Search Documents

Prof. Frank H. Probert, dean of the College of Mining of the University of California, visited the mining areas in the devastated regions as a member of the Bureau of Mines committee, which is studying the problems presented in the rehabilitation of mines there. He says that the absolute destruction of the coal mines in the Pas de Calais section makes it-necessary to use either the Westphalia or the Saar valley coal. The Saar mines, however, produce a poor quality of coking coal: therefore, it will not be possible to operate blast furnaces very efficiently unless provision is made for the introduction of better coal. He believes

Jan 6, 1919

By F. G. Jones, R. D. Pehlke, H. E. Gardner

The solubility of nitrogen in liquid Fe-18 pct Cr-8 pct Ni-0. 7 to 2.3 pct A1 alloys has been measured up to the solubility limit for the formation of aluminum nitride in the temperature range 1600° to 1700°C uszng the Sieverts' method. The solubility of nitrogen in 18-8 stainless steel increases with increasing aluminum content. Based on a nitride composition, AlN, the standard free energy of formation of aluminum nitride from the elements dissolved in liquid 18-8 stainless-steel alloys has been determined to be: ?G° = -42,500 + 20. IT in the range from 1600° to 1700° C. EVANS and pehlke1 have measured the equilibrium conditions for the formation of aluminum nitride, AlN, in liquid Fe-A1 alloys. The present study extends that work to the more complex solvent, liquid 18 pct Cr-8 pct Ni (18-8) stainless steel. Recent work by Small and pehlke2 has dealt with the effect of fourth-element additions on the solubility of nitrogen in 18-8 base alloys. They found the effect of aluminum additions, up to 0.74 pct, on the solubility of nitrogen to be small. The present study covered the range from 0.74 to 2.28 pct aluminum, and by extending the composition range may be used to better define the effect of aluminum on the nitrogen solubility in these alloys. EXPERIMENTAL PROCEDURE The Sieverts' method was used to measure the equilibrium solubility of nitrogen gas in liquid 18-8 stainless steel alloys containing 0.74, 1.49, 1.93, and 2.28 pct Al. The solubility was measured as a function of the nitrogen gas pressure at temperatures of 1600°, 1650°, and 1700°C. The apparatus used is the same as described by Small and Pehlke.2 The 100-g melts were made from Ferrovac-E high-purity iron, Crucible Steel Co.; 99.95 pct Cr, Union Carbide Corp.; 99.9 pct Ni, International Nickel Co.; and 99.99+ pct Al, Aluminum Co. of America. The aluminum was charged at the bottom of the crucible, surrounded by nickel and iron. The chromium was packed into the interstices to minimize vapor transport of the aluminum during initial melting. The hot volume of the system, measured for each melt with argon, ranged from 45 to 55 standard cu cm with a temperature coefficient of —8 x 10-3 cu cm per °C. The melt temperature was measured with a Leeds and Northrup disappearing-filament type optical pyrometer sighted vertically downward on the center of the melt surface. The temperature calibration of the system by Small and pehlke2 was assumed. Two problems are involved in determining the solubility product of a solid, metal nitride phase in liquid iron alloys. These are: 1) establishing the point of departure from Henrian behavior at the solubility limit of the metal nitride phase; and 2) determining the composition of the solid nitride which is precipitated. Determination of the solubility product of AlN was made by admitting small amounts of nitrogen into the reaction bulb until the deviation from Sieverts' law was clearly evident in the form of a pressure halt. To obtain the solubility product at several temperatures during one run the following procedure was used: 1) add increments of nitrogen to determine the Sieverts' law line at the lowest desired temperature; 2) continue to add nitrogen to precipitate a small amount of the nitride phase; 3) increase the melt temperature 50°C to dissolve the precipitated nitride; 4) repeat step 2 until either a nitride formed or the system reached ambient pressure; if a nitride formed at 1650°C, the sequence was repeated at 1700°C. The composition of the precipitated phase was checked by an X-ray diffraction pattern obtained from powder scraped from the surface of the solidified 1.93 pct A1 melt. RESULTS AND DISCUSSlON Solubility Measurements. Fig. 1 is a typical nitrogen-absorption curve obtained from measurements on a 1.93 pct A1 alloy. Since the initial absorption of nitrogen follows Sieverts' law the nitrogen solubility is plotted as a function of the square root of the pressure of nitrogen gas in the reaction bulb. The results of the solubility measurements for all alloys studied are summarized in Table I. The slope of the Sieverts' law line for each alloy was determined. Since this is also the solubility of nitrogen at 1 atm pressure of nitrogen gas, the latter designation is used for the data. It should be noted. however, that in most cases the value lies above the solubility limit for AlN. Fig. 2 shows the effect of aluminum on the solubility of nitrogen at this reference pressure and as a function of melt temperature. The solid portions of the lines represent attainable solutions; the dashed regions lie above the limit for precipitation of AlN.

Jan 1, 1969

Dec. 2, American Mining Congress, annual membership meeting, University Club, New York. Dec. 2, Society for Applied Spectroscopy, Socony-Vacuum Training Center, New York City. Dec. 4-6, AIME, Electric Steel Furnace Conference, Hotel William Penn, Pittsburgh. Dee. 5, Atlanta Meeting of Southeast Section, AIME, Ansley Hotel, Atlanta. Dec. 7-10, American Institute of Chemical Engineers, annual meeting, Hotels Cleveland and Carter, Cleveland. Dec. 8, AIME, Arizona Section, all-day meeting, Tucson. Jan. 6, 1953, Society for Applied Spectroscopy, Socony-Vacuum Training Center, New- York City. Jan. 14, 1953, AIME Connecticut Section, Hammond Metallurgical Laboratory, Yale University, New Haven, Conn. Jan. 14-16, 19th Annual Meeting of Society of Photogrammetry, Shoreham Hotel, Washington, D. C.

Jan 1, 1952

By Kenneth Robertson

ALL, strangers visiting this district are struck with the peculiar manner in which the pig-iron is graded. There are eleven regular grades, besides which, when gray forge is ordered, one-half of Nos. 1 and 2 Mill are shipped. Occasionally there is another grade Known as Silver Mill, which is made so seldom that I cannot describe it, and have no sample to exhibit. Most of you have found it difficult to grade properly and uniformly under the simpler system which obtains elsewhere, and can consequently readily imagine the increased difficulty with us. Each furnace employs an " expert," and even with this precaution, the system is not conducive, at all times, to amicable relations between buyers and sellers. I am told that it was adopted at the time Southern irons were seeking a market; but it still remains, although the time has come when our iron is sought for and has obtained for itself a place in the markets of the country. The grades are as follows:

Jan 1, 1889

By Marsh S. Watson, Robert A. Howard

The effect of depth of formation penetration by casing perforations has been studied by means of an electrolytic model. It is found that the relative productivity of perforated casing is profoundly affected by the depth to which the formation is penetrated. The first in. of penetration i: of especial importance. A scaling equation which was shown to agree with experimental results at zero penetration is used to calculate the relative productivity of a waled down casing with scaled down perforations. INTRODUCTION In an earlier piper' the authors showed that the point sink representation of casing perforations is inade- quate. It was Pointed out at that time that while the electrolytic model results were a marked improvement over point-sink calculations, they still left a great deal to be desired in that the electrolytic model represented a case not realizable in practice, namely, a clean hole through the casing but undisturbed formation on the other side of the casing. Obviously, to be effective, the perforation must penetrate a finite distance into the producing formation. It was the purpose of the present investigation to find how the relative productivity of perforated casing varies with depth of penetration. The term "depth of penetration" as used in this paper refers to the distance which the perforation penetrates the producing formation. The amount of casing and cement penetrated is not taken into account, a fact which is discussed more fully later. The "casing radius," therefore, is to be interpreted as the radius of the boundary between cement and formation wall. in cases where the casing is not in contact with the formation wall. APPARATUS The electrolytic model experimental setup was identical with that described in the previous paper' except that the platinum electrodes were now allowed to project from the lucite cylinder by varying amounts. When fewer than eight electrodes were used, the unused ones were covered with a coat of insulating material to minimize disturbances to the current flow-lines. Comparison runs made with the unused electrodes uninsulated, however, showed that the values of Q/Q0 so obtained did not vary by more than the experimental error from the values obtained with the unused electrodes insulated RESULTS The variation of relative productivity* with perforation density is shown for various penetration depths from 0 to 4.03 in. in Fig. 1. It will be seen that even one in. of penetration into the formation results in a huge increase in the relative productivity. Moreover, as-the depth of penetration increases, it becomes less and less advantageous to use large perforation densities, 80 pel. cent of open hole productivity being obtained with only three 0.5-in. diameter holes per foot when the penetration is 4.03 in.

