Search Documents

By Andrew Case

The Port Nickel facility in Braithwaite, Louisiana, is known for pioneering hydrometallurgical processes for the 'separation and recovery of nickel, cobalt and copper. Ten years ago, in 1985, a new CRI-MET process for the recovery of molybdenum, vanadium, nickel, cobalt and alumina from spent catalysts was developed and implemented. Spent- catalysts from the petroleum industry consietute the majority of feed. These are not only a valuable-source of metals, but due to EPA regulations are frequently classified as hazardous under RCRA. Molybdenum and vanadium are selectively leached in an oxidative hydrothermal step. Alumina is then extracted in a caustic digestive leach. The unique technology produces four primary commercial products l molybdenum trioxide, vanadium oxide, aluminum trihydrate and nickel-cobalt concentrate. This paper discusses the process, modifications. during ten years of operation, and the relationship of these modifications to the future of the catalyst recycling business.

Jan 1, 1995

By Ajit Kumar Jaiswal

"Electric Arc Furnace (EAF) being a power-intensive equipment, EAF based industries are highly dependent on scarce electric energy. This is the reason Government of India is highly concerned about this and laid emphasis on the conservation of electric energy.This paper highlights factors contributing to reduction in specific electric energy consumption in EAF and suggests measures not only for power saving, but also for productivity improvement. To name a few, these are proper sealing of furnace, introduction of oxy-fuel burners, foamy slag practice, increased usage of hot metal/DRI, post-combustion of CO gas for preheating of scrap, improved selection & design criteria of electrics, power demand management, and process automation. Few cases also have been cited, where the above measures have helped in reaping significant benefits.IntroductionFor a long time, Government of India had focused on increase in energy supply, in particular, through electricity generation. Now the emphasis of Government of India has shifted from electricity generation to its conservation for following two reasons:??Power plants have become very cost-intensive??By saving energy, more of it can be delivered at lower cost to the consumersPower generating units, transmission & distribution agencies as well as consumers all have roles to play in the area of energy conservation. By energy conservation, we mean curtailing energy requirement by reducing energy wastages and taking up measures to improve energy efficiency of electric equipment/appliances. In almost all cases, this would be economically beneficial.India’s cost-effective energy conservation potential has been estimated by the Planning Commission at 23 per cent of total commercial energy generated ?1?. A national movement for energy conservation can significantly reduce the need for fresh investment in energy supply systems in coming years. It is imperative that we make all-out effort to realize this potential. Whether a household or a factory, a small shop or a large commercial building, a farmer or an office worker, every user can and must make this effort for his own benefit and for the nation’s benefit as well."

Jan 1, 2009

By Tseng. B. H.

Samples of unchlorinated and chlorinated carbonaceous concentrate from a carbonaceous gold ore were analyzed by transmission electron microscopy (TEM) for organically bonded sulfur and chlorine. The concentrate assayed 1.53 oz/t gold and 6.01% organic carbon. Much of the organic carbon occurred as sizable coarse particles up to several hundred microns in size, which showed no visible evidence of reaction with chlorine after chlorination treatment. Both the untreated and chlorinated fractions of the carbonaceous concentrate were analyzed by the TEM method, which detected organically bonded sulfur in all of the carbon particles examined in the untreated sample, ranging from about 1 to 5% organic sulfur, and averaging near 3.1%. TEM analysis of 40 carbon particles in the chlorinated sample indicated that organic sulfur was reduced significantly in the carbon and replaced in part by the chlorine, as the result of chlorination.

Jan 1, 1987

By S. R. Reddy

Thennodynamic properties of several quaternary systems are calculated using our recently modified Margules equations. The modified Margules equations are expressed up to infinite order in the vicinity of solvent. Quaternary system of one solvent and three,solute partials are derived. First order interaction coefficients of binary, ternary and cross -interaction parameters of quaternary system are used to'evaluate the partial functions. In the original fonn of Margules equations,derived partial functions are convergent and same 'as Unified ,Interaction Parameter Fonnalism. But considering up to infinite order of the Margules coefficients, the functions are divergent, in order to overcome this restriction, Margules equations are modified to get consistent equations. Derived partial functions are thennodynamica Hy consistent with Maxwell and Gibbs Duhem relations. The derived logarithmic activity coefficient of the solvent and solutes are consistent with the ternary systems. The calculated data, ie., activity coefficient values of nitrogen and interaction coefficients are in good agreement with the data of Fe-Cr-V -N. Fe-Ni-V -N, Fe-Cr-Ta-N and Fe-Ni-Ta-N systems.

