Search Documents

By A. W. Schlechten, R. F. Doelling

Parkes' process crusts were vacuum distilled using a shortened Pidgeon retort. Zinc was effectively removed below 800°C and recovered as a zinc sheet easily stripped from the furnace liner. Lead dasdistillationazinc required about 950°C and the resulting lead condensate tillationtended to stick to the thin metal liner. Final purity of residue is limited only by nonvolatile metals such as copper. THE successful commercial application of vacuum distillation for the removal of zinc from lead, as described by W. T. Isbell,' raises the question of whether or not a similar method can be used for other metal separations. Preliminary laboratory experiments on the vacuum distillation of Parkes' crusts by one of the authors' gave such encouraging results that it was decided to make a series of tests with large scale equipment to determine the results that might be expected in plant operation. The pilot-plant test results are reported in this paper. The great advantages of vacuum dezincing are its simplicity, the relatively low temperature of operation, and the fact that the zinc is recovered in the metallic state ready for use again in the desilveriza-tion of lead bullion. These same advantages and others would be realized from the vacuum distillation of the zinc-lead-silver crusts made in the Parkes' process. Zinc readily will distill over at temperatures of 800" to 900 °C as contrasted with the 1200°C or more used in the Faber du Faur furnace. Furthermore, the recovery of zinc as metal is practically perfect since there is no loss by oxidation or fuming. If the vacuum distillation is continued and hastened by raising the temperature to around 1000°C, the lead will distill over at an appreciable rate and deposit in a warmer zone of the condenser. This lead will contain a small amount of silver, but it can be returned to the desilverizing kettles and there is not the chance of loss that there is in disposing of the rich litharge from cupelling. The lower temperatures required will mean a saving of fuel and less wear on the equipment. One further point is that the vacuum distillation could be run on a small scale practically continuously, so as to avoid the accumulation of large amounts of silver-rich material and the need of assembling a large crew for special cupellation runs. It should be pointed out here that the final purity of the silver residue will depend on the copper or iron content of the crusts, as these and other metals with low vapor pressure will not be eliminated. The idea of treating the silver-zinc-lead crusts from the desilverization of lead bullion by vacuum distillation is not a new one, but such experiments have not been reported, as far as can be determined. In 1912, T. Turner presented a paper3 before the Institute of Metals on the vacuum distillation of brass, and a member of the audience suggested that he try his method on Parkes' crusts. In 1935, W. J. Kroll, noted for his discovery of debismuthiz-ing lead by calcium additions, published a paper' on vacuum distillation of metals and pointed out possible applications in the lead industry. Principles of Separation The successful separation of two or more metals by distillation depends upon an appreciable difference in the effective vapor pressures of the metals in the alloy to be treated. The vapor pressures of the common metals have been determined with considerable accuracy; for example, at 800°C the vapor pressures of the individual metals which are of particular interest in this paper are about .as follows: Zn, 241 mm; Pb, 0.0553 mm; and Ag, 0.0000276 mm. Unfortunately,, data are not available on the activities of the components in the ternary system Zn-Pb-Ag, but it can be estimated that on the basis of the vapor pressures of the individual metals a good separation can be made by distillation. The preliminary laboratory tests previously mentioned' supported this assumption. The pilot-plant size vacuum distilling furnace is shown in Fig. 1. It consisted of an abbreviated Pidgeon retort, 5 ft long with an ID of 8 in., heated by six silicon carbide elements placed symmetrically

Jan 1, 1952

By Stanley Herold

Considerable interest has been shown, during recent years, in the possibilities of developing oil fields in the South American Republics, now that the exhaustion of our present fields can be seen in the not very distant future. The demand for fuel oil and its products has been increasing far more rapidly than our increment of production during the last few years. Increase of consumption has been largely curtailed by the lack of sufficient supply. The main factors that have contributed to our previous neglect of the southern fields have been as follows:, (a) Lack of sufficient demand for the product. (b) Competition with producing fields, having large production, low cost, and better geographical position, such as Tampico, Mexico. (c) Greater interest in home fields with ready market at hand. (d) Our ignorance of southern economic and geologic conditions, clue to the distance between those areas and our financial centers. (e) Economic conditions in the southern countries, necessitating high costs of exploration and exploitation of the fields.