Jan 1, 1950

By N. G. W. Cook

The conventional cyclic system of deep-level mining by drilling and blasting gives rise to an inadequate degree of stope sorting when mining thin reefs. This results in poor utilization of the capital facilities of a mine in the form of shafts, haulages, airways, and associated equipment. Continuous and controlled removal of the thin gold-bearing portion of the reefs would permit better stope sorting and hence greater utilization of capital facilities. Results of experiments to develop hard-rock cutting machines for mining are reported and the benefits which could be derived from their use are discussed. Mining, from exploration through refining, is essentially a process of sorting in which the payable mineral, or metal, is progressively separated from the other constituents of the earth's crust with which it was originally associated. This takes place more distinctly at each step of the operation. What is it that determines the degree to which sorting should be carried out at each of the several steps comprising a whole mining operation? The formal answer is that degree of sorting at each step which results in the lowest overall cost for the complete separation. In practice, individual steps are chosen from those available in current technology, each of which effects a degree of sorting such that the quantity of material which must be sorted in the succeeding step is economically acceptable. It follows that any new technological development has repercussions throughout the whole mining operation and, more important, that the solution to excessive costs in any one step of the operation may lie not in improving the costly operation itself so much as in increasing the degree of sorting preceeding that operation. This concept, particularly in relation to deep-level mining of thin, tabular gold-bearing reefs in South Africa, is discussed here, and the most recent results achieved in the development of hard-rock cutting machines for stoping more selectively than is possible with explosives are presented. Deep-Level Mining Deep-level mining involves operations which are either not encountered, or are of only trivial importance, in near-surface mining. Near-surface, the major operations are those of rock breaking, transport, and milling. In deep-level mining, hoisting, environmental control, and strata control assume major importance. Some idea of the relative magnitude of these operations may be gained by comparing the separate amounts of energy which are required, or which must be controlled, to effect the various operations when, say, mining a tabular deposit 40 in. thick at 8000 ft below surface, Table 1. It is true that the costs of handling a given quantity of energy are not the same for each operation. Nevertheless, Table 1 does emphasize the fact that the operations of hoisting, strata control, and environmental control are of unique and major significance in deep-level mining. In particular, hoisting and environmental control place a heavy load on the reticulation system of the mine—the shafts, haulages, and airways. Typically, a new, deep gold mine with an annual revenue of about $35 million requires a total capital expenditure of about $140 million of which some $100 million is invested in developing and equipping this reticulation system. The ratio between annual turnover and capital invested of about one-quarter is exceptionally low, and it typifies the poor utilization of capital by the current technology of mining hard rock at depth. The average thickness of the reefs in the new South African goldfields varies from 10 to 30 in.,l and even in the thicker reefs the gold is often confined within a small fraction of the nominal thickness. Nevertheless, it is universal practice to mine these reefs at a stope width of about 40 in. or more, so that the quantity of rock broken in the stopes and hoisted out of the mine is between two and ten times the quantity of rock actually carrying a significant amount of gold. The reason for the adoption of such excessive stope widths is to be found in the method of rock breaking by drilling and blasting. The only free surface to which a blast hole can break is the stope face. It follows2 that each hole cannot have a burden in excess of the height of the free face if it is to break satisfactorily. To

Jan 1, 1971

Jan 1, 1902

By J. Steininger

The Hallimond tube flotation of sphalerite and pyrite with sulfhydryl collectors has been found to be inhibited near neutral pH in the presence of copper salts. Alkalimetric titration studies of the reactions between collector and activator indicate that this effect is apparently related to the formation of basic copper collector complexes. The conditions of formation of these compounds and their stability are in good agreement with the depression observed in flotation experiments. The general procedure employed in the flotation of zinc sulfide minerals requires activation of the mineral surface by heavy metal ions, usually copper, which react more easily than zinc with the common short-chain ionic sulfhydryl collectors.' Commercially, zinc flotation is carried out under alkaline conditions (pH 7 to 10.5), but small-scale experiments indicate that zinc sulfide minerals can also be activated and collected under acid conditions. Selectivity, however, becomes poor at low pH and undesirable materials such as pyrite, silicates and carbonates tend to report in the float. Several years ago, Wark and Sutherland~, measured the contact angles of air bubbles on copper-activated sphalerite immersed in various sulfhydryl collector solutions. When represented, as in Fig. 1, on pH-sodium cyanide diagrams, the results are characterized by 'islands' of non-contact near neutral pH and

Jan 1, 1969

By C. F. Frey, P. J. Ahern, J. F. Wallace

THE high affinity of molten titanium for oxygen and nitrogen has resulted in considerable difficulty in developing a satisfactory melting procedure. It has been found necessary to perform melting operations either in a vacuum or inert atmos-phere, and failure to obtain a satisfactory crucible material has necessitated the use of special melting techniques. These techniques have included cold-mold arc-melting utilizing both consumable and nonconsumable electrodes, skull-melting, drip-melting, and levitation melting.' It has been recognized generally that the melting of both titanium sponge and titanium scrap would be expedited by the use of induction-melting procedures but the lack of a crucible capable of containing molten titanium without objectionable contamination thus far has prevented the use of induction-melting procedures. An extensive investigation: which included the common refractory materials was not successful in developing a satisfactory crucible for induction-melting. Some success in induction-melting has been attained with the use of a graphite crucible material, but in all instances sufficient carbon contamination was encountered to cause an appreciable reduction in the optimum mechanical properties of the titanium or titanium alloys. These investigations"" report an increase in the carbon content from approximately 0.3 to 1.0 pct. A serious reduction in the tensile and forming properties has been observed as a result of this carbon contamination. The development of a satisfactory induction-melting procedure for titanium without undue contamination undoubtedly would have considerable economic significance. Such a process would be particularly useful in melting the large quantities of low-cost scrap now available that can only be reprocessed at considerable expense and difficulty by the more elaborate techniques referred to previously. In addition, the process could provide a satisfactory method of melting and alloying of bri-quetted sponge for forging ingots.

Jan 1, 1959

Meeting of Mar. 27, 1914.-President Thayer announced the appointment of H. S. Munroe as a member and E. Gybbon Spilsbury as Chairman of the Library Committee of the Institute. The President announced the appointment of the Committee on Papers and Publications, the Technical Committees, the Committee on Increase of Membership, and the Committee on Junior Members and Affiliated Student Societies. The President announced the appointment of Dr. George F. Kunz as a member of the Reception Committee of the International Engineering Congress, 1915. It was voted that the Institute accept the invitation of the Mining and Scientific Press to occupy space at the Panama-Pacific Exposition next to them and avail itself of the service of their representative to receive and register members of the Institute who visit this space during the exposition.

