Search Documents

By C Hertle

GHD-Black & Veatch (GHD-BV) have completed design and specification of the ash thickening plant at Tarong Power Station, including operation of a pilot plant. Construction of the plant is in progress and commissioning is planned for early-2004. The objective of the new plant is to convert the low concentration (lean phase) ash slurry currently generated by the power station into concentrated slurry which will then be pumped to the existing ash dam. Water recovered from the lean slurry will be returned to the power station for reuse. The drivers behind this project are to extend the life of the ash dam and to reduce water pumping costs. A maximum flow of 1000 litres per second is expected in the thickening plant. The process involves a screening phase, which removes large material that could cause blockages or equipment damage. A 50 metre diameter thickener then concentrates the screened lean ash slurry to 55 - 60 per cent w/w solids. In addition, the thickener plant will allow the harvesting of floating cenospheres (hollow, spherical ash particles) from the lean slurry. Cenospheres are currently collected from the surface of the ash dam and drained on a pad adjacent to the dam. The new system will use a surface skimmer to remove the cenospheres from the thickener and transfer them to settling ponds for further classification. The settling ponds simulate the detention on the existing ash dam, and allow entrained fine ash and slow settling cenospheres time to settle. As settling occurs in ponds, the slow settling cenospheres can be completely recovered whereas when they settle in the dam, the opportunity for recovery is lost. Cenospheres are a valuable by-product produced during the combustion process, and recycling of this material reduces the waste generated by the power station. Water recovered from the thickener drains to a three megalitre reservoir. Water is drawn from the reservoir for thickener plant service water and various other uses in the power station. The bulk of the water is used to sluice ash from the power station to the thickening plant. In the current configuration, surface water from the ash dam is reused but must be pumped several kilometres back up to the power station. The dam also holds an inventory of several thousand megalitres of water and has significant evaporative losses. Therefore the current raw water make up demand is substantial. In addition, some areas of the power station traditionally using raw water will be modified as part of this project to allow the use of recovered water, further reducing the raw water demand. The design incorporates many features of sustainable water management. By more effectively recovering water from the lean ash slurry, the amount of raw water make up required by the system will be significantly reduced. This method of water recovery provides a more sustainable and energy efficient ash-transport mechanism.

Jan 1, 2003

By J P. R de Villiers

The Vanderbijl Park sinter plant in South Africa was investigated to determine the reason for the production of very fine sinter not acceptable as feedstock for the blast furnace. A procedure was designed to generate representative samples and to prepare the samples for chemical and mineralogical analyses. Results from a mineral analyser showed that the samples are extremely heterogeneous and therefore the sampling and sample preparation methods had to be tested in order to produce representative samples. The high production capacity at the sinter plant could also give rise to sampling errors. The method designed involved sampling of the conveyor belt at the sinter plant every four hours for the duration of three days. The samples were then milled and split into smaller sections appropriate for analysis. X-Ray diffraction (XRD) and X-Ray fluorescence (XRF) analyses were conducted on the samples. The results showed a standard deviation of less then one per cent, which indicates that the samples were representative and that the method used was therefore adequate. Systematic differences in the phase proportions between normal and fine sinter samples were detected, with the fine sinter containing more haematite than the normal sinter. The sampling method employed gives added confidence that the differences are real.

Jan 1, 2008

By P McGavin, R von Varendorff

With the economic trend towards reduced capital spend, more stakeholders are focusing on improved operational efficiency and productivity. Advancements in achieving the optimum dollar-per-tonnage will be more dependent on creating a logistics system that is well balanced and economically optimised. Critical to predicting a successful business case is the ability to accurately define capacity, realistically increase throughput and proactively translate objectives into design and operating requirements. Failure to do this will create an unrealistic perception of capacity and performance for the export corridor. This transition requires a fundamental understanding of the drivers that impact capacity, cost and value across the entire logistics chain. Through examples, this paper will identify the contextual requirements for simulation models that assist decision-makers and stakeholders to more clearly understand the implications of decisions that will define capacity and operational performance. The aim of this approach is to provide a rigorous analysis of the outcomes - regardless of whether the export corridor is owned, used and operated by one entity or various companies.CITATION:von Varendorff, R and McGavin, P, 2013. Can we live up to the capacity expectations weÆre predicting for our iron ore export corridors?, in Proceedings Iron Ore 2013 , pp 553-560 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By S Sabanov

