Search Documents

By C. W. Parmalee

The ideal fuel for burning ceramic wares is the one that, among other characteristics, has little or no sulfur. For that reason wood was long considered the most desirable fuel but its high cost has practically eliminated its use except in regions where it is very abundant or other circumstances warrant its choice. The fuels commonly employed are natural and producer gas, oil, and coal. The last named is undoubtedly the most important, not only in this country but abroad. Occasionally anthracite is used but the larger part is bituminous. The quality of the coal used depends on the kind and the value of the products being manufactured. For some materials, such as common brick, hollow block, etc., the quality of the coal is of less importance than in the manufacture of polychrome terra cotta, pottery, porcelain, etc. It is obvious that in burning clays that contain notable amounts of pyrite, marcasite or gypsum, as is the case with many common clays, the sulfur content of the fuel is of much less importance. The permissible amount of sulfur in the coal used will depend on the kind of product being manufactured. "A good sample1 of coal commonly used in pottery ovens has something like this quantity of sulfur: total sulfur, 1.20 per cent.; sulfur in ash, 0.11 per cent.; volatile sulfur, 1.09 per cent." This is based on English pottery practice. Correspondence with a. number of leading manufacturers in this country has produced the following figures: Sanitary Ware.—(a) 1.0 per cent, maximum, (b) 0.5 per cent. Sewer Pipe.—(a) 1.2 per cent., (b) 1.1 per cent, present run, 3.0 per cent, has been used. Terra Cotta.—(a) 0.5 per cent, basis of contract, 1.0 per cent, approximate. Pottery.—1.0 per cent, contract, 1.5 per cent, probable content. Enameled Brick.—1.3 per cent, maximum, (a) and (6) designate different firms giving figures. Since a pottery kiln for sanitary ware will require about 14 tons of coal for a bum, the quantity of SO2 that will be generated from a 1-per

Jan 1, 1920

By F. M. Simonds, E. Z. Burns

The Rawley property is located in the Kerber Creek mining-district, Saguache county, Colorado, at an elevation of 10,600 ft. (See sketch-map, Fig. 1.) Ore was found in this vicinity as early as 1880, and claims covering a large area were located and in many instances patented. The ores, however, being of comparatively low grade, and the nearest railway station, Villa Grove, being some 20 miles away, it is extremely doubtful whether any considerable amount of ore was ever handled at a profit. It is safe to say that several hundred thousand dollars were spent (a large part in building mills) previous to 1902-03. About that time a very capable promoter gathered together a group of these claims and interested some New York people, who had had no previous mining experience, in the purchase of these claims. Following the organization of a company, this promoter became General Manager. As often happens under such conditions, the first step was to erect a mill to treat 100 tons per day. It may not be fair to this enterprise to say that the failure which followed might have been foretold, simply on general principles, but this much is certain—the water supply fluctuates in the course of a season through a wide range and for a considerable portion of the year was inadequate to run this mill at capacity. Further, it is currently reported that some of the mill foundations were placed on ice. However true this statement may be, it is a fact that, when first inspected by us, many of the belts in the mill were held on'their pulleys by means of idlers. A shut-down followed, with a material re-adjustment of interests, at which time we became consulting engineers for the company.

Jan 1, 1914

By Sadao Maruyama

INTRODUCTION Since the big discovery of Kuroko deposits in Kosaka mine, Akita Pref., northeastern Japan in 1959, major Japanese mining companies have been engaged in extensive exploration for the deposits expending large amounts of money. Above all their exploration activities have been particularly fruitful in discovering new deposits in northern Akita Pref. It is estimated that the total ore reserves newly found in the area are at least 50 million tons. Kuroko deposits are the most important ore source of copper, lead and zinc in Japan and have been mined since last century in the said area. Kuroko (black ore) is fine, compact aggregates with sphalerite , glena and barite as principal constituents and chalco- pyrite, pyrite and tetrahedrite as subsequent constituents. The name Kuroko comes from its appearance. It is not rare that total grade of copper, lead and zinc reaches 20 - 30% and the gold and silver content is also fairly good. Accordingly the unit value of the ore is much higher than the ore from other types of deposits. Besides the Kuroko ore, the Kuroko deposits consists of Ohko (yellow ore, massive cupriferous pyritic ore), Keikoh (silicious ore, cupriferous network ore) and gypsum ore. This type of deposit is considered to be not only an important source of base metal but also a source of gypsum and barite. Although the importance of this type of deposit had been commonly recognized, sub-surface nature of the occurrence hampered exploration work. In recent years the improved exploration techniques and increased knowledge of the Kuroko deposits have met with remarkable success in the location of new deposits. This outburst of exploration and dis-