Jan 1, 1999

By Pekka Hanniala

The Outokumpu Flash Smelting process today is the most feasible method for copper matte smelting. The economic feasibility of the process has always been one of the main decision making criteria in smelter projects. Thus, today about 50 % of the world primary copper production utilizes Outokumpu Flash Smelting Technology. However, in the future, environmental criteria will have stronger and stronger impact on decision making. Flash Smelting technology offers the best pollution control features of any process. today. It is foreseen that, in the near future, the global trend will be that all the smelters must decrease their emissions at an accelerating rate, compelling the smelters to make increasingly larger investments on environmental protection. In most of smelters ?today, Peirce-Smith converting and transfer of the molten material in ladles are the number one pollution source. The key today for copper converting and minimizing emissions is the Kennecott-Outokumpu Flash Converting process, which has proven to be the most effective converting method in terms of pollution control and, production efficiency including capital and operational costs. Outokumpu Flash Smelting technology is applicable also for small to medium scale smelters but the most interesting area is the upper capacity limit for smelting in one line, which has not yet been reached. We predict that by the year 2000 to 2005, there will be at least one smelter which produces 500,000 tonnes of Cu per year based on one Flash Smelting and Flash. Converting unit. The current state-of-the-art of the Outokumpu Flash Smelting - Flash Converting process is presented in this paper as well as some new options for copper production to be utilized in the near future but which are available already today.

Jan 1, 1998

By Steve Naruk

Microscopic point-count analyses, although time-consuming, provide detailed mineralogical information which is not obtainable by any other means. Such information can be invaluable for evaluating mill circuit behavior. In comparing two months of operation of a Cu-Pb-Zn sulfide flotation circuit, chemical analyses show that higher copper recoveries and concentrate grades were obtained from lower grade ore, but they provide no explanation of how the improvements were obtained. Quantitative micro-scopic analyses, on the other hand, show the following: 1. There was no change in the identity of the Cu-bearing minerals. 2. Increased copper recovery was achieved primarily by increased recovery of chalcopyrite middling particles. 3. The increased recovery of chalcopyrite middling particles also increased the amount of gangue entrained as locked particles. 4. Increased rejection of free gangue particles, particularly those finer than 25 microns in size, resulted in a net decrease in gangue content.

Jan 1, 1981

By Derek J. Fray

"A need exists for fast and accurate analysis of species in various phases at elevated temperatures. Although modern analytical techniques are very efficient, the equipment is usually situated some distance from the industrial operation and time is spent taking the sample and sending it to the analytical facility. Several minutes can easily lapse and, during this time, heat must be supplied in order to keep the system molten and, if the composition is changing rapidly due to a refining process or reaction with the environment, the information may only be of retrospective use. Perhaps more important reasons for the use of on-line sensors are that instantaneous analysis gives better control, process optimisation and the minimisation of energy losses and pollution. To date oxygen has been the only element which is measured widely using solid electrolytes. However, the analysis of many more elements is required and possible electrolytes for other species are discussed. For some elements, ~here is no suitable conducting electrolyte and, therefore, a different approach is adopted where the electrolyte, in which one species is mobile, comes to equilibrium with another species. IntroductionThere is an ever increasing demand for the development of sensors for on-line measurements in most areas of technology and, in particular, metal processing. This is especially relevant in situations where greater control can be achieved by monitoring the chemical composition of the melt during processing and where a minor constituent in the melt can have a major effect on the properties of the finished alloy. Although modern analytical techniques are fast and reliable, the equipment due to its complexity, is frequently situated away from the process area and valuable time may be spent in sampling and transportation. During this period, heat may have to be supplied to prevent solidification and the refining reactions may be continuing, and, therefore, the analytical information may not be of direct use."