Jan 5, 1914

By L. F. Marek, G. W. King, A. Bogrow

THE purpose of this paper is to present the data and some interpretation of the results of a laboratory study of the reduction of iron ore and the deposition of carbon from the reducing gas mixtures in such reductions. One major object of the study was to determine the effect of gas pressures on these chemical processes. Effort was made to approximate the conditions of temperature, gas composition, linear and mass gas velocities, pressure range, and extent of reduction prevailing in commercial blast furnaces. The results show that the reduction of Fe203 proceeds by two steps, largely consecutive under the conditions used herein: reduction of Fe203 to FeO, and reduction Of FeO to Fe. Unless the gas has a CO/CO2 ratio greater than 2.1 only the first step occurs under these conditions (850°C) but the following generalizations apply to either step or to the combination. The rate of reduction of relatively fine ore particles at any time is proportional to the mass rate of supply of CO (provided some of it is thermodynamically available) the rate therefore is proportional to the linear velocity at constant pressure, or to the pressure at constant linear velocity. Thus, the rate of reduction may be increased without increase in linear velocity f the reducing gas by increasing the mass velocity of the gas and increasing the pressure correspondingly to avoid any increase in the linear velocity. The rate "constants"-i.e., the efficiency of conversion of the "available" CO supplied-is not actually constant but decreases as the reduction proceeds, and is a function only of the state of the ore; i.e., of the amount of reduction already accomplished and hence of the amount of CO passed. The particle size Of ore used in nearly all the experiments was relatively small (8 to 14-mesh). The rate of reduction in run 16 with 3 to 8-mesh ore particles is within experimental error the same as with the finer ore. Although this would indicate an absence of effect due to particle size in this range of ore particles, it is desirable to have more data on other ore sizes and on ore of different densities before arriving at any generalizations on this point. Although it is possible to extend the analysis of these results to consideration of the more detailed kinetics and mechanism of iron oxide reduction, such extension is beyond the scope of the present paper. From the experiments on carbon deposition, it was evident that if carbon deposition is increased at all by the application of pressures up to 10 psi ga., such increase appears to be less than the experimental and analytical error. It appears safe to conclude that at top pressures on the order

Jan 1, 1947

By Albert Wiggin

THE copper-bearing sulphide ores from the mines in Butte, Mont., which are for the most part concentrated at the Boston & Montana duction Works in Great Falls and at the Washoe Reduction Works in Anaconda, contain the following minerals of economic value: Chalcocite, Cu2S; enargite, Cu3AsS4; cupriferous pyrite; bornite, Cu3FeS3; covellite, CUS; tetrahedrite, 4 CuS2Sb2S3; and tennantite, Cu8AsS7;. All of the ores carry a high percentage of pyrite. Many of the above sulphides are argentiferous and also carry from 10 to 20 cts. per ton in gold. The gangue is quartz and highly altered granite, with sphalerite and galena and more rarely barite and hubnerite as accessory minerals. An average chemical analysis of the second-class ore concentrated at Great Falls and Anaconda would be as follows: Copper 3.2 to 3.4 per cent. Silver 2. 3 to 3.0 oz. per ton. Gold 0.0-1 to 0.15 oz. per ton. Si02.. 55 to 60 per cent. FeO 12 to 15 per cent.. Sulphur 12 to 1.5 per cent. Al2O3, S to 10 per cent. CaO 0.5 to 0.8 percent. As203, 0.5 to 0.6 percent. Lead 0.2 to 0.3 percent. Before describing the Great Falls flow sleet as installed, at Anaconda, a brief history of the Great Falls concentrator will be given, including a description of the various concentrating machines and systems which have been tested in the search for a flow sheet which would give a higher recovery of copper.

Jan 8, 1913

Jan 1, 1944

By G. Ansel, J. O. Betteron

THE PURPOSE OF THIS PAPER is to give a brief picture of present day magnesium rolling practice, to elaborate on laboratory and development rolling experiments; and finally, to discuss the possible Future rolling of magnesium. The present production practice is so varied between various mills that it can only he concluded that no single producer is now using a process that is outstandingly superior to others. In view of this, only the general features of present day production practice have been presented and attention is focussed on the results of laboratory find development rolling of magnesium-base alloys as indications of the Future trend of magnesium rolling. MAGNESIUM ROLLING LITERATURE The literature relating to magnesium rolling is divided into three groups: the deformation mechanisms of the hexagonal magnesium crystals, the metallurgical aspects and laboratory type experiments in rolling, and finally, the articles on production rolling methods. This literature was reviewed and is summarized below. In the first group of references, the existence of basal slip in magnesium single crystals was shown by Schiebold and Siebel1 and of {102} twinning by Mathewson and Phillips2, Schmid3 predicted and partially established {101} slip at hot working temperatures. Bakarian and Mathewson4 confirmed the above and eliminated {101} twinning as a probable deformation mechan-