Jan 1, 1970

By O. I. Deschon, Ralph Arnold

Deep drilling was the keynote of the more important developments in the North Rocky Mountain region during 1929, with Montana recording the most important achievement through discovery of three new oil fields. Alberta produced 1,000,000 bbl. of 74 gravity naphtha, showing a considerable gain over 1928, developed a commercial oil pool in Turner Valley and extended that field 8 miles southward. Wyoming's discovery field was deepened to a second producing horizon, giving impetus to deeper drilling, and practically every Wyoming oil field will have a deep test either this year or in the near future. Whereas Montana prospecting has been confined to the shallow plains structures, since the discovery of Kevin-Sunburst field, the coming year will see an active search for new oil and gas pools in sharp-dip structures, following the success of prospecting in the Sweetgrass Hills during 1929. A dozen or more structures have been mapped in North Central Montana, several of these straddling the Alberta border. Four structures tested thus far have all shown commercial oil or gas or both. Sweetgrass Hills The first important development in the Hills area was the Rogers-Imperial gasser, which had an initial of 51,000,000 cu. ft. of dry gas per day, with a rock pressure of 1080 lb. This well is located on a sharp nose running north from the hills into Alberta. Several wells drilled by independent operators on the American side, on the west flank of reserve structure, have developed a total open flow capacity of 30,000,000 cubic feet. The third structure tested in the Hills area is known as Bears Den, where commercial oil was found at the base of the Cretaceous at 2470 ft. The existence of oil in three lower sands has been established by two wells on the top of the structure, these two wells finding gas flows of 10,000,000 and 15,000,000 cu. ft., respectively, in the horizon where

Jan 1, 1930

By F. Z. Schellenberg

A recent visit with the engineering students of the Western University of Pennsylvania to the Keeling coal-mine on the south side of Pittsburgh furnished interesting matter to communicate, as may be the case, however, with regard to the striking features of any of our well-arranged larger collieries; for every mine surely appears unique as a whole, though description fails to give that impression, except in particulars.

Jan 1, 1900

By J. W. Snavely

THE high tension belt conveyor is introducing a new and tremendously expanded era of low cost bulk material handling. High tension belt conveyors are generally those installations involving very long centers, high lifts, or drops, in which the belts are stressed up to their maximum tension values, and further, where the belt construction provides tension capacity far beyond what is possible with conventional belt constructions. With these high tension installations, the magnitude of the forces involved demands careful refinement of accepted design practice in order to achieve optimum balance of all factors. No attempt will be made to evaluate the relative merits of belt conveyor haulage with other means of transportation. For present purposes, it is assumed this has already been done in favor of belt conveyor. Neither will any attempt be made to evaluate the various conveyor belt constructions now available or to balance the advantages of various types of mechanical equipment. It is also assumed that the basic haulage information on which the conveyor design is based is accurate and complete. A sustained maximum, uniform load on the belt at all times must be achieved through proper feed control and the use of adequate surge storage to level the peaks and valleys of any varying demand for the material being handled. General Belt Capacity Considerations The belt conveyor capacity tables published by various belting and conveyor equipment manufacturers vary to a considerable degree, and the ratings given are quite conservative. Of necessity, these published ratings are based on the handling of average materials under average conditions. In applying a high tension belt, all possible capacity from the belt must be obtained in order to hold its width to a minimum and thereby limit the initial cost. Two factors are involved, loading to maximum cross section area and traveling at a maximum practical speed. Belt Loading: Proper treatment of the loading of the belt will result in maximum cross section to the load, and published capacity ratings can be exceeded, sometimes by appreciable margins. On the 10-mile conveyor haul used in the construction of Shasta Dam, California, although the rated capacity of the belt line was 1100 tons per hr, at times the system handled peak loads of 1400 tons per hr, almost 25 pct better than the rated capacity. One of the large coal companies has been able to exceed rated capacity by as much as 50 pct. Loading conditions which must be controlled are: 1. Large lumps must be scalped off and rejected or the load must be primary crushed before being placed on the belt. 2. The material weight per cubic foot must be accurate, must be known for all the materials being handled, and must be known for the complete range of conditions of the individual material being handled. Long centers and high lifts magnify small differences into serious proportions. 3. Uniform feeding to the belt is most important. Various types of feeders are available, which can be used to place a constant predetermined volume of material on the belt, or, where an appreciable range of material weight exists, through electrical control actuated by current demand, to place a predetermined uniform tonnage on the belt. One long slope belt in a coal mine in Pennsylvania is being fed at three separate stations with the controls so arranged that whenever the maximum load is going onto the belt from the first station, the other two stations automatically cut out. Whenever the load from the first station drops back, the other two stations again automatically cut in. 4. Careful design of the chutes and skirts is necessary to get the load centered on the belt with a minimum of free margin along each edge. Some free margin at the edge of the belt is necessary to prevent spillage, but if the load can be kept accurately centered, this free margin area can be reduced, and more material can be carried on the belt. What can be accomplished in this respect will vary widely, depending on the nature of the material being hauled. The chute and skirt design must also protect the belt. 5. The design of chutes and skirts should also get the load traveling in the same direction and close to belt speed, so that the load comes to rest on the belt as quickly as possible. The design of the chutes and skirts is worthy of careful study, and after a system is put into operation it should be experimented with to get the best results. Belt Speed: High belt speeds should be used in high tension work. Obviously, high belt speeds enable haulage on a narrower belt, reducing initial cost. The major portion of belt wear takes place at the loading point and around the terminal pulleys. The

