Search Documents

By D Reid

Many of the relevant engineering behaviours of tailings are controlled to a large degree by the density of the material. For example, loose tailings are prone to brittle strength loss, while dense tailings are dilative (i.e. gain strength) at large shear strains. The critical state framework has been successfully developed over the past few decades to assess whether in situ conditions are contractive or dilative, and estimate relevant engineering parameters on that basis. Tailings comprising primarily silt-sized particles, when subaqueously deposited, often form a particularly loose state compared to subaerially deposited material of similar index properties. Such subaqueous deposition occurs in the decant pond area, where the tailings typically pluviate in quiescent conditions within a pond of standing water. Silt tailings deposited in such a manner have been observed to be extremely loose in a number of TSF investigations. Of particular concern, the deposited material in such cases appear to be significantly looser than can be reproduced in the laboratory - even using moist tamping, the sample preparation method which can usually produce the loosest samples possible in laboratory conditions. While the loose density of subaqueously deposited silt tailings is clear, in a well-managed upstream-raised TSF the decant pond is usually small and far from the perimeter embankments, however there are a number of examples where the engineering performance of such materials becomes relevant – for example, when historical deposition practices were poor, resulting in subaqueous deposition near the perimeter embankment. This paper outlines the geotechnical characterisation of a number of such subaqueously-deposited zones, compares the in situ state to that achievable in the laboratory, and discusses options for assessing the expected engineering performance of such materials when comparable laboratory tests are unavailable.

Jul 1, 2021

By M M. Tarshan

Separator performance is evaluated by the so-called separation efficiency. The concept of efficiency in mineral dressing operations must be interpreted with considerable care. Although qualitative use of term efficiency is valid and useful, difficulties arise in expressing it quantitatively because two conflicting criteria, grade and recovery are normally involved in its evaluation. It is undesirable to express efficiency as a single value, even though this is frequently done in practice, since there are strictly speaking an infinite number of combinations of grade and recovery that can give that one value. Inefficiencies in processes can be attributed to three broad sources: mineral limitations as represented by the separability curves, equipment limitations (which prevent the maximum separation indicated by the separability curves), and human failure to minimise these inefficiencies. In the present paper, the efficiency of a two-constituent separation process has been examined. The separation process has been evaluated by comparing the sharpness factor of the actual, the absolutely efficient and the absolutely inefficient operations.

Jan 1, 2000

By Lloyd F, Arnold D. A, Hagan T. O

This paper investigates the problems that are encountered in mining at extreme depths. It looks into the rock mechanic aspects, especially the high stress levels that will occur, and the hazard of rockbursts. Furthermore, environmental problems are discussed, with refrigeration and reduction of neat loads being major methods of maintaining ,sorkable conditions. The paper concludes that it will be of tmost importance to have a planning team of Tne highest quality to ensure that conditions are maintained so that work can be carried out safely and under reasonable conditions.

Jan 1, 1986

By Warren R. P

When the original Mount Gunson joint venture, between CSR and United Uranium ceased operations in December 1971, an intensive ex- ploration campaign was launched to prospect for more ore in the Mount Gunson region. This campaign resulted in the discovery of the Cattle Grid deposit. A comprehensive sampling programme proved the existence of 4.6 million tonnes of ore, at a mean grade of 2.4% Cu, calculated at a 1.0% Cu cut-off. The planning and development programme that followed this discovery included not only the mining and metallurgical aspects of the exploration of the deposit, but also the en- vironmental aspects. Preliminary work included data collection with respect to meteorology, soil types, and existing flora and fauna.

Jan 1, 1976

Australia has a high level of research and development capabilities in government, industry and tertiary institutions. In the- remote sensing fields, we have developed a range of applications in geology, agriculture, infrastructure and environmental monitoring which are very cost effective and applicable to projects in the Asian and Pacific region. Support by the Department of Science through the Scientific Industries Steering Committee has enabled rapid penetration of this technological capability into projects with significant economic and financial benefits. It has also led to the opportunity for development of new sensors and processing systems, through collaborative projects with regional countries, which. will have applications in cloud covered, rainforest, and coastal tropical regions for geological and resource applications.