Jan 1, 1948

By Chandler Morse

RENEWABLE VS. NONRENEWABLE NATURAL RESOURCES Nonrenewable resources, such as minerals, are the inevitable center of attention in discussions of depletion and exhaustion. Nevertheless, it may well be proper to regard some nonrenewable resources as not subject to exhaustion, and renewable resources may sometimes be treated as if they were finite stocks. Thus, the availability of nonrenewable resources is not and probably never will be known completely Chap. 2.5A, and therefore is not subject to firm predictions concerning exhaustibility. Moreover, because exploration and discovery are more or less continuous processes it is often appropriate to regard mineral supplies as flows, and to treat the estimated reserves as working capital, an inventory, continually depleted by use and augmented by discoveries.23 The aggregate economically exploitable stocks of a given mineral are seldom estimated (or estimatable) with precision, as Chap. 2.5A shows, and even when they are, forecasts concerning years of remaining life can be and often are falsified by changes in one or more of the multidimensional conditions of supply and demand; or the productive services formerly derived from an exhausted stock may continue to provided without material impairment by one or more substitutes b Conversely, the renewable resources are all subject to depletion when the rate of use exceeds the natural or induced rate of replenishment, and cases of exhaustion or near exhaustion, as through soil erosion, overcuttmg of forest lands, and overfishing, are rather common c Where exhaustion is a clear possibility the resource may either be exploited on a consciously adopted "sustainable yield" basis or be treated as an exhausting asset." In some cases, conscious treatment

Jan 1, 1976

By W. C. Phalen

INTRODUCTION NOBODY will dispute the fact that the conservation in every legitimate manner of our valuable high-grade phosphate-rock deposits is a present-day problem of importance. The table and curve, given herewith, show. that during the past 10 years the exportation of high-grade rock has averaged very close to half the total output of the entire country. The bulk of this exportation is from Florida, for obvious reasons. It is plain that the deposits in this State, more particularly, are being wastefully depleted under a system of selecting the cream of the product for exportation to Europe, leaving the comparatively low-grade rock, running from 65 to 70 per cent., and under, in bone phosphate of lime, for our own n fertilizer manufacturers to work up when all the best rock is gone. In this paper the writer has endeavored to make a point of describing in some detail the important methods of production and conservation in Tennessee. These ought to prove of educational value to our American agriculturists and fertilizer manufacturers, and should result in a demand for the highest-grade rock, both for direct application to the soil and for use in making acid phosphate. It is certainly evident that the European

Jan 10, 1916

By J. M. Mutmansky, Y. J. Wang, H. L. Hartman

Procedures for determining the operating point that results when a fan is connected to a mine and placed in operation have been a source of confusion for decades. A variety of techniques have been proposed, often to the detriment of the practicing ventilation engineer trying to apply the techniques to the many mine/fan matching problems encountered in the engineering of mine ventilation systems. This paper proposes some different assumptions and definitions that simplify the problems in determining the operating point. As a result, a set of procedures is provided for determining the operating point of a mine/fan system when the outlet areas of the mine and fan are known. To simplify the development of procedures for determining the operating point for a mine/fan combination, the authors suggest that the mine pressures be redefined and then used in such a manner that the conservation of energy is ensured. This provides the basis for the recommendation that the fan operating point be determined using the fan total pressure and the system total pressure characteristics. This procedure can be applied to fans in the blower, booster, and exhaust positions equally well, and to both single-fan and multiple-fan networks. Another advantage is that the method is applicable to fans with or without an evase.

