Search Documents

By G. Wren

As base metal sulphide resources become increasingly challenging to process, producers seek alternative options to treat concentrates. This study considers the mineral, elemental, and leaching character of a West Australian nickel sulphide deposit (Cosmos Nickel Project). After a brief review of the published work bench top leach tests were conducted to examine the factors which impact the kinetics of nickel sulphide leaching such as particle size, temperature, acid strength and type, concentration of copper sulphate and sodium chloride, and oxygen partial pressure. The effect of sodium chloride was considered due to the common occurrence of hyper saline water at West Australian nickel sulphide mine sites. Ultrafine grinding to an 80% passing size of 10 µm resulted in high nickel leaching efficiency. Moreover, higher concentrations of acid, copper(II) and sodium chloride also gave higher nickel and cobalt leaching efficiencies but arsenic precipitated as FeAsO4. Under the most suitable conditions the extractions of nickel, cobalt and arsenic at 90oC after 6 hours were >95%, 90% and <5%, respectively. The comparison with results from high pressure operations indicates the possibility of using a hydrometallurgical flowsheet based on fine grinding and atmospheric pressure leaching and warrants further investigations.

Jan 1, 2014

By A. Desbiens, A. Pomerleau

During the summer of 1994, a new PID-based control strategy was installed on line B of the grinding circuit at the Kidd Creek Division of Falconbridge Ltd. Part I of this paper described the methodology used to select the appropriate control strategy using a phenomenological dynamic simulator. Part II presents the implementation of the control strategy. Prior to the controller installation, it was necessary to solve various problems related to the process, such as a cyclic behaviour of the rod mill feed tonnage, a problem related to the mill water source and the calibration of the flowmeters. Once these problems were solved, the control strategy was accomplished in two steps. Step 1 corresponds to the installation of control loops to regulate the pump box level and the cyclone overflow density. Step 2 describes the implementation of a loop to control the cyclone feed density. According to Part I, a loop to control the circulating load is also part of the original design. However, reasons are given to explain the rejection of this loop. For both steps, technical procedures such as filtering, process identification and controller tuning are detailed. Finally, the operator’s interface is briefly described.

Jan 1, 1997

By Geo. E. Cole

A GREAT deal of time and energy is now being devoted to the study of post-war reconstruction and rehabilitation, in spite of the fact that as yet we have not won the war in which we are presently engaged. If you feel that the study of post-war problems takes our thought away from the problem immediately before us, you may well query, "Well! What has all that to do with winning the war, our most urgent problem today?" The answer has been given by Principal James of McGill University, Chairman of the Cabinet Committee on Reconstruction: "Reconstruction is something which must be thought of in advance, partly for the purpose of recognizing exactly the influence of war-time activities, controls, and regulations on the post-war Canadian scene. Many people are acutely interested in this great problem. It is not that they are not interested in the war itself, or epochal events that are taking place from day to day. They have a vision of that future which they hope will be Canada&apos;s, and this vision inspires them to even greater efforts at the present time". The trend of events would indicate that changes, economic and industrial, after this war will be greatly out of line with those that followed previous wars in history, for the present struggle has involved every nation in the world. In the peace that will come, every engineer will have a task in bringing the most desirable order out of the most distressing chaos. We certainly are living in a changing world; we are witnessing geo-graphical and economic readjustments that no other generation in world&apos;s history has ever witnessed. And there is an opinion gaining strength in our Dominion, as in other lands, that after this war we shall live in a world in which our process of thinking and our very way of life will have to undergo drastic changes to cope with the new order of things. Sadly our world of today has had to revise the sublime vision that nation shall not lift up sword against nation, while salvage operations continue to beat ploughshares into tanks and the peaceful pruning-hook into a weapon for the deviltry of the commando.

Jan 1, 1943

By D. Holz

In this work we present a novel level set-based model for the real-time simulation of soil deformations. A level set defined by a signed distance function and sampled in a regular 3D grid represents and tracks the soil volume under deformation. Moving away from classical 2.5D heightfield representations of soil to a full 3D volume representation allows for improved tracking of cutting tool operations and the simulation of near-vertical or vertical soil faces. The proposed level set representation furthermore provides a versatile mathematical platform for modeling additional effects such as soil slip, and does not suffer from the sampling limitations of commonly used heightfields. Cutting forces applied to the tool are simulated via a formulation based on the Fundamental Equation of Earthmoving, modified to support inclined soil surfaces and transient states of tool motion. Discretisation of this 2D cutting force model with respect to the tool surface allows capturing the effects of irregular 3D terrain shapes on blades and buckets. The surcharge created during cutting operations is tracked in the form of particles and included in the soil failure force computation. We make use of an adaptive, hybrid level set-based and particle-based soil deformation scheme, which allows the soil deformation to be simulated in real-time.

Aug 1, 2013

By M. H. Rana

"A survey of our knowledge in the field of rock mechanics is presented from the viewpoint of applications in the mining industry. Aspects of rock mechanics of special interest to the industry are enlarged upon, with emphasis on the avoidance of over-generalization. The relationship between fundamental and practical rock mechanics is discussed, and the need for cooperation between the university and industry to further our knowledge of -useful rock mechanics is emphasized. An attempt has been made to establish the scope of rock mechanics, as applied to problems in the mining industry. This is brought about by projecting rock mechanics as a tool to be intelligently used rather than magic, capable of producing ""miracles."" Continued education is important for individuals engaged in the application 0f rock mechanics in the mining industry. The scope of this education is discussed from a viewpoint of better communication between industry and the education and/or re-search establishments engaged in this work.Finally, the dangers of over-emphasis on rock mechanics are mentioned, but a justification of the in-vestment in rock mechanics programs in mines is also presented."

Jan 1, 1966

By L. Paulino, C. E. Zangiacomi, J. Yamamoto

"This paper presents the learning from Alcoa Po9os de Caldas Smelter in Brazil, after several energy restrictions resulting from the failures of three rectifier units at its power switchyard. Starting on December 27th, fuses and diodes failed in three rectifier units of Potline #1, causing a long and dangerous power interruption. Even after current was reestablished, amperage was only 70% of the line target leading to a bath freezing process that lasted for around 48 hours. The process engineering team played with several potroom parameters as pot resistance, bath and metal levels, alumina feeding and bath chemistry in an attempt to minimize impact on the potline metal output and energy consumption. As it will be illustrated, the first battle was to keep the pots running on a ""survival"" approach. After that, several changes took place on the procedures used to run at reduced current which were considered rather successful. Finally, some recommendations will be given to foresee and prevent transformers and rectifiers from undesirable failures."

Jan 1, 2006

By Rodney A. Cooper

The Mary River iron ore deposits were discovered in the 1960?s. The high quality of the deposits was immediately evident, and drilling programs were successful in defining a resource adequate for supporting a feasibility study. Through a combination of ownership, market and political forces, the deposits were not developed. Having missed the window of opportunity, the project remained dormant for over three decades. Baffinland Iron Mines Corporation, with its 100% ownership of the Mary River deposits, began trading publicly in 2004. Modern exploration and metallurgical test work began in 2004 and has continued in 2005 and 2006, resulting in total expenditures during this period of almost C$60 million. In May 2006, an engineering team lead by Aker Kvaerner E&C, a division of Aker Kvaerner Canada Inc., completed a scoping study based on the first of five identified deposits. Highlights of that study include direct shipping of high quality lump ore to Europe over a 34 year mine life at a production rate of 10 million tonnes per annum, based on an indicated resource of 309 million tonnes at 66.1% Fe and an inferred resource of 28 million tonnes at 65.9% Fe. Capital costs were estimated at C$1.5 billion. Using iron ore prices approximately 36% below that of the 2006 market, a pre-tax internal rate of return of 15% was estimated assuming equity financing. Payback on initial capital was 5.9 years. The pre-tax life-of-mine cash flow was estimated to be C$6.3 billion. As a result of this study, Baffinland initiated a Definitive Feasibility Study, under the management of Aker Kvaerner, which is scheduled for completion in December 2007. This paper touches on the geology of the deposits, the current resource and the outlook for expansion. Project permitting, construction planning, logistical challenges and ocean shipping considerations are discussed, providing a current perspective on the project scale, scope and timeline for commercial production. In addition, an overview of the Company?s bulk sampling program will be provided.