Supplementary sampling of particulate mass concentration, the number concentration and the average particle diameter of nanoparticles using a TSI Dust-Trak DRX Aerosol Monitor, Naneos Partector 2 has been conducted. The aim of this study was to evaluate suitability of the instrument for long-term monitoring of diesel particulate matter (DPM) at conditions of polymetallic mines. Sampling was conducted in an area of the active ore heading, requiring the use of a diesel-powered face haul-age loader R1700 and a mine truck Caterpillar AD-45. The sampling was done for 126 minutes at a distance of 30 metres from the mine face. Results of this field work can be used to expand the sampling program to other mines. Expected outcomes of this study are to develop costeffective DPM control strategies, improve mine ventilation, and protect mineworkers’ health.

Oct 12, 2022

By J Brown, C Roberts

The scope of this paper is to recount the development of segmental linings used in tunnel construction, starting with its inception as an improvement to the brick-lined tunnel approach of Brunel in England and moving through the history and development to the present day, before finishing with a few insights into what the future might hold. The paper also discusses the motivation for the relatively recent move towards replacing conventional steel reinforcing cages with steel fibres and the reasons why steel fibre reinforced concrete (SFRC) is rapidly becoming the material of choice for manufacturing precast concrete segmental linings.

Jan 1, 2008

The process of resource estimation of large precious metal deposits is illustrated by reference to major deposits now being mined or developed by Placer.The estimation procedure commences with building an appropriate model of the mineralization and proceeds through steps of data validation and geostatistical studies. It is important that the geologists most familiar with a deposit be involved with all stages of the estimate, and also prepare a manual estimate used to validate the kriged resource.Resource estimates are major exercises taking many man-months of work. The most time consuming part of this is usually construction of an appropriate three dimensional geological model. The data base for the resource calculations must be complete and checked for accuracy. The most appropriate estimation method must be selected.

Jan 1, 1990

By B S. S Rao, S Chandra

IndiaÆs iron ore mining industry is growing rapidly in order to augment the capacity to meet the unprecedented demand for the iron ore. Traditionally, much of Indian iron ore production came from exploitation of high-grade haematite ores, with the exception of Kudremukh which beneficiates lean grade Banded Magnetite Quartz ore. Now with the changed scenario of demand and supply, keeping long term sustainability in mind, it is imperative to develop suitable processing technology for exploitation of banded haematite quartz (BHQ) ore available abundantly and not utilised so far. In this direction detailed characterisation and beneficiation studies were conducted with BHQ iron ore from the Bellary-Hospet region of India, assaying 36.5 per cent Fe. The mineralogical studies with the image analyser system revealed the presence of maghemite and haematite as iron-bearing minerals. The gangue mineral associations were siliceous, ferro-magnesian and carbonate minerals. Higher degrees of liberation were observed in the size range of 75 - 212 microns. Liberation grind tests were performed by grinding the ore to different top sizes in a closed circuit laboratory ball mill with the ground samples subjected to Davis tube tests. The yield, grade and recovery were used as parameters to plan a two-stage wet drum magnetic separation based on grinding the primary magnetic concentrate. After subjecting the final magnetic concentrate to flotation to remove residual silica a concentrate assaying more than 68 per cent was obtained. The non-magnetic product from the primary magnetic separation was deslimed, ground, blended with secondary magnetic tails and was subjected to a two pass wet high intensity magnetic separation (WHIMS). The WHIMS concentrate was further subjected to two-stage flotation to remove residual silica to obtain concentrates assaying 64 - 66 per cent Fe. The final combined concentrate from wet drum magnet and WHIMS after flotation could yield a blast furnace (BF) grade pellet feed concentrate assaying more than 65 per cent Fe with a yield about 39 per cent and iron recovery about 70 per cent. A direct reduction (DR) grade pellet feed concentrate assaying 67 per cent Fe with a yield of about 28 - 31 per cent and iron recovery about 53 - 57 per cent could also be produced. Based on the test work, a process flow sheet was developed to beneficiate the BHQ ore for production of BF/DR grade pellet feed concentrate. In this paper methodology adopted for selection of individual process, various diagnostic tests performed to rule out other beneficiation processes and the final process flow sheet development is presented and discussed in detail.

