Search Documents

By A. R. Videla, P. R. Brito-Parada, I. Mackay

"Linking results from laboratory scale experiments to industrial flotation behaviour is challenging. Typically, such experiments involve batch tests in which the system does not operate at steady-state, making it difficult to infer the effects that operating conditions have on flotation performance. In order to overcome this limitation a 4-litre recirculating tank was previously developed at Imperial College London. This tank is capable of reaching, and operating at, steady-state by recycling overflowing concentrate back into the feed. As well as instruments to control operating conditions, it is fitted with a system of sensors that allow the surface of the froth to be dynamically monitored. From this information, it is possible to measure the air recovery—a proxy for froth stability. Thus, this bench-scale tank can be used to understand the effect of differing operating conditions on flotation performance at steady state. However, so far, this cell has only been used to investigate idealised systems with only one or two species.Reprocessing of tailings dams is not only environmentally desirable but also increasingly economically feasible due to the declining head grades of primary deposits. There is also the added benefit of no further milling being required prior to flotation. However, the effects of fine and ultrafine particles on froth stability are not yet fully understood. In this work, the bench-scale continuous tank has been used for the first time to determine the flotation response of a complex feed, consisting of samples from a copper tailings dam, to changes in operating conditions. It was shown that the froth stability in the system is comparable to that of previous work and industrial tests, with a peak in air recovery being found at a superficial gas velocity of 1.13 cm/s. There is scope to optimize the froth stability of tailings flotation for enhanced metallurgical performance."

Jan 1, 2018

By Áureo Del Vecchio, Lídia Dely Alves de Sousa, José Pereira

The potassium demand for agriculture purposes has increased in Brazil, which has great deficit of internal demands. Potassium-rich rocks have been used as fertilizers as technological alternatives for agriculture aimed to reduce the amount of chemicals and the sector dependence for such products. Vermiculite tailings from União Brasileira de Mineração - UBM, at Santa Luzia - PB, was studied aiming their application in agriculture by potassium release. The sample was analyzed by XRF and XRD; studies on release kinetic with particles smaller than 2 mm added of organic acids (citric and oxalic) at 10-2 mol/L concentration; samples were analyzed by XRD after kinetic assays. The work was conducted using a shaker incubator at 300-rpm agitation and time variation to better understand the potassium availability in the ground. Results show the presence of K2O at 3.46% concentration. Citric and oxalic acids increased the release speed to almost the same level with speed coefficients (k) of 2.61x10-2 h-1/2 and 2.55x10-2 h-1/2 respectively. In statistical terms for both acids, the linear equation represents more than 99.0% of the experimental assays. Stonemeal was applied to banana seedlings in experiment conducted in a greenhouse. The use of vermiculite tailings in banana seedlings promoted potassium absorption, which influenced its growth. The amount of potassium liberated from vermiculite tailings could be used as a long-term alternative to fertilizers in agriculture cultures.

Jan 1, 2014

By M. Brennan, A. Majumder

"The mineral processing research community has devoted enormous efforts to the modelling of mineral separators over the last 50 years. While many efforts have been made to use only fundamental physics as a basis for the models, fluid flow patterns in separators are not simple while the motion of particle swarms through fluids is extremely complex.Sluices are the simplest forms of the flowing film concentrators and have been used in the mineral industry since at least the 15th century (Agricola, 1556). Flowing film concentrators, in general, still have widespread applications in the mineral industry and their designs vary according to the specific need.Particle separation in a sluice appears deceptively simple, but the separation mechanism has proven complex and difficult to quantify. Separation in the sluice takes place in a flowing film a few millimetres thick. The particles are suspended by turbulent eddies and motion relative to the fluid takes place in socalled hindered settling mode. The difficulty arises because the presence of the particles influences the flow pattern and when the particles are fully transported by the flow, the flowing slurry may not have the same viscosity as water and does not have the same density. For this reason a universal theory which can explain the behaviour of a suspension in a sluice or any other gravity equipment has still not been developed. Few attempts have been made to analyse the mechanisms involved in the concentrating processes of pinched sluices and Reichert cones.Fluid flow behaviour and slurry transportation characteristics in open channels have, however, been active research topics in the disciplines of fluid mechanics, chemical engineering and civil engineering for many years. As a result, an extensive literature is available, which has led to the development of the model described in this paper.In an effort to test the extent to which fundamental fluid mechanics can provide a prediction of particle separation, a study on a simple parallel-sided sluice has been carried out using glass beads at various particle concentrations and flow rates, and the actual particle separation taking place compared to predictions from modelling.The modelling strategy was divided into two parts; the first was to predict the horizontal slurry flow velocity profile and the second to predict the solid particle concentration over the depth of the flow at different flow conditions. The predictions were then validated with measured data sets. This can easily be done if the slurry flow is split at different fractional flow depths so that the mass flow of solids over different flow heights is measured accurately over a fixed period. Mass flow splits can then be calculated by integrating the product of the predicted slurry velocity profile and the predicted solids concentration profiles from the base of the sluice bed to the slurry free surface."