May 1, 2007

By P. C. Lightfoot, J. M. Duke, A. J. Naldrett

"The segregation of magmatic sulphides from mafic and ultramafic silicate magmas, in many circumstances, leaves the magma with a lower-than-normal Ni/MgO ratio, which is characteristic of both lavas erupted from the magma chamber and olivine crystallizing within it. Two end members of the segregation process are discussed; i) batch segregation and ii) fractional segregation.In the former, the critical factor is the magma/sulphide ratio. Computer modelling suggests that where this ratio has been less than 1000, the magma will be recognizable as anomalously low in Ni, due to sulphide segregation, and thus a good target for exploration. In fractional segregation, the critical factors are the proportion of sulphide to silicate being segregated and the degree of fractionation.Samples believed to represent the liquid portion of komatiitic lava f lows from a series of unmineralized sequences in the Abitibi greenstone belt, Canada. Belingwe belt, Zimbabwe, and Barberton Mountainland, South Africa coincide with the sulphide-free fractionation model. They are in marked contrast to samples from the ore-bearing districts of Kambalda and Scotia. Western Australia in which distinct Ni depletion, corresponding to fractionation of olivine plus sulphide in a ratio of between 100 and 200:1 is recognizable. Ni-depleted olivines also mark the sulphide-bearing Dumont intrusion of the Abitibi belt.The Moxie intrusion of northern Maine has distinctly Nidepleted olivines, as does the nearby and petrologically related Katahdin body. In both of these intrusions, the composition of the olivine allows reasonable predictions to be made of the Ni tenors of sulphide showings within them. At Katahdin, the Ni depletion is so widespread that little hope is help out for the presence of economic concentrations of sulphide. At Moxie. the olivine compositions suggest that the best chance of economic sulphides lies in the southern lobe of the intrusion.Ni-depleted olivines also characterize certain rock units within intrusions of the Insizwa complex, Transkei, Southern Africa. Many millions of tonnes of Ni have apparently been removed by sulphides from these rock units, many more than are contained within the single mineralized occurrence so far identified at Waterfall Gorge."

Jan 1, 1984

By Toivo Toivanen

The paper begins with a brief history of the nickel industry in Finland, and then deals with the introduction of the flash smelting process. The main part of the paper is devoted to nickel refining, which is studied under four main headings -grinding, leaching, electrolyte precipitation, and nickel electrowinning. Flowsheets are illustrated, and the equipment used is described. Analyses of the material in the various stages, from concentrate to high-grade nickel matte, are also presented. N ICKEL made its appearance in the Finnish mining industry forty years ago, when a nickel deposit was discovered at Petsamo in Lapland. Mond Nickel Co. received the concession for this deposit from the Finnish Government, and the Petsamon Nikkeli Company constructed a mine and a nickel smelter (1), the completion of which was prevented by the 1939 Winter War. The mine and smelter were, however, completed soon afterwards in spite of World War II,

Jan 1, 1964

By A. Glover

As the demand for natural gas as a prime global energy source continues to grow, the search for new sources of the fuel spreads into geographical areas that are more remote from the marketplace. Along with this comes the need for longer and ever more efficient pipelines. This requirement for higher value in natural gas transportation is satisfied to a large extent through the application of high strength technology and innovative design approaches that support increased design and operating pressures. This paper reviews the latest accomplishments and successes in these technologies for use in gas transmission. It also explores some of the technologies which are targeted for the future to allow the industry to achieve even higher benchmarks in reliability and cost-effectiveness. The central element in the theme of high strength technology for gas pipelines is that of high strength steel. From tensile strengths of Grade 359 a few decades ago, more and more operators are now specifying Grade 550 linepipe for their large diameter projects. As well, Grade 690 steel is operating successfully in limited transmission applications and Grade 825 has recently been installed. With the introduction of the latest high strength pipe comes the need for high strength fittings. The industry&apos;s first Grade 550 fittings were recently specified and installed on a project with Grade 825 line pipe. High strength materials can only be implemented successfully if compatible design and construction processes are in place. The latest developments in strain- and reliability based design will be described as well as the corresponding advancements in welding and inspection technology.