Jan 1, 1988

By I. Gaballah

About forty percent of the SOx emissions are generated during the processing of metal sulfides of Cu, Pb, Zn, Ni, etc. Although new technologies for metal sulfide's smelting allow the production of H2S04 with a reasonable cost and decrease the emissions of sulfur oxides, the generated quantity of SOx is considered as a serious threat to environment. This paper suggests alternatives for low temperature processing of complex sulfide ores or concentrates 'CSO or CSC' under neutral, reducing and chlorinating atmospheres or their combination. At T > 400 "C, The neutral and reducing treatments allow the decomposition of pyrite and the partial recovery of sulfur as So and H2S. At 300 "C, the chlorinating treatment of CSC is fast, exothermic and allows the separation of FeC13 from the valuable elements' chlorides. It also generates SyCIx that can be either reduced by H2 or hydrolyzed in presence of sodium sulfide. The recovery rate of elemental sulfur with respect to the sulfur input exceeds 90 %.

Jan 1, 1999

By Hideki Minoura

"Two novel electrochemical techniques for the preparation of highly crystallized CdS film have been presented. One is cathodization of a conductive substrate in an acidic chemical bath containing cadmium salt and thioacetamide, where electroreduction of proton at small current densities induces a growth of highly crystallized CdS thin films, whose growth is not disturbed by the reactions in the solution phase. The other technique is electoreduction of aqueous Cd2+— SCN complex. An advantage of this technique lies in no formation of solid particles in the bulk, of the bath.IntroductionIn recent years much attention has been paid to materials preparation by solution processing because of its advantages in lowering the cost as well as the stress to the environment, as compared to the conventional gas phase techniques which unavoidably require high temperature and/or vacuum. We have been trying to explore novel techniques for preparing functionalized compound semiconductors by aqueous solution process. Semiconductors which we have been mainly focusing on are CdS and ZnO, which are important semiconductors finding applications in various devices. In the present paper, some of the techniques that we have recently established for the preparation of highly crystallized CdS will be presented.Methods of the CdS film processing in solution phase (wet process), which have been reported so far can be divided into two major groups; one is chemical bath deposition (CBD) in alkaline solution containing Cd2+ and thiourea 1)4) and the other is electrodeposition (ED) in acidic solution containing Cd2+ and thiosulfate ions - 5)-8) or organic solutions containing dissolved sulfur 9)-11)."

Jan 1, 2000

By P. Rooney

In due course, new smelters will have to be installed in order to meet the increasing worldwide demand for copper. This paper presents the results of a study made for the purpose of identifying the most desirable countries in the world in which to locate a new smelter. Both sociopolitical and economic factors were taken into account. Criteria developed and methods used to assess each possible location are described. The study indicated that the most interesting potential locations are Canada, -Chile, Portugal and the USA for new copper smelting complexes.

Jan 1, 1983

By J. S. Pitsillos

A new furnace tapping technique involving the simulation of a control valve at the exit to a furnace is being investigated. The purpose of this new tapping technique is to regulate the flowrate of liquid furnace products( slags, metals and mattes). Numerical modelling and experimental work has been carried out on tapping of slags leaving a SIROSMELT reactor and the results found to be in good agreement. Numerical modelling has also enabled prediction of the important industrial conditions for the onset of blockage from the shape of the pressure versus flowrate curves. Slag launder experiments have been carried out and a one-dimensional heat transfer model was used to evaluate the effectiveness of launder covers and different coolants. From the experimental results and mathematical model some launder design guidelines such as inclination angle, covers and coolants have been developed.

