Search Documents

By Yazen Khasawneh, Osvaldo P. M. Vitali, John E. Agee, Mohammad Nassim

A 3D FEM modeling of a ground improvement solution for an ice rink slab with stringent differential settlement limits is presented. Due to the complexity of the geotechnical conditions and strict deformation requirements, a structural slab supported by micropiles was initially proposed. However, this solution was costly and alternative solutions using ground improvement techniques were investigated. The proposed slab is supported directly on rock at one end and on approximately 45-ft deep cohesive soils on the other end. The numerical simulations show that differential settlement would be larger than allowable, if the ice rink slab is supported directly on the existing subgrade. The addition of the ground improvement scheme with compaction grouting demonstrated that the anticipated differential settlements are reduced significantly and would become less than the allowable magnitude. This study demonstrates that the use of numerical simulations to study complex loading and geological conditions will help to optimize designs and may result on significant cost savings.

Sep 8, 2021

By George J. Tamaro

The design and construction of foundations in the New York City area are usually dictated by the widely varying geologic conditions encountered in the five boroughs, particularly along the spine of Manhattan Island. Rock extends well above sea level at the northern reaches and falls to depths in excess of 250 m at the barrier islands at the southern extremities. These highly variable geologic conditions, significantly affected by glacial activity, dictate different design and construction approaches throughout the five boroughs of New York City. Extensive rock removal is required at the north while long piling is dictated in the south. Similar changes can occur within a project site on Manhattan Island. This paper will describe these conditions in general, will identify the various solutions used to solve these problems and will summarize various foundation types used in the New York City area.

Jan 1, 2000

By Tomohide Takeyama, Binh T. T. Nguyen, Masaki Kitazume

"Deep mixing columns are widely used to support embankments constructed on soft ground area. Researches on the stability of deep mixing columns were done by some authors when the columns do not simultaneously fail but individually fail at different time. A layer of shallow mixing is proposed to reinforce these columns as a group to increase the stability as well as loading capacity of columned improved area. Two centrifuge model tests were done to observe the effect of shallow layer on reducing embankment displacement as well as on failure pressure of improved ground. Acrylic piles were used as deep mixing columns in the centrifuge tests to avoid unexpected internal failure of columns. The results of centrifuge tests were also simulated by 2D FEM to back-analyze the centrifuge experiments. A good agreement between the centrifuge experiments and the numerical simulations shows that by using a shallow layer reinforcing individual columns, the horizontal displacement at the embankment toe reduces by 60 % and the tilting failure is clearly indicated in columns without shallow layer. Although, no significant failure was observed under the current centrifuge condition, the failure pressure of improved ground was significantly increased with the columns reinforced by shallow layer.INTRODUCTIONCement or lime and soil mixing technique was firstly used in Japan and Nordic countries since 1970s. The technique is used to improve soft soil by increasing its mechanical properties including strength and consolidation characteristics (Kitazume and Terashi 2013). Various researches were done to investigate the characteristics of mixing material due to various factors including types of binder, condition of soil, mixing condition and curing condition (Terashi 1997). On the other hand, many studies focused on the application of in-situ mixing technique such as supporting embankment and underground structure as well as working as the foundation of building and factory (Kitazume and Terashi 2013). In term of embankment supporting, column-type improvement is taken into account for huge applications. Due to loading from embankment, the deep mixing columns tend to fail either external failure (Kitazume and Maruyama 2006) or internal failure (Kitazume and Maruyama 2007). However, the deep mixing columns do not fail simultaneously but instead one by one at different time (Kitazume and Maruyama 2007). Because the deep mixing columns work and fail individually, the strength and stiffness of all columns cannot be mobilized simultaneously. By using a shallow mixing layer fixing the top of deep mixing columns, individual columns may work simultaneously. A combined technology of shallow stabilization and floating-type cement treated columns is used to reduce settlement of a high embankment on soft ground (Ishikura et al. 2007). A research on effect of surface improvement layer on internal stability of group column type deep mixing improved ground under embankment load was reported in the Port and Airport Research Institute, Japan (Kitazume 2011). However, the failure pattern of shallow and deep mixing combined structure has not well studied. This research focuses on the external failure mechanism of the combined structure by centrifuge model tests and back-analyzed simulation using 2D finite element method. The effect of shallow layer on embankment displacement and the yield point of the improved ground is also discussed in this study."