Jan 1, 1987

By Reynolds JO

This contribution by. The Australasian Institute of Mining and Metallurgy has three main thrusts. First, an Institute (and industry) view on academia and the need for more entrepreneurship at top academic levels, second the need to lift our technological game, and third, professionalism and the perceived role of mineral industry education. While I will deal with each of these separately they are of course inter- related and can be brought together under the frequently used, but insufficiently practised title, "communications". First then, The Institute and industry view of academia. There are some academics in the audience and I imagine they may wish to reply to my remarks with an academic view of industry. That is not unreasonable. Like all human institutions, academic institutions vary in quality and characteristics. Some are successful and some less so. Some historically are well renowned. Others that were once successful schools have declined. Lesser known schools have grown into prominence. What is it that sets apart 'good' highly regarded schools from those that are not so well regarded? It comes down to one main ingredient - "leadership". The strong mining schools in the past 100 years have been strong because they have had outstanding and clearly identified leaders. Strong clearly identified leadership has always had rapport with, and the support of the industry. The two go hand- in-hand, each nourishing and supporting the Other.

Jan 1, 1986

By A Jakowetz

OxianaÆs Sepon Copper Operation (part of the combined Sepon Gold and Copper Operation) is located in Savannaket Province, in southern central Lao PDR. The site is relatively remote, being some five hours inland from the Laos/Thailand border crossing on the Mekong River. The copper processing plant was designed to treat 1.3 Mtpa ROM ore to produce 60 000 tpa of copper cathode. Commissioning of the processing plant was completed in mid March 2005 with ramp up completed in January 2006 with 5260 tonnes of cathode harvested in this month. The focus of this paper is on SeponÆs unique grinding circuit. The entire grinding circuit is operated at highly acidic conditions, adding a number of different operational issues over and above those normally associated with grinding circuits. It became evident early in the ramp up, that reaching design mill throughput of 170 dry tonnes per hour with the original design would be challenging, coupled with the realisation that ceramic grinding media consumption had been underestimated. In order to lift the overall throughput of the processing plant, a significant continuous improvement process has been implemented within the grinding circuit to lift this key unitÆs production capacity. This presentation will focus on the key areas that have been addressed in the 12 month ramp up period and highlight areas for future work. Results to date have shown this improvement process to be very successful, with throughput rates in excess of 200 tph regularly achieved.

Jan 1, 2006

By J Naude

The TauTona (Sotho for Great Lion) Mine near Carletonville, which is one of AngloGold AshantiÆs most profitable operations in South Africa, has started a multi-million dollar expansion project that is expected to extend the operational life of the mine by at least three years. The project will also secure some 1900 jobs for existing workers and contract workers. The $US140 million project entails the development of the orebody to a record depth of almost 4 km underground. It means that TauTona, which already mines gold at the deepest levels in the world, will deepen its mining activities from 3600 m to a new record depth of 3910 m. There is great anticipation about the expansion program, especially because of new technology that will contribute to a safer working environment. It includes a simplified hoisting system that will minimise safety risks in conveyance activities. Due to the unique nature of this project, depth below surface and working through a three-tier shaft system, various innovative measures were incorporated into the planning of the endeavour. Special support equipment was designed to reduce cycle times and enable the crews to install the extensive support, prescribed by the mineÆs rock engineering department, right up to the face before every blast. Both declines dip at 23¦. The personnel/material (P/M) shaft is 4.4 m wide x 3.9 m high. This shaft is unique in that the conveyance will have an onboard driver. The rock shaft is 4.5 m wide x 3.6 m high. Rock will be hoisted with two, ten-tonne overturning skips. In both cases, P/M and rock, the winders were designed for the highest duty cycle, which is encountered during sinking.

Jan 1, 2005

By Chen J, Sun ZY

The present paper gives the design of a new HGMS for magnetic separation of sulphides. The main characteristics of this HGMS are using iron-cladding saddle-shaped magnetic coil for instead of the ordinary magnet, and combining reciprocal-linear motion with vibration to actuate the separation box, and the magnetic field intensity is high up to 2T as well. For improving the magnet system design, a modified finite element method is used to calculate the distribution of magnetic field intensity of separation space of the magnetic coil, and accordingly the calculation results the magnetic leakage coefficient can be determined easily, thus designers apart from the empirical way. KEYWORDS: HGMS, reciprocal motion and vibration, finte element method, saddle-shaped coil.

Jan 1, 1993

By J P. Wyethe, D P. Padayache, B R. Green

The development of an ion exchange process for the recovery of vanadium from solutions containing low concentrations of vanadium and/or slurries is discussed. The process can be used to improve overall vanadium recovery throughout the plant, and/or to reduce the vanadium concentration of waste materials prior to their disposal. The development of the process on a laboratory and miniplant scale is discussed, and includes:selection of a suitable resin with the desired loading and elution characteristics; laboratory-scale testwork to evaluate the use of the resin in both resin-in-pulp and fixed bed configurations; recovery of a high-value vanadium product from the resin eluate; and a preliminary techno-economic assessment of the financial viability of the process.

Jan 1, 2000

By D A. Williams, P J. Chapman

Constructing upstream raises with tailings is an accepted and cost-effective practice in Western Australia, where the climatic conditions are favourable, desiccation (and hence overconsolidation) occurs rapidly due to air drying and there is a perceived low seismic risk. This is in contrast to many other settings, where there is either a positive water balance, high seismicity or a combination of both. In recent times, there has been an increased focus on seismicity in areas of Australia that have historically been considered to be of low seismic risk. The increased focus is driven by two recently published documents used by tailings practitioners and increased awareness from corporate entities, particularly those with mines in high-seismicity regions such as South-East Asia and South America (particularly Chile).The increased awareness has resulted in increased rigour being applied to seismic design of tailings storage facilities (TSFs) in general, and particularly upstream-raised TSFs. This paper compares the results of a seismic stability assessment for an upstream-raised TSF located in the Goldfields region of Western Australia, which has historically been considered a low seismic area, with a seismic stability assessment carried out for a crossvalley TSF containing similar tailings but located in a high-rainfall, high-seismic setting in South-East Asia. The influence of the adopted design earthquake values on the results of the assessments and the potential impact of the maximum design earthquake (MDE) on the design approach is presented for both cases. The results indicate that although the Western Australian site is located in an area thought to have low seismic risk, the screening level analyses suggest that the MDE could result in liquefaction of the tailings materials. Not surprisingly, liquefaction was also indicated for the South-East Asian site. The outcomes of the assessment are also presented.CITATION:Chapman, P J and Williams, D A, 2015. Seismic design of upstream-raised tailings storage facilities in a semi-arid, low-seismicity setting, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 157–162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

A number of cooperative studies have been carried out as preliminary work for drafting a standard for application of granulated slag sand for concrete, and the following conclusions were reached 1 The ten kinds of granulated slag sands pro- duced in Japan satisfy the national standard for fine aggregate in terms of physical and chemical properties. 2 Mortar and concrete tests conducted with granulated slag sand revealed that, although with slight differences in the extent, gran- ulated slag sands used in these tests were applicable'as fine aggregate for concrete, 3 The pumpability test by a concrete pump carried out on concrete with two kinds of now commercially available granulated slag sand demonstrated that the pump pressure feeding is applicable in the same manner as in the case of ordinary concrete. These tests permitted' preparation of a draft standard for application of granulated slag sand, and the results formed the first step toward utilizing this material as a sub- stitute for natural sand.

Jan 1, 1979

By Penney B. K, Baghdadi A. A

An electron probe micro-analyser, controlled by a dedicated mini-computer,has been operating at Imperial College since 1970. The data assessment capability of the computer was limited and, in order to make better use of the information produced by the analyser, extra computing facilities were needed. Following the initiation of a Laboratory Automation Project at Imperial College involving the use of a central computer linked to laboratory type computers and to further more powerful systems,it became possible to carry out much more detailed and extensive mineralogical analyses by connecting the mini -computer to the Laboratory Automation Network. The paper describes the techniques employed including hardware, software, inter- connection, analysis and operating methods.

Jan 1, 1977

By Porter I

Rock mass classification systems have emerged as a powerful tool which can be used for assessing ground conditions and determining support requirements in underground mines. They should not be used as a substitute for complete engineering design, but rather as a supplement to observational methods and analytical study. In general, the use of rock mass classification is attractive, but each classification system has various deficiencies. Use of any particular system should be made only with knowledge of that systems limitations. It is desirable to employ a number of systems and design methods which will allow for comparison and lead to a better understanding of the rock mass condition.The Rock Mass Quality system (Q-System), developed by the Norwegian Geotechnical Institute, and the Rock Mass Rating (RMR) System, Bieniawski, were designed primarily for civil engineering structures. Laubscher et al (1978) further developed the RMR-system specifically for rock mechanics engineering in the mining industry. A method of stope design, which introduces a stability factor for the rock mass and compares this with hydraulic radius, was developed by Mathews et al (1981). This paper reviews the above systems by applying them to stability assessment of crown pillars in two Australian metal mines and provides a critical analysis of the various approaches. In particular each system will be analysed to determine its suitability for use in crown pillar design. The most suitable system(s) will form the basis for future development in crown pillar stability analysis.

Jan 1, 1994

The integration of historic exploration geoscientific data with high precision multi-element and isotope geochemistry can provide explorers fundamental information on mineral potentiality, tectonic setting, source signatures, fluid migration, mineralisation environment and the timing of mineralising events. Such knowledge is crucial for ore modelling and target generation, particularly for concealed ore systems in both brown and greenfields. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Sobek S, Lotzien RM

Although the conventional procedures for designing agitator flotation plants are well-known and reliable, little experience for designing modem pneumatic flotation plants has been gained up to now. A reliable procedure originating from graphic methods for the design of distillation columns is presented. Examples demonstrate on laboratory and semi-technical scale the application of this extremely practical method for designing a fly ash and a magnesite flotation plant.

