Search Documents

By Gurupraveen Ramanathan

Shallow-dipping orebodies (45°–60° dip) present significant challenges for underground longhole stoping, particularly due to limited gravity flow, drill misalignment near the footwall, increased potential for dilution from hanging wall overbreak, and deviation from drill string sagging at shallow angles. These geometrical and operational constraints often lead to unblasted ore wedges and excessive overbreak when standard practices are applied. This study develops a structured, data-driven framework to optimize longhole stoping in such conditions by integrating five key focus areas: (1) mining method selection, (2) stope and drift design, (3) drill and blast optimization, (4) equipment selection, and (5) performance evaluation. The suitability of longitudinal longhole stoping was validated for narrow vein geometries using orebody analytics and prior case studies. Geometric modeling was employed to determine optimal stope height (15–20 m) and stope width (1.5–2.5 m), with drift widths adjusted based on orebody dip to maintain drill access and minimize unbroken ore. Drill and blast design emphasized sequential blasting over multi-ring methods to improve void control, reduce wall damage, and enhance fragmentation. Specific burden and spacing guidelines (e.g., 1.8–2.3 m burden; 2.5–3.0 m spacing) were applied based on stope width and dip angle, and patterns were selected based on geometry—dice-5 for narrow stopes, and 3-hole rows for wider stopes. Drill rigs—including top hammer and ITH models from Sandvik, Epiroc, Boart Longyear and CMAC-Thyssen—were evaluated for compatibility with drift dimensions and alignment accuracy. Equipment was matched based on dip, drift width, and the ability to access the footwall at shallow angles. Sensitivity analysis quantified how changes in geometry, drilling accuracy, and blast design affect ore recovery, dilution, and operating cash flow. Results show that tailored drift and stope geometries, combined with proper blasting and rig selection, can boost ore recovery to over 95% and reduce dilution to below 5% in optimal conditions. This methodology offers a practical and economically optimized solution for shallow-dip mining scenarios.

May 4, 2025

By H. Sahay

"DISCLAIMER NOTICEThe views and conclusions contained in this presentation are those of the author and should not be interpreted as necessarily representing the official policies or recommendations of the Department of Mines and Energy, Government of Newfoundland and Labrador. ABSTRACTThis paper describes the main testing procedures that should be carried out to evaluate the capacity and capability of the service brakes on the large-size diesel-electric trucks now in common use at open-pit mining operations. Brake testing programs in general are described, and then consideration is given to different techniques of service brake testing, brake performance evaluation, braking energy and typical performance characteristics.IntroductionThe first diesel-electric truck with a capacity of about 85 tons was introduced in 1963 by Unit Rig and Equipment Company of Tulsa in cooperation with General Electric Company, who successfully developed and supplied the most important component- motorized wheels. Since then, its popularity and numbers have continued to grow, and now more than 3700 such units are in operation in mines around the world. In Canada alone, their number is more than 700, including about 150 in the Province of Newfoundland and Labrador. Similarly, their size has also grown from that initial capacity of 85 tons to 350 tons.Although the introduction of the electric trucks proved to be invariably economical, their indiscriminate use was not without severe consequences. Many runaways and even fatalities occurred when the dynamic retarder failed while the truck was travelling loaded down severe grades. The service brakes in such cases proved incapable of stopping runaway trucks, mainly due to their limited capability and the fading caused by excessive heat produced during the act of braking itself. This eventually led the various governments, the open-pit operators and the manufacturers to seriously question the braking capability as well as function of both service brakes and dynamic retarders. Extensive testing"

Jan 1, 1980

By R. A. Hemstock

AREAS in which the surface de-posits consist of organic material -known in some parts of Canada as muskeg and in Europe, more generally, as peat lands -have long been some of the least rewarding of lands of the north temperature zone. Even in such countries as Great Britain, Holland, and Denmark where a good deal of incentive exists to develop all available land, the use of peat land has been negligible except as a source of fuel. Only recently have efforts shown promise in re-claiming these lands for farming or for forestry. Russia has large areas of peat and use is made of it for power generation. The Russian people have also ?developed a variety of machines for handling peat, which would indicate that they are well ahead of the Wes tern World in their technical and physical ability to solve some of the problems. Certainly in Canada, where there are over 500,000 square miles of muskeg, the economic aspects of this problem are important. This is especially true in considering the shifting emphasis to northern development. Not only is muskeg in possession of great stretches of terrain, thereby rendering it useless for agricultural purposes, but it is apparently moving into forested areas and reducing their productivity. In addition, it lies as a great barrier to movement in the search for and development of such natural resources as petroleum, natural gas and minerals generally. This situation has long been recognized in Canada but only recently have organized efforts been made to study the problems and search out ways of overcoming them.