Jan 1, 2015

By Unnikrishnan Nair, Sandeep S. Nikam, Sanjay D. Patil, Prabir C. Basu

"Mumbai Metropolitan Region Development Authority (MMRDA) entrusted to implement Monorail Systems in various parts of Mumbai Metropolitan Region (MMR) with the objective to supplement the present transport system in MMR. The stretch of Monorail is starting from Sant Gadge Maharaj Chowk (SGMC) and extending up to Chembur Railway Station, divided into 2 phases. Construction of Phase 1 (Chembur to Wadala Depot) is complete and Phase 2 (Wadala Depot to SGMC) is under construction.Monorail runs on prestressed girder (guide beam) of span ranging from 20m to 28m supported on pier founded upon group of end bearing piles embedded in rock, pile group ranging from 2-4 piles of diameter 1000mm each.For the purpose of site characterization, geo-technical investigations were carried out along the alignment of Monorail system as mentioned above. These investigations included field and laboratory tests. The subsurface strata mainly consist of silty sand, gravel, underlain by marine clay extending up to stronger basalt rock with volcanic breccia. Overburden consisting of mainly marine clay ranging from 5.5m to 11m at all locations within the influence zone of settlement.The existing rigid pavement along of Sion-Koliwada and Anik-Wadala were constructed about 5 years prior to the construction of Monorail piers. Before laying the rigid pavement, to improve the geotechnical strength of subsoil (mainly marine clay), ground improvement using stone columns was undertaken by MMRDA. In light of limited right of way, the Monorail piers have been constructed in the median portion of the road. The line became operational on February 2014, in few months it was noticed that, in the vicinity of the Monorail piers, along Sion-Koliwada link and Anik-Wadala link, the Road Pavement Quality Concrete (PQC) panels adjacent to the Monorail piers started showing distress in form of nonuniform settlement of the concrete panels.Effect of pile foundation on pavements/PQC slab distress and possible causes of distress were investigated. Initially the distress was thought to be upheaval of monorail pier cap, but further investigations revealed the same to be soil settlement occurring over time. This paper describes the investigation carried out for identifying the cause of this settlement."

Jan 1, 2015

By Kanagarajah Ravishankar

Drilled shaft (caisson) foundations are extensively used in the past. In the central part of New Jersey, the soils consist of silt and clayey silt overlying Triassic age shale bedrock. The shale is friable and generally severely weathered and highly fractured. The shale crumbles readily into small fragments. In general, the shale is encountered in shallow depth. Subsurface investigations indicated that the upper part of the shale is very soft, highly weathered, and able to advance through soil exploration methods. The underlain formation is relatively hard and required rock coring techniques for sapling. Individual core recoveries ranged from 10 to 100 percent and Rock Quality Designations (RQD) vary from 0 to 90 percent. Although several methods available to estimate the axial capacity of drilled shafts, it is a difficult task for the designer choose the suitable method due to self disintegrate nature of the shale. In the recent years several bridge foundations have been constructed using drilled shafts founded on shale rock in the vicinity of the central New Jersey. Based on load tests carried out on drilled shafts during construction, subsurface exploration, and laboratory tests, suitable methods for determining axial capacity of drilled shafts is analyzed. This paper presents the findings of the field tests and suitable methods to determine the axial capacity of drilled shaft founded on soft shale. Key words: Drilled shaft, axial capacity, Osterberg load test, shale.