Jan 1, 1986

By W. H. Emmons

This paper is the third of a series treating of the relations of ores of the metals to igneous rocks. The first' outlined the general problem; the second2 proposed a classification of lode ores, and showed how the distribution of the deposits is in a certain measure controlled by the contour of the roof of the parent batholith. A number of mining districts were discussed, the examples being selected chiefly from group 2 of the classification. The proposed classification of lode deposits, briefly stated, is as follows: 1. Cryptobatholithic: near hidden batholiths which have not yet been exhumed by erosion. 2. Acrobatholithic: in and near cupolas or domes of batholiths—the high points of larger underlying masses. 3. Epibatholithic: on batholiths, near their rims, but below eroded cupolas, or below the highest points of the roofs. 4. Embatholithic: among closely-spaced outcrops which probably are parts of a single bathohth. The outcrops of invaded rocks predominate. 5. Endobatholithic. in and near roof pendants of large batholiths. The invading rocks predominate. 6. Hypobatholithic: in deeply-eroded batholiths, where even roof pendants have been eroded. Deposits of certain metals on the roofs of the batholiths are much more numerous in some positions than deposits of other metals, and the horizontal zonal arrangements of lodes of different metals are shown characteristically only in certain groups. In a large measure, also, the character of the fracturing and metallization is determined by the position on the roof of the batholith. The disseminated copper ores in porphyry constitute a clearly-defined type. All the deposits of these ores, as far as known, are in group 2. They appear to have been formed only in and around small upward projections of the parent granitic masses, and not low on the walls of the

Jan 1, 1927

By R. M. Brick

THE etched microstructures of cold-worked alpha brasses, after reduc-tions in excess of about 20 per cent, exhibit dark lines or markings, which have been termed "deformation bands," "etch bands," and "strain markings." The terms will be used synonomously in this report. The markings are similar in their general appearance to etch figures found in cold-worked iron, aluminum and other cubic metals but in certain respects may differ noticeably. At reductions of from about 20 to 50 per cent in brass, they appear as straight dark lines of irregular spacing and at random directions in different grains, but apparently intimately associated with definite crystallographic planes, usually {111}, in each crystal. At higher reductions, the markings on the rolling plane tend to appear in a direction transverse to the rolling direction in all crystals but may bend away at considerable angles, particularly near grain boundaries. Samans,1 on the basis of X-ray and micrographic studies of two single crystals of brass, rolled to a 50 per cent reduction, showed that the lines of deformation were the edges of thin mechanical twins parallel to octahedral planes. Barrett and Levenson2-4 have made comprehensive studies of the deformation of iron and of aluminum. They show that in these two metals the deformation markings originate by division of the original homogeneous crystal into banded areas differing in orientation by an amount that increases with the degree of deformation. The markings thus cannot be twin bands, and Barrett, in a review of this subject,2 attributed Samans' results on brass to an accidental choice of deformation that left the bands in approximately a twinned relationship. On the other hand, Mathewson5 has suggested that in some cases mechanical twinning offers a better rationalization of the coverage of some (111) pole figures of worked brass than the assumption of band rotation into sym-metry positions. Considering next a deformed and annealed alpha brass, the most striking aspect of its microstructure is the multiplicity of twin bands.

Jan 1, 1940

By L. B. McConville

The general term "tar sand" refers to sand that contains varying amounts of dense, viscous petroleum. Tar sand deposits have been found throughout the world, often in the same geographical area as conventional petroleum. The largest one by far is known as the Athabasca Tar Sands, in the province of Alberta, Canada. Actually a group of three deposits, these particular sands underlie an aggregate area of more than 12,000 sq miles. Current estimates place the contained raw petroleum at about 700 billion bbl; and via currently available technology, the amount of recoverable synthetic oil may be as much as 300 billion bbl-which is roughly equivalent to five times the combined US and Canadian total crude oil reserves. With the ever-widening gap between energy supply and demand, mining and petroleum companies are now evaluating all possible energy resources-both developed and underdeveloped-and, certainly, the Athabasca Tar Sand deposit is one of the more important ones to merit such attention. The first section in ME deals with the geology and historical developments; the other four sections, with mining methods, extraction technology, economics, and outlook.

Jan 1, 1975