Jan 1, 2003

By H. Gallardo, J. Yianatos

Flotation is a separation process in which mineral recovery depends on the particle surface properties. The selective collection of particles by air bubbles requires hydrophobic mineral surfaces. Hydrophobicity can be selectively induced on a valuable mineral surface by means of reagents. For this purpose, it is required that mineral grains in the ore become physically liberated or exposed in the particle surface after grinding. The grinding process generates three types of particles according their exposed surface in the floatable mineral: locked particles (0-10%), associated particles (10-90%) and liberated particles (90-100%). Locked particles have low floatability, and they typically show low recovery (<20%), while liberated particles have a high floatability and can be easily recovered (98-100%) at different particle sizes (10-150 µm). The main challenge in the flotation process is the recovery of associated particles. These particles typically have recoveries of 20-80%, but strongly depend on the particle size, particle surface liberation and collector dosage. Recent studies on particle floatability by size-liberation have significantly contributed to improving the characterization of flotation processes. In this work, a study of flotation recovery of associated particles of 10-90% liberation is presented for particle sizes (10-150 µm) and collector dosages (5-40 g/ton). In this work historical data on galena recovery based on particle cross-section composition of galena was used, assuming they represent an acceptable estimate of particle surface composition, as shown by some previous researchers. The results showed that galena recovery can be well represented by a model consisting of the interaction of a linear function and a Gamma distribution function to account for the liberation and the particle size effects. Consequently, an alternative approach for modelling the recovery of associated mineral (10-90% liberation), with a reduced number of parameters, was developed and validated.

Jan 1, 2018

By S. Gomez, P. A. Bebswa, A. N. Mwale

"The research aimed at improving the way screen performance analysis is conducted using a model that accounts for most feed and design parameters in its formulation. Thus, the aim was to validate the fine screen model that was developed at the Centre for Minerals Research (CMR) unit at the University of Cape Town. Fine wet screening is increasingly becoming an important application in fine grinding operations. Minera Saucito, a lead-zinc Mexican mine has replaced hydrocyclones with eight stacks of five decker derrick screens to close the ball mill in their concentrator plant. The five decker stacks have improved the overall plant throughput by 20% and have had the ball mill circulating load reduced considerably. As a continuous plant optimization process, a number of surveys were carried out to assess the performance of the 75 µm panel aperture installed screens. The surveys were conducted at seven different feed rates to the entire nest of screens to collect performance data. Using the fine screen model to analyze the results, it is found that as the feed rate increase, the sharpness of separation reduces. The CMR fine screen model was fitted to these results. The model fits the plant data with good accuracy. Simulated results based on this model are also presented.INTRODUCTION The potential of high frequency vibrating screens has long been identified as an alternative to hydrocyclones in grinding applications (Rogers and Brame, 1985). However, high frequency vibrating screens have had two main disadvantages, low capacity and high wear rates (Kelley and Mckeon, 2005; Teknikk, 2009). Current vibrating screen technology overcomes these challenges by multiple deck screen design and use of wear resistant urethane materials for panel construction (Kelley, 2007; Valine and Wennen, 2002). For a example, the Derrick screen’s material of construction is a tensionable urethane that provide high open area ranging between 35 to 45% with considerably reduced blinding (Valine and Wennen, 2002). Thus, there has been an increased uptake by the mining industry in the use of wet fine vibrating screens closing the ball mill as the final classification stage in the comminution circuit (Barkhuysen et al., 2010; Frausto, Ballantyne et al. 2017; Pelevin and Lazebnaya, 2009; Teknikk, 2009). Even though there is a number of models in existence, none of these models adequately predict the performance of high frequency vibrating screens (Karra, 1979; Rogers, 1982; Subasinghe et al., 1990; Trumic and Magdalinovic, 2011). Recently Mwale et al., (2016) developed a model for predicting the performance of high frequency vibrating screens using the partition curve properties. The input parameters of the model include screen open area (??) in m2, tonnage feed rate (????) (tph) and the weight fraction of solids (??) in the feed for a given panel aperture size. The model was developed based on data collected from a single deck industrial size derrick screen, in a pilot setup. The work presented in this paper is an attempt to test this model using data collected from Minera Saucito concentrator, an industrial plant whose comminution circuit is shown in Figure."