Jan 1, 2006

By Terry Eldridge, Keith MacKay, David Siddle, Luke Moger

On August 4th, 2014, a breach occurred in the Perimeter Embankment of the Tailings Storage Facility (TSF) located at the Mount Polley Mine, releasing approximately 10.6 million m3 of supernatant water, 7.3 million m3 of tailings solids, 6.5 million m3 of tailings interstitial water and 0.6 million m3of construction materials. A Temporary Upstream Rockfill Berm was constructed between August 2014 and February 2015 within the area of the tailings dam failure in order to retain the remaining tailings solids during the low flows of the winter season. The Temporary Upstream Rockfill Berm was constructed as part of the initial response phase, with the primary objective to abate the flow of tailings into the receiving environment. A secondary objective of its construction was facilitating the required investigation works downstream of the tailings dam failure. The selection of the coarse grained material used in the construction of the Temporary Upstream Rockfill Berm was based on the availability of the material (timeliness of construction) and the non-water retaining design of this initial response phase. Consequently, an alternative method was required in order to prevent further loss of mine-affected water and tailings from the TSF, as well as to provide short-term contingency water storage, during high flow conditions expected in late spring. Golder Associates Ltd. designed the 2015 Freshet Management Embankment, a deep mixing cut-off wall, to meet these site requirements, which was constructed by Mount Polley Mining Corporation and Golder Construction Inc. between December 2015 and April 2015. The works included 132 soil cement panels constructed to depths of up to 27 meters. This aspect of the works was completed using an RG25S Bauer CSM rig on a 24 hour per day, 7 day per week schedule. The cut-off wall specifications included a target unconfined compressional strength (UCS) of between 1 and 2 MPa, a maximum hydraulic conductivity of 1x10-6 cm/s, and a ductility to enable the soil cement to undergo a minimum of 5% strain without a reduction in strength or increase in hydraulic conductivity. In order to control and assure the quality of the soil cement, 2553 wet grab specimens were retrieved from the fresh soil cement panels using a project-developed sampler. Four of the soil cement panels were cored with a mud-rotary drill rig and optical and acoustic televiewers were placed into the boreholes in order to log several relevant parameters, including image, texture, relative hardness, borehole-shape, and temperature.

Jan 1, 2016

By Wayne S. Smith, Erik James, Jose R. Gomez

"Soil mixed seepage cutoff walls are increasingly being used in levee and dam modification projects nationwide. An important aspect of their overall quality depends greatly on the language included in the specifications. Depending on the method (e.g. vertical axis auger mixing, cutter soil mixing, or trench mixing techniques) the specifications are a blend of prescriptive and performance based contract language with differences in element construction, element connections, quality control/quality assurance, and work area restrictions. Many of the existing specifications were initially developed by contractors in whole or in part, and can contain restrictive provisions favoring the authoring contractor. In response to these challenges, basic soil mixing fundamentals were revisited and recent lessons learned incorporated, resulting in the development of a new specification for soil mixed seepage cutoff walls that provides adaptability for the various construction methods. The new specification addresses quality control, quality assurance, equipment independence (elimination of restrictive contract language), rig instrumentation.INTRODUCTIONSoil mixing has been used in the construction of seepage barriers for over 30 years. Most soil mixed project primarily use the wet-rotary-shaft, wet-rotary-end or wet-vertical panel methods (reference FHWA Deem Mixing Manual Figure 137). One of the first major soil mixing seepage barriers was constructed in the Jackson Dam in Wyoming. Since then the use of soil mixing for seepage barriers has increased significantly and this specialized domain of construction which was solely procured by RFP methods, is now increasingly being specified in projects issued for bid. The Bid documents require more careful specification writing than RFP methods because the RFP methods allowed detailed proposals by the contractor. Therefore the development of soil mixing specifications began with contractors preparing the specifications. This paper addressed some of these issues, and proposes methods to address these resulting concerns. The resolution of these issues considers several aspects: 1) Assessment of binder injection, 2) Evaluation of mixing index, and 3) Verification testing."

Jan 1, 2016

By John C. Ryan

The Emeca Pile Splice, an innovative mechanical prestressed concrete pile splice, is the first robotically welded splice to be fabricated in the United States. An analytical and experimental study was conducted to establish the capacity of the standard splice for 12-in. and 14-in. square piles. The study illustrates compliance of the splice with International Building Code (2006) requirements. A case study for a large petroleum tank foundation project in Port Canaveral, FL is presented, demonstrating the efficiency achieved through use of spliced-piles. For the case-study project, single-piece 18-in.-square, 100-ft-long piles were replaced with 12-in.-square, two-piece, spliced piles. As a result, a significant reduction of material, labor, handling, and equipment was documented for the project. Savings realized on the installed pile cost was estimated to be in excess of 30% by the owner.

Jan 1, 2010

By Tim Siegel, III Fondren, Billy Camp

"INTRODUCTIONThe new $650 million power block at Santee Cooper’s Cross Generating Station in Cross, South Carolina is being constructed on driven pre-stressed concrete (PSC) piles. S&ME, as geotechnical subconsultant to Parsons Energy and Chemical Group, was responsible for pile analysis and design to meet the site’s geotechnical and seismic challenges. Selection, analysis and design of the PSC piles included consideration of the following:• Column and equipment support loads ranging up to 500 to 1000 kips (2224 to 4448 kN).• Incorporation of the 2000 International Building Code seismic provisions.• A thick upper soft clay and loose, liquefiable sand.• Potential for karst-related features in the calcareous Santee Limestone.GEOTECHNICAL CHARACTERIZATIONThe near-surface site geology consists of (in order of increasing depth): (1) Pleistocene sediments, (2) the Santee Limestone (considered part of the Orangeburg Group) of Eocene age, and (3) the Black Mingo Formation of the Eocene/Paleocene age (refer to the shear-wave profile in Figure 4). Pleistocene clays and silts are generally soft and will settle significantly if subjected to loading by heavy grade-supported structures while the interbedded sands are generally loose. Where submerged below the shallow groundwater table, the sands were determined to be liquefiable during a strong earthquake.The Santee Limestone is a nearly white to yellow fossiliferous and partly glauconitic rock consisting chiefly of calcium carbonate. Observations of the rock core samples from the site indicate that it can range from hard crystalline limestone (primarily in thin layers) to a lightly cemented sand. In terms of rock strength, the Santee Limestone is generally very soft to soft, depending on the cementation and other depositional characteristics."

Jan 1, 2004

By Christopher Sammon, Nicholas Turus

"The demand for underground parking in South Florida has increased as a result of changes to the local building code, coupled with developers’ desire to improve building aesthetics and provide much needed walk in retail space for high-end structures. Historically, underground construction was uncommon in South Florida due to the high groundwater level and porous soil/rock. Conventional dewatering methods become ineffective only a short depth below the ground surface and deeper excavations have required a tremie seal solution consisting of wet excavation and the pouring a temporary unreinforced slab under a water head. However, as excavation area and depth increase, the cost and schedule of the tremie seal method become problematic. For these reasons developers and construction teams alike have looked to contractors in South Florida for alternative means of construction.This paper details the construction of two sites in South Florida where Deep Soil Mixing (DSM) technology offered an efficient alternative to tremie seal construction. The Brickell City Centre required excavation of 8 acres to depths of 30 feet, and augercast piles up to 36” diameter and 110 feet in depth. The second site, Jade Signature, required an excavation of up to 41 feet directly adjacent to the Atlantic beachfront. Due to the concerns over differential settlement, the project featured a soil mixed gravity wall that was designed and installed to allow for completion of the tower prior to excavating the adjacent garage.Both projects involved improving every square inch of ground beneath the planned project excavation. The developed DSM seal slab solution creates a nearly impervious excavation at excavation invert with the strength to resist hydrostatic uplift forces. Low permeability site perimeter walls are constructed to complete the sealed excavation and reinforced with either beams or sheet piles for structural support. Augercast piles required for the permanent hydrostatic concrete slab supplement the uplift capacity of the DSM. After DSM and augercast piles are installed from grade, the site is excavated in dry conditions."