Jan 1, 1952

By George Bain

METHODS of mining building stone of any sort are planned to pro-duce as few fractures as possible, and present a strong contrast to methods of mining metallic ores, which must be crushed eventually and have fractures produced in as great profusion as possible. Shocks transmitted to a stone invariably make it more porous and more permeable and reduce its effective life, therefore methods of mining building stone involve as FIG. 1. THE SUPREME COURT BUILDING, WASHINGTON, D. C. This building illustrates the fine detail of workmanship, unprotected sharp corners and thin edges, and tall narrow columns characteristic of marble structures. These features require exceedingly coherent stone, and preservation of these features for decades or centuries demands many special quarrying precautions to keep absorption to 0.14 per cent or less, a detail not essential to stone for coarser architectural types. few shocks as possible. This is singularly true for marble because marble structures are intended to have long life, greater delicacy of line, more gracefulness and fineness of sculpture than those made from any other structural material (Fig. 1). So that delicate lines may remain in almost perfect preservation for decades, or even centuries, it is important

Jan 1, 1935

By Louise Barton Freeman, Coleman D. Hunter

The total production of oil in Kentucky during the year 1943 reached 7,010,776 bbl., which is more than at any time since 1930. Of this total, 5,287,659 bbl. was produced from the counties west of the Cincinnati arch, 692,359 bbl. from the 18 new pools opened during the year, and 3,260,765 from the Smith Mills pool, which was discovered in August of 1942. This is an important increase in western Kentucky in spite of the low price of crude, and demonstrates effectively the desire of the industry to cooperate in meeting the increased demands made by the war. Western Kentucky Two deep tests were drilled in the Kentucky portion of the Mississippi Embayment this year. Both were drilled to test the St. Peter. One well, drilled in Marshall County by the Adams Oil and Gas Co., did not encounter any St. Peter sandstone but drilled 650 ft. of formation below the position of the St. Peter and above the true Knox dolomite. The other well, in Ballard County, was reported to have tested the St. Peter and to have been temporarily abandoned at 3069 ft. At this depth the well probably was stopped in about the same formation as the Marshall County well. No accurate information is available on the Ballard County well. Several new producing areas were added to the list of fields in the western Kentucky coal basin, in Daviess, Henderson, McLean, Ohio, Union and Webster Counties. The Smith Mills pool was enlarged and production was found in the McClosky (Ste. Genevieve) in addition to the Cypress sandstone from which much of the earlier production had been obtained. There was some interest during the year in testing the Devonian and Silurian formations in the area south and east of the western Kentucky coal basin. In the fall of 1943, a 15 to 20-bbl. well was drilled in Allen County and two more wells are now being drilled. The production was obtained from within a few feet of the base of the Chattanooga black shale, probably in the upper Silurian. One well in Simpson County was drilled completely through the Silurian section before it was abandoned. Several wells were drilled in Logan, Todd and Christian Counties to test the Devonian where it is thinned by removal of the upper formations before deposition of the Chattanooga shale. None of these wells was successful but several other locations are now being tested. The Silurian thins in like manner on the eastern flank of the coal basin as the crest of the Cincinnati arch is approached, and it is along this thinning edge that such fields as the LeGrande, Logsdon Valley, Magnolia, Bowling Green and the Barren County pools were developed. A number of wells were drilled around these old pools in an effort to extend them, some of which were successful. The wells listed this year in Larue, Hardin, Barren, Hart and Warren Counties were drilled in the search for other such fields.