Jan 1, 2018

By Jaime Sepúlveda

"A broad diversity of critical operating conditions may influence, in very convoluted ways, the actual performance of any given mineral processing system, to the extent that it becomes nearly impossible to empirically determine the independent, decoupled impact of each condition. An effective approach to better understand the behaviour of such complex systems is via the extensive use of sufficiently detailed and reliable mathematical models, allowing the process analyst to explore and learn about the independent effect of all relevant operational conditions. Certainly, these tasks are greatly facilitated if the appropriate software tools - such as the Moly-Cop Tools software package - are readily available. Moly-Cop Tools 3.0 is a set of 63 easy-to-use EXCEL spreadsheets designed to help process engineers characterize and evaluate the operating efficiency of any given grinding circuit, following standardized methodologies and widely accepted evaluation criteria. Moly-Cop Tools 3.0 covers conventional and semiautogenous mills, crushers, HPGR’s, rod mills and vertimills, with the corresponding mass balance and parameter estimation routines; plus complementary spreadsheets regarding Bond’s Law calculations, grinding media selection and performance evaluations and other useful utility functions. As a relevant example of application, specifically focusing on semiautogenous grinding operations, the current publication describes how the models can help us learn and rationalise critical empirical observations such as the relationship between feed particle size and optimal ball filling, the role of the rocks as autogenous grinding media as well as the impact of feed size and discharge grate opening on the mill grinding capacity. Over the last 20 years, Moly-Cop Tools has gained wide acceptance around the mineral processing community in recognition to the quality of the mathematical models contained, their simplicity of application and ease of sharing of the calculations amongst all interested parties, since it is available free-of-charge with no restrictions to make as many copies as needed."

Jan 1, 2014

By Wei Sun, Xue-feng Cao, Lei Sun, Run-qing Liu

The flotation performance of kaolinite in laboratory micro-flotation was investigated with 3- (dodecyloxy) propan-1-amine (ON12) as the collector. Compared with dode cylamine (DDA), which is commonly used as the bauxite reverse flotation collector, ON12 shows stronger collecting ability for kaolinite than using the same amounts of DDA, when experimental pH value reaches more than 6. With the addition of ON12, the isoelectric point of kaolinite shifts to 6.1 from 3.6, which suggests a strong adsorption between kaolinite and ON12. Infrared spectra analysis indicates that the type of ON12 adsorbed on the kaolinite surface is mainly of electrostatic adsorption. Molecular dynamics simulation further indicate that electrostatic adsorption of ON12 cation on kaolinite (001) surface based on electrostatic interaction between NH4+ and O atoms. ON12 will be suitable for bauxite reverse flotation with the efficiency depressors of the diaspora.

Jan 1, 2014

By Joseph Kelly, Christopher Kelsey

This revolutionary super-fine crusher has the unique capacity to generate fine and ultra-fine products from single stage reductions of coarse or fine mineral feeds. The crusher consists of a rotating compression chamber and an internal gyrating mandrel. The axis of rotation of the shell is displaced relative to the axis of the vertically mounted mandrel. The inner surface of the compression chamber is machined as double cone frustums at an angle equal to the displacement angle. Crusher feed is accelerated into a compacted particle bed, which lines the inside of the compression chamber. The depth of the compacted bed progressively increases until the mandrel is engaged. The mandrel is then free to rotate with the compression chamber. Continued feeding increases power draw and triggers the counter rotating mandrel gyration drive. The gyrating mandrel delivers multiple compressions at high pressure to the rotating particle bed. High concentrations of energy are harnessed within a small active volume over short retention times. The combination of extraordinarily high power intensity and extreme compressive force results in primary compressive fracture and induced secondary tensile failure. The axially displaced rotation of the compression chamber effectively distributes the breakage forces throughout the particle bed. This paper covers open circuit, pilot trials on magnetite, perlite, garnet, marble and a copper/pyrite concentrate. Particular emphasis is placed on the extraordinary results achieved with trials on zircon and highly refractory fly ash. The extreme duties were deliberately chosen to demonstrate the crusher’s application scope and potential to impact capital operating and maintenance costs as the technology matures. Super-fine crushing, once considered impracticable has the potential to offer compelling options for the generation of ultra-fine products.