Jan 1, 1958

By D. B. Dreisinger, M. Mokmeli, B. Wassink

Dissemination of selenium and tellurium in sulphide minerals results in the contamination of pregnant leach solutions and electrolytes in the hydrometallurgical treatment of sulphide ores and residues. The selenium and tellurium content of the copper sulphate-sulfuric acid solution may be reduced into insoluble precipitates of copper selenides and tellurides using cuprous ion. This study presents the use of the thermodynamics and kinetics for the removal process of selenium and tellurium in real life application. Dominant species of selenium and tellurium in acidic copper sulfate solutions were identified and the reduction rates of species were compared. The findings were applied to industrial conditions by modeling the Vale’s CRED (Sudbury, Canada) plant’s selenium and tellurium purification circuit. Rate reducing factors on selenium and tellurium removal were identified and discussed.

Jan 1, 2014

By Jörgen Appelgren

Atlas Copco, a leading supplier of equipment and services to the mining and construction industries, is consistently pursuing its strategy to offer the most productive and economical solutions by continuously offering new innovative products. These are in most cases developed and tested in close cooperation with demanding end users before being officially launched on the international market. The demands for higher productivity and improved overall economy have resulted in systems for automation of the drilling cycle and also tools for integrating the Drilling equipment to the production control system used by the customer. In terms of improving the blasted material quality, Atlas Copco has placed emphasis on hole straightness and the need for hole logging and positioning. By applying state of the art technology to today?s computerized drilling rigs, major steps in improving overall drilling and blasting performance have been achieved. This paper will give some examples derived from the latest development of solutions for the Rotary drilling product line.

Oct 1, 2009

By J. W. Smith, J. Van Dusen, A. Papachristodoulou

"As part of a study to evaluate factors affecting tankroom air quality, the mechanism of aerosol generation from bursting bubbles in electrowinning operations has been investigated. Typically 2 to 3 mg/m2.s are produced in zinc tankrooms. Analysis shows that the rate of production of film drops (geometric mean diameter - 2 urn] increases with decreasing bubble size, and that jet droplets (geometric mean diameter - 20 um) are not produced with gas bubble larger than - 4 mm. Both mechanisms of drop formation and current efficiency are affected by surface active agents, with an over-all reduction in emission of up to 60% to 70% being achievable. A source control system which does not adversely affect electrolyte properties is always preferred, and coalescence of all gas bubbles in to a continuous stream of gas at a single point on the electrolyte surface would eliminate aerosol emissions. This objective was the basis for design of a coalescence device which, in laboratory tests, reduced the emission rate by over 95%.The control device fit s over the electrodes in the electrowinning cell and is partially immersed in the electrolyte. A number of changes in the design which resulted in significant improvement in the performance of the device are reported.Field tests have shown that only about 75% of the aerosol below 10 um can be eliminated by coalescence. The remainder (up to 95% of the total) is controlled by coalescence of droplets, by impaction on the exposed collector surface and gravitational settling.The device does not interfere with operation of the tankroom, handles the effect of surges in power during harvesting, and is simple and inexpensive to maintain. IntroductionDuring the electrowinning of metals (such as zinc and copper) gases are evolved along the electrode surface forming small bubbles. The bubbles travel upwards and burst on the electrolyte free surface generating, in this way, small droplets. Because the electrolyte is often highly acidic or contains toxic materials, the whole process can result in the formation of an aerosol in the atmosphere above the electrowinning cells which poses a serious health hazard to workers in the area, and corrodes equipment."