Jan 1, 1944

By Louise Barton Freeman, Coleman D. Hunter

The total production of oil in Kentucky during the year 1943 reached 7,010,776 bbl., which is more than at any time since 1930. Of this total, 5,287,659 bbl. was produced from the counties west of the Cincinnati arch, 692,359 bbl. from the 18 new pools opened during the year, and 3,260,765 from the Smith Mills pool, which was discovered in August of 1942. This is an important increase in western Kentucky in spite of the low price of crude, and demonstrates effectively the desire of the industry to cooperate in meeting the increased demands made by the war. Western Kentucky Two deep tests were drilled in the Kentucky portion of the Mississippi Embayment this year. Both were drilled to test the St. Peter. One well, drilled in Marshall County by the Adams Oil and Gas Co., did not encounter any St. Peter sandstone but drilled 650 ft. of formation below the position of the St. Peter and above the true Knox dolomite. The other well, in Ballard County, was reported to have tested the St. Peter and to have been temporarily abandoned at 3069 ft. At this depth the well probably was stopped in about the same formation as the Marshall County well. No accurate information is available on the Ballard County well. Several new producing areas were added to the list of fields in the western Kentucky coal basin, in Daviess, Henderson, McLean, Ohio, Union and Webster Counties. The Smith Mills pool was enlarged and production was found in the McClosky (Ste. Genevieve) in addition to the Cypress sandstone from which much of the earlier production had been obtained. There was some interest during the year in testing the Devonian and Silurian formations in the area south and east of the western Kentucky coal basin. In the fall of 1943, a 15 to 20-bbl. well was drilled in Allen County and two more wells are now being drilled. The production was obtained from within a few feet of the base of the Chattanooga black shale, probably in the upper Silurian. One well in Simpson County was drilled completely through the Silurian section before it was abandoned. Several wells were drilled in Logan, Todd and Christian Counties to test the Devonian where it is thinned by removal of the upper formations before deposition of the Chattanooga shale. None of these wells was successful but several other locations are now being tested. The Silurian thins in like manner on the eastern flank of the coal basin as the crest of the Cincinnati arch is approached, and it is along this thinning edge that such fields as the LeGrande, Logsdon Valley, Magnolia, Bowling Green and the Barren County pools were developed. A number of wells were drilled around these old pools in an effort to extend them, some of which were successful. The wells listed this year in Larue, Hardin, Barren, Hart and Warren Counties were drilled in the search for other such fields.

Jan 1, 1944

By N. E. Norman, R. Stier

The mining industry is continually seeking out new and better underground mining techniques. One of the most recent-also, perhaps, the most significant-of the new concepts in underground mining is the use of mechanical rock-boring machines. And one of the problems that concerns us all in this matter is the cost of mechanical rock tunneling. To help answer the oft-quoted question "What will it cost me?" the following pages deal with the operating costs of so-called "medium to medium hard rock" boring machines-i.e., those designed to meet the drilling requirements in 8000 psi to 25,000 psi rock. A few machines are capable of drilling hard rock above 25,000 psi, but the economics of mechanical tunneling in rock that hard is limited at the present time. [ ] For mechanical rock tunneling, there are five main cost factors influencing the expense: Capital Investment, Cutters, Labor, Power Requirements, and Maintenance. These factors give us a good basic picture of the cost of excavation, although muck handling, erecting supports, and other costs directly related to conventional tunneling and mechanical boring enter into the final picture.