Jan 1, 2017

By Sastry Putcha, Santosh Mummaneni, Avasarala Swamy

"Inspection of bored pile hole bottom prior to placement of concrete is one of the most crucial element of foundation design and construction, especially for end bearing piles. Pile hole bottoms that are not cleaned well for sediments could potentially result in settlement. Although many projects have specifications in-place for drilled pile hole inspection, they are rarely implemented as the current available tools are either unsafe or cumbersome and costly, thus making it very unattractive for owners and contractors. Further, sometimes the post-construction nondestructive quality control testing such as PIT or sonic logging on piles resulted in unanswered questions related to soft bottom. This generates costly disputes with additional testing including concrete coring and possible repairs. Currently, there are several bored pile bottom inspection devices in USA, namely, SID, DID, and SQUID which can either provide video and photo documentation or measure sediments.“ShaftCam”, a patented advanced Digital Borescope, was invented to address the issues related to pile hole bottom inspection with its ability to measure sediments as well as photo and video documentation. Shaftcam device consists of 8-inch diameter bell with a camera, led lights, air hose connection and penetrometer with digital measurement that are connected to a control power box and laptop through a cable. The bell is fitted with a round clear open fiberglass skirt to form an open chamber. A simple motorized winch frame allows the user to lower the ShaftCam equipment gently to the bottom of the shaft at the desired location. Once the bell with camera is lowered to the bottom of the hole, air is pumped into the clear chamber to displace the water/slurry/polymer and get a clear view of the hole bottom to record the conditions and measure the sediment thickness and resistance. The skirt can also be enclosed and lowered to the desired location to allow for inspection of shaft walls.ShaftCam weighs less than 15 lbs. (6.8 kgs) in water and allows for inspection of the hole by one person in less than 30 minutes. Use of ShaftCam has saved significant time and money and thus allowed owners and contractors to readily accept and implement the quality control measures in many projects in USA over past few years."

Jan 1, 1900

By Torsten Wichtmann, Jan Macheck, Frederik Broz, Patrick Staubach, Hauke Zachert

The majority of heavy or strongly loaded structures, for instance high-rise buildings, large span bridges or gas storage tanks are founded on pile groups. However, current design codes and guidelines do not provide a standard procedure for their design under lateral dynamic and high-cyclic loading arising from e.g. wind, temperature or earthquake loads. To establish appropriate design strategies, a better understanding of the pile-soil, pile-pile and pile-cap interaction is required. This paper is focused on finite element backcalculations of centrifuge tests on single piles and pile groups subjected to up to 500 lateral load cycles. For the finite element simulations, a special calculation procedure is applied, combining two kinds of constitutive models, a conventional (Hypoplasticity with Intergranular Strain extension) and a special highcycle accumulation (HCA) model. The parameters of the constitutive models are calibrated based on static and cyclic laboratory tests on the sand used in the centrifuge tests. The performance of the applied numerical procedure is evaluated based on a detailed comparison of the simulation results with the measured data from the centrifuge tests. Overall the applicability of the used numerical strategy for simulating the behavior of pile groups subjected to high-cyclic loading is shown.

May 1, 2022

By Racquel Nottingham, Freddy Lopez, Ole Gadermann

The ongoing urban development is a global phenomenon, placing has high demands on urban infrastructure (housing, public services, transportation, telecommunications, etc.). Micropiling is one of the most successfully implemented deep foundation technologies in urban interventions, and in densely populated and built-up areas. The use of micropiles enabled the implementation of several solutions within short time frames, with minimal disturbance to the daily activities of the population. Since urban interventions usually represent a very important investment and have an economic impact, special attention should be paid to the serviceability of the urban infrastructure in the middle and long term. For the foundations, the design loadbearing capacity of the used structural elements needs to be guaranteed during the planned life time of the structures. In the case of micropiles, it must be ensured that the steel load bearing elements are effectively protected against corrosion. This paper presents the structural design of permanent self-drilling micropiles, subject to tension due to uplift loads. For the case study, different micropile systems - available worldwide - will also be evaluated. For the afore mentioned micropile systems, the design considerations regarding the durability of the reinforcement, based on their corrosion protection approaches, will be presented in this paper.