Jan 9, 1918

By Paul M. Tyler

HISTORICAL concepts of the economics of the glass-sand industry are changing rapidly. The greatly expanded demand for glass containers combined with higher freight rates on raw materials and manufactured products have induced a migration of glass factories toward densely populated centers and the creation of new standards of place value for sub- standard sand deposits. This migration has been facilitated by the construction of pipelines to bring cheaper natural gas and liquid fuel to large cities and may be further speeded by the adoption of modern mineral dressing methods to permit economical utilization of local raw materials. Our national resources of naturally high-grade 1 silica sand are abundant, but most of the best de- posits are situated so far from large centers of population that it now costs $3.00 to $5.00 a ton to carry the sand from the mine to the optimum site for a 1 factory making beverage bottles, scientific and electrical glassware, and miscellaneous blown and pressed ware for local markets. It follows that on the basis of freight savings alone it may be economical to use material from inferior deposits closer to the factory even though the f.o.b. cost of mining and treatment may be much high

Jan 1, 1950

By Robert L. Slobod

In much of the work reported in the literature on long cores. true connate water value, probably have not been obtained because of insufficient flow of 011 to attain equilibrium. A -.satisfactory method for establishing connate water in long cores has been developed in which oil flow is maintained until no additiona1 water is displaced. INTRODUCTION Long cores have been used by sev-erals investigators in an effort to evaluate the efficiency of oil recovery for various producing schemes. The effects of many variables such as rate of displacement. pressure drop, volume of displacing medium, gas-oil ratio, inter-facial tension, and others have been investigated, and the merits of gas drive have been compared with water drive. In the older experiments no connate water was used. but in the more recent stndies the philosophy of the experiment calls for a core containing oil and connate water (irreducible water) as the starting point of the experiment. The method generally used to establish this condition in long cores involves dynamic' displacement wherein one or more phases are forced through the core. flow being maintained at a constant rate or at a constant pressure until a steady state is reached wherein there is no change of saturation with time. It is one purpose of this paper to point out that in much of the work reported in the literature true connate water values probably have not been obtained. The reason for this failure is pointed out. and a method for obtaining more reliable connate water values on long cores is presented. It is impossible at this time to completely evaluate the effect on the conclusions in the earlier papers resulting from the failure to obtain true connate water in the long cores, but some data are presented which indicate that serious errors may he present in many cases. MATERIALS AND APPARATUS Cores cut front outcrop sandstones (Strawn. Torpedo, and Elgin sandstones) with permeabilities of the order of 300 md were used. The major experiments were made with a core 18-in. long and 2-in. in diameter. Cores of the same diameter but only 12-in. long were used in a few tests? and in some work a core I-in. in diameter and 11-in. long was used. These materials were all somewhat bentonitic. 'To reduce the effect of such constituents, one of the cores (Torpedo No. 10) on which the most work was performed was acid extracted at the start of the experiment. Brine containing 50,000 ppm chloride and naphtha (Stoddard's Solvent) were used as the water and oil phases, respectively. The core was mounted in a rubber sleeve which forms the inner lining of a brass cylinder. In this arrangement2 the rubber sleeve is forced against the core by applying pressure to water in the annular space between the rubber sleeve and the brass cylinder wall. The core is therefore sealed in rubber so that all fluids introduced at the input end of the core flow through the core. With this equipment the core may be easily removed for inspection and analysis. Also, other cores may be introduced for study with no extra time for preparation such as is required when plastic mounting is used. When pressure or conductivity measurements are desired at intermediate points along tile length of the core, the brass cylinder comprising the outer jacket of the core holder is cut into section, of the desired length. Each section is then made up as an individual unit with its own rubber sleeve (see Fig. 1). The individual units are then butted up against a ring of plastic or other insulating material which carries an electrical contact for resistivity measurements and an opening which can be used for the measurements of fluid pressures. The individual units are forced tightly against the plastic ring separators and held in place with several tie rods. Inlet and outlet end butts of the same diameter as the core and several inches in length are provided to control the introduction and withdrawal of fluids and to complete the arrangement for sealing the core within the rubber sleeve. Fluid flow is maintained either by applying pressure to the liquid confined in a reservoir or by the use of a gear pump. The latter is preferable where continuous flow at a moderate rate over a long time interval is desired since a small volume of liquid can be readily recirculated using filters to prevent plugging of the core. EXPERIMENTAL The oven-dried core is weighed and is then completely saturated with brine

Jan 1, 1950

By AIME AIME

THE 129th meeting of the American Institute of Mining and Metallurgical Engineers convened at New York City, in the Engineering Societies Building, Feb. 18-20, 1924. On February 21 an excursion was made to the Bethlehem Steel Co., at Bethlehem, where about 200 members and guests were splendidly entertained. An illustrated description of the Bethlehem Plant will be published next month. The meeting and excursion were largely attended; the registration at New York totalled 1276 versus 1201 in 1923. William Kelly, long identified with the iron-mining industry of the Lake Superior district, was elected President of the A. I. M. E. for the coming year, at ,the annual business meeting, Feb. 19, succeeding E. P. Mathewson. The following Directors were also elected (the date signifies year of termination of office; the final figure indicates the "District" the Director represents).

Jan 1, 1924

By AIME AIME

THE meeting of the Petroleum Division at Houston, Oct. 10-12-headquarters, Rice Hotel-was preeminently a technological success. Two hundred and twenty-five attended the Thursday morning session and approximately 200 attended the sessions on Thursday and Friday afternoons and Saturday morning. Harry Power, Chairman of the Division, in his opening remarks, credited Paul Weaver and M. Albertson, respectively chairman and vice-chairman of the local committee, with working long and prodigiously in organizing the program. The theme of the initial session was indicated by Mr. Albertson in a statement relative to the estimation of developed petroleum reserves. He said that the problem of securing more accurate estimates of developed petroleum reserves existed prior to curtailment of production. With curtailment, however, the problem became an acute one. Mr. Albertson gave some of the more important reasons for this situation. Since the decline-curve method became inapplicable, the volumetric method has become the chief one used. It depends on the factors of productive formation volume, porosity, saturation, and recovery. He briefly discussed the factors necessary for application of the volumetric method. P. P. Gregory discussed the estimation of petroleum reserves in prorated lime¬stone fields (see his paper in the October

Jan 1, 1935

By Stanley F. French, Bruno F. Koch

Although the amount of dust that will be actually recovered in the six main dust-control systems cannot be accurately stated until the tests mentioned previously are carried out, it is estimated that the average air entering the wet collectors will contain around 5 grains of dust particles per cubic foot. This means that the six systems handling a total of about 133,000 cu.ft. of air per minute will return about 68 1/2 tons of dust to the concentrator per day and since the copper in this dust will average around 2 per cent, the total recovery is approximately 1.37 tons of copper every 24 hours. This important copper recovery is not due entirely to the dust-control system since in a plant without control only the duct that is dispersed to the atmosphere represents a loss. A conservative estimate of the recovery of copper solely due to the dust control system would be about half of the total or approximately 0.70 tons of copper per day.

Jan 1, 1942

By E. Swartzman, G. C. Behnke

THE free-swelling index, a numerical value for the free-swelling properties of coal, is being used to an increasing extent in specifying coal for burning in various types of equipment. The empirical standard ASTM method for determining this index uses, as a source of heat, a gas burner which requires frequent calibration because gas pressures are not constant, relatively small changes in gas pressure resulting in rather wide variations in the temperature attained in a crucible and thus in the resultant size of the coke button. Furthermore, the quartz crucibles specified for the test are not standard equipment, and relatively small variations in dimension and wall thickness from those specified often result in rather wide variations in the resultant size of the button. A method of analysis to be satisfactory not only for a scientific laboratory but also for use in industrial control laboratories under varying conditions should employ equipment which is rugged, easily calibrated, and readily replaceable by standard materials. Gas is not universally available as is electricity, and it is generally easier to calibrate and control a simple electric furnace or heater than a gas burner, the voltage not usually fluctuating to the degree that gas pressure does. Quartz crucibles are fragile, and the size specified in the test is not normally used for any other purpose in the laboratory. Although more expensive, the 15-cc platinum crucible, available in all laboratories where volatile matter in coal is determined by the standard ASTM method, is sturdy and standard and easily replaced. Because of these considerations, a modification of the standard method has been developed which employs a standard laboratory 350-w cone heater and standard 15-cc platinum crucibles. The results of numerous tests conducted with such apparatus show conclusively that the free-swelling index values as judged by the buttons produced with this equipment are exactly the same as those obtained by the standard gas burner method. Thus it is suggested that this electric cone heater method employing standard 15-cc platinum crucibles be considered as an alternative to the ASTM method, Designation: D720-46. The free-swelling index of coal is determined by means of the ASTM method, D720-46. This method, which is an adaptation of the crucible swelling test for coal of the British Standards Institution, consists of heating 1 g of coal in a special covered quartz crucible in a regulated gas flame for a period of not less than 2.5 min in which time the temperature of the inner surface of the bottom of the crucible reaches a temperature of 82025°C. The residual coke button is then compared in size and shape with a series of standard profiles shown in Fig. 1 and designated by number from 1 to 9 in increasing order of size. As the method is empirical, it requires rigid standardization of the apparatus and repeated calibration of the gas burner. The dimensions of the low form quartz crucible recommended must be rigidly adhered to as small variations in diameter or wall thickness result in variations in the rate of heat transmission and thus in the resultant size and shape of the coke button. The gas burner must be calibrated almost every time a new set of determina-