Jan 1, 2005

By J. Lui

At its Copper Cliff Smelter, bulk nickel and copper concentrate is processed in two Inca flash furnaces and Peirce Smith converters to produce Bessemer matte containing 0.6%Fe. After slow cooling and Matte Separation, Bessemer matte is converted into three main products using magnetic separation and flotation technology: (1) a nickel containing chalcocite concentrate (MK); (2) two types of copper containing nickel sulfide (ME and MR); (3) metallics (MYN). MK is further processed in the Inca top blowing bottom stirring MK Reactor to produce semi-blister copper containing ~4%Ni and ~3±1 %S. The semi-blister copper is then purified in the multi-purpose vessels (MPV) to produce blister copper by reducing Ni, Fe and S content through oxidation. High melting point NiO is formed inside the MPVs. The accumulation of solid NiO and other oxides requires periodic cleaning by adding reductant and furnace matte, a unique process called "washout" at Inca. For many years, the reductant used for the "washout" process has been 15%Si Ferro-silicon. With increasing cost and limited suppliers for 15%FeSi, alternative reductants were pursued. This paper summarizes the development and commercialization of new alternative reductants for MPV "washout".

Jan 1, 2007

By L. A. Nazarova, M. Vandamme, L. A. Nazarov, R. I. Rodin

"The paper describes a new method of interpreting the “canister test” data for the quantitative estimation of gas-kinetic parameters of coal bed based on the developed model of gas emission from coal sample placed in a sealed container. The model accounts for grain-size composition of the sample, initial gas content S, as well as coefficients of diffusion D and mass transfer ?. The inverse coefficient problem is formulated to find S, D and ??from the data of pressure measurements in the sealed container. It is shown that the inverse problem is uniquely solvable if the pressure is dropped during the experiment. The method has been tested using the data from an underground coal mine in the Kuznetsk Basin.Based on the poroelastic model of a coal bed and Khristianovich’s concept about origination and evolution of the filtration zone F in the neighborhood of a degassing borehole the authors considered the corresponding direct problem on rock mass geomechanical state. It was offered interpretation method for data on pressure measurements in a plugged degassing borehole allows evaluation of the diffusion coefficient, the horizontal component of natural stress field and parameters of F. The related inverse problem of the mixed type is formulated, and the cost function is constructed. The analysis using synthetic input data has shown that the cost function has a number of local minimums arranged on the same straight line, one of the minimums being the inverse problem solution. INTRODUCTIONPre-mine degassing is an integral part of coal mining. It allows mitigation of induced accidents in mines (coal and gas outbursts, rock bursts) (Guide, 1990; Malyshev & Airuni, 1999; Seidle, 2011) and also furnishes an alternative and ecology-friendly energy source—methane (Rice, 1997; Nambo, 2001). Choosing an optimized pattern of degassing boreholes, as well as estimating degassing time and amount of gas recovered requires data on gas-kinetics indices of coal beds out of which the key parameter is a gas content S. According to the latest guidelines for coal mines in Russia (Ruban et al, 2012), mining is allowed if S in a coal bed section is under 7 kg/m3."

Jan 1, 2015

By K. Morin, C. -Y. Hon, G. Lachapelle

"Air-sampling results suggest drill operators working inside environmental drilling cabs at an open-pit gold mine in Nunavut, Canada, are at risk of exposure to asbestos and silica (quartz). The authors installed RESPA® CF Vortex HyperFLOW® units, which showed promising results under laboratory conditions. The goal was to evaluate the effectiveness of these units under actual working conditions. Personal and area air sampling was conducted in drilling cabs with and without the unit and a Wilcoxon rank-sum test was performed to compare the results. Particulate concentrations were significantly lower in drill cabs with a unit installed than in those without.RÉSUMÉ Selon les résultats d’une campagne d’échantillonnage de l’air, les foreurs travaillant dans des cabines de forage environnemental dans une mine d’or à ciel ouvert du Nunavut, au Canada, risquent d’être exposés à l’amiante et la silice (sous forme de quartz). Les auteurs ont installé des unités RESPA® CF Vortex HyperFLOW®, lesquelles of frent des résultats prometteurs en laboratoire. L’objectif est d’évaluer l’efficacité de ces unités dans des conditions de travail réelles. Des échantillons de l’air inhalé par le personnel et dans les aires de travail ont été évalués dans des cabines de foreuses équipées ou non de cette unité ; un test de Wilcoxon (également appelé test de la somme des rangs de Wilcoxon) a été mené afin de comparer les résultats. Les concentrations particulaires étaient considérablement plus faibles dans les cabines de foreuses équipées d’une unité que dans celles en étant dépourvues.INTRODUCTIONGenerally, mining operations are associated with a variety of occupational hazards. In an open-pit gold mine in Nunavut, Canada, drill operators are routinely exposed to asbestos (primarily amosite) and silica (quartz)—two naturally occurring substances in the ore that is to be drilled (Table 1). Inhalation is the primary route of exposure for these two hazards, which are associated with respiratory health effects such as asbestosis and silicosis, respectively. In addition, asbestos and silica are classified as human carcinogens by the International Agency for Research in Cancer (2001, 2011). Given the toxicity of these two agents, it is imperative that precautions be taken to minimize the risk of exposure of the mine’s workforce. To address this matter, the mine has an exposure-control plan, which includes the provision of personal protective equipment, personal hygiene facilities, training, and a medical surveillance program. Furthermore, the mine performs occupational exposure assessments or air sampling on a regular basis because the morphology of the ore changes rapidly with respect to asbestos and silica content."

Jan 1, 2017

By H. Oterdoom, S. Pilger, T. P. Bui, J. Rotarius

"Most FeNi furnaces used to rely on post-combustion and off-gas cooling inside the furnace to eliminate the produced CO gas, and control the off gas temperature. As furnace load, capacity, and thus gas volumes increased over the years, this led to increased instabilities that can cause problems in controlling the operation. Some of the large capacity furnaces nowadays work with partial or full combustion outside the furnace, more similar to the steel industry. Forced combustion with or without enriched air and other additions can support in controlling post-combustion, stabilizing and even reducing off gas amounts, and affecting composition. This paper presents some of the possibilities and advantages of having a specially designed post-combustion system for the FeNi laterite industry, but that could also be applied to other processes as well.Large Scale Furnaces In the FeNi industry, the Rotary Kiln Electric Furnace (RKEF) process is still going strong in spite of continuous hope that hydrometallurgical processes will one day make the RKEF plant obsolete. Within the pyrometallurgical plants there is a continuous trend for larger scale furnaces. The development for a number of furnaces that were started before 1985 and increased capacity by “natural growth” is given in Figure 1. Natural growth refers to the development of the plants that after having mastered a certain level of operation, were ready for a higher load that could be installed either with a new furnace on the same site, or during a revamp. The advantages of natural growth are numerous, for example: •,Deep knowledge of the ore and its’ behavior, no need for testing, and little risk of surprises. •,Mining, laboratory, equipment, etc. is all proven technology for the conditions on site. •,Starting a furnace with increased capacity is a re-start, not a green-field commissioning. •,Typically, when increasing the production capacity of an existing plant, not the entire plant is commissioned for the first time, but only a part. In the FeNi laterite industry for example, the kilns may already have had the capacity to provide enough material."

Jan 1, 2017

By A. -M. Lafront

The corrosion resistance of die-cast and freely-solidified and electromagnetically-stirred thixocast AZ91D alloy has been studied using electrochemical noise technique in a 0.05M NaCI solution at pH 6.1 and 25°C. Specimens polished at different depths were immersed for a period of 75 min in order to assess the influence of the microstructure on corrosion kinetics and morphology. At depths between 10 and 50 µm (skin), all specimens showed general non-uniform corrosion with the lowest corrosion resistance. Between 100 and 200 µmn (interior skin), the observed corrosion was accompanied by superficial undefined pits due to metastable pitting. The corrosion form for 100-200 µm gave the best corrosion resistance. Stable pitting corrosion was observed beyond 400 µm deep on the bulk specimens. The skin of all thixocast specimens prepared billets showed a more corroded surface than that of die-cast. The interior skin as well as the bulk specimens showed better performance than that of the die-cast specimens.