Jan 1, 1991

By Xie Zhang, Jiang Diao, Xin Qiu, Lu Jiang, Bing Xie, Hong-Yi Li

"Duplex converter process, in which the first converter is used for removing phosphorus from hot metal (De-P), is an important way to produce low P-content and ultra-low P-content steels. In order to improve phosphorization removal and formation of slag with high basicity at relatively low temperature during dephosphorization converter process, effects of temperature, silicon content in hot metal and varied compositions of the De-P converter slag on phosphorus distribution between the slag and hot metal were investigated with thermodynamic calculations and by laboratory scale experiments in present work. Results showed that phosphorus distribution ratio between slag and metal was varied in 10.6~26.6 when basicity of the slag was in the range of 1.5~2.1 at 1370, and the distribution ratio was increased with increasing basicity and Fe10 content in the slag.IntroductionIt is known that phosphorus exists in steel in the form of solid solution, which can significantly improve strength and hardness of steel at room temperature. However, the plasticity and toughness of steel, especially the low temperature plasticity is sharply reduced and leads to high ductile-brittle transition temperature. This phenomenon is commonly known as cold brittleness of steel [1~3]. Hence, phosphorus should be removed as much as possible in the steelmaking process, because it is generally harmful to the iron and steel products."

Jan 1, 2013

Kosaka Smelter & Refinery has a history of more than a century as a metallurgical department belonging to Kosaka mine. It has treated for a long time the "Black Ore" or the complicated concentrates dressed from it. The "Black Ore" is composed of black sulfides. It contains not only valuable metals such as gold, silver, copper, lead and zinc but also some impurities like arsenic, antimony and bismuth. With the development of Kosaka's floatation technology, five kinds of concentrates (copper, zinc, lead, pyrite and barite) have been separated from the "Black Ore" but the separation was not complete and each concentrate contained some unfavorable impuritie. In 1980s the highly appreciated yen and the drop of the metals priees forced many domestic mines to close their operations. Since then Kosaka Smelter has changed its way of operation to a custom smelter. Now more than 95% of copper concentrates are imported to take advantage of this technology of "Black Ore" treatment. It mainly treats the raw materials that contain high gold and silver like the "Black Ore". Recently, Kosaka has been working on the recycling of the metals from the printed circuit board scraps and sludge which contain some precious metals. The volume of the recycled metal is continuously increasing.

Jan 1, 2003

By Zhou Shu-cai

"A method has been proposed for the pre-treatment of high phosphorus iron ore by carbothermic reduction assisted with microwave irradiation and magnetic separation on a laboratory scale. Chemical analysis of the reduced ore sample, the metal sample and the slag sample were conducted. Based on the above research, the influences of carbon addition, microwave power and microwave irradiation time on the recovery of Fe and dephosphorization were discussed. It indicated that the increase of microwave irradiation time and power had substantial effect on the recovery of Fe while the influence of carbon addition was not obvious and the highest iron recovery ratio reaches some 95.5% when the dephosphorization ratio was 37.68%. A high iron recovery ratio and a reasonable dephosphorization rate were incompatible under the conditions investigated in this study due to the reduced iron and because unreduced P-contained gangues were not efficiently separated. This method may provide a reference for the future utilisation of high-phosphorus iron ore.IntroductionWith the rapid growth of crude steel production in China, the source of iron ore tends to become increasingly strained and is facing the risks of raw material shortage for the iron and steel industry. In order to decrease the production cost, China has to focus on the utilization of its domestic low grade iron ores for the iron and steel plants [1-2]. China has a large deposit of high phosphorous iron ore with a reserve of 7.45 billion tons which is unused in any large scale [3]. Therefore, the development of a successful and economically viable technology for high phosphorus iron ore is of profound importance. To remove phosphorus from the high phosphorus iron ore, several mineral and metallurgical processes have been proposed, such as bio-leaching [4], roasting reduction plus melting separation [5], pre-reduction and screening methods combined with mechanical crushing or air jet milling[6] selective agglomeration plus reverse flotation [7]. However these processes are not cost effective or are time consuming. The traditional pyrometallurgical process( BF+ BOF) refuse this kind of ore mainly because that molten iron is saturated with carbon or high carbon content and thus all phosphor us in the burden goes to the molten iron[8]. Therefore, it is important to exploit the cheap and abundant high phosphorus iron ore as a resource in ironmaking. In recent years, the microwave was widely introduced as a heat resource for extractive metallurgy of iron ore or other minerals. For example, microwave assisted ore milling, microwave assisted carbothermic reduction of metal oxides and microwave assisted mineral leaching issues[9-10]"