Jan 6, 1967

By V. F. Leferrer

A new process for the treatment of silver crusts from desilverization of lead has been developed by Societe de Penarroya. The zinc contained in the crusts is recuperated by vacuum distillation at low temperature. The use of special retort crucibles is avoided. AT Noyelles-Godault the Parkes process (zinc addition to a silver-bearing lead melt) is used to desilverize lead bullion from the blast furnace. The crust which rises to the surface of the bath is removed and pressed by a well-known process in a press of the Howard type. The pressed crust, called zinc crust or silver crust, contains 10 pct Ag, 30 pct Zn, and 60 pct Pb. It is melted under a salt bed in a small, narrow, and deep kettle heated only in its upper part. A liquid concentrated alloy is obtained which is called T.A.C. in France (triple alliage concentr6) analyzing approximately 25 pct Ag, 65 pct Zn, 8 to 10 pct Pb, and 1 to 1.5 pct Cu. This T.A.C. is a real metallic alloy, completely deoxidized, and can be stored indefinitely. The process used at Noyelles-Godault consists in distilling this alloy in a tight furnace, under low vacuum and at low temperature, so that only the zinc distills and is condensed into liquid form. The residual silver-bearing lead is almost entirely free from zinc and oxidized dross. The vacuum dezincing equipment, see Figs. 1 and 2, consists of: 1) A furnace, constituted of a casing of steel plate lined with refractory bricks, heated internally by means of graphite resistors. The temperature of the furnace is measured by a thermocouple device and controlled by an automatic temperature regulator which acts upon the flow of the current passing through the resistors. Two doors, numbered 1 and 2 in Fig. 2, are provided for, one for charging the T.A.C., the other for tapping the high silver-bearing lead. 2) A condenser, and an ordinary room lined with good heat conductor refractory material. This condenser is provided with a graphite resistor which serves to bring to temperature when starting the furnace. A thermocouple records the temperature of the zinc melt and controls the temperature in the furnace, that is, the flow of current through the resistors, by means of the above mentioned regulator, so that the distillation rate in the furnace does not exceed that of the condensation. The condenser is connected to the vacuum pump by a filter. The whole equipment should, of course, be fluid-tight. The operation is carried out under a vacuum of about 10 mm Hg.

Jan 1, 1958

By R. E. H. Pomeroy

Early in 1917, it became evident, owing to existing and pending market conditions, that a substitute for crude petroleum must be found for firing the smelter furnaces. After a review of the plants then existing, it was deemed advisable to depart from their practice and to adopt the following described system of distributing pulverized coal to the furnaces. The principal advantages of the proposed system, which influenced this decision, were: (I) Equal safety; no pulverized coal is stored at the furnaces; (2) greater ease of operation, furnace fires being controlled by regulating valves in burner branches, as in gas firing; (3) better organization; all machinery, including pulverized coal feed, is under one roof, and the organization is separate from the furnace department; (4) greater cleanliness; all machinery is under vacuum; (5) greater flexibility of application, the coal and air mixture can be piped where needcd. The design of the plant is the result of the combined efforts of the local engineering staff and of the machinery manufacturers. Many new features were embodied in this design to insure greater safety, cleanliness, and efficiency of handling. After 14 months of continuous operation, the plant has proved entirely satisfactory. The building is of structural steel, covered with corrugated steel, with many windows and is painted light gray inside and out. The building floor is of concrete with ample drains to the sewer, and the building is equipped with fire and service water piping. Fig. 1 shows the east side of the building and the incline conveyor from the raw-coal bins. The plant is operated entirely by electric power. All alternating current is 550 volts, 3-phase, 60 cycles. The pulverized-coal feeding niotors and control mechanism are operated by 220-volt direct current supplied by motor-generator sets in the building. Autamatic push-

Jan 1, 1921

By H. E. Mills

THE local auditorium of a little Alabama mining town was crowded with expectant men, women and children, as the bulletin board had announced the addition of visiting entertainers to supplement the local talent and motion pictures which usually made up the program of the regular monthly safety meeting. In the audience, near the stage, sat a group of bright-faced boys in boy scout uniforms, discussing the picture just completed. As the lights flashed on a crash and scream was heard from the outside, a shrill whistle and word of command from the scoutmaster, and five of the scouts ran out of the hall, while the mine super-intendent stepped on the stage and requested everyone to keep their seats. The scouts returned, three of them carrying a limp figure in their arms, while the other two cleared the doorway and aisle of excited spectators. They marched to the stage and, placing the apparently badly-injured boy on the floor, proceeded to give an expert demonstration of first aid to the injured. The scoutmaster then explained to the audience that the whole affair had been arranged for their benefit, and invited the local first-aid men to come up on the stage to examine and criticize the boys' work. This gave an opening for several talks on the value of first-aid training and accident prevention, which is the main object of the monthly meetings. This demonstration was given by the first-aid team of Troop One, and the entertainment was provided by members of Troop One and Twenty-eight of the Bir-mingham Scout Council, organized by the writer for the purpose of promoting interest in the welfare and safety meetings in the mining villages of the State. During the past year they have visited a number of such meet-ings and presented programs similar to the one men-tioned above. However, in order to assure a good attendance, entertainment features must also be pro-vided, and the serious part of the evening program was interspersed with excellent vocal and instrumental mu-sic, dancing and novelty acrobatic acts furnished by the visiting scouts. In addition to the numerous first-aid teams of the Birmingham Council, there are hundreds of scouts scat-tered throughout the mining district whose knowledge of first aid, safety first, life-saving, personal health and public health are a constant source of protection to their community. All of these subjects are covered by merit badge pamphlets and are required of an eagle scout.

