Search Documents

Rougher Cells The photo shows one of three carloads of new Denver Equipment Co. rougher flotation machines destined for a single customer. [ ] Low level froth overflow on both sides, and double impeller mechanisms in an open-flow type tank, were designed to enable control of variable conditions in the rougher circuit for better metallurgy. Intense agitation and aeration are claimed, for effective recovery of low-grade mineral particles. Standard parts are used, interchangeable with regular Denver Sub-A units. The Super Rougher is now in production and a 2-cell No. 24 machine will be displayed at the Mining Show. Circle No. 1 Fans A line of industrial fans built for air or materials handling is available in eleven sizes from 670 to 44,000 cfm capacity from Westinghouse Electric Corp. The air hand¬ling wheel has backwardly-inclined blades. Circle No. 2 Trolleyphones The Femco Trolleyphone, plug-in model, 2550 series, is offered as a simple mine or mill communications system by Farmers Engineering & Mfg. Co. More compact, easier to install and service, the new model is powered from existing trolley wire or power line. Circle No. 3

Jan 1, 1952

Transit A light weight, totally enclosed theodolite, especially designed for mining, has been placed on the market by Askania Werke, A. G. The instrument weighs only 41/4 lb and measures 51/8 x 71/2 in. without tripod and in a waterproof aluminum hood. It may be mounted on tripod or bracket without removing the protective hood. [ ] Standard equipment includes diagonal eyepiece rotating in all directions which eliminates need to be in line with scope for sighting and makes an auxiliary scope unnecessary for steep sights. The transit reads direct to 1 minute and may be estimated to 6 seconds by means of optical micrometer on both horizontal and vertical circles. The telescope in vertical position serves as optical plummet, sighting through an opening in the base. The instrument is shown above mounted for attaching to a pin driven in timber or rock, eliminating tripod or set-up bar in cramped quarters. The chain clamp in the lower picture is used on timber or steel ground supports. Complete with carrying case and set-up brackets, ready for use in a raise, it weighs less than 6 lb, and the protective hood remains on until the instrument is securely mounted. [ ] Accessories for increasing versatility of this mining theodolite are: tripod, electric illumination for optical micrometer and reticule, close range objective lens, and objective lens prism for sighting vertically in front of the instrument. Circle No. 1

Jan 1, 1952

Dump Truck Kenworth Motor Truck Corp. is beginning full scale production of its new heavy-duty, end-dump earth mover, model 801, a truck engineered for earth moving under the most adverse operating conditions. Payload capacity of the Kenworth earthmover is 30,000 lb and it is over-tired for safety, flotation and high tire life. The truck's body capacity, struck measure, is 9.9 cu yd, with heaped [ ] load at 11.9 cu yd. The earth-mover has a full anti-friction bearing mounted, power assisted steering gear, simplified controls, minimum turning radius and wide axle track to insure ease of handling, maximum maneuverability and high stability. The offset cab of the Kenworth visibility for the driver, before and after. Circle No. 1 Safety Equipment A compact, safe, and efficient valve assembly approved by the United States Bureau of Mines for use with MSA air line respirators, abrasive masks, and abrasive helmets has been developed by Mine Safety Appliances Co. The new MSA continuous air flow control valve regulates air flow from a compressed air source to an operator using respiratory protective air line equipment. Three parts-a centridge container, a cartridge and the air flow check valve-comprise the entire assembly of the control valve. A position action adjustment knob on the cartridge container regulates the amount of air flowing to the operator. The valve can be detached from the air line instantly by pressing the trigger on the cartridge container near the check valve. As the trigger detaches the hose, the spring loaded ball-type valve, which is attached to the end of the hose, automatically stops the flow of air. Circle No. 2

Jan 1, 1952

By L. E. Mannion

Sodium carbonate (soda ash) is one of two principal commercial alkalis. Its principal competitor is sodium hydroxide. The use of sodium carbonate is recorded in ancient Egypt, where naturally occurring brines and solid salts provided impure soda for early glassmaking. Until the 19th century, soda ash (as well as potash) was recovered mainly by leaching wood or other plant ashes. In 18th-century Europe, for example, leaching seaweed ash with hot water produced a brown laundry lye. One of the better grades of this material was a Spanish product, barilla, which analyzed 24 to 30% Na2CO3 (Hou, 1942). The modern chemical industry was born in 1691 with the LeBlanc process for making sodium carbonate from salt, sulfuric acid, and lime. English industry used this process extensively in the 17th and 18th centuries. The next major advance was in 1863, when Ernst Solvay devised the ammonia-soda, or Solvay process. The first of many Solvay plants was built in 1874. These supplanted the LeBlanc method and dominated worldwide soda ash production until 1974, when mined sodium carbonate became predominant. Although considerably less important until recently, natural sodium carbonate deposits historically have supported small soda ash operations throughout the world. Shortages during World War II stimulated production of "natural" soda ash from such deposits, particularly at Searles Lake, CA and Lake Magadi, Kenya. More spectacularly, increased production from the vast trona deposits in Wyoming has virtually supplanted the Solvay process in the US. Principal producers of natural soda ash as well as the character of the source deposits are listed in Table 1. [ ]

Jan 1, 1983

By Stanley F. French, Bruno F. Koch

Although the amount of dust that will be actually recovered in the six main dust-control systems cannot be accurately stated until the tests mentioned previously are carried out, it is estimated that the average air entering the wet collectors will contain around 5 grains of dust particles per cubic foot. This means that the six systems handling a total of about 133,000 cu.ft. of air per minute will return about 68 1/2 tons of dust to the concentrator per day and since the copper in this dust will average around 2 per cent, the total recovery is approximately 1.37 tons of copper every 24 hours. This important copper recovery is not due entirely to the dust-control system since in a plant without control only the duct that is dispersed to the atmosphere represents a loss. A conservative estimate of the recovery of copper solely due to the dust control system would be about half of the total or approximately 0.70 tons of copper per day.

Jan 1, 1942

By J. G. Baragwanath

CUBA'S lateritic iron ores, occurring on the northern coast of that island, though known to the Spaniards. did not receive any general attention until the close of the Spanish-American War. Preliminary studies of these deposits at that time indicated that the limonite contained small percentages of nickel and chrome, and it ryas subsequently discovered that although the average nickel content was only approximately 0.6 per certain limited areas of ore were suffiniently high in nickel to be considered commercial provided a suitable process fur its recovery could be developed. Early in 1937, Pardners Mines Corp. began a series of investigations which led to the development of such a process. Coincidentally, this company acquired option' on certain properties in the Levisa Bay and Moa Bay regions and conducted a systematic campaign of exploration by test pits and hand-auger holes in the course of which an aggregate of 90.000.000 tons of ore was developed in eight deposits.

Jan 1, 1945

By Charles P. Berkey, Joseph H. Sