was introduced by the Indian Creek mill in late 1953. This modern and efficient plant then became a pattern for the other mills in this area to re-evaluate their circuits in an effort to develop flowsheets that would improve operating conditions and metallurgy. The Indian Creek mill demonstrated that all-flotation would require considerably less operating and maintenance labor than the combination of tabling and flotation that was common in the Lead Belt at that time. Two significant changes occurred in recent years to allow all-flotation to be seriously considered in other Lead Belt mills. One was a change in the smelting contract which did not require gravity concentrate. Another was the development of cyclones which provided classification of the flotation feed in a very small space. Since the Federal mill was the largest concentrating plant in the Lead Belt it was felt that the greatest savings could be made by investigating the all-flotation possibilities at this mill. Interest was stimulated by the milling and ore dressing Depts. to determine if this mill would be converted without undue cost, provided the metallurgy could be improved. Accordingly, laboratory tests were initiated to learn what metallurgical benefit could be derived. Numerous tests were run which indicated that grinding to all-flotation would improve the tailing by as much as 0.02 pct Pb. This was quite significant when multiplied by the tonnage of ore treated. Projecting the added cost of power for extra grinding and flotation, and the additional flotation reagents required, plus additional new equipment that would have to be purchased, it would still add up to a considerable saving. The all-flotation mill would reduce man power by some 30 pct, and make a metallurgical improvement. Operating costs could be reduced bv 2$ per ton. The metallurgical improvement would amount to 4$ per ton, for a total of 6$ per ton of ore milled. An estimate of the cost of the conversion was set at $250,000. With the savings as estimated this could be paid off in about two years. On paper it therefore seemed attractive enough to justify a mill test. MILL TESTING One section of the Federal mill was made available for use as a separate test circuit. Cyclones and density controllers were borrowed from the Viburnum and Indian Creek mills. Denver flotation cells were obtained from the Desloge mill that was then shut down. Two 10-cell groups of Fagergren flotation machines, consisting of eight roughers and two cleaners in each bank, were segregated from the remainder of the plant. The 9x12-ft rod mill was continued as a primary grinding mill. The two 6%x12-ft mills on this section were converted from rods to balls, and the speed increased to 22.0 rpm. Cyclones were installed to close the circuit of these ball mills. The ground pulp from each of the ball mills was fed separately to its own bank of flotation cells so that two completely separated test circuits could be run in parallel. This test circuit operated on a three-shift basis from Dec. 22, 1959 to Mar. 21, 1960. The first few weeks were occupied in developing conditions for proper metallurgy and trouble-free operations. Results were rather erratic but as the ore dressing laboratory and the mill operators became more familiar with conditions they were able to obtain expected results, which could be duplicated day after day. The last five weeks of testing indicated the best results and are tabulated in Table I. During the first two weeks a Denver unit cell was used on No. 1 flotation circuit. Even though it recovered almost one half of

Jan 1, 1962

By A. B. Kinzel

Since the exposition of the behavior of certain iron alloys by Sykesl involving the existence of an austenite loop and the discovery of such a loop in the chrome-iron system by Bain,2 there has been much conjecture both on his part and on the part of metallurgists in general as to the exact shape and location of this loop. In previous work commercial steel has been used and the microscope has been employed to locate the critical points so that the position of the loop has been quite approximate. Numerous attempts have been made to measure the critical points of the carbon-free alloys but all of these for one reason or another have failed. A satisfactory method for studying these phenomena is presented here. MateRial The first difficulty in this study was to obtain pure chromium-iron alloys. This has been overcome by melting in a vacuum electrolytic iron and chromium analyzing 99.84 Cr, Fe and C. A pure magnesite crucible was used and the melt allowed to solidify in the crucible. A typical analysis is chromium, 10.10 per cent., carbon, 0.006 per cent., silicon and manganese nil. To overcome the problem presented by segregation, ingots were made into wire 0.04 in. in diameter. This was accomplished by hand-forging the ingots into rods, using an oxyhydrogen flame for heating, in order to avoid carbon. Subsequently the rods were swaged to wire, the heating being carried out in hydrogen. Thus local segregation was eliminated although differences in analysis between portions 50 ft. apart were noted. An electric-resistance method was first tried to determine the critical points, but due to the physical defects in the wire this failed. Bain had previously shown the presence or absence of critical points in a qualitative way by observing the sag in a catenary. The author has devised the following method which gives an accurate determination of the critical points from expansion-temperature curves of suspended wire, a special telescopic dilatometer being used for the purpose.

