Search Documents

By Albert A. Smith

The creep properties of metals have assumed increasing importance in recent years and many investigations have been made on various phases of the problem. In the past year the annual lectures of the Institute of Metals Division1 and the Iron and Steel Division2 were concerned with this subject, and are excellent reviews. For many years the creep properties of lead and lead alloys have been investigated at the Central Research Laboratories of the American Smelting and Refining Co., and it is hoped that the present paper will contribute knowledge of some of the factors that influence creep. Lead, being a metal that recrys-tallizes readily at room temperature, is an excellent material upon which to investigate creep phenomena because of the simplicity of the apparatus needed, and it might be expected that results would apply to some extent to elevated-temperature tests of other metals. Material The creep tests of this investigation were all made on high-purity lead (99.9998+ Pb) in which the only impurity that could be detected by spectrographic and chemical means was approximately 0.0001 per cent Fe. Flat strips, 0.750 in. wide by 0. 100 in. thick, were prepared by extruding 2-in. dia. cast billets at a temperature of 250°C. This gave a material of 2 to 3 mm. average grain size with a tensile strength of j.400 lb. per sq. in. when tested at a straining rate of 5 per cent per minute. With this extremely soft material, great care was necessary in handling the specimens, to avoid distortion and subsequent recrystallization. The creep tests at 30°C. were conducted in a constant-temperature room, specially built for the purpose in the basement of an office building in which there was no moving machinery, and no vibration was detectable under the most severe conditions of shock in the adjacent surroundings. The room was well insulated and heated electrically, control being by means of a de Khotinsky regulator operating a relay. Maximum temperature variation over a period of several years has been ± 1/2°C. Specimens of the extruded strip, 16 in. long, were used for test purposes with no reduced gauge section, thus eliminating any distortion due to machining. The method of clamping and supporting the specimens is shown diagrammatically in Fig. 1. The gauge marker for the measurement of extension consisted of an aluminum strip, 0.050 in. thick by 0.75 in. wide, one end of which was ground and sanded to a precise knife-edge and fastened to the specimen by suitable pins. After the strip was fastened in place a fine scratch was inscribed just below the knife-edge by means of a sharp teasing needle. Just below this gauge scratch a short vertical mark was made so that the same point could be located and read each time. Several hundred specimens have been prepared by this method, and it was found that with experi-

Jan 1, 1941

By Albert A. Smith

The creep properties of metals have assumed increasing importance in recent years and many investigations have been made on various phases of the problem. In the past year the annual lectures of the Institute of Metals Division1 and the Iron and Steel Division2 were concerned with this subject, and are excellent reviews. For many years the creep properties of lead and lead alloys have been investigated at the Central Research Laboratories of the American Smelting and Refining Co., and it is hoped that the present paper will contribute knowledge of some of the factors that influence creep. Lead, being a metal that recrys-tallizes readily at room temperature, is an excellent material upon which to investigate creep phenomena because of the simplicity of the apparatus needed, and it might be expected that results would apply to some extent to elevated-temperature tests of other metals. Material The creep tests of this investigation were all made on high-purity lead (99.9998+ Pb) in which the only impurity that could be detected by spectrographic and chemical means was approximately 0.0001 per cent Fe. Flat strips, 0.750 in. wide by 0. 100 in. thick, were prepared by extruding 2-in. dia. cast billets at a temperature of 250°C. This gave a material of 2 to 3 mm. average grain size with a tensile strength of j.400 lb. per sq. in. when tested at a straining rate of 5 per cent per minute. With this extremely soft material, great care was necessary in handling the specimens, to avoid distortion and subsequent recrystallization. The creep tests at 30°C. were conducted in a constant-temperature room, specially built for the purpose in the basement of an office building in which there was no moving machinery, and no vibration was detectable under the most severe conditions of shock in the adjacent surroundings. The room was well insulated and heated electrically, control being by means of a de Khotinsky regulator operating a relay. Maximum temperature variation over a period of several years has been ± 1/2°C. Specimens of the extruded strip, 16 in. long, were used for test purposes with no reduced gauge section, thus eliminating any distortion due to machining. The method of clamping and supporting the specimens is shown diagrammatically in Fig. 1. The gauge marker for the measurement of extension consisted of an aluminum strip, 0.050 in. thick by 0.75 in. wide, one end of which was ground and sanded to a precise knife-edge and fastened to the specimen by suitable pins. After the strip was fastened in place a fine scratch was inscribed just below the knife-edge by means of a sharp teasing needle. Just below this gauge scratch a short vertical mark was made so that the same point could be located and read each time. Several hundred specimens have been prepared by this method, and it was found that with experi-

Jan 1, 1941

By Robert Adams

Secondary or scrap materials appear at all stages in the industrial process and in a bewildering variety of forms, grades, and values. It is useful to begin analyzing them by dividing the broad concept of "Secondary Supply" into three parts First, the concept must encompass the stock, or pool, of secondary materials. In the process of satisfying his wants, man produces desired products from the materials and natural resources found around him. As long as the rate of production is greater than the rate of obsolescence of a given product, the total stock or pool of materials embodied in that product will increase in size This stock concept relating to secondary materials is directly analogous to the "resource" concept used for primary raw materials in the preceding chapter, and includes all materials embodied in existing products (Obviously, this excludes those materials which are destroyed in the consumption process, viz , fuel oil burned to provide heat.) Consumption of a primary material in a productive process tends to reduce the resource base of that primary material In direct contrast, however, the production or use of products increases the resource base of the secondary material. Thus, we find that a country which has no resource of a primary material can, by importing products that contain the material, build up a large enough stock to provide a basis for secondary recovery. The estimated growth of the pool of copper in use in the United States through 1967 is shown in Table 5.B.1.a The estimate of 39 3 million tons at the end of 1967 includes only technologically recoverable copper and is, therefore, somewhat less than the stock concept described previously, which does not distinguish between recoverable and unrecoverable material. Nevertheless, Table 5 B.1 does give an idea of how a nation's secondary resource of a material can grow over the years. A second aspect of the concept of secondary supply is the generation of secondary materials. This includes materials generated as scrap in production as well as the movement of a material out of the stock of existing products via wear, damage, or obsolescence The quantity of materials generated is usually either nearly or completely independent of the technologic capabilities and economic forces which prevail in the secondary recovery market.b The justifications for and the qualifications to this statement are considered later. The final aspect of the concept of secondary supply consists in the secondary recovery process It is at this point that the technologic and economic forces of the secondary recovery market become the controlling fac-

Jan 1, 1976

By B. I. Routh

A STUDY of the effects of temperature on the gel strength of drilling muds is a natural outgrowth of the present era of deep drilling. The control of the gel solids' is now considered important because it affects the wall-building qualities; the suspension of weighting material; the removal and release of sand, cuttings, and gas; and the control of cav-ing formations. With regard to the effect of temperature on gel strengths Herrick2 states: "Temperature variation within ordinary limits does not have much effect on yield points." Lewis, Squires and Thompson3 investi-gated one clay and found no marked change with temperature in either yield point or mobility. Reed4 found that potassium bentonite showed a great increase of gelation with increase in temperature and qualitatively there occurred a marked increase in viscosity upon heating. The apparatus used in these experiments consisted of a Stormer viscosimeter, Marsh funnel viscosimeter, rectangular and cylindrical shearometers, Mudwate hydrometer, and other minor laboratory equip-ment. The various methods of measuring viscosity and gel strength have been extensively described by Evans and Reid.5

Jan 1, 1938

By W. C. Roberts-Austin

The subject with which the Council of the American Institute of Mining Engineers has entrusted me is one of much interest. It has been so admirably treated in America by Prof. Carl Barus* that I should have hesitated to deal with it had not the adoption of pyrometric methods in England recently occupied much attention, especially in relation to metallurgical industries and research. I shall endeavor to show what is the present state of our knowledge of practical pyrometry by briefly tracing the history of the efforts which have been made to measure high temperatures. This paper will, therefore, be limited to the consideration of those forms of appliance which have either marked distinct stages of advance, or have remained in use with more or less modification through a considerable range of time. The earliest pyrometers were essentially thermoscopes, and although their graduation presented great difficulties, their importance as affording a means for the measurement of high temperatures has been recognized for centuries. It would be difficult to illustrate this better than by a brief record of the testimony which has from time to time been offered by those who have had to apply the heat of furnaces in research or in industry, and it is mainly for the sake of the light incidentally thrown on the progress of both that the following historical notes are offered. In the eighth century, Geber, the chemist, wrote a treatise on furnaces, and showed that he was familiar with many and varied means of applying heat; but he points to the difficulties that are met with in conducting operations at high temperatures, which he attributed to inability to measure heat, his actual words being: " sed quoniam non est res ignis, quae mensuari possit." t