Jan 1, 2014

By Gabriela Pino, Maurício Torem, Diego Veneu

Because of its simplicity, economy and biocompatibility, research regarding the use of microorganism for decontaminating heavy metals produced by many industries is an area of growing interest. Also, there is a stringent need for the control of toxic metals produced during various production processes and released into the aqueous environment in order to avoid damage relevant to soil or groundwater contamination. Among the available treatment technologies, sorptive flotation has been considered as a promising alternative for the wastewater treatment. In the present study Streptomyces lunalinharesii strain was applied as bioreagent for the removal of copper, cadmium and zinc. The removal of those metal ions depends mainly on the respective pH value, influencing the aquatic speciation during the process, as well as the zeta potential of the system and biomass concentration. Langmuir and Freundlich isotherms have been depicted. Dispersed air flotation was applied as the subsequent separation method for harvesting the suspended metal laden microorganisms, following the biosorption of copper, zinc and cadmium. The investigated parameters (in batch mode, laboratory scale) were in this case the saturator pressure, the coagulant concentration and the recycled flow. Applying the optimum defined conditions, over 60% removal of metal ions have been achieved in one stage and simultaneously, quantitative separation of the used (metal-loaded) biomass has been obtained.

Jan 1, 2014

By C. Y. Sun

Flotation of chalcopyrite and unactivated malachite with xanthates (ethylxanthate, butylxanthate, octylxanthate and dodecylxanthate) is studied in this paper. Minerals interacted with xanthates are detected by FTIR, and simulated by molecular mechanics. It shows that chalcopyrite can be floated with 4 kinds of xanthates, and unactivated malachite can?t be floated with ethylxanthate but can be floated directly with later 3 kinds of xanthates while characteristic absorption peaks of those four kinds of xanthates are all detected by FTIR on chalcopyrite and malachite surface. After simulating the interaction between xanthate and mineral, it shows that H2O and OH-can interact with chalcopyrite and malachite, and their interaction energy may be so called energy bulwark which must be overcome by collector when collector interacts on minerals; the two sulfur atoms in xanthate group interact with copper and neighbor iron atoms on chalcopyrite. It also shows that molecular mechanics results with logP of collectors can interpret the mechanism of xanthate-mineral on atom scale.

Jan 1, 2014

By Olga D. Khmelnitskaya

The paper presents the results of research on the development of gold recovery technology from oxidized gold-copper ore of one of deposits in Russian Federation. Gold and copper grades in the ore are 9.5 g/t and 0.4%, respectively. Various options of flowsheets, such as direct cyanidation, thiourea leaching, flotation and gravity concentration followed by subsequent cyanidation of con-centration products, were tested. It was established that gravity-cyanidation technology with filtra-tion leaching tails and the use of solutions in the recirculation is the optimal option for ore treatment. The proposed flowsheet provides gold recovery for 91.0% at NaCN consumption 2.5 kg/t ac-cording to the results of pilot testing. Ammonia-cyanide gold leaching was also examined. In comparison with cyanidation, gold leaching solution in system NaCN-NH4OH-(NH4)2CO3 allows NaCN consumption to be reduced three times from 4.5 kg to 1.5 kg per 1 ton of the ore and provides the same gold recovery. Based on the laboratory and pilot plant tests results of gravity-cyanidation technology of gold dissolution, process design criteria were developed.