Jan 1, 1952

By Arthur L. Bishop

INTRODUCTION Purpose The in-situ leach method for uranium extraction is a relatively new and innovative method of uranium mining. In 1975, the first commercial in-situ facility began operation in south Texas. Since that time numerous other operations have been initiated as either pilot or commercial ventures. Considerable literature has been published that deals primarily with generalities of the process or environmental concerns. Several federal agencies have published documents which do not reflect the true operating or environmental nature of the in-situ leach method of uranium extraction. From an environmental standpoint, this is also evident in the promulgation of rules and regulations. Hence, the purpose of this paper is to present experience with an environmental concern--non- production zone excursions--such that the industry and the regulatory agencies will gain greater insight devoid of preconceived ideas and misconceptions. General Process Description In south Texas, in-situ leach mining is utilized to extract uranium from permeable sandstone ore deposits 61 to 213 meters (200 to 700 feet) below the surface. Uranium is present as an insoluble uranium oxide. In the in-situ or solution mining technique, anoxidizing lixiviant is injected into the formation through injection wells. The solution reacts with the insol uble carbonate complex. This soluble uranium complex is produced at recovery wells, each containing a submersible pump. During production there is a constant sweeping of lixiviant through the formation from the injection wells to the recovery wells. Injection and recovery wells can be arranged in any of a number of geometric patterns dependent upon ore body configuration, aquifer permeability, and operator preference. Submersible pumps in the recovery wells pump the uranium rich pregnant solution to the initial processing facility. Monitor wells surrcsund the pattern area and are screened in appropriate stratigraphic horizons (production and non-production zones) to detect any lixiviant migration that may occur (Fig. 1).

Jan 1, 1980

NEW MEMBERS The following list comprises the names of those persons who became members during the period Aug. 10 to Sept. 10, 1914: Members ALLEY, HARRY MCCAMMON, Mill Foreman .... Churchill Mining Co., Wonder,2 Nev. AMBLER, J. OWEN, Met..; ... Calumet and Arizona Mining Co., Douglas, Ariz. ANDERSON, JAMES WILLOUGHBY, Duell, Warfield and Duell, 2 Rector St., New York, N. Y. ANTISELL, FRANK L., Asst. Supt Raritan Copper Works, Perth Amboy, N. J. CARRINGTON, FRANK GAMBLE, Sec'y and Asst. Mgr., Standard Foundry Co., Anniston, Ala. CONKEY, CHARLES ROLLAND, Structural Draftsman, Barnett McQueen Co., Ft. William, Ont., Canada. COOK, PAUL RICHARDSON, Mill Shift Boss, Buckhorn Mill and Cyanide Plant, Buckhorn. Nev.

Jan 10, 1914

By Clyde Evarts Weed

SOME one once affirmed his great belief in luck, adding that he had found that the harder he worked the more luck he had. Clyde Weed is a firm believer in this method of courting the fugitive lady. He is at work early and late, often leaving his staff at Anaconda's offices at 25 Broadway breathless trying to keep up with the ideas teeming from a fertile brain and the actions those ideas entail. Miles ahead of his assistants much of the time, he still manages to be an agreeable fellow to work with, no small accomplishment as many can testify. Mr. Weed arrived in the world at Moorestown, Mich., on Aug. 8, 1890. Sixteen years later he entered Michigan Agricultural College, a lowly freshman. The following year, with the experience and wisdom expected of a sophomore, he transferred his studies from the reaping of a harvest on the surface of the earth to delving into the deeper, unpredictable bowels of the earth, his studies now shifted to the Michigan College of Mines. Last June his alma mater conferred upon him the degree of Doctor of Engineering.