Jan 1, 1894

By James R. Jones

The concern for air pollution goes back centuries as will be seen from this quotation : "Strife and coal, it seems, have a hand-in-hand historical relationship. It was thought by some . . . in the Middle Ages that burning coal filled the air with dangerous poisons. So great was the concern that in 1306 King Edward I of England passed the first and unquestionably the harshest air pollution legislation edict that history will record. His proclamation declared the use of coal an act punishable by death." As related to coal mining, the air pollution problem is primarily that of its customer when using the fuel. Thus the major impact relates to markets for coal rather than the actual mining operation itself. In the vicinity of the coal mine the problem is principally related to fugitive dust from roads, transfer facilities, loading facilities, crushers, etc., and particulate matter (dust or fly ash) from thermal dryers and air cleaning tables. FUGITIVE DUST Most state air pollution regulatory agencies now have rules and regulations requiring control of fugitive dust. Fugitive dust has been defined by the courts as particulate matter other than that emanating from a specific point such as a stack or chimney. A typical air pollution control agency regulation reads as follows : “Fugitive Dust " "No person shall cause, suffer, allow, or permit any material to be handled, transported, or stored; or a building, its appurtenances, or a road to be used, constructed, altered, repaired or demolished without taking reasonable precautions to prevent particulate matter from be- coming airborne. Such reasonable precautions shall include, where applicable, but not be limited to the following:

Jan 1, 1981

Jan 1, 1909

By J. L. Brimhall, R. A. Huggins, M. J. Klein

IN a recent paper1 it was shown that small additions of magnesium, copper, and oxygen decrease the stacking fault probability in plastically deformed silver. Correlation of :X-ray data with measurements of the twinning frequency and metallographic observation of slip lines indicated that this effect may be due to an increase in the relative stacking fault energy. It is the purpose of the present note to report experiments on these alloys of known stacking fault probability that relate to the stacking fault contribution to electron scattering in silver. There has been a considerable amount of disagreement in the literature concerning the contribution of dislocations to electrical resistivity in metals. Calculations relating to the scattering of conduction electrons by the dislocation core, its strain fields, and related effects have been made by several authors.2-5 In addition, experimental work on Cu,3,6-10 Ni,11 and Ni-Co alloys1:! has shown that dislocations in those materials exert an anomalously large effect on resistivity, this effect being related to the presence of extended dislocations. The problem of the scattering due to the stacking fault region between partial dislocations has been treated theoretically using several different procedures.13-'0 The results of these calculations show a wide range of predicted values, from rather large to completely negligible, due to the models and the approximations involved. Almost all of this work has been applied to the specific problem of scattering in copper. The more complete theoretical treatments depend rather critically. on the shape of the Fermi surfaces and the effective mass parameters. The scattering from stacking faults might therefore be expected to vary significantly from one metal to another. Unfortunately, sufficiently accurate information is not available .which would allow one to have any confidence in a theoretical prediction of the scattering in the case of silver. Resistivity measurements were made on small wire specimens of vacuum melted high purity silver and several dilute alloys. These measurements were made at approximately 20°C, with great care being given to temperature measurement and corrections. At such temperatures phonon scattering is significantly greater than imperfection scattering. However, the experimental technique was such that measurements on similarly treated samples were reproducible to better than 2.4 X 10-9 ohm-cm, which was satisfactory for this work. Values of the stacking fault probability and the increase in resistivity after severe plastic deformation are given in Table I. The increases in resistivity resulting from plastic deformation agree quite well with previous work on silver.14,21-26 In addition, it has been previously found that interetitials and vacancies in silver anneal out well below room temperature, so that the residual imperfection scattering in these experiments could be expected to be primarily associated with dislocations;. It is seen from the data in Table I that large changes in stacking fault probability are accompanied by differences in resistivity due to imperfection scattering of only a few percent. If the scattering of conduction electrons by extended dislocations is primarily due to the area of the stacking fault region independent of the stacking fault energy, and not the core and strain fields associated with partial dislocations, the resistivity increase should be proportional to the product of the dislocation density and the stacking fault width, as is the stacking fault probability. Therefore, the imperfection scattering caused by plastic deformation of the alloys should be considerably smaller than that found in the pure silver. Since this was not observed, these results sugegest the possibility that stacking faults do not themselves contribute appreciably to the electrical resistivity of silver deformed at room temperature. An alternative explanation of these observations is that the scattering by the stacking fault is roughly proportional to the stacking fault energy, rather than being determined by the total area of such faults. Sufficient evidence is not yet available to separate these two possibilities. This work was supported by the Office of Naval Research.