Jan 1, 2014

By Dandan Jian, Christian Karcher

Information of liquid steel flow patterns inside the mold may be obtained from the velocity at the free surface (meniscus). This meniscus flow may be measured using the contactless electromagnetic technique termed Lorentz force velocimetry (LFV). It is based on the measurement of Lorentz forces acting on a magnet system when an electrically conducting metal melt interacts with the field lines stretched by the magnet system. Force sensor and the magnet system form a so-called Lorentz force flowmeter. In this paper we present a series of model experiments that demonstrate the feasibility of using two identical flowmeters that are arranged in a certain distance one behind the other. In this case, surface velocity may be determined by just cross-correlating the two force signals recorded by the two sensors. This technique is called time-of-flight LFV. A special prototype of a respective measuring device, called meniscus velocity sensor (MVS), has been developed to measure local free-surface velocity. In the present paper we describe experimental results of respective measurements in the model test stand LiMeSCo (liquid metal surface velocity correlation). To check the potential of the time-of-flight technique, in a first step we measure surface velocities during solid-body rotation of metallic substances. We observe that small modulations in the signals that are due to the natural unevenness of the solid body can be used to determine surface velocities. In a second step we apply the time-of-flight technique to liquid metal free-surface flow. Here we use the low-melting eutectic alloy GaInSn as a test melt. In this case we observe that the cross-correlations between the signals are much rarer and much weaker than in the solid-body experiments. We conclude that the presence of the localized magnetic fields, produced by the permanent magnets of the flowmeter, give rise to intense deformation of the free surface and the creation of surface waves. The field acts as a magnetic obstacle. We observe that the flow velocity is decreased right underneath the magnetic field and is accelerated in the side regions. This magnetic obstacle effect may restrict the determination of the local surface velocity in application.

Jan 1, 2012

By Ragnhild E. Aune, Mark William Kennedy, Shahid Akhtar, Jon Arne Bakken

"To determine the heating rate of billets using ‘short coils’, an appropriate correction factor must be applied to the theoretical relationship. In 1945, Vaughan and Williamson published a semi-empirically modified Nagaoka coefficient applicable for moderate frequency induction heating processes (10 kHz). Recently it was demonstrated that the method of Vaughan and Williamson gives <10% error in the estimated power when heating aluminum billets at 50 Hz.In the present study, experiments have been conducted on aluminum billets in order to verify an empirical frequency corrected ‘short coil’ equation. Measurements of electrical conductivity (<± 0.5%), current (± 1%), heat (± 1-3%), and magnetic flux density (± 1-2%) have been performed. The results are compared with 1D analytical calculations, and 2D axial symmetric FEM modeling using COMSOL 4.2®. The frequency corrected equation has proven to provide accurate predictions of power (<4% error) within the frequency range 50 Hz to 500 kHz.IntroductionInduction heating is commonly applied to the re-heating of billets before forging or extrusion processes. The resistive heating produced by eddy currents in the solid or semi-solid work piece during this procedure, is driven by the time varying magnetic flux density in the air-gap between the work piece and the coil. The flux in the air-gap is created by the current flowing in the induction coil, i.e. the magneto-motive force. In Figure 1 it can be seen that the currents present in the work piece are concentrated in the outer ‘shell’, or the first electromagnetic penetration depth (dw), and flow in a direction which opposes the magnetic field produced by the induction coil."