Jan 1, 1947

Fred. T. Greene, Rossland, B. C. (communication to the Secretary): At the beginning of his gaper, Mr. Herzig refers to an article of mine in the Engineering and Mining Journal of January 27, 1900. I would like to add that the method de-

Jan 1, 1901

By L. F. Bryant, J. P. Hirth, R. Speiser

The surface, gain boundary, and twin boundary energies, as well as the surface diffusion coefficient, of cobalt were determined from tests at 1354°C in pure hydrogen. A value of 1970 ergs per sq cm was calculated for the surface energy, using the zero creep method. It was possible to measure the creep strains at room temperature because the phase transformation was accompanied by negligible irreversible strain and no kinking. Established techniques based on interference microscopy were used to obtain values for the other three properties. The gain boundary and twin boundary energies were 650 ad 12.7 ergs per sq cm, respectively, while a value of 2.75 x l0 sq cm per sec was determined for the surface dufusion coefficient. In the course of a general study of cobalt and cobalt-base alloys, information was required about the surface energy of cobalt. Hence, the present program was undertaken to measure the interfacial free energy, or, briefly, the surface energy, of the solid-vapor interface of cobalt. The microcreep method was selected for this measurement because other surface properties could also be determined from the accompanying thermal grooving at grain boundaries and twin boundaries. A brief summary of the methods for determining the various surface properties follows. At very high temperatures and under applied stresses too small to initiate slip, small-diameter wires will change in length by the process of diffu-sional creep described by Herring.1 The wires acquire the familiar bamboo structure and increase or decrease in length in direct proportion to the net force on the specimen. For a specimen experiencing a zero creep rate, the applied load, wo, necessary to offset the effects of the surface energy, y,, and grain boundary energy, y b, is given by the relation: where r is the wire radius and n is the number of grains per unit length of wire. The first results obtained from wire specimens were reported by Udin, Shaler, and Wulff.' udin3 later corrected these results for the effect of grain boundary energy. The grain boundary energy is determined from measurements of the dihedral angle 8 of the groove which develops by thermal etching at the grain boundary-free surface junction. For an equilibrium configuration: Measurements of the angle 8 can be made on the creep specimens4'5 or on sheet material, as was done in this investigation by a method employing interference microscopy.= If the vapor pressure is low, the rate at which grain boundary grooves widen is determined primarily by surface diffusion and, to a lesser extent, by bulk diffusion. The surface diffusion coefficient, D,, is obtained from interferometric measurements of the groove width as a function of the annealing time, t. As predicted by Mullins~ and verified by experiment, the distance, w,, between the maxima of the humps formed on either side of the grain boundary increases in proportion to if grooving proceeds by surface diffusion alone. For this case: where fl is the atomic volume and n is the number of atoms per square centimeter of surface. When volume diffusion also contributes to the widening, the surface diffusion contribution can be extracted from the data by the method described by Mullins and shewmon.8 Where a pair of twin boundaries intersects a free surface, a groove with an included angle of A + B (using the groove figure and notations of Robertson and shewmong) forms by thermal etching at one twin boundary-free surface junction. If the "torque terms", i.e., the terms in the Herring10 equations describing the orientation dependence of the surface energy, are sufficiently large, an "inverted groove" with an included angle of 360 deg-A'-B' develops at the other intersection. The angles A + B and A' + B' are measured interferometrically. When the angle, , between the twinning plane and the macroscopic surface plane is near 90 deg, the twin boundary energy is calculated from the relation: 1) EXPERIMENTAL TECHNIQUES Five-mil-diam wire containing 56 parts per million impurities was used for making ten creep specimens. These specimens had about 15 mm gage lengths with appended loops of wire and carried loads (the specimen weight below the midpoint of the gage length) ranging from 3.7 to 149.8 mg. The wires were hung inside a can made from 99.6 pct pure cobalt sheet. Beneath the wires were placed small specimens of 20-mil-thick, 99.9982 pct pure cobalt sheet from which the relative twin boundary and grain boundary energies and the surface diffusion coefficient were measured. All the specimens were annealed at a temperature of 1354" i 3°C which is 92 pct of the absolute melting point of cobalt. The furnace atmosphere was 99.9 pct pure hydrogen that was purified further by a Deoxo catalytic unit, magnesium perchlorate, and a liquid-nitrogen cold trap. As a precautionary measure the gas was then passed through titanium alloy turnings which were heated to 280" to 420°C and replaced after every test period. The hydrogen was maintained at a