By Nelson Severinghaus

Mineral fillers have been defined as inert materials that are included in a composition for some useful purpose. Because this definition and the scope of this review are not specific-indeed, exceptions abound-accurate total statistics are unavailable. One source estimates the total production in the United States in 1979 at 11.3 Mt (12.5 million st) valued at $534 million, averaging $49.19 per ton. Included are a broad group of minerals-asbestos, barite, bentonite, ground limestone and dolomite, clays, diatomite, feldspar, micas, silica, talc. Additional references will be made to synthetic mineral-derived fillers such as aluminum hydrate, precipitated calcium carbonate, and pyrogenic and precipitated silicas and silicates. A section on related uses at the end of this chapter covers absorbents and filters. Mineral fillers can be included in compounds to accomplish a variety of final results. Hardness, brittleness, impact strength, compressive strength, softening point, fire resistance, surface texture, electrical conductivity, and a host of other physical characteristics may be modified by the inclusion of fillers. These effects are the result of properties of the fillers, including chemical activity, hardness, particle size, shape and distribution, surface structure, color, density, and refractive index. To facilitate an overview of the mineral filler industry, this chapter will review the general usage of fillers, the inherent characteristics that intensify their utilization, and similarly their manufactured characteristics. Major using industries will then be examined in detail. Specific information on deposits and processing for industrial minerals will be found in the appropriate commodity chapter. All of these same minerals have additional significant uses based on their chemical composition or other characteristics. References will be found in other use chapters and summarized in commodity chapters. The chart in Table 1, updated from the 4th edition of Industrial Minerals and Rocks, illustrates the major mineral fillers (both natural and manufactured) and their more important end uses. Use of Mineral Fillers Archaeologists have found that more than 5000 years ago, bitumen used for mortar and waterproofing contained mineral contaminants that acted as fillers. Since that time man has added mineral products to compounds to improve certain characteristics. Perhaps the most common objective of filler usage is reduction of cost of the end product. Certainly the inclusion of a filler that costs 2¢ per 0.45 kg (lb) will reduce the cost of a plastic product whose resin costs 50¢ per 0.45 kg (lb). But the decision to use a specific filler is not that simple. It may "soak up" binder, making a compound more viscous and perhaps preventing its flow into a mold as an injection molding compound, but similarly will give good anti-sag characteristics to putty, caulking compound, or undercoating. Fillers may be incorporated to modify: 1) Cost 2) Physical characteristics 3) Flow characteristics 4) Fire resistance 5) Density 6) Heat conductivity 7) Color or brightness and opacity 8) Hardness, brittleness, impact strength 9) Deformity, viscosity, softening point 10) Processing problems 11) Electrical conductivity 12) Surface texture 13) Thermal expansion characteristics 14) Abrasion resistance

Jan 1, 1983

By F. Weinberg

INTEREST is currently being directed toward grain boundary morphologies in zinc in terms of grain boundary facetingl and grain boundary energies.' Some years ago the present author attempted to measure grain boundary energies in 99.999 pct purity Zn as a function of boundary angle, using the standard procedure of measuring equilibrium angles of the boundary traces at triple points. This followed an investigation he carried out on preferential melting of |H (112) Fig. 1—Electron transmission micrograph of a stacking fault, grain boundary intersection in copper. GRAIN BOUNDARY STACKING FAULT Fig. 2—Schematic representation of the intersection of Fig. 1, indicating inclination angles 0 and trace angles $. specimens were prepared by the Bollman technique in an electrolyte of 70 pct methanol, 30 pct HNO3 main-tained at -30°C. The interfacial free energy of the high angle grain boundary and of the stacking fault is assumed to be thermodynamically equivalent to the corresponding in-terfacial tensions. In terms of the true dihedral angles & between the intersecting interfaces, the equilibrium of interfacial tensions in the direction parallel to the stacking fault yields: ysF = -ygb(cos F1+ cos ±cosF2) Here, ysF is the stacking fault free energy and ygb is the grain boundary free energy, assumed equal on both sides of the intersection. Forces acting normal to the grain boundary, of the form ??gb/?F,l are assumed negligible as the grain boundary remains straight for a considerable distance on either side of the intersection. The micrograph of Fig. 1 may actually consist of several closely spaced stacking faults on the same slip plane. The actual point of intersection between the grain boundary and the first stacking fault, and the equilibrium configuration of the intersection, should not be affected by the presence of the other faults, as

Jan 1, 1970