Jan 1, 2014

By Igor P. Solozhenkin, Peter M. Solozhenkin, Sanda Krausz

"In this work, authors will show the efficiency of computer technology and chemical programs at studying collectors for flotation of minerals of elements of platinum group (EPG). Clusters various minerals EPG (flotation reagents) are created, named us clusters minerals (reagents) as their structure corresponds to the chemical formula, and the distance between separate atoms corresponds to the known tabulated data. By molecular modeling are investigated clusters sperrylite PtAs2, stumpfilyte PtSb, sadberryte PdSb, sobolevskite PdBi, palladoarsenyte Pd2As, paolovyte Pd2Sn, rustenburgyte (Pt3Sn, Pt6Sn2) and their computer parameters (absolute rigidity, electronegativity, transfer factors of carry, charges of the atoms) are determined. Tellurides of palladium (IV, II) merenskyite PdTl2 and kotulskyte PdTe and platinum clusters are investigated: PtFe4, Pt3Fe, PtFe (Pt2Fe2), Pt2Fe (Cu) Ni. The technique of attachment of the collector (composites) to cluster atoms EPG is offered. For the first time, it is established that at linkage of flotation collectors on monodentate, bidentate and bridged to circuits with atoms clusters the minerals containing atoms As, Sb, Bi, Pb, Sn, reaction of connection with change of a degree of oxidation of these atoms and occurrence of a proton operates. It is executed virtual skirling organic compounds connections by the developed criteria from accessible libraries of a database. The principle of an estimation of interaction energy for flotation reagents with mineral clusters is offered. It is developed the prognosis of collector activity evaluation (P?AE) and his values for candidates in collectors for flotation of minerals EPG are calculated. For flotation of ores containing Pt and Pd minerals, a number of reagents, including compounds on basis P (III), for innovational technology of Pt, Pd mineral flotation are recommended. Key words: flotation, minerals, flotation reagents on the basis of phosphorus (III), molecular modelling, chemical programs, program ????? , electronic energy."

Jan 1, 2014

By Zhou Yucai, Zhou Jing, Zhu Yimim

"In this article, research on the beneficiation process for a carbon containing copper-molybdenum deposit in Henan province has been carried out. The elemental composition, mineral composition and relative content, characteristics of embedded and symbiotic relationship, the forms of the copper-molybdenum particlesand their disseminated features, and particle size distribution have been worked out. Flotation behavior of copper-molybdenum mixed flotation and separate flotation in the systems of different collectors and depressants, and the influence of different flowsheets on the copper-molybdenum separation have been investigated by actual ore flotation tests, The separation problem of copper-molybdenum for a carbon-containing copper molybdenum ore has been solved.INTRODUCTION In this paper, technological mineralogy, small experiment of flotation recovery of copper Molybdenum ore, and expansion experiment of mineral recovery of copper Molybdenum ore are introduced. (1) The results of process mineralogyshow that the content of copper is 0.42%, molybdenum is 0.021% in the raw ore, they mainly exist in the form of sulfide, with low oxidation rate. (2) The results of flotation tests show that the combination of butyl xanthate and isopropyl ethylthionocarbamate reagents is effective collector of copper-molybdenum mixed flotation for carbon copper molybdenum, (3) When the grinding fineness is -0.074 mm taking 71%, and regrinding fineness is -0.038 mm taking 85%, the flowsheet of first copper-molybdenum mixed flotation and then regrinding rough concentrate and last separation flotation of copper and molybdenum was adopted, which realized the effective separation of copper and molybdenum for carbon-containing copper molybdenum ore. Good flotation indexes were gained with copper concentrate containing 20.96% copper and copper recovery 90.06%, and molybdenum concentrate containing 46.78% molybdenum with molybdenum recovery 72.68%. (4) The seven days average concentration index of scale-up the continuous dressing experiment is as follows, the copper content in copper concentrate is 20.16% and the recovery is 89.61%; the molybdenum content in molybdenum concentrate is 24.58% and the recovery rate is 74.09%."