Jan 1, 2007

Water is important commodity in the mining industry. Water is used in the many stages of mining from the exploration stages and drilling, to mine development and operation and finally throughout mine rehabilitation and post mine activities. With the use of water throughout the life span of a mine, its management is an important component in the operation of any mine. Unfortunately the use of water within the operations can be one of the major sources of pollution generated from a mine. Such contamination can occur via numerous mechanisms including ground water flow, over land flow and accidents. Contamination may occur in any stage of mining operations, for example a leaking or failed tailings dam. With the above in mind, the paper presented will focus upon the use and management of water in the mining industry: ownership rights of water û common law as well as legislative rights; a review and analysis of the existing Queensland legislation and its mechanisms for the protection of water pollution from mining operations; and conclusions drawn from the paper relating to the Queensland legislation.

Jan 1, 2003

By K S. Smith, B P. Jackson, P J. Lamothe

The upper Arkansas River south of Leadville, Colorado, USA, contains deposits of fluvial tailings from historical mining operations in the Leadville area. These deposits are possible non-point sources of acid and metal contamination to surface- and ground-water systems. We used stable-metal isotopes to help ascertain metal retention and release mechanisms that influence metal transport from the deposits to shallow ground-water systems. To accomplish this, we excavated an intact core from a small fluvial tailings deposit and performed laboratory column experiments to examine the amount of metals leaching through the core. Deionised water was continuously applied to the top of the core, and effluent was collected from the bottom of the core for a period of about two months. Three saturation conditions were used, including unsaturated, partially saturated, and fully saturated. Reducing conditions developed upon partial and complete saturation of the core. During the unsaturated leaching phase, core effluents were acidic (pH 2.8 - 3.5) and contained elevated metal concentrations. During a portion of the unsaturated leaching phase, stable-metal isotope spikes and conservative tracers were simultaneously applied to the top of the core. The isotopes provide a means to delineate metal behaviour within the core. During the unsaturated leaching phase, the isotope spikes did not exhibit breakthrough with simultaneously added conservative tracers. However, some of the stable-metal isotope spikes did break through when reducing conditions occurred in the core (during the partial- and completesaturation conditions). In this paper, we use Cd as an example of the utility of stable-metal isotopes in geochemical studies. In the case of Cd, after the core was partially saturated, the 111Cd spike was released as evidenced by a change in the Cd isotope ratios in the effluent. This release continued during the fully saturated leaching phase, however, the total Cd concentration did not increase. These results suggest that the 111Cd spike was retained inside the core during the unsaturated leaching phase, and only partially released as reducing conditions developed. Results from this core-leaching experiment indicate there is a large reservoir of water-soluble material within the fluvial tailings deposit, which yields elevated metal concentrations and high acidity, and which may degrade adjacent ground- and surface-water quality. Use of stable metal isotopes in this study facilitated the determination of different metal-retention processes, metal-release processes, and metal sources in the fluvial tailings deposit in response to changing geochemical conditions.