Jan 1, 2012

By I. Gaballah

The kinetics of oxychlorination of pure CI-2O3 with C12+02 gas mixtures is studied by ThermoGravimetric Analysis (TGA) in non and isothermal conditions up to 1000 °C. The reaction of Cr2O3 with C12+O2 chlorination gas mixtures starts at about 550 °C and the reaction product is CrO2Cl2. The oxychlorination rate of Cr2O3 is almost proportional to the chlorine partial pressure and to the fourth root of the oxygen partial pressure in the chlorinating gas mixtures. At 800 °C, the maximum chlorination rate is obtained using a gas mixture having a C12/O2 ratio equal to 4. The apparent activation energy of the oxychlorination reaction of Cr2O3 is 87 and 46 kJ/mol at temperatures lower and higher than 650 °C, respectively. By varying the chlorine and the oxygen partial pressures of the oxychlorinating gas mixtures at temperatures higher than 550 °C, it is possible to extract selectively the chromium chlorinated compounds from the chromium bearing materials. a. Laboratoire Environnemem et Minéralurgie, BP 40, 54501 Vandceuvre, France, b. École Nationale Supérieure de Géologie, Rue du Doyen Marcel Rouhault, 54501 Vandoeuvre Cedex, France, c. Centre National de la Recherche Scientifique, 3 rue Michel - Ange, 75794 Paris Cedex, France, d. Insritut National Polytechnigne do Lorraine, Rue de la Font de Haye. 54501 Vandceuvre Cedex, France.

Jan 1, 1997

By J. B. See

Emeritus Professor David Robertson of the Missouri University of Science and Technology was born in Dublin Ireland on 29 December 1941. His father was a merchant navy Captain who served during WWII and during David’s early years his family lived in Dublin and Donegal where David went to the local elementary school. In 1954 he moved to London with his parents and attended Highgate School before commencing metallurgy at the Royal School of Mines, Imperial College, London in 1960.

Jan 1, 2014

By Ari JokiIaakso

Three different sulphidic raw materials were treated in a laboratory scale laminar flow fur-nace simulating suspension smelting conditions. The materials were a pure chalcopyrite concentrate, a high-antimony concentrate (tetrahedritic), and crushed copper mattes. The gas preheating temperatures were 500 -1 100°C ana the atmospheres ranged from N2 to N2 -75 % O2, Two particle size fractions were used for the concentrates with x = 20 -38 um and x = 62 -74 um, and three for the granulated copper mattes with x < 37 um, x = 62 -88 um, and x = 125 -177 um. Scanning electron microscopy combined with energy dispersive analysis and backscattered electron analysis was used for determining the morphology and the mineralogy of the reacted particles. Fragmentation of the particles were observed in all materials during the flash oxidation, the conditions depending on the iron and sulphur content and the original particle size fraction of the material. The melting and/or reaction stages of the particles in different conditions were studied from powder samples. Polished sections were examined in order to follow the development of porosity and the mineralogy of the particles.

Jan 1, 1989

By J. H. Ahn, J. K. Yoon, Jung-Eui Lee

"A concentration change during grade transition operation in steel thin slab casting is predicted with computer simulation, water model and plant trial. Fluid flow and mixing patterns in various tundish levels and flow rates were analyzed through three-dimensional mathematical modeling. Comparing with water model experiments, a simple, efficient and accurate computational model has been suggested to predict the concentration profile at outlet of tundish. Based on the model, mixing in/below the mold was analyzed considering EMBR. The predicted concentration profiles show good agreements with the measured values. It is found that the lower vortices in the mold are suppressed by the electromagnetic field and the plug-like flow region develops which decreases the intermixing of two different grades of steel and shortens the length of transition region.1. IntroductionContinuous casting is the primary mode of production of semifinished steel products as it offers tremendous advantages in terms of energy savings, increased yield and higher productivity over the traditional ingot casting process. Efforts have to be made constantly to improve the quality of the cast product, reduce costs and thus increase the competitiveness of the steel manufacturer. One way of reducing costs is to reduce the amount of intermixed steel during the grade transition operation.Several different procedures exist to handle the casting of dissimilar grades for the conventional slab casting. Each procedure has its own merits and demerits. In order to choose the best method for a particular operation, there are a lot of researches. In the case of present continuous thin slab casting of POSCO mini mill, the only possible method is to change ladle during the grade transition. Due to the high casting speed (3.8m/min-4.4m/min) it is impossible to change the tundish and due to the thin thickness of slab it is also impossible to insert grade separator."

Jan 1, 2000