Jan 1, 2018

By Buks Kruger

"After the milling and flotation of the platinum bearing ore, the flotation concentrate is electrically smelted in 6-in-line electric arc furnaces and the resulting furnace matte treated in Peirce Smith converters to remove the iron sulphide. The iron free (less than 1% Fe) converter matte is then granulated and sent to the Base Metals- and Precious Metals Refineries for further processing.During the smelting and converting processes two distinct gas streams are produced.The Peirce Smith converter off gas contains 4% - 9% SO2 which is treated in a conventional Sulphuric Acid Plant to produce sulphuric acid (H2SO4).The electric furnace off gas contains 0.9% SO2 and was (until September 2002) vented through a 91 meter high stack to atmosphere.Off gasses which contain less than 3% SO2 is difficult to handle and quite a few processes had been developed over the years to cope with this gas. A broad spectrum of process suppliers and technology approaches is available and the different technologies can be divided into a few main approaches i.e.Scrubbing of the off gas with an alkaline solution to produce an environmentally friendly and stable waste product which can be discharged onto a tailings dam or permanent landfill site.Physical absorption of the SO2 into a chemical solution to produce high quality chemically pure process chemicals.Catalytic reaction of SO2 with O2 to produce SO3 which is absorbed in water to produce sulphuric acid of less than 90% strength.In October 2002 Impala Platinum commissioned a Sulfacid Plant at its Smelter in Rustenburg which recovers the SO2 from the electric furnace off gasses into a weak sulphuric acid solution.The Sulfacid Plant technology is widely used in the paint pigment industry. This is, however, the first application of the technology on electric furnace off gas.The furnace off gasses contains flue dust which is removed in electrostatic precipitators. The gas exiting the precipitators normally still contains between 40 mg/Nm3 and 60 mg/Nm3 dust and passes through a quench-scrubber before entering the reactors. The quench-scrubber cools the electric furnace offgas down from ± 200 °C to 60 °C and act as a final dust removal stage."

Jan 1, 2003

By G. Merazchiev

In the selection of copper ? molybdenum concentrates with the use of reagents containing sulfide ion ? sodium sulfide, sodium hydrosulfide etc for depression of copper minerals and pyrites, big part of depressor is oxidized by oxygen, which is dissolving in pulp during aeration with air in flotation machines and it is expended unproductively. This is the main reason for the big expenditures of depressor, reaching up 15~20 kg/t collective concentrate and the high exploitation expenditures for the copper ? molybdenum selection. Effective direction for lowering expenditure of depressor and increasing of the technical ? economical effectiveness of moly production is the conducting of the selection in nitrogen medium. In the paper are shown the results, obtained by applying of this direction in selection of collective copper ? molybdenum concentrate from the porphyry copper deposit ?Ellatzite? ? Bulgaria, in which the ratio Mo:Cu is over 1:120. In laboratory conditions, through comparative experiments in medium of air and nitrogen are defined: expenditure and initial concentration of NaHS in pulp for effective depression of copper minerals and pyrites; kinetics of flotation process of molybdenite; influence of pulp density; emf (negative milivolts) of pulp and the expenditure of nitrogen on tech-nological indexes of molybdenum flotation. When working in nitrogen medium decrease of NaHS in rougher molybdenum flotation from 40% to 45% is settled. When nitrogen is also fed in cleaner stages, the total expenditure of depressor is lowered by 64%. The quality of end molybdenum con-centrate is raised with over 5%. On the ground of the results of laboratory studies and of world practice data, an industrial installation for selection of copper ? molybdenum concentrate in nitrogen medium in Wemco inert ? gas machines.

Jan 1, 2014

By Tom Leistner, Urs A. Peuker, Martin Rudolph

"It is well known, that for conventional froth flotation techniques the processing of ultrafine mineral particles is generally inefficient and results in rather low-grade concentrates and relatively high losses of valuable minerals. Therefore, the investigation of other possible methods, which can selectively separate such fine particle systems effectively, is of considerable interest. In this study, the application of two-liquid flotation, a flotation-related process using oil droplets instead of air bubbles, is investigated as a possible processing strategy for the separation of ultrafine particle systems. The investigation involves the testing of the two-liquid flotation technique as simple laboratory-scale batch trials and moreover, the up-scaling to a semi-continuous process by using a modified lab scale flotation column. Magnetite and quartz particles, with particle sizes below 10 µm respectively, as academic mineral mixture and iso-octane and water as the two immiscible liquid phases are chosen for the experiments. To manipulate the wettability of the magnetite particles as well as the interfacial tension of the oil/water interfaces, surface active reagents of fatty acid basis are introduced in the system. The selectivity of the process is characterized by determining the removal of magnetite particles from the aqueous suspension through selective accumulation at the oil/water interface or extraction into the oil phase, respectively. Operational parameters including pH of the aqueous suspension, additional electrolyte addition and surfactant type as well as dosage are varied in order to maximize the efficiency and stability of the process."