Jan 1, 2003

By L Grigorov, G J. Jame, A V. Nguyen

The dewetting kinetics between a small air-liquid interface and a silica (negatively charged in water) planar surface in solutions of dodecylammonium chloride (cationic surfactant) has been investigated using the Scheludko cell and digital high-speed video microscopy. The gas-liquid interface was created at the bottom of a small silica capillary of the cell and then was moved towards the silica planar surface. After the rupture of the liquid films between the interfaces, the expansion of the gas-liquid-solid three-phase contact (TPC) line was observed and recorded using a digital high-speed video microscope system, operating at 1000 frames per second. The surface tension of the surfactant solution was measured using the pendant drop technique. The equilibrium contact angle was measured using the Scheludko-Minings method with a silica micro-sphere. The TPC radius was determined as a function of time and compared against the available hydrodynamic and molecular-kinetic models. The experimental data are described very well by the molecular-kinetic model for the TPC line motion. The hydrodynamic model is in agreement with the experimental data only for a short time after inception of the three-phase contact expansion.

Jan 1, 2005

By B B. Beamish, M S. Kizil

The processes that take place during the development of a heating are difficult to visualise. Bulk coal self-heating tests at The University of Queensland (UQ) using a two-metre column are providing graphic evidence of the stages that occur during a heating. Data obtained from these tests, both temperature and corresponding off-gas evolution can be transformed into what is effectively a video-replay of the heating event. This is achieved by loading both sets of data into a newly developed animation package called Hotspot. The resulting animation is ideal for spontaneous combustion training purposes as the viewer can readily identify the different hot spot stages and corresponding off-gas signatures. Colour coding of the coal temperature, as the hot spot forms, highlights its location in the coal pile and shows its ability to migrate upwind. An added benefit of the package is that once a mine has been tested in the UQ two-metre column, there is a permanent record of that particular coals performance for mine personnel to view.

Jan 1, 2005

Precipitation of inorganic compounds or metals from aqueous solutions can either be physical (crystallisation) or chemical in nature. Chemical processes are varied; they may be due to hydrolytic action, due to ionic interaction, or due to reduction (ie transfer of electrons). Transfer of electrons in reduction processes may take place homogeneously or heterogeneously. In the first case it may be ionic or nonionic in nature. Heterogeneous processes may be electrochemical or electrolytic. Examples of interest to hydrometallurgy are given.

Jan 1, 1993

In order to do the discharge estimation better, it is valuable to find out appropriate formulas for estimating discharge in various pits, based on accumulating data, summarizing discharge patterns applying optimum seeking method and principle, by seeking redical exponent with help of the method of exhaustion, as well as testing and making statistics, in accordance with the quality standards established by our practical experience.

Jan 1, 1988

The first stage in the refining of lead blast furnace bullion is the removal of copper and is normally done as a batch process in open kettles.A number of attempts have been made to establish continuous processes operating in reverberatory type furnaces, but the growth of accretions in the furnace has always presented a serious problem.The Broken Hill Associated Smelters Pty. Ltd. (RH.A.S.) at Port Pirie have overcome this problem by constructing a reverberatory furnace and ancillary cooling system of a novel design.Although a number of mechanical and metallurgical problems still remain to be solved, it is claimed that a workable continuous copper drossing process has been established.INTRODUCTIONLead bullion emerging from the blast furnaces at Port Pirie is at a temperature of about 1100°C and contains, among other impurities, about 1 per cent of copper.The first stage of refining is the removal of this copper by a drossing operation and in the past this was done, batchwise, by allowing the bullion to cool back in 100 ton kettles.At about 700°C, copper dross begins to separate as a crust on the surface of the kettle and this separation was allowed to continue down to about 450°C when the crust was brokenup and skimmed manually using a long handled, balanced, spoon. The dross was then smelted in a reverberatory furnace to produce a saleable copper matte and separate out lead bullion, which was returned to the drossing kettles. The copper content of the drossed bullion was then further reduced by a sulphur treatment process.The drossing operations involved hard manual labour under arduous conditions and the pouring of hot bullion into...

Jan 1, 1963

By M Zhu, G Tranell, J You, K Tang, X Ma

The thermal conductivity of slag is critical for the efficiency of high temperature metallurgical processes such as the smelting reduction of ferroalloys, the ladle refining and the continuous casting mold flux in steelmaking. Experimental determination of slag’s thermal conductivity is fraught with challenges, as seen in yielding data for the SiO2-Al2O3-CaO system that are often inconsistent and widely dispersed. In molten slags of this system, thermal transport occurs via phonons within the network structure. To quantitatively describe thermal conductivity based on the microstructure, hightemperature Raman spectroscopy was employed to measure the silicate tetrahedra Qi (i = 0, 1, 2, 3), with Q4 species inferred from mass balance. This study also integrated molecular dynamics simulations to provide a fundamental understanding of the microstructure units distributions. Machine learning algorithms, especially deep neural networks, were applied to establish the relationship between slag composition and the configuration of tetrahedra. The thermal conductivities were then connected with silicate tetrahedra Qi using an Arrhenius-type formalism. This study sets the stage for extending our findings to more complex, multicomponent slags, enhancing their practical application in industrial processes.

Aug 21, 2024

In the consideration of coal resources in this country one of the most neglected aspects and perhaps one of the most important is that of the geologic controls on coal formation. The composition, properties, thickness and distribution of the coal are all determined by geological factors. The extent and amounts of coal to be found in the South Auckland area have great economic significance, and are in the main considered here. Upheaval of the New Zealand geosyncline during the Rangitata Orogeny produced a system of parallel, north-south trending basement ridges and basins in the South Auckland area. A subtropical climate and relative tectonic stability allowed deep weathering of these mesozoic greywackes in the late Cretaceous and early Tertiary. Such weathering, markedly reduced the landscape relief, and provided vast supplied of very fine detritus for later sedimentation as the Waikato Coal Measures. This coal measure phase marked the beginnings of Tertiary  sedimentation in this region and represented a change from a sub-aerial weathering regime to a fresh water swamp environment.

Jan 1, 1976

By G Solly, P J. Leevers

Day-to-day operating practices at existing operations need provide high quality data for decisions that will impact directly on the potential value of the available resource, in addition to meeting standards of quality expected of data used in feasibility studies that will be completed to obtain additional capital required to finance operational improvements. Drill hole location, down hole survey and assay data standards of accuracy and precision have received considerable attention in recent years. The authors propose that geological descriptions of both cored and non-cored drilling warrant at least equal attention, considering their fundamental role in establishing the framework used for geological modeling and resource estimation. The iron ore deposits of the Middleback Ranges have been a major source of iron ore for almost a century. High-grade hematite-dominant ore is currently mined by OneSteel from three open pit operations supplying ore to the companyÆs integrated steelworks at Whyalla. A review of OneSteelÆs future iron ore resources, commenced in 2002, highlighted the need for more flexible and comprehensive management of all forms of geological data used in resource evaluation. Driving this program was the information needs of feasibility studies of the Iron Magnet deposit, located beneath the existing Iron Duke and Iron Duchess mines. Prior to the beginning of 2003, resource evaluation drilling data collected by OneSteel was managed using an in-house system based on industry standard relational database software. The system was demonstrably effective in ensuring the fundamental integrity of basic drilling data, but lacked necessary capabilities for the acquisition and management of geological descriptions, geotechnical and geophysical data obtained by down-hole logging. OneSteelÆs existing system for the management and interpretation of geological descriptions was restricted to storage of a single three digit code for each lithological description interval. The original logs for a large number of older drill holes could not be located, having been either poorly archived or culled from the database in the belief that they did not contribute to the understanding of the resources currently being mined. The three digit codes represented a combination of lithological and stratigraphic descriptions, including many subtle variations in iron ore colour and texture believed to be associated with variations in geochemistry, but subsequently demonstrated to be either incorrect or inconsistently applied. This resulted in the establishment of a plethora of codes for a relatively small number of distinct lithologies. Improvements implemented by OneSteel geologists addressed these shortcomings by ensuring the new data management system: facilitated the objective description of lithological characteristics; distinguished between obsevations and interpretations (eg lithology versus stratigraphy); promoted consistency between descriptions provided by different geologists; and helped to ensure data integrity by developing an audit trail for alterations made to data subsequent to its acquisition. The data used to develop interpretations of mineralisation distribution and characteristics are fundamental to the effective utilisation of a mineral resource: any mineÆs most important asset. Resource related risk is widely recognised as the principal source of technical risks affecting resource development projects, whether they are new mines or expansions of existing operations. A key lesson from this work is that most commercial or æin-houseÆ developed geological data management systems are able to handle basic data validation tasks effectively. Geologists, however, need to ensure that the data management system is appropriately structured to help promote the acquisition of objective and consistent data for interpretation.