Jan 1, 2007

By F. Rashchi, N. Naseri Joda

Recycling of electronic wastes is an important subject both from an environmental point of view and also the recovery of valuable materials. In this research, PC board scraps were leached to recover Cu, Ag, Au and Pd. Due to the high cost of the shredding process and to avoid secondary pollution from odors and dusts, board scraps were cut into 5X5 cm2 pieces. To determine the most effective leachant, aqua regia, nitric acid, hydrochloric acid, ammonium persulfate and potassium persulfate were tested. The effect of the leaching parameters, the leachant concentration, temperature, leaching time and liquid to solid ratio were studied and optimized using response surface methodology.

Jan 1, 2011

By Andrew Dobson, Cheryl Allen, Enrique Acuña

"Totten Mine return air raise was designed with two parallel fans equipped with silencers to reduce the noise emitted from the outlets into the environment. As development and production of the mine progressed through the past years, the silencer system needed to be upgraded, and additional maintenance strategies have been necessary to meet the regulatory noise limits enforced by the province of Ontario. The current mine plan will require the fans to reach the upper limit of their capacity by Q1 2019. To achieve this operational target, additional silencing capability has been required and Totten Mine has explored alternatives to further extend the noise silencing capacity available considering the current constraints at the mine site. The alternatives included a new silencer baffle design and a new layout that have allowed doubling the length of the silencer system. Using acoustic measurement data collected on several occasions, this paper presents and discusses the performance of the various silencing systems which have been installed on the return air fans at Totten Mine.INTRODUCTION Vale Canada Limited’s Totten Mine is a base metal, underground mine extracting nickel and copper, situated in the Sudbury Basin of Ontario. The mine initiated operations at the end of 2013, and is equipped with two main return air fans and two main fresh air fans located on surface. Both fresh air and return air fans are set in a parallel arrangement to operate as integrated units and are equipped with variable frequency drives (VFDs) to allow for the remote modification of their operating set point, usually between 600 to 880 rpm, depending on the mine’s requirements. The main return air raise (RAR) fans are also equipped with dissipative baffle silencers to attenuate the noise emitted to the environment. Approximately four years ago, acoustical measurements conducted to verify compliance with the applicable regulatory criteria, and respond to noise concerns from neighboring residents, concluded that the sound emissions of the main return air raise exceeded the noise design parameters. The acoustic tones of the fans were audible offsite, at a residential location, approximately 9 km northeast of the mine site. The elevated sound levels and offsite audibility was due to degradation of the original discharge silencers from moisture and particulate being drawn from underground workings and passing through the silencer baffles. The audibility was also due to an outlet directivity pattern which directed noise towards the residential location."

Jan 1, 2019

By A. F. Matheson

The St. John Del Rey Mining Company, Limited, is an English company owning 150 square miles -of mining lands near Belo Horizonte, Minas Geraes, Brazil. The area is 2,300 to 5,000 feet above sea level, with a pleasant and healthy climate. Bedrock is Precambrian. The Nova Lima series of metamorphosed sediments and some volcanics is overlain uncomfortably by the Minas series of quartzites, itabirites. etc. Batholithic granite and gneiss cut both series and basic dykes cut all these rocks. There are important deposits of gold, iron, and manganese on the Company&apos;s holdings, as well as occurrences of arsenic, antimony, cobalt, nickel, dolomite, day, quartz, -ochre, bauxite, kyanite, and asbestos. Except for gold and consequent recovery of arsenic, all the other materials are relatively unexploited. The Company operates the Morro Velho gold mine and the Espirito Santo and Raposos gold mine. The Morro Velho mine was purchased in 1834 for £56,000. To the end of 1952 it had produced 7,000,000 troy ounces of gold from 15,000,000 short tons of ore. The ore z?ones are replacement deposits in a sinuous siliceous dolomitic rock locally termed "lapa seca," and plunge east, near surface at 45 °, at 8,000 feet at 15°. The ore minerals are pyrrhotite, arsenopyrite, pyrite, and chalcopyrite. Gold is finely distributed and almost nowhere visible. Ore reserves at the end of 1952 were estimated at 5.5 million short tons grading 0.39 oz. gold per ton. Chances exist for new ore within the mine area. The Espirito Santo and Reposos mine, in folded banded iron formation, has mineralization similar to Morro Velho but sulphides are less abundant. The mine to a depth of 2,500 feet has estimated ore reserves of 1.5 million tons of an average grade of 0.28 oz. gold per ton. New ore may be expected both laterally and at depth. To the end -of 1952, the ?Company had paid dividends of almost £4,- 600,000, largely earned from the operation of the gold mines.