Jan 1, 1969

By J. R. Kyte, L. A. Rapoport, R. J. Stanclift, S. C. Stephan

Experimental studies covering a wide range of core materials and fluid properties have been conducted to determine the mechanism of oil displacement by water in a partially gas-saturated porous medium. In all instances, the presence of a gas phase was found to have a beneficial effect in reducing residual oil saturations. The practical significance of this benefit is discussed, and a simplified procedure is outlined for evaluating the effects of free gas on water flooding by means of short core tests. INTRODUCTION In addition to oil and water, reservoirs subjected to water flooding frequently contain, also, a gas phase. Common engineering procedures account for the presence of this "free gas" only from the viewpoint of volumetric balance, implying that the only role of the gas consists of providing "fill up" space. It is usually visualized that during the initial stages of the water invasion, the oil, moving ahead of the water, displaces part of the gas and that subsequently the remaining portion of the gas phase is totally compressed and dissolved in the advancing oil bank. Thus, consideration of a two-phase, water-oil flooding mechanism supplies an adequate basis for predictions of oil recovery if the pressure build-up caused by the flood is sufficiently great, so as to reduce the free gas saturation to a negligible value in any portion of the reservoir by the time that portion is reached by the advancing flood water. In many in- stances, however, waterflooding operations are carried out when the reservoir pressure is still relatively high SO that the pressure build-up associated with the water flood may not result in complete dissipation of the gas phase. Under such circumstances it is necessary to ascertain whether or not the presence of free gas has an effect on waterflood behavior and, if so, to account for any such effect in the evaluation of field operations. The difficulties encountered in attempting to arrive at a comprehensive picture of the displacement mechanism of oil by water in the presence of free gas stem from the fact that most of the published data on this subject were obtained under conditions that were either not clearly representative of those existing in a reservoir or not sufficiently controlled to permit evaluation of the effects specifically caused by the gas phase. Some of the most precise data found in the literature were obtained in tests using a "static" gas phase created prior to each water flood by circulating oil through partly gas-saturated cores until a "trapped," residual gas saturation was established throughout the system.' Other investigations were conducted under more representative conditions where the gas phase was free to move during the water flood: but in most cases the results of these tests were obscured by auxiliary phenomena which arise from the compressibility and solubility of the gas and preclude quantitative conclusions.2,3,4 Prior to water flooding, a reservoir usually contains oil and gas, distributed in a manner in which both are free to move. Thus, the principal objective of the present studies was to determine the type of displacement mechanism occurring when water invades a porous medium containing oil and a "mobile" gas phase. Further-

Jan 1, 1957

By T. S. Plaskett

A striated structure perpendicular to the growth axis was observed by the copper-decoration tech-nique in dislocation-free, .float-zoned silicon crystals. The striations, which were spaced about 100 p apart, fitted the relationship d = f/u , where d is the spacing, f is the growth rate, and u is the crystal rotation rate. Each stria was resolved into an UNDOPED silicon crystals pulled from quartz crucibles by the Czochralski technique usually exhibit a striated structure perpendicular to the growth axis.'-' This structure has been attributed to oxygen segregation, with the oxygen being introduced from the quartz crucible. If the crucible is rotated, the level of oxygen contamination has been reported as high as 10° atoms per cu cm.10 These striations are similar to solute striations commonly observed in doped Czochralski-grown crystals. The periodic nature of the striations is caused by a periodic variation in the growth rate",12 which is attributed mainly to thermal gradients in the melt.13 A finer striated structure14 attributed to constitutional supercooling is sometimes observed between the coarse striae. The oxygen striations have been observed by infrared transmission techniques,' by the copper-decoration technique,' by X-ray diffraction microscopy,6-8 and by 9 p absorption measurements3 on crystals pulled from the melt both with and without dislocations. In this investigation float-zoned dislocation-free crystals were examined by the copper-decoration technique. The level of oxygen for float-zone material is less than 1016 atoms per cu cm the lower limit of detection by 9 p absorption measurement. EXPERIMENTAL TECHNIQUE The crystals were grown by the float-zone process with the rf heating coil outside of the quartz envelope containing the silicon. All float zoning was done under an atmosphere of purified helium. The Dash technique15 was used to grow the crystal dislocation-free. This involves growing the crystal initially with a diameter between 2 and 3 mm and at array of starlike precipitates of copper. The strucLure was not .found at the surface tor a depth of about 1.5 mm, or in a region of similar width ahead of a dislocation network. The structure is postulated to consist of vacancy clusterings or dislocation loops. very rapid rates, about 20 mm per min, for a distance of about 3 cm. The diameter of the crystal is then increased to the diameter of the source of silicon, which in this case was about 19 mm. Because of the arrangement of the apparatus, the zone was passed downward rather than upward, contrary to the standard float-zoning practice. Also, the source was rotated rather than the seed. ziegler17 has made dislocation-free crystals by a similar technique but has passed the zone upwards. The starting material was zone-refined and had a p-type resistivity of 150 ohm-cm. The major impurity was boron; the total impurity excluding the boron was reported by the supplier (Dow-Corning) to be typically less than 2 x 1013 atoms per cu cm. The crystals were examined by the Dash copper-decoration technique18'19—a method in which about 10" atoms per cu cm of copper are diffused at a temperature between 900" and 1000°C into silicon which is then quenched to room temperature. On quenching, the copper precipitates on crystalline defects which are then visible when viewed by transmission infrared microscopy. The photomicrographs shown were taken either of the infrared image tube screen or directly on infrared film. All sections prior to decorating were chemically polished and, for some sections, given a sirtlZ0 dislocation etch-pit examination. After decorating, the samples were mechanically polished. RESULTS A photomicrograph, taken in transmission of a decorated cross section, is shown in Fig. 1. The portion of the section shown is near the surface of the crystal. The entire cross section showed no dislocation etch pits after being given a Sirtl etch treatment. It is seen that the copper precipitated randomly. Each precipitate, as has been reported by others, was found to have a starlike structure.

Jan 1, 1965

By William H. Spice

The area on which oil and gas development is reported covers 30 counties, which are included in the Texas Railroad Commission's District No. I. This area not only includes the old established Balcones fault-line group of producing fields but also includes the southwest extension of this trend and some of the deeper Wilcox (Eocene) exploratory development. (Fig. J.) In the old Balcones fault-line zone, three new fields were discovered during 1941. These fields are comparatively small, producing from Dale limestone or Austin chalk. No new fields were discovered during the year in the Edwards (Lower Cretaceous) limestone horizon. One new shallow field was discovered in the Reklaw (Eocene) sand horizon and, in the southwestern part of the district, one oil field and one gas field were discovered in the Navarro (Upper Cretaceous) sand horizon. An extremely important extension was made to the one producing Wilcox (Eocene) field of the district in the Washburn Ranch field of La Salle County. The district produced 6,650,357 bbl. during 1941, which was a 12 per cent decrease under production for 1940. Approximately 4,954,000 bbl. of this total production was produced by the three Edwards limestone fields, Luling, Salt Flat and Darst Creek, the remaining production coming from the other 43 active fields in the district. In all, 3694 wells were producing at the end of 1941, compared with 3559 wells at the end of the previous year. During the year, 139 new producing wells were completed and 29 wells were abandoned in the producing fields. The increase in producing wells represents an increase in new wells over abandonments in these fields, together with a decrease in wells temporarily shut down as of the end of 1941. The majority of production drilling was carried on in the following fields; Bee Creek, Chicon Lake, Elm Creek, Gas Ridge, Pearsall and Tenney Creek. Approximately 250 wells were drilled during 1941, of which 110 were exploratory wells completed as failures throughout the district. Considerable exploratory work was continued during 1941 along the Wilcox trend. Geophysical work employing various types of geophysical methods and leasing activity was continued along this trend, particularly by the major companies. The significance of this activity is apparent from the successful extension and development in the Washburn field of La Salle County, where several well-developed gas-and-oil producing horizons have been developed in the lower Wilcox section between 5100 and 5600 ft. as noted in the following paragraphs. Continued exploratory activity along this general trend as far as present conditions will permit is predicted for 1942. New Fields Elgin Field, Bastrop County.—No. I-A Hiram Walker, Marts and Beaven, Inc., discovery well of the Elgin field, was com pleted on Apr. 22, 1941, in broken Austin chalk from 2820 to 2840 ft., pumping 105 bbl. per day, 36.8°A.P.I. gravity. The well apparently is producing from a crevice in