Jan 1, 1988

By W. J. Wolfe

"Quartz Hill is a large, low- to moderate-grade quartz vein stockwork porphyry molybdenum deposit, discovered in 1974 during a regional stream sediment geochemical reconnaissance survey of southeast Alaska conducted by United States Borax and Chemical Corporation. Mineralization is localized in the upper parts of an Upper Oligocene (30 Ma) composite quartz monzonite stock which is emplaced discordantly into older Cretaceous to Early Tertiary terrain of the Coast Range igneous metamorphic complex of the northwest North American Cordillera. Subsequent fault-controlled, complex multi-stage intrusion, concentrated in the core of the Quartz Hill stock, produced successive pulses of hydrothermal alteration and molybdenum mineralization at about 27 Ma. Overall, the deposit is tabular and flat-lying and well suited to open pit mining. The 0.05% MoS2 grade limit covers an area of approximately 1500 m by 2750 m and extends to a maximum depth of 520 m below surface. Details of grade distribution show two separate lobes of higher grade material within the larger low-grade deposit.A ten year program of exploration drilling, underground development, sampling and metallurgical testwork led to a 1983 feasibility study based on a resource of 1600 million tonnes grading 0.127% MoS2 at a 0.08% MoS2 cutoff The large size of the deposit and its homogeneous grade distribution, typically showing gradual outward decrease of grade, makes in pit grade selection practical at several cutoff levels. Cominco Ltd. now reports a Probable Resource of 210 million tonnes averaging 0.22% MoS2 with a further Possible Resource of 1100 million tonnes averaging 0.12% MoS:z. At low molybdenum metal prices which have persisted for 10 years since the molybdenum price spike of the late 1970s and early 1980s, the Quartz Hill deposit is sub-economic."

Jan 1, 1995

By A. G. Ballachey

Introduction This paper will describe the mining plant and underground operations at Quemont. Details of geology and milling are beyond its scope. Papers on these subjects will be prepared and presented separately. A detailed account of the exploration and development, 1944 to 1947, has been given by W. L. Brown (1). Location The mining concessions of Quemont Mining Corporation, Limited, are in Rouyn township, Rouyn-Noranda county, northwestern Quebec. These concessions total about 640 acres in area. They lie within the limits of the City of Noranda, contiguous to, and directly north of, the Horne mine of Noranda Mines, Limited. A large area in the southern part of the property is covered by the north arm of Osisko lake. Production The present operating rate is about 2,100 tons per day. Three flotation concentrates are produced: copper, containing a large proportion of the gold and silver in the ore; zinc; and pyrite, which carries an appreciable additional proportion of gold. The copper and zinc concentrates are shipped to smelters as produced. The pyrite concentrate is cyanided to recover additional gold, after which it is filtered, dried, and shipped for the manufacture of sulphuric acid. The principal revenue metals are copper, gold, and zinc. Silver and pyrite are important by-products.

Jan 1, 1952

By Sunil S. Gandhi

"The Mountain Lake deposit is a tabular sandstone-type uranium deposit, hosted by the basal unit of Middle Proterozoic Dismal Lakes Group. Uranium occurs mainly as sooty pitchblende disseminated in stratiform lenses within gently dipping quartzose sandstone. It is associated with copper sulphides, pyrite, hematite, and traces of nickel and cobalt arsenides and of silver.Exploration HistoryUranium showings on the PEC claim group were discovered during 1969 by an airborne radiometric survey carried out over the Dismal Lakes-Great Bear Lake area by Aquitaine of Canada Limited (Bizard and Salat, 1969). Some drilling was done in the vicinity of the showings in 1975 by the company under a joint venture with Eldorado Nuclear Limited but the results were not encouraging (Hassard and Woollett, 1975). During 1972, Trigg, Woollett and Associates Limited conducting surveys for Imperial Oil Limited, discovered numerous high-grade radioactive boulders scattered over a distance of several kilometres north and west of the showings, and the area north of the PEC claims was staked as the YUK claims (Ahuja, 1974). A systematic study of the boulder distribution and Pleistocene geology suggested a source additional to the showings. More intensive exploration followed, and in 1976 drilling just north of the PEC claim group boundary intersected the main deposit at a depth of 75 m to 150 m, beneath overburden up to 60 m thick. Part of the deposit extends into the PEC claim group which is under exploration by the Aquitaine-Cominco Joint Venture.The following brief description is based on the presentations in 1978 by F. Hassard of Trigg, Woollett and Associates Limited at the Geoscience Forum in Yellowknife, and by S.S. Gandhi of the Geological Survey of Canada at the Mineralogical Association of Canada Uranium Short Course in Toronto."