Jan 1, 1962

Jan 1, 1924

By AIME AIME

No democracy such as ours, can ever be prepared for war, because we could never conceivably be the aggressor. The aggressor prepares in secret, designs his new tactics, and invents and makes new equipment and selects the time to strike. If a democracy prepare done year and the war came later, all that it had one would have to bed one over. All that England has today in the way of effective armament has been invented, designed, made, and the crews trained since the war began, because the totalitarian aggressor introduced new types of equipment and new techniques.

Jan 1, 1941

By H. H. Campbell

Many attempts have been made to write a formula by which to calculate the strength of steel from its chemical composition, but most of these endeavors have failed because there were too many disturbing conditions. It is idle to collect from the pages of trade-papers, books, or the proceedings of scientific societies, a multitude of observations. The combination of such results will simply show that steel of the same composition will vary in tensile strength through wide limits—a fact that has been known for generations. That cold-working, overheating, and many another form of heat-treatment alter fundamentally the strength of steel, is ancient history, although it is only recently that the microscope has pointed out the road to an explanation of the phenomena. It mag be urged that the microscopic structure must betaken into consideration in any formula giving the ultimate strength, but from the standpoint of the present investigation this is unnecessary. We are trying to determine primarily, not what changes in ultimate strength may be made by variations in the condition of carbon, but what effect is produced by changes in the amount of carbon, when its condition remains constant. For such an inquiry, in order that the condition of the carbon should remain as nearly uniform as possible, it is essential that all testrpieces be made under the same conditions; and it is believed that the tests described in this paper satisfy that requirement. The investigations were made at the works of the Pennsylvania Steel Company, Steelton, Pa.; the ingots from which the tests were made were 6 in. square in every case; they were heated in the same furnace and forged at the same ham-

Jan 1, 1905

By Leo F. Reinartz

Part II of a four-part series on the history of steelmaking in the US, points out the inadequate safety and living conditions that existed in steel mills at the turn of the Century. Also defined are furnace and process developments. OPERATIONS in steel plants today are highly mechanized. Men work in light, clean, orderly melting shops, making it difficult for old timers to convince young men that primitive, hazardous conditions existed in steel plants at the turn of the century. Working conditions then were very poor as compared to present day standards. In small plants especially, sanitary, locker, and washroom facilities, first-aid practices and stations were un- known Accidents were frequent and severe. Workers had a fatalistic attitude toward getting hurt. He who had an accident was looked upon as a hero. A dirty bandanna often served as a bandage. Infections were frequent. Electric cranes were in their infancy and broke down often Cables had not as yet replaced chains. Pig iron and scrap iron were loaded by hand in the stockyard, and stockyard locomotives were un- known; mules served as the usual motive power. It was not unusual to see recorded a delay of ½ hr in charging a furnace because of a balky mule. Furnace operations A few plants had primitive charging machines, but most furnaces were charged by placing scrap or pig iron on the paddle of a long peel, which rested on a bar across the furnace door opening. Laborers at the handle end of the peel, using the bar as a fulcrum, would heave the material into the furnace by a down and sideward motion of the peel handle. In time they became expert in placing these materials in the furnace, but it was hard, hot work, and a long time was required for charging. Cold charges of 25 tons required more than 12 hr for melting and re- fining the steel. Ports, doors, and frames were not water cooled. The charging and working area in front of the furnace was covered with steel plates. They were hot and often warped by the intense heat of the un- insulated checker chambers directly below. In the summer, working conditions on the charging floor were almost unbearable. Silica refractories were of poor quality. Because of this, and the inadequate training of furnace men in fuel control and furnace operations, roofs, front and back walls, and ends burned out rapidly. Dolomite machines were unknown; consequently, furnace banks and hearths were fettled with dolomite by the use of hand shovels. The round system required six or more men. Each man took a shovelful of dolomite and, in his turn, deposited it on the back wall and bank by a dexterous forward swing and twist of the shovel. The upward swing of the shovel partially protected his face from the searing heat of the furnace coming out through the wide-open door. Considerable skill and stamina were required to do this job properly. Reverse valves, usually of the cast-iron butterfly type, were located below the charging floor. They were operated by long levers on the charging floor level men they became warped, because of heat and abuse, great strength and skill were required to reverse them. Furnace operations were difficult. The quality and quantity of producer gas coming from irregularly stoked, hand-operated gas producers was uncertain and unreliable. Furnace Linings and ports were quickly burned out. Poor bottom and side-wall refractories, indifferent and inexperienced crews, as well as irregular re-