By Julie Hampden, Tim Dardis, Per Reinhall

"Noise from impact pile driving can harm fish, marine mammals and other sensitive wildlife over large areas. Marine pile driving is highly regulated, and regulators require sound levels to be below certain thresholds to avoid harassment and injury to sensitive marine life. In many locations, timing restrictions, use of noise attenuation technologies and extensive monitoring for impacts to wildlife are also required. As a result, permitting can be laborious and time consuming, and project implementation and scheduling can be complicated. Underwater noise levels are measured with an underwater microphone (hydrophone), which converts noise pressure to voltage and is calibrated to express the noise pressure in Pascals (Pa). The pressure is often expressed using a logarithmic scale, in decibels (dB). Several specific metrics can be used to describe underwater noise. Three common metrics are the instantaneous peak sound pressure level (dBpeak), the root mean square pressure level (dBRMS) and the sound exposure level (dBSEL) referred to as the peak, RMS and SEL levels, respectively.During impact pile driving, the peak pressure represents the instantaneous maximum pressure, either overpressure or underpressure, observed during each pile strike. The RMS level is the square root of the mean of the square of the pressure during the duration of the impulse; it is the average pressure level of the pile strike from beginning to end. The cumulative SEL (SELcum) is calculated by summing the cumulative pressure squared and integrating over time of duration of the pile strike. SEL is used as an indication of the cumulative energy of a pile driving event, which may consist of one or many pile strikes.Regulatory agencies use these metrics to help characterize the noise pressure levels that can affect sensitive species. Some of the most frequently encountered biological thresholds in the Northwestern United States that are used by regulators to describe potential impacts to sensitive species are summarized in the following table. Agencies have defined thresholds for different types of injury, either hearing or bodily harm, and for temporary injury or disturbance."

Jan 1, 2017

By Emre Biringen

Over the past decades, there has been an increasing recognition of the strategic use of pile-supported rafts in design of heavily-loaded structures to reduce total and differential settlements. However, such a hybrid foundation construction method has not been widely utilized in many countries, including the U.S., due to code limitations. In current practice, the foundation design is based on either (i) the bearing capacity of the raft supported by the subgrade soils, or (ii) solely the pile capacity. This paper addresses the potential use of such hybrid piled-raft systems, where the structural load is shared by both by the piles and the subgrade soils directly beneath the raft, in foundation design of power plant structures. The study assessed some of the characteristics of piled-raft behavior by undertaking three-dimensional finite element analyses of two raft sizes, and various pile layout patterns, including the rafts with piles distributed evenly and only in the central area of the raft. The computer software PLAXIS 3D with the Mohr-Coulomb constitutive soil model was used to facilitate the modeling of such cases. The results presented in this paper indicate how strategically locating the piles could reduce the differential and total settlements.

By Dominic Parmantier, Jason Page

"In the past, the designers of DSM have analyzed various failure modes and then specified a minimum unconfined compressive strength (UCS) for the soil-cement. The specified minimum UCS reflected the compressive stress in the soil-cement under design loads and an appropriate factor of safety. With the increased use of finite element analysis for the design of DSM applications where allowable strain as well as stress are considered, there is a growing trend for designers to specify a modulus and occasionally a tensile strength for the soil-cement in addition to the UCS. This paper compares the relationship of modulus and tensile strength to UCS for soil-cement from a recent DSM project with unique testing requirements. These results are compared to published data. The case is made that designers should utilize published relationships to characterize the required strength and stiffness by a single acceptance criterion: UCS.INTRODUCTIONAs the use of DSM has increased in popularity so has the use of service state deformation analysis in lieu of more traditional failure mode analysis. Most DSM designers are interested in the appropriate modulus values and occasionally tensile strength values of soil-cement as well as simply the unconfined compressive strength (UCS) of soil-cement.Although there are numerous published correlations between the UCS, tensile strength and modulus of soil-cement, some DSM project specifications are produced which have acceptance values for tensile strength, modulus, and UCS. If this specification of multiple strength properties is consistent with the nature of soil-cement, then there is really no harm except for the expenditure of client money on unnecessary testing. If however the multiple strength properties specified are inconsistent with the material properties of soil-cement, then the specifications can create the expectation that the DSM contractor can somehow create a custom soil-cement with tensile strengths and modulus characteristics which are unachievable.This paper presents a brief summary of a project in Burnaby, B.C. which specified minimum values for the tensile strength, modulus, and UCS of the soil-cement. A comparison of those test results to published correlations between the UCS and the tensile strength is presented. Additionally, a comparison of modulus derived from two different methods of testing is presented along with a comparison to published correlations between UCS and modulus for soil-cement."