Jan 1, 1986

By W. Harry Foster

"Asbestos Corporation Limited, incorporated in 1925, operates four asbestos mines and three asbestos mills in the Thetford Mines 1•egion of Quebec's Eastern Townships. A unique asbestos orebody, located in the Ungava Peninsula of Nouveau Quebec, was purchased by Asbestos Corporation Limited in 1964 and commenced production in 1972. As there were no existing facilities in the isolated, arctic region of Asbestos Hill, it was necessary for Asbestos Corporation Limited to construct at Deception Bay a deepsea wharf, a large ungraded fibre shed, a power plant and camp facilities. Forty-two miles of road were needed and were constructed from Deception Bay to Asbestos Hill. At Asbestos Hill, a complete crushing-drying-milling complex, a power plant, pe1•sonnel accommodations and open-pit facilities were provided. Unloading facilities and a fib1•e finishing mill we1l constructed at Nordenham, West Germany. The ""Asbestos Hill- Nordenham Story” is divided into individual papers covering all aspects of the engineering, construction and operation of this unique enterprise. Particular emphasis has been placed on those unusual aspects caused by the isolated location, arctic conditions, short shipping season and the deep permafrost."

Jan 1, 1976

By Judith S. Chan

With the increasing awareness of the need for the reduction of carbon emissions globally, geothermal energy, which offers a potential for cleaner energy generation, is one potential new source. In Alberta, these geothermal resources are likely to be found in the sedimentary basin, or in the deeper crystalline basement rocks. Alberta exhibits a very low geothermal gradient compared to other existing geothermal fields located in areas of volcanic and tectonic activity. To mitigate this effect, the focus in Alberta will involve the development of engineered geothermal systems (EGS) in the target resource. The first goal for EGS research and development is to develop a detailed geological-geophysical characterization of selected sites to delineate potential geothermal reservoirs in Northern Alberta. One of the selected sites is in the Fort McMurray area. The deepest well drilled in the oilsands areas of Northern Alberta is located just west of Fort McMurray. It has a depth of 2363 m and as such can provide details on the physical properties of the rocks, the state of stress, and the existence of fracture porosity toward geothermal investigations. To date, we have acquired temperature logs to study the change in geothermal gradient with depth, and a series of petrophysical logs to study the finer scale structure of the rock formations with vertical resolutions in the range of 0.05 cm to 80 cm. Our aim is to identify geological features such as zones of fractures in the basin and/or basement that could provide an indication of enhanced fluid flow potential ? a necessary component for any geothermal systems to be viable. Zero offset and walkaway vertical seismic profiles (VSP) were also conducted to measure the seismic responses at the borehole. VSP data can be used to delineate the structural and stratigraphic features surrounding the borehole that could not be resolved from surface seismic reflection data that are also available near the borehole. The full integration of well logs, VSP data and surface seismic reflection data are expected to provide a detailed characterization of the sedimentary basin and crystalline basement rocks of the Canadian Shield in Northeastern Alberta and will assist in future planning for drilling.

Jun 1, 2012

By B. M. Das, F. Claridge, V. K. Garga

Coal, as well as a large part of other minerals in Canada, is produced by surface mining methods. This has resulted in short and long-term accumulation of waste rock in dumps. Two main problems arise from the flow of water through these dumps: stability of dumps and the impact on stream flows. In recent years, a number of mines have started placing waste rock in valleys for general disposal or far constructing mine access road ways. All these have created challenges in the following areas: effective design of dumps and flow-through dams; stability monitoring of the structures; environmental impacts downstream by way of increased amount of fines in suspension, sedimentation, and toxic substances; and long-term status of flow and flood. Similar situations also exist in many civil engineering structures. This paper discusses the status of rock drains and the immediate and future research needs.