Jan 2, 1927

By M. W. Ditto

THe conversion of the beehive coke plants, in this country, to byproduct plants has been slow, because the coal supplies were near the centers of the steel industry. With the growth of this industry, especially with its development around Chicago, it became necessary to transport large tonnages of coal from the eastern districts and then convert it into coke. The losses due to transportation costs were partly offset by the value of the byproducts recovered. To save the transportation costs, it was desirable that the coal deposits of Indiana and Illinois be utilized. This coal had always been classified as non-coking; it was also considered unsuitable for the metallurgical field because of the high ash and sulfur contents. The conditions, however, were promising enough to start experimental and development work, which crystallized in the design of the Roberts coke oven. The fundamental features of most coke ovens, with respect to the application of heating gas and the recovery of byproducts, are the same and, in the last few years, the tendency has been toward the better application of heating to the walls, higher thermal efficiency, and, by the control of heating conditions, the increase of byproduct yields. Structural features also have been improved and the use of high-grade refractory material has allowed the use of higher temperatures with the resulting higher rated capacity per oven per day. Great improvements have been made in both recuperators and regenerators, particularly with reference to the individualizing of each oven with respect to its adjacent oven, so that each can be operated as a unit if desired. The highest development of the flue type of oven has been applying individual regenerators for the recovery of waste heat. After some research work, it was found that the high-volatile Illinois coals could be utilized for coke by obtaining the better application and control of the heating conditions in the oven. Most of this high-volatile coal that had been used gave a good coke structure under certain conditions. The fact that coke was occasionally made from this coal, demonstrated the possibiity of making coke from it at all times pro-

Jan 1, 1923

By M. W. Ditto

THe conversion of the beehive coke plants, in this country, to byproduct plants has been slow, because the coal supplies were near the centers of the steel industry. With the growth of this industry, especially with its development around Chicago, it became necessary to transport large tonnages of coal from the eastern districts and then convert it into coke. The losses due to transportation costs were partly offset by the value of the byproducts recovered. To save the transportation costs, it was desirable that the coal deposits of Indiana and Illinois be utilized. This coal had always been classified as non-coking; it was also considered unsuitable for the metallurgical field because of the high ash and sulfur contents. The conditions, however, were promising enough to start experimental and development work, which crystallized in the design of the Roberts coke oven. The fundamental features of most coke ovens, with respect to the application of heating gas and the recovery of byproducts, are the same and, in the last few years, the tendency has been toward the better application of heating to the walls, higher thermal efficiency, and, by the control of heating conditions, the increase of byproduct yields. Structural features also have been improved and the use of high-grade refractory material has allowed the use of higher temperatures with the resulting higher rated capacity per oven per day. Great improvements have been made in both recuperators and regenerators, particularly with reference to the individualizing of each oven with respect to its adjacent oven, so that each can be operated as a unit if desired. The highest development of the flue type of oven has been applying individual regenerators for the recovery of waste heat. After some research work, it was found that the high-volatile Illinois coals could be utilized for coke by obtaining the better application and control of the heating conditions in the oven. Most of this high-volatile coal that had been used gave a good coke structure under certain conditions. The fact that coke was occasionally made from this coal, demonstrated the possibiity of making coke from it at all times pro-