Jan 1, 1961

By J. H. Yang, K. E. Gray

Results of single-blow bit-tooth impact tests on saturated rocks under elevated confining pressures and zero pore pressure were reported in a previous publication.1 This paper presents an extension of the earlier work to include a study of crater formation during tooth impact on both gas- and liquid-saturated Berea and Bandera sandstones at elevated confining and pore pressures. The basic data obtained were force-time, displacement-time, velocity-time and force-displacement curves during crater formation. Crater volume was also measured and the mode of crater formation determined. Bit tooth geometry, depth of penetration and velocity of impact were held constant. Results indicate that, with pore fluid present in the rock, failure trends from brittle to ductile as pore pressure is increased at constant confining pressure (pore pressure and borehole pressure were equal) For a given rock type, the mode of crater formation was dependent not only upon the nominal effective stress, but also upon the fluid which saturated the rock pore space. When confining pressure and pore pressure were equal (zero nominal effective stress), bit-tooth impact resulted in brittle failure for nitrogen-saturated Berea, and brittle to transitional failure for nitrogen-saturated Bandera; when saturated with liquid both rocks failed in a ductile manner at zero nominal effective stress. INTRODUCTION Dynamic wedge penetration tests have been conducted by investigators in several fields, but the failure mechanism of rock under dynamic stresses is not understood completely. The complex action of drilling bits, even considering the action of a single tooth, may be considered as a combination of drag bit and rolling cutter action. Thus, as a first step in understanding rock breakage in oil well drilling, single chisel impact and rock planing are of fundamental importance. For example, Gray 2 and Crisp3 studied drag bit cutting action at brittle stress states. Simon4 and Hartman5 studied the reaction of rocks to vertical impact by means of drop tests. The depth of penetration, crater volume and force-vs-time curves during crater formation were observed. The significance of indexing single-bit impacts has been noted.4,6-8 Gamer et al,9 reported impact tests on impermeable Leuders limestone at atmospheric and elevated confining pressures. In all cases the tests were accomplished on dry rock and pore pressure was considered to be zero. The importance of both confining pressure and pore pressure on the failure characteristics of rock was described. 10-12 It was found that the yield strength and ductility of porous rock depend on the state of stress under which the sample is tested. The importance of pore pressure on drilling rate in microbit experiments was noted by Cumingham and Eenink. l3 Robinson 12 also pointed out that in drilling the most important parameter in rock failure is the effective stress, where effective suess is defined as confining pressure pc minus pore pressure pp. The effect of pore pressure and confining pressure on rock strength was also noted by Serdengecti and Boozer 14 in strain rate tests, and by Gardner, Wyllie and Droschackl5 in elastic wave studies. Until recently all reported wedge impact studies under simulated wellbore stress states have been conducted on dry rock. Maurer 16 reported impact tests on samples saturated with deaerated water. Borehole and formation fluid pressures were equal in these tests except when mud was used in the borehole. With mud in the borehole and a high borehole-to-formation fluid pressure differential. Maurer observed "pseudoplastic" crater formation. Podio and Grayl reported impact tests on Berea and Bandera sandstone saturated with pore fluids having wide ranges in viscosities. In Podio and Gray's tests, confining pressure was elevated, but pore pressure and borehole pressure were held fixed at atmospheric pressure. The presence of

By Joseph Pogue

THE writer visited the Muzo emerald mines in July, 1915, and spent six days in their study. This paper embodies the results of his observations, plus information personally communicated by Robert Scheibe, FIG. 1.-SKETCH MAP SHOWING APPROXIMATE LOCATIONS OF ALL IMPORTANT EMERALD MINES AND PROSPECTS IN COLOMBIA. (Data in part supplied by Robert Scheibe, July, 1915.) Professor of Geology in the Mining Academy of Berlin, who at the time of the visit was completing a detailed field investigation of nearly a year's duration of the emerald deposits of Colombia. An elaborate account of this valuable work may be expected at a future date from the pen of Professor Scheibe.