Jan 1, 1990

By Jack A. Caldwell

"This paper describes the nature of stage curves and the ways in which they have been used to study the construction sequencing of tailings impoundments. They provide a simple graphical method of representing the main aspects of an impoundment, studying the effects of different impoundment geometries, and predicting and controlling impoundment operations.IntroductionThe designer o f a tailings impoundment must, at all stages of design, examine the relations hip between the volume o r tones of tailings that will be deposited at the impoundment, the height to which the tailings will rise in a given time and that rate at which the various parts of an impoundment will be constructed. The operator, if he is to keep proper control of this impoundment, must be able to examine the effect of different deposit ion rates at the impoundment, and the consequences of placing more or less tailings at different parts of the impoundment. The operator must be able to see at a glance just how much higher an impoundment will be at the end o f the following yea r of deposition, and this he must be able to do in order to formulate his annual construction and operating plans.Stage curves are the best way o f modeling an impoundment. The simple impoundment model represented by the stage curves enables the designer and operator visually to examine the relationships between the various factors, such as impoundment volume, deposition rat e and construction rate, that dictate the essential features o f impoundment design and operation.A design model for a tailings impoundment may be formulated as in Figure 1. This involves the site selection process, the definition o f a geotechnical model, a water balance model and a height-capacity-production model."

Jan 1, 1983

By K. Soldenhoff, D. Wilkins, E. Ho

In the processing of rare earth ores, a pure, mixed rare earth chloride solution is usually produced and used as the feed to solvent extraction circuits to separate the individual rare earths. Cerium(III) may be separated from the other rare earths by oxidising it to cerium(IV), which precipitates as cerium(IV) hydroxide in chloride liquors. This oxidation step may be inserted either before rare earth separation by solvent extraction or between solvent extraction circuits. Although oxidation of cerium by sodium hypochlorite has been known for many years, detailed conditions for oxidation are not readily available. The effect of hypochlorite addition, temperature, pH and cerium concentration on oxidation of cerium(III) from synthetic solutions was investigated

Jan 1, 2014

By T. R. C. Aston, C. M. K. Yuen, J. L. Gilby

"The access tunnels for the Donkin-Morien Mine in Cape Breton, Nova Scotia, comprise two parallel tunnels driven through a sedimentary sequence of sandstone, siltstone and mudstone to intersect the Harbour Coal Seam under the Atlantic Ocean, approximately 3.5 km offshore (Fig. 1). The No. 2 tunnel was driven a total distance of 3579 m using a 7.6 m diameter Loyat full-face tunnel boring machine (TBM) and was supported by steel sets. The No. 3 tunnel was initially driven a distance of 1027 m using drill and blast methods (dimensions 7.6 m wide by 5.3 m high) supported by rock bolts and shotcrete. This tunnel was then completed (front March 1986 to February 1987) using the tunnel boring machine to a distance of 3573 m.During the period May 1983 to December 1984, a major geotechnical research program was undertaken in the Donkin-Morien tunnels by Golder Associates in conjunction w,ith CANMET and the Cape Breton Development Corporation (Yuen et al., 1985). The research program included the monitoring of the performance of the TBM and drill and blast drivages, and the study of the thrusting characteristics and rock-interaction of the TBM excavation. The main emphasis of the research program was on the collection of field data which was to be made available in the form of a comprehensive report for the future use of others who might wish to carry out a detailed interpretation and analysis. The information gained from the program was also used during the tunnel"

Jan 1, 1988

By C. A. Roloff

Demands for increased grinding production, lower-grade are and limited capital have resulted in ever larger grinding mills, some as large as 36ft (/1 m) in diameter and 12,000 hp (8,950 kw). The result is often f ewer machines per plant, with a greater dependence on each machine. To meet these reliability requirements, manufacturers of mills, drives, castings and other components have had to be innovative and creative in their design. Only by thorough review of past designs and practices and by model studies confirmed in field tests can the manufacturer have full confidence in the product. Because of the great interest in large mills, a short review of larger machines is presented. This discussion covers material feeding, bearings, the rotating element, drive trains and material discharge.