Jan 1, 1923

By S. Brunauer

The hydration of portland cement is treated as a chemical reaction and the changes in matter, in energy and the rate of change of the process are discussed, Portland cement is a mixture of four major and at least as many important minor constituents. In the hydration process, the four major compounds (trical-cium silicate, dicalcium silicate, tricalcium alumi-nate and tetracalcium aluminoferrite), plus gypsum and water form five or six new compounds. In spite o the great complexity of the reaction, considerable progress has been made in its understanding, primarily with the help of such research tools as X-ray diffraction and electron microscopy. The rate of the reaction can be followed by direct and indirect methods of measurements. The effects o composition, particle size (or specific surface), temperature and water-cement ratio on the rates of hydration are discussed. The hydration of portland cement is a chemical reaction accompanied by such highly important physical phenomena as heat evolution, setting and hardening. It is a vast and complex subject, on which hundreds of papers have been published. At the time of the writing of this paper, in October 1962, a two-volume book, which alone contains dozens of papers pertaining to cement hydration appeared in print.' The present paper deals with a few aspects of this vast subject, and the selection was not easy. The work reported here deals with some of the most recent investigations in the field. In any chemical reaction, the physical chemist is primarily interested in three things: changes in matter, changes in energy and the rate of change of the process or the speed of the reaction. This is true also of the chemical reaction between portland cement and water, and all three aspects of the reaction will be discussed. These three aspects are of vital interest to the engineer as well. Portland cement is not a cementing material — the hydration products, the new materials which form in the reaction, have the cementing action. The energy changes manifest themselves in a considerable evolution of heat, which may be useful or harmful. It is useful, for example, in winter concreting, but in very large concrete structures like dams, a large evolution of heat, which cannot be easily dissipated, may produce distress in the structure. Primarily for such a purpose was the Type IV or low heat portland cement developed. The speed of the chemical reaction is important because it determines the time of setting and hardening. The initial reaction must be slow enough to permit placing of the concrete before setting occurs. On the other hand, after the placing of concrete it is often highly desirable to obtain as rapid chemical reaction as possible. For this purpose the Type 111 or high early strength portland cement was developed. CHANGES IN MATTER Portland Cement: In a basic investigation, before one begins to study a reaction, one either knows the quantities and compositions of the starting materials, the reactants, or one determines them. This is obvious; the chemist expresses the changes in matter that occur in a reaction by a chemical equation, which has the quantities and compositions of the reactants on the left side of the equation and the quantities and compositions of the reaction products on the right side. The first question is then what to put on the left side of the equation in the reaction between portland cement and water? It is not very easy to answer this question. Portland cement is not a single chemical compound but a mixture of many compounds. Four of these are considered the major compounds, and at least four of the minor compounds also play important roles in the hydration reaction. In order to avoid complicating matters, the present discussion will be restricted primarily to the four major compounds, which constitute usually more than 90% of a portland cement. The relative amounts of these compounds vary from cement to cement. Actually not only the amounts but the compositions of these constituents also vary to some extent, but the variation in composition of the individual components will be neglected for simplicity.

Jan 1, 1963

By Henry R. Linden

The demand for natural gas continues to increase at higher than anticipated rates, partly because of its widening price advantage over most other fossil fuels when the cost of air-pollution control is included. However, there are clear indications that the natural gas supply from the conliguous 48 states and continental shelves will not keep up with this rapid growth in demand indefinitely. Projections are presented which define the extent of potential deficiencies from the 1970's to the year 2000. Among the sources of supplemental gas - imported pipeline natural gas from Canada and Mexico, tanker import of liquefied natural gas, and synthetic pipeline gas from coal and oil shale -by far the most abundant at potentially competitive costs is pipeline gas from coal. The state of development and relative economics of the various coal gasification processes are reviewed. It is shown that synthetic pipeline gas could become a very substantial market for bituminous coal and lignite at current mine-mouth prices - 60-70 million tons of coal for each trillion cubic feet of synthetic pipeline gas produced. This corresponds to only slightly more than the current annual increase in gas demand. Although annual discoveries (gross additions to proved reserves) of natural gas in the United States are still on a general upward trend from the current level of 22 trillion cu ft annually, most forecasters do not expect this to increase substantially in the foreseeable future. For example, the updated (to include 1966 and 1967 data) mathematical model of natural gas discovery and production in the U.S. developed by the Institute of Gas Technology (IGT)' projects that discoveries will level out at about 25 trillion cu ft annually in the late 1970's and during the 1980's and then decline to about 21 trillion cu ft by the year 2000 (Fig. 1). This adds up to a new supply for the period 1968-2000 of about 790 trillion cu ft. Experts who usually reflect the producers' viewpoint, such as Radford L. Schantz of Foster Associates,* are relatively more pessimistic. In contrast, a forecast just made by the U.S. Dept. of the Interior is much more optimistic.3 It assumes an increase in gas discoveries of 2.2% per year over the period 1965-80, reaching about 30 trillion cu ft in 1980. If this rate of increase were extended to the year 2000, annual discoveries would reach 46 trillion cu ft at that time, for a total over the period 1968-2000 of about 1100 trillion cu ft. To these forecasts of new gas discoveries must be added proved reserves of roughly 290 trillion cu ft,4 bringing total U.S. supplies for the rest of the century to nearly 1100 trillion cu ft (IGT) and possibly as high as 1400 trillion cu ft (U.S. Dept. of the Interior). This is approximately the same range as that of two estimates of total remaining recoverable natural gas supply: Potential Gas Committee, 980 trillion cu ft5 and IGT, 1450 trillion cu ft.6 Only the 1965 estimate by the U.S. Geological Survey7 suggests that economically recoverable natural gas supplies will not be exhausted around the end of the century. These forecasts are, naturally, based on the assumption that changes in technological, economic, and regulatory environment as they affect the gas industry will be of an evolutionary, not revolutionary, nature. The various forecasts of potential natural gas supply must now be compared to forecasts of natural gas demand (Table I). The general consensus is that the recent Future Requirements Committee projection to 1990' (extended to the year 2000 by the most recent U.S. Bureau of Mines (USBM) projection9) represents the minimum gas requirements (Table 11). They add up to a total of 1030 trillion cu ft for the period 1968-2000. Even this minimum anticipated gas demand exceeds the total remaining supply estimate by the Potential Gas Committee and would nearly exhaust the proved reserves plus new discoveries projected by IGT. The supply situation would appear much tighter if the demand projections of the Texas Eastern Transmission Gorp.10 and the American Gas Assn.(A.GA.)'' were used (Table I). Yet, these higher forecasts probably do not include the effects of such new markets as gas fuel cells, use of liquefied natural gas as a transport fuel, etc. They also may not fully reflect the impact of air quality control on the fuel market. Obviously, the probable discrepancy between projected supply and demand can only be accommodated in four ways. 1) Rapid increase in exploration and drilling activity to provide new supplies in the amount projected by the optimistic U.S. Dept. of the Interior forecast, coupled with an increase in net pipeline imports from Canada and Mexico from the present 0.5 trillion cu ft per year

Jan 1, 1970

By Rodney Lawrence, Tim Hackett

INTRODUCTION The western USA contains significant coal reserves in seams 10 feet or more in thickness which lie too deep for surface mining. As part of a demonstration of the use of two legged shield supports in the United States, Kaiser Steel Corporation, under contract to the US government used the longwall method to mine a ten foot thick coal seam in New Mexico. Caliper type shield supports and double drum shearers were used in three longwall panels. During the test, technical, production, and safety data were collected to objectively evaluate the performance of the shields in mining the thick coal seam. This paper presents discussions of practical operating experience and summary statistics to aid the mining industry in planning longwall mines in similar conditions.

Jan 1, 1981

While coal was mined in New Mexico in 1860, production was on a small scale during the period considered here, and Table 77 contains all the data found. [ ]

Jan 1, 1942

By Walter Crooke

Regenerative hot-blast stoves are now in general use in all parts of the world, and are so well understood and appreciated, that I need not take up your time with an account of their history and introduction into the United States. My object in writing this paper is to give you a short description of a stove that is now being very favorably received and adopted here (see drawing). The stove was first introduced into this country in 1887 by M'Clure & Shuler (now M'Clure & Amsler), who have the management of the patent right in the United States. The English design had to be modified to suit the exigencies of American blast-furnace practice, which, in many respects, widely differs from our English experience. In the first place, the fire-bricks used in America expand to an extent unknown in England, and it became necessary to make special provision for this by increasing the number of cross-walls, and by leaving a space at the top of the stove through which the lining could expand. The expansion laterally was, however, more difficult to provide for, as the combustion-chamber in the center, being the hottest part of the stove, must necessarily expand more than the outer walls, and therefore tend to squeeze up the flue-openings. On first introducing these stoves to American ironmasters, a feel ing seemed to prevail that a " four-pass " stove did not utilize the whole of its surface. They also had an idea that the " two-pass " stove let the burning gas go before all the duty had been extracted from it; so that it was found neceseary to design a stove of a special character to suit their wishes. Hence the "three-pass" chimney top stove now before your notice, the advantage claimed for which is that each stove is independent, requiring no underground chimney flue or stack, and can be erected at a very light cost. The working of these stoves has proved to be very successful wherever they have been introduced.

Jan 1, 1891