Jan 1, 2015

By R. Lee Wooten, David R. Shields, Darren D. Clark

"Borehole permeability tests that measure flow or head changes in boreholes located within seepage barrier walls are commonly used to estimate the in situ permeabilities of those walls for quality control and assurance. The current state of practice for estimating permeabilities from these barrier wall borehole tests is to use equations published by M. J. Hvorslev in 1951. Hvorslev’s borehole test equations model an infinite stratum of uniform permeability, which is not the actual condition for a test performed in a low permeability barrier wall located within a high permeability stratum. We examine and develop alternative equations based on line source analytical models, which more closely match barrier wall test conditions. We describe how these alternate equations can be used to estimate barrier wall permeabilities from borehole tests and compare the results to those obtained from the Hvorslev models. We also provide recommendations that consider differing upstream and downstream water levels.Barrier Wall Permeability Tests - State Of PracticeThe installation of seepage barrier walls has become more common in a variety of applications ranging from dams and levees to contaminated sites requiring retardation of groundwater flow. The types of seepage barrier walls and installation methods include soil-bentonite, soil-cement-bentonite, concrete, self-hardening slurry, geomembranes, and sheet piles, installed with various soil mixing, slurry-supported trench, and driving methods.Owners and contractors have used a variety of methods to evaluate the permeability of these seepage barriers. The following table lists commonly used quality control/assurance tests for evaluating the permeability of a seepage barrier."

Jan 1, 2016

By Bernard H. Hertlein

The introduction of LRFD methods for structural design has been a gradual process by AASHTO, ACI, AISC, ASCE, and the FHWA, which has largely been ignored by the deep foundations industry. In 2007, however, the industry has been obliged to embrace LRFD for any deep foundations on projects involving federal funds. The authors are concerned that the risks caused by the need for, and the difficulty of providing, reliable quality assurance, will result in unnecessarily high safety factors that will defeat part of the purpose of LRFD. A primary attraction of LRFD for owners and engineers alike is that it promises more efficient design, and therefore cost reductions. Unfortunately, a key element of LRFD philosophy is often overlooked - that the applied safety factors can be rationally reduced, often allowing less material to be used, thus saving costs, but only if all the risk factors involved are identified and closely controlled. This means that both the quality of the materials and the quality of the construction work must be adequately monitored, and held to an acceptable standard. In the case of deep foundations, the soil in which the foundation is constructed is also a critical component that must be taken into account in the assessment of risk factors.

Jan 1, 2007

By Donald A. Deardorff

The capacity of a helical pile can be determined analytically using the individual bearing or cylindrical shear methods which are dependent on soil strength parameters and helical bearing area. The torque correlation method is widely used in the helical industry to determine the capacity during installation by monitoring torque during the final seating of the helicals. This method has been shown to be a better predictor of strength than the individual bearing or cylindrical shear methods. To determine capacity using the torque correlation method, the final average installation torque (ft-lbs) is multiplied by an empirical torque correlation factor (Kt, ft-1). Kt values have been well documented for square bar shaft helical products and can vary from about 3 to 20 ft-1 depending on pile geometry and soil type. A default value of 10 ft-1 is generally used for all square shaft sizes and soil conditions. Less research has been done on determination of Kt for round pipe shaft helical products. Studies have indicated that factors which affect Kt include soil type/strength, number of helical plates, helix spacing, helix pitch, depth of embedment, downward pressure (crowd), shaft diameter (round pipe) and load application direction while other studies have discounted some of these factors as inconsequential. This paper reviews past research findings regarding Kt determination for square and round pipe shaft helical products and presents a case history of round shaft helical pile installations in Chicago clay which resulted in much lower than expected Kt values.

Jan 1, 2007

By Paul Doherty

The offshore wind sector is booming on a global scale, with the U.S. becoming a front runner in this highly progressive market. The Global Wind Energy Council has highlighted the exponential growth in both fixed bottom and floating projects in the years ahead, with global installed capacity set to exceed 300 GW by 2030. This growth in installed capacity is primarily related to fixed bottom projects, which have dominated the market for the past 20 years. However by the tail end of this decade, floating projects are likely to become

Oct 1, 2022