Jan 1, 1979

By H. Wotruba, J. Heizmann

"The use of shotcrete is a mandatory means for rock support and therefore for safety in many underground mining operations. If shotcrete gets into the flotation feed though, it can negatively influence the flotation process. This especially occurs when sublevel stoping, cut-and-fill or room-and-pillar methods are applied because as the mining face moves on, formerly applied shotcrete layers are mined together with the ore.As shotcrete does not differ significantly from fluorspar ore in its physical properties it gets moved through the comminution process and is fed to the flotation plant like the ore. To prove the influence of shotcrete on the flotation process, a laboratory test series was conducted at the Unit of Mineral Processing (AMR) of the RWTH Aachen University. The shotcrete grade of the flotation feed was varied between 0 and 10% through addition of pure shotcrete. Flotation parameters and also reagent dosage were held constant apart from the addition of the pH regulator, which was dosed to reach a constant pH of 8 at the flotation start. Results showed that with increasing shotcrete grades in the flotation feed the fluorspar recovery as well as general mass recovery decreased. The enrichment factor of Fluorspar also decreased with increasing shotcrete grades in the feed.In an effort to eliminate the shotcrete contamination of the flotation feed, a feasibility study for use of sensor-based sorting prior to the comminution process was conducted. Rock sorting not only reduces the bad influence of shotcrete on the flotation process, but also reduces comminution costs. INTRODUCTIONShotcrete is used in underground mining on a regular basis. It is used for rock support and therefore to increase safety in the underground mining environment. In mineral processing the presence of shotcrete can cause difficulties for example in the concentration processes. In flotation the highly sensitive reagent mixtures can be disturbed by the chemical activity of shotcrete and therefore recovery rates and selectivity of the process can suffer.Shotcrete is a special form of concrete which is applied pneumatically with high velocities and is compressed by its impact energy. Since the process is especially suitable for work in difficult environments and overhead areas, it is established in underground mining for many years. Shotcrete is not only applied in pre-processing of the mines, but particularly of use for cut and fill, as well as room and pillar mining methods. There it is used to secure excavation chambers. When the mine face is secured with shotcrete and subsequently the mining continues, the applied shotcrete will automatically be mixed with the ore."

Jan 1, 2016

By Arthur L. de Carle

"IntroductionThe Key Lake uranium-nickel deposits are located within a Mineral Lease centred at latitude 57 ° 12' north and longitude 105 °39' west along the southeastern rim of the Athabasca sedimentary basin in northern Saskatchewan, approximately 240 km north of La Ronge (Fig. 1). Access is provided by an allweather provincial highway from Pinchousc, situated about 200 km to the south, and a private airstrip maintained at the mincsitc.These deposits have been developed by Key Lake Mining Corporation on behalf of the Saskatchewan Uranium Joint Venture. Participants in the joint venture include Saskatchewan Mining Development Corporation (50%), Urancrz Exploration and Mining Limited (33 1/3 %) and Eldor Resources Limited (16 2/3 %).Considerable geological work has been conducted on the Key Lake orebodies and reported in summary papers published by Dahlkamp and Thn, (1977), Dahlkamp, (1978), Gatzweiler eta/., (1979) and Kirchner el a/. , (1980). However, intensive geological research is ongoing, particularly since many problems regarding ore genesis and controls remain unresolved . Exploration History and DevelopmentThe events (Gatzweiler eta/., 1980) which led to the discovery of the Key Lake ore bodies began in the summer of 1971 by following up on the reports of airborne radiometric anomalies and anomalous radon values in the Zimmer Lake water situated approximately 5 km to 6 km to the southwest. This work succeeded in locating a few high-grade uranium and nickel-bearing boulders associated with esker material. An integrated program, consisting of various geochemical and geophysical surveys along with diamond drilling, culminated in the discovery of the Gaertner orebody during July 1975. Subsequent fence drilling across the strike extensions of this ore structure located the Deilmann deposit, approximately I km to the northeast, in June 1976"

Jan 1, 1986

By J. M. Carr

The history, geological setting and local geology of the Magnum vein system, 100 miles west of Fort Nelson in northeastern British Columbia, are described. The system comprises a number of quartz-ankerite veins, mineralized with chalcopyrite and lesser pyrite, occurring in a steep northeastly zone of deformation and subsequent dike intrusion within otherwise little-deformed Precambrian sedimentary rocks. In April of 1970, Churchill Copper Corporation began producing copper concentrates in a 750-tpd mill fed from the Magnum mine.

Jan 1, 1971

By E. Ghali, J. F. Dorion

This paper presents the results of on-going investigations on the influence of corrosion on the performance of support systems in selected underground gold mines. Rock support is exposed to various conditions that can be aggressive. Samples of corroded support were analysed using SEM and photomicrography to determine the main corrosion forms. Tests are on-going in controlled corrosion chambers to qualify and quantify the impact of rock and minerals particles on steel corrosion. As more data become available these relationships can lead to useful information on the choice of support systems and reliable estimates of their longevity.

Jan 1, 2011