Jan 1, 1956

By Matej Petružálek, Václav Vavrycuk, Tomáš Svitek, Tomáš Lokajícek

The most common type of waves used for probing anisotropy of rocks in laboratory is the direct P wave. Information potential of the measured P-wave velocity, however, is limited. In rocks displaying weak triclinic anisotropy, the P-wave velocity depends just on 15 linear combinations of 21 elastic parameters, called the weak-anisotropy parameters. In strong triclinic anisotropy, the P-wave velocity depends on the whole set of 21 elastic parameters, but inversion for 6 of them is ill-conditioned and these parameters are retrieved with a low accuracy. Therefore, in order to retrieve the complete elastic tensor accurately, velocities of S waves must also be measured and inverted. For this purpose, we developed a lab facility which allows the P- and S-wave ultrasonic sounding of spherical rock samples in 132 directions distributes regularly over the sphere. The velocities are measured using a pair of P-wave sensors with the transmitter and receiver polarized along the radial direction and using two pairs of S-wave sensors with the transmitter and receiver polarized tangentially to the spherical sample in mutually perpendicular directions. We present an inversion method for elastic parameters describing general triclinic anisotropy. We demonstrate on synthetic tests that the inversion becomes more robust and stable if the S-wave velocities are included. This applies even to the case when the velocity of the S waves is measured in a limited number of directions and with a significantly lower accuracy than that of the P wave. Finally, we analyze velocities measured on a rock sample from the Outokumpu deep drill hole, Finland, including the error analysis for several levels of confining pressure.

Jan 1, 2015

By Paul F. Grundy

The ever changing conditions in the coal-mining industry and the increasing competition of other fuels such as oil, natural gas, wood refuse, etc., have made it imperative that the coal operator be in a position to supply a constantly uniform and clean product. The old idea of putting on the market "anything so long as it&apos;s black" no longer holds good. Today&apos;s users of fuel have to consider the amount of heat per dollar they obtain from the fuel they buy. Burning of coal has become largely mechanical, at least so far as industrial coal is concerned, and industrial coal is the kind the bituminous operator is for the most part called upon to supply. When we get into things mechanical, the matter of precision has a mighty bearing on efficiency. Precision in coal means standardization of quality, or uniformity of preparation in size and also in ash and moisture content. The trend of coal mining is ever towards more and more mechanization. Mechanization means coal-cutting machinery, loading machinery, conveying machinery, etc. Although such methods cut the cost, the cleanliness of coal so mined and loaded is not controllable to the same extent as when each operation is by hand labour. The operator has therefore the problem of mining his coal as cheaply as possible, but at the same time preparing a product which will to the utmost satisfy his customer. The answer is a mechanical cleaning plant. Before installing a cleaning plant, however, the operator must take into consideration the cleansability of the coal from his particular mine. This is accomplished by taking representative samples of the seam or seams to be treated, and subjecting these to screen tests, followed by float and sink tests on each size product. From these tests, it can be readily found to what degree of cleanliness the several sizes can be prepared advantageously, and also what will be the percentage recovery of cleaned coal. The accompanying tables give the results of representative tests on Michel coals of minus-2-inch size. All coal over 2-inc.h was intended to be hand cleaned. The coal-cleaning plants in general use at the present time come under two broad classifications, namely, wet and dry.

Jan 1, 1934