Jan 1, 2003

Peko Mines N.L. has considerable experience in the treatment of a wide range of comparatively small orebodies.Gold-silver, bismuth, and sulphide and oxide copper ores are treated under difficult geographical conditions.Treatment of these ores is complicated by some unusual metallurgical factors.Metallurgical operations are described, including the treatment of the gold-bismuth-copper ore from Juno. The new Warrego mine is to have a highly instrumented concentrator by December 1971. Autogenous grinding is being considered.

Jan 1, 1969

The long continuing controversy over the Origin of fusain, whether it is a product of primeval forest fires, or of special conditions of weathering (including bacterial decay) of the vegetal debris concerned prior to, burial, has now been extended, to include the possibility that fusain is a product of the coalifaction process subsequent to deposition, so that doubt may reach even to its time of formation.The conflicting views on this point are summarised in the following quotations from two recent publications (my italics in each quotation):1. "Recent observations made in peat and brown coal deposits in Australia, England and Germany strongly suggest that practically all fusain is formed by coalifaction after deposition and 'preliminary compression. In deposits of advanced brown coal rank, it normally takes the shape of pieces of wood compressed parallel to the bedding plane; and some fragments consisting partly of fusain and partly of vitrain exhibit the same amount of compression throughout. This would seem to indicate fusinisation after burial, as hard brittle charcoal would be crushed, or else retain its original irregular shape if strong enough to withstand pressure.In some immature deposits, however, where cover is of a hydrostatic nature rather than a vertical compressionar force, occasional pieces of fusinised wood showing very little flattening are present, but such immature deposits seldom contain the proportion of fusain found in higher rank coals. In view of this, and the possibility of introduction of charcoal into peat deposits, it is felt that a small amount of the fusain in coal may represent wood charred before burial, but most of it almost certaInly originated as a product of fusinisation after burial" (Dulhunty, 1948, p.14).

Jan 1, 1953

The current drill-and-blast method of tunnelling is cyclic and, for this reason above all others, has a future application potential which is lower than that of continuous methods. There is scope for progress in several facets of today's drill-and-blast tunnelling. But even if each of its unit operations and the synthesis of these were to be optimised, this conventional method will, in the long term, fail to be a serious competitor for tunnelboring machines (TBMs), roadheaders and the like. If its role in tunnelling is not to decline at an increasing rate, drill-and-blast will need to be transformed into a continuous system. Boring and cutting machines consume considerable energy (and expenditure) in creating rock fragments which are smaller than those required by muck-handling equipment. In this respect, blasting is more efficient. Mechanical methods are also less versatile and flexible and, when planning proceeds on a basis of meagre or inadequate geological data, cannot be costed as accurately. Currently, research gains for TBMs and roadheaders are greater than those for conventional tunnelling. If (as is likely) the disadvantages of mechanical methods continue to be reduced at a greater rate, the swing away from drilling and blasting will gain momentum.

Jan 1, 1987