Jan 5, 1916

By J. L. Ratliff, R. I. Jaffee, H. R. Ogden, D. J. Maykuth

An experimental program was carried out to improve the low-temperature ductjlity of tungsten through the combined use of dispersed oxides for grain-size control and Groups VII and VIII metal additions for matrix softening. Separate binary -alloy studies showed that increasing amounts of finely dispersed thoria or zirconia and critical amounts of rhenium, osmium, and iridium were effective in significantly reducing the ductile-to -brittle bend transition temperature of tungsten as well as in increasing its re crystallization temper - LIKE most of the high-melting point bcc metals, tungsten undergoes a marked transition from ductile to brittle behavior with decreasing temperatures. The material factors which influence the transition temperature include grain size, metal purity, and the presence of dispersed phases. ature and decreasing its recrystallized grain size. The beneficial effects shown by each of these additions on transition temperature and grain size in binary combinations appeared to be additive in tevnary combinations. Thus, combined additions of 2 to 8 vol pct thoria with 5 pct Re, 0.87 pct Os, or 0.30 pct Ir were effective in lowering the transition temperature of tungsten pom 2000 to 75"C, increasing its re crystallization temperature from 1600 to 1800°C, and decreasing its recrystallized gain size from 1175 to 6800 grains per sq mm. The mechanism by which these factors are operable in tungsten is not yet clearly understood. Nevertheless, it has become increasingly apparent that the interrelationship of grain size and matrix composition governs to a large extent the degree of low-temperature ductility which can be achieved. Though it is not possible to accurately assess the relative importance of these variables, the available evidence suggests that, at low temperatures, grain-size effects predominate over purity effects. This was indicated in recent studies by Allen, Maykuth, and Jaffee,' involving single crystals containing 20 to 40 ppm 0 and 1 to 30 ppm C. Thus, while each

Jan 1, 1964

By F. E. Jaumot, R. L. Smith

Self-diffusion in zinc has been used as an instrument for comparison of the absorption and sectioning techniques as a means of studying diffusion. Single crystal as well as poly-crystal samples were used asanda the temperature range of diffusion extended from 200° to 415°C. For temperatures above 200°C, the data indicate that the results obtained from the absorption technique agree with those obtained from the sectioning technique. The effect on the values of the diffusion coefficient of electroplating vs evaporation as a means of applying the tracer was investigated and no significant difference observed. It was found that an excess or deficiency of tracer did not materially affect the results obtained from the sectioning technique, but invariably caused errors with the absorption technique. NEARLY all self-diffusion experiments and many alloy diffusion experiments have employed radioisotopes as the instrument for following the diffusion. Of the various techniques in which radioisotopes are applicable, the two most widely used are the sectioning and absorption techniques. In the former, the diffusion coefficient is obtained from a curve of log concentration vs the square of the mean penetration depth. In the latter, the diffusion coefficient is calculated from a knowledge of the decrease in activity at the surface after diffusion. In spite of the importance of knowing the reliability of the diffusion data and the widespread use of these two techniques, they had not been directly compared experimentally on the same samples. Thus, such a comparison was worthwhile. The specific system chosen for this comparison was the self-diffusion of zinc, since the metal was readily obtainable in high purity, single crystals were easily grown, and the anisotropic features of the diffusion added an additional factor of interest to the comparison. Self-diffusion in both single and polycrystals was investigated, since the possibility existed that grain boundaries and grain boundary diffusion might produce different effects for the different techniques. Also, the effects of electroplating vs evaporation as a means of applying the radioactive tracer, and the effects of applying an excess or deficiency of tracer material were studied. The general experimental procedures and the mathematical analyses of both techniques have been described previously in some detail, and only those points essential to an understanding of the present work will be discussed here. The mathematical analysis of the sectioning data requires only a knowledge of the solution of Fick's equation. where C,, is the initial concentration, C is the concentration at depth x, D is the diffusion coefficient, and p is the absorption coefficient of the solvent metal for the radiation from the solute. Having obtained F from the experiment, the value of z can be read from a plot of F vs In z, and D can then be calculated if is known. The necessity of knowing the absorption coefficient causes most of the criticism of the absorption technique. It is very difficult to measure accurately under the conditions existing in the diffusion experiment, but it is absolutely necessary, as will be indicated briefly later. Portions of this problem have been discussed in detail elsewhere." The difficulties involved in the measurement of the absorption coefficient arise from three principle factors: the physical characteristics of the absorber, the geometry, and complex radiation spectra. The first two are heavily dependent upon the third. If

Jan 1, 1957

By Roscoe C. Clark

In a previous technical note' by Walter Rose, evidence is offered in support of the contention that "the possibility of describing oil recovery features in terms of capillary pressure phenomena has not been established entirely." It is not the purpose of this note to present further discussion of this possibility but rather to point out that the argument presented there does not appear to be generally valid. In the cited note' reference is made to the experiments of Welge2 wherein it was shown that when water was displaced by oil from a core the pressure in the water phase was less than in the oil phase but that when this oil was then produced by water drive the pressure in the water phase was greater than in the oil phase. Rose has concluded from these observations that conditions of static equilibrium did not obtain since the fluid saturations were such that phase discontinuities seemed unlikely. The argument from which this conclusion was drawn is based on the contention that "the pressure is always greatest in the non-wetting phase at each static interstitial interface of contact with the wetting phase." This premise appears to have been reached from a consideration of capillary phenomena in cylindrical tubes, although it may a1so hold for other types of pore geometry, hut as will be shown below it does not hold for all pore shapes and hence is not generally applicable. Since the pore structure of porous media such as reservoir rocks i- in general so complex as to defy exact description. it is undoubtedly of great value to establish a model in terms of pore shapes of known geometry, provided of course that the limitations of the model are recognized. That the limitations of the capillary. or cylindrical, tube model have not always been fully recognized will be evident from the following discussion of a pore of different shape hut one which may a. logically he considered a.; the capillary tube. The pore space to be considered is that shown in Fig. 1, which may be thought of as the "hole in a doughnut."* Consider the interface, A-B-A', between two immiscible fluids, P, and P2, which interface meets the solid alone a line, A-C.A'-C'. The interface A-B-A' is the surface of a spherical segmen† while the line of mutual contact be-

Jan 1, 1950

By T. S. Plaskett

A striated structure perpendicular to the growth axis was observed by the copper-decoration tech-nique in dislocation-free, .float-zoned silicon crystals. The striations, which were spaced about 100 p apart, fitted the relationship d = f/u , where d is the spacing, f is the growth rate, and u is the crystal rotation rate. Each stria was resolved into an UNDOPED silicon crystals pulled from quartz crucibles by the Czochralski technique usually exhibit a striated structure perpendicular to the growth axis.'-' This structure has been attributed to oxygen segregation, with the oxygen being introduced from the quartz crucible. If the crucible is rotated, the level of oxygen contamination has been reported as high as 10° atoms per cu cm.10 These striations are similar to solute striations commonly observed in doped Czochralski-grown crystals. The periodic nature of the striations is caused by a periodic variation in the growth rate",12 which is attributed mainly to thermal gradients in the melt.13 A finer striated structure14 attributed to constitutional supercooling is sometimes observed between the coarse striae. The oxygen striations have been observed by infrared transmission techniques,' by the copper-decoration technique,' by X-ray diffraction microscopy,6-8 and by 9 p absorption measurements3 on crystals pulled from the melt both with and without dislocations. In this investigation float-zoned dislocation-free crystals were examined by the copper-decoration technique. The level of oxygen for float-zone material is less than 1016 atoms per cu cm the lower limit of detection by 9 p absorption measurement. EXPERIMENTAL TECHNIQUE The crystals were grown by the float-zone process with the rf heating coil outside of the quartz envelope containing the silicon. All float zoning was done under an atmosphere of purified helium. The Dash technique15 was used to grow the crystal dislocation-free. This involves growing the crystal initially with a diameter between 2 and 3 mm and at array of starlike precipitates of copper. The strucLure was not .found at the surface tor a depth of about 1.5 mm, or in a region of similar width ahead of a dislocation network. The structure is postulated to consist of vacancy clusterings or dislocation loops. very rapid rates, about 20 mm per min, for a distance of about 3 cm. The diameter of the crystal is then increased to the diameter of the source of silicon, which in this case was about 19 mm. Because of the arrangement of the apparatus, the zone was passed downward rather than upward, contrary to the standard float-zoning practice. Also, the source was rotated rather than the seed. ziegler17 has made dislocation-free crystals by a similar technique but has passed the zone upwards. The starting material was zone-refined and had a p-type resistivity of 150 ohm-cm. The major impurity was boron; the total impurity excluding the boron was reported by the supplier (Dow-Corning) to be typically less than 2 x 1013 atoms per cu cm. The crystals were examined by the Dash copper-decoration technique18'19—a method in which about 10" atoms per cu cm of copper are diffused at a temperature between 900" and 1000°C into silicon which is then quenched to room temperature. On quenching, the copper precipitates on crystalline defects which are then visible when viewed by transmission infrared microscopy. The photomicrographs shown were taken either of the infrared image tube screen or directly on infrared film. All sections prior to decorating were chemically polished and, for some sections, given a sirtlZ0 dislocation etch-pit examination. After decorating, the samples were mechanically polished. RESULTS A photomicrograph, taken in transmission of a decorated cross section, is shown in Fig. 1. The portion of the section shown is near the surface of the crystal. The entire cross section showed no dislocation etch pits after being given a Sirtl etch treatment. It is seen that the copper precipitated randomly. Each precipitate, as has been reported by others, was found to have a starlike structure.