Jan 1, 1993

Underground mines in Australia and worldwide are extending to greater depths. The effect of depth brings a number of challenges to mining engineers including geotechnical, ventilation, haulage and selection of mining method. The main effects of depth from a ventilation perspective are increased heat and humidity leading to reductions in productivity, occupational safety and health issues and the potential for fatalities. Numerous approaches have been undertaken over the years to mitigate against these effects. In this paper a review of various approaches to improving climatic conditions at a number of mine sites worldwide is undertaken. From these case studies it is argued that for mines at depth with the potential for a climate problem perhaps an alternative design philosophy to the established design philosophy should be utilised. In conclusion, the paper proposes some simple rules of thumb for use in mines with climate problems or the potential for climate problems.

Jan 1, 2008

By KeBler H-W, Seeliger A

Vibration analysis for diagnosis of machines is a powerful instrument for condition monitoring. Especially for diagnosis of antifriction bearings various equipment and techniques have been developed and are available. The envelope analysis is the most reliable method for bearing diagnosis. Different bearing failures lead to different patterns of the envelope spectrum. Checking the amplitudes of characteristic bearing frequencies is mostly not sufficient for a reliable diagnosis. Therefore human experts compare the pattern of the spectrum with typical patterns of bearing defects. In this paper a diagnosis system is presented which imitates this action of human experts. Using a neural net the system not only distinguishes typical bearing defects but also detects unbalance, beating of disengaged machine parts and other kinds of machine failures.

Jan 1, 1995

By N Stockton

Some preliminary results on the secondary leaching of previously heap leached gold ore are presented. Alternative lixiviants for gold comprising chlorine, thiourea and thiosulphate were compared with cyanide using bottle roll tests. Chlorine was subsequently selected for column leaching tests. Column tests at 1.0, 0.1 and 0.01 gL-1 Cl2 at pH 2 were conducted. The results indicated that about 23 per cent of the gold was leached over 45 days using 1 gL-1 Cl2 at pH 2. The experiments conducted proved that the chlorine/chloride system has good potential for further extraction of gold and silver from the existing cyanide heap leach residues and a process for secondary leaching of gold has been proposed. Further testwork is recommended to extend conditions, sample types, and the duration of leaching period.

Jan 1, 2000

By P G. Gaylard

P754 has been an unusual project in that its main aim was to develop a code of practice for metal accounting with the following key objectives:Development leading to an agreed industry standard at corporate governance level Significant improvement of the credibility of metal accounting from deposit to saleable product Development of guidelines for data collection, data analysis, reporting and audit A data analysis toolbox which provides go/no go testing for metal balance data Promotion of industry adoption of these guidelines to improve transparency and financial credibility. Over time, these guidelines may evolve into a code and eventually into a standard Develop and train engineers to become expert in metal balancing and reporting. Papers like this one and the workshop which follows this conference are part of promoting the code for adoption by industry. Developing a code of practice has traditionally been the provenance of professional bodies associated with particular industries û often on a voluntary basis. Given todayÆs industry pressures, it was felt that funding key input might accelerate the development process as well as offer opportunities to research some of the problems and to train some post graduate students in a difficult discipline. In fact, the project has brought together six industry sponsors from a wide range of process types, three research providers, and funded students in South Africa and Australia. The project has also attracted input from the financial community. A textbook to support the application of the code has also been written. The industry sponsors have made the Code and Guidelines available on request to help to facilitate its use by the mineral industry beyond the sponsor group. The Code and Guidelines have already been translated into Spanish and Portuguese which suggests that industry acceptance may happen quite quickly. The main thrust of the code is to integrate commercial and technical performance to a much higher degree. The Check in-Check out (CI-CO) method has been chosen as the vehicle for this combined approach. The mass and metal values used for CI-CO are 'absolute' and provide the basis of financial transfers. The CI-CO process occurs at each transfer of custody - whether between divisions within a company, or between companies. This approach means that measurement of mass and metal flows becomes the critical element of the process and that a quantitative knowledge of measurement accuracy and precision is also essential. This knowledge allows technical differentiation between differences which are within the expected margin of variation and those which must be formally identified as discrepancies and subject to a process of investigation and sign off. Hence, the application of the code for most companies should be more evolutionary than revolutionary, but with substantially more emphasis on measurement and definition of measurement error. Where this can be achieved, it should bring the mineral industry more into line with other industries competing for investment funds, community acceptance and future employees.

Jan 1, 2008