Jan 1, 2014

By Yuqing Feng, Ping Fang, Dezhou Wei, Zichuan Guan, Shuling Gao, Baoyu Cui

"Air core, as an inevitable phenomenon of rotational flow field inside hydrocyclone, has a major impact on hydrocyclone’s separation characteristics. The air core formation process, its structural features and its influencing factors were investigated systematically in this paper. Numerical study on the air core of a f50 mm hydrocyclone was carried out using a commercial computational fluid dynamics (CFD) modelling software package ANSYS/Fluent with the selection of Reynolds Stress Model (RSM) for the turbulence model and Volume of Fluid (VOF) for capturing the air-liquid interface. Physical experiments were conducted under the same geometry and operation conditions and the particle image velocimetry (PIV) technology was used to measure the liquid flow. The CFD results are compared with the experimental measurement with good agreement demonstrated. The air core was formed generally at around 0.7 s, air outsides of the air core was eliminated completely after 1.7 s. The centreline axial velocities and the water blocking hydrocyclone simulations showed that air of the air core entered the hydrocyclone from the underflow area and exhausted from the overflow area, but there was also some air flowing into the air core from the overflow area. The largest swing of the air core occurred on the top of the underflow pipe, and a protuberance similar to the shape of Adam’s apple appeared when the air entered the vortex finder. CFD simulation results also showed that the air core diameter was decided by axial position and parameters of hydrocyclone. The structural parameters have more effects on the air core diameter than the operational parameters."

Jan 1, 2014

By J. D. Miller, C. L. Lin

In general, x-ray computed tomographic (CT) techniques are able to provide 3D images of the internal structure of opaque materials in a nondestructive manner. The unique cone beam geometry allows acquisition of all 2D projections with only one rotation of the sample thus providing for fast data acquisition and better x-ray utilization, as a complete 2-D detector array receives the cone-shaped flux of rays. Thus, an isotropic 3D volume can be reconstructed without the mechanical translation and the stacking of sequential slices as is the case for more conventional CT scanners. In this regard, a state-of-theart, custom designed x-ray microtomography facility to provide very detailed 3D spatial analysis of multiphase particles has been installed and is in operation at the University of Utah. The reconstructed 3D tomographic volume allows for an adjustable spatial resolution from 5 to 20 microns for sample dimensions from 10 to 40 mm in diameter, respectively. For example, a packed bed of coal particles is shown below in which different crystalline froms of pyrite are distinguished in 3D.

Jan 1, 2003

By V. Avdochin

The main reason of flotation process fluctuations is mixing ores of various properties from various sections of a deposit. Other, also important reasons are changes in parameters of facilities of technological cycle, as well as properties of reagents applied. According to estimates, instability and non-optimized parameters of flotation owe 3% to 6% of valuable component losses. Without ore averaging systems flotation process is characterized by considerable fluctuations of all input, output and intermediate parameters. Stab One more way is optimizing the process, providing for determination and maintaining optimal parameters of the process. In these conditions application of various mathematic models does not allow controlling the process by the way of action on input parameters of the process with further precise reaching required values of output parameters. More effective is to be application of flotation models for solution of questions of choosing and optimizing of automatic control systems. The work presented examples of application mathematic model of flotation process for estimation of effectiveness and choice of parameters of automatic control system that reduces considerably a stage of preliminary studies in elaboration, designing and modernizing automatic control systems.

Jan 1, 2014

By B. McFadzean, K. Moller

"The mechanism whereby thiol collectors adsorb onto a mineral surface has been widely studied. Most of these studies examine the mineral surface at equilibrium state and, often, well above monolayer coverage. However, the formation of species at the mineral surface is a complex process that is both kinetically and thermodynamically controlled. In a typical industrial application, the dosage of collector will be around monolayer level. This study uses isothermal titration microcalorimetry to measure the heat evolved during the reaction of sodium ethyl xanthate (SEX) and sodium isobutyl dithiocarbamate (SIBDTC) and their mixtures with galena and chalcopyrite. The sensitivity of the instrument allows heats of reaction of sub-monolayer quantities of thiol collector to be measured.The study found that both the magnitude and kinetics of the reaction between a collector and a mineral surface was dependent on the type of mineral and the type of collector. Proposals are made for the reactions based on literature and the evidence from this investigation. It was found that when collectors were reacted with mixtures of galena and chalcopyrite, that the magnitude of the reaction was lower compared to that measured for the pure minerals alone. This may be due to galvanic interactions between the minerals, resulting in a passivating effect on one or both of the minerals."

Jan 1, 2014