Jan 1, 1942

By William H. Spice

The area on which oil and gas development is reported covers 30 counties, which are included in the Texas Railroad Commission's District No. I. This area not only includes the old established Balcones fault-line group of producing fields but also includes the southwest extension of this trend and some of the deeper Wilcox (Eocene) exploratory development. (Fig. J.) In the old Balcones fault-line zone, three new fields were discovered during 1941. These fields are comparatively small, producing from Dale limestone or Austin chalk. No new fields were discovered during the year in the Edwards (Lower Cretaceous) limestone horizon. One new shallow field was discovered in the Reklaw (Eocene) sand horizon and, in the southwestern part of the district, one oil field and one gas field were discovered in the Navarro (Upper Cretaceous) sand horizon. An extremely important extension was made to the one producing Wilcox (Eocene) field of the district in the Washburn Ranch field of La Salle County. The district produced 6,650,357 bbl. during 1941, which was a 12 per cent decrease under production for 1940. Approximately 4,954,000 bbl. of this total production was produced by the three Edwards limestone fields, Luling, Salt Flat and Darst Creek, the remaining production coming from the other 43 active fields in the district. In all, 3694 wells were producing at the end of 1941, compared with 3559 wells at the end of the previous year. During the year, 139 new producing wells were completed and 29 wells were abandoned in the producing fields. The increase in producing wells represents an increase in new wells over abandonments in these fields, together with a decrease in wells temporarily shut down as of the end of 1941. The majority of production drilling was carried on in the following fields; Bee Creek, Chicon Lake, Elm Creek, Gas Ridge, Pearsall and Tenney Creek. Approximately 250 wells were drilled during 1941, of which 110 were exploratory wells completed as failures throughout the district. Considerable exploratory work was continued during 1941 along the Wilcox trend. Geophysical work employing various types of geophysical methods and leasing activity was continued along this trend, particularly by the major companies. The significance of this activity is apparent from the successful extension and development in the Washburn field of La Salle County, where several well-developed gas-and-oil producing horizons have been developed in the lower Wilcox section between 5100 and 5600 ft. as noted in the following paragraphs. Continued exploratory activity along this general trend as far as present conditions will permit is predicted for 1942. New Fields Elgin Field, Bastrop County.—No. I-A Hiram Walker, Marts and Beaven, Inc., discovery well of the Elgin field, was com pleted on Apr. 22, 1941, in broken Austin chalk from 2820 to 2840 ft., pumping 105 bbl. per day, 36.8°A.P.I. gravity. The well apparently is producing from a crevice in

Jan 1, 1942

By ERIIL SCHROEDTER

THE death, on May 6, 1908, of Dr. Hermann Wedding, Privy Mining Councilor of the Kingdom of Prussia, and Professor of the Metallurgy of Iron and Steel at the Royal Mining Academy of Berlin, was a loss keenly felt by the whole metallurgical world. Not alone in his native land, but also in foreign countries did he enjoy an esteem of which the title of honorary membership in the American Institute of Mining Engineers, the United States Association of Charcoal Iron-Workers, and the (British) Iron and Steel Institute bears eloquent testimony. Hermann Wedding was born March 9, 1834, in Berlin. At the suggestion of Dr. C. J. B. Karsten, the veteran father of Prussian metallurgy and author of the first German text-book of the metallurgy of iron, lie turned his attention, after gradu¬ating from the gymnasium, to mining and metallurgy. In 1853, he began a practical course at the Malapane iron-works, in Upper Silesia. Subsequently, he studied at the Berlin Mining Academy, and received from the University in 1859 the degree of Doctor of Philosophy. A journey which be made to England, somewhat later, led to his undertaking a German translation, with revision and additions, of John Percy's classic treatise on the metallurgy of iron and steel, the publication of which, in successive installments, stretched through many years. In 1863, lie published, as a thesis in connection with his "Assessor's examination," an essay, entitled The Results of the Bessemer Process for the Production of Steel, and Its Prospects for the Rhenish and Westphalian Iron and Steel Industry, which revealed such ability and knowledge as to secure for him a call to the chair of metallurgy in the Berlin Mining Academy.

Jun 1, 1909

By AIME AIME

ENGINEERS in the past have been largely associated with private enterprise and there has been a considerable tendency on the part of some members of our profession to depreciate government service for engineers. We engineers must change our mental attitude about employment in government service, particularly in view of the present most friendly attitude of the U. S. Civil Service Commission toward engineers for major posts in our Government. We must also take a much more active interest in public affairs. It must be realized that the national-defense program, which we are now organizing, will require for its effectiveness large numbers of engineers skilled in a wide range of technical and administrative services. In fact, the success of this undertaking will depend largely upon the extent to which our Government can command expert engineering talent to serve during the emergency. There is an acute shortage of technical and supervisory engineering personnel not only in the industries concerned with national defense but also in the Army, Navy, and other defense agencies of the Government. By an Act of Congress, approved on Oct. 9. 1940. $9,000.- 000 was turned over to the U. S. Office of Education, the regular defense agency of the Government which has co-operated with higher education for

Jan 1, 1941

By AIME AIME

IN accordance with the provisions of Art. XII, See. 3, of the By-laws of the American Institute of Mining and Metallurgical Engineers, the Board of Directors hereby give notice of their intention to amend the By-laws as follows : Art. V, Sec. 2. Amend by substituting the word "senior" for ('first" before the words "Vice-president" in line two of the third paragraph of said section which relates to the calling of special meetings of the Board in the absence or disability of the President.

Jan 1, 1930