Jan 1, 1965

By Walter V. Knopp, Laurence Delisle

The aim of this work was the preparation of nickel-steels from elemental metal powders by powder metallurgy techniques. It was known that plain carbon steels could be made from a mixtufe of iron powder and graphite and that the effect of carbon on iron in powder form was of the same nature as that produced in fusion metallurgy. The problem in making nickel steels from elemental powders consisted therefore in finding out whether sufficient diffusion of the nickel and other incidental metals . normally present in such steels could be induced in the solid state to modify the properties of plain carbon steels made from powders and produce the beneficial effect of alloying. The composition selected originally was that of an S.A.E. 2330 steel. Metal powders, in the proportion correspending to that composition, were mixed with graphite, pressed, and heated at different temperatures for different periods of time, to produce bonding of the metal particles and mutual diffusion of the various elements without melting. Temperatures up to 1325°C and sintering periods as long as 6 hr were first investigated because it was expected.that such conditions would produce maximum diffusion with an accompanying improvement in the properties of the alloy. It was found that, although diffusion proceeded to a large extent under the conditions investigated, it would not be complete unless sintering were carried out at a high temperature for much longer than 6 hr. Relatively high temperatures and long sintering times are objectionable from a practical point of view, particularly when a low COSt material is to be produced, because they necessitate the use of special, costly equipment. Work could be done to improve the diffusion of iron and nickel by changing conditions other than the sintering temperature and time, that is, finer primary or alloy powders could be used. However, a marked change in the properties of the steel had been observed even with only partial diffusion. It was thought, therefore, that instead of trying to improve the diffusion, advantage might be taken of its incompleteness to produce a special structure consisting, in the unquenched condition, of a hard constituent, rich in nickel, dispersed in a tough pearlitic matrix. Steels with such a structure, not readily obtainable by fusion, should have desirable mechanical properties. Besides, it should be possible to prepare them from elemelltal powders under economical conditions. This latter alternative was therefore adopted for the second phase of this work. This report is divided into four parts: I. General Procedure. 2. Effect of Sintering Temperature. 3. Effect of Varying the Nickel Content. 4. Effect of Alloying Elements. General Procedure The general technique of cold pressing as used in powder metallurgy was applied.

Jan 1, 1949

By J. R. Thompson

It is common practice, and certainly good business as all of us know, to take care of plant operating equipment. Machinery of any type requires periodic inspection and planned maintenance. With this thought in mind a plant operator should at the end of every shutdown period make regular belt inspections and plan for later appropriate care and maintenance. The points mentioned below are understood well by all of us but are sometimes forgotten because belt conveyors are comparatively easy to operate. Maintenance of any conveyor belt is dependent upon the fundamental characteristics of the two component parts-cover and carcass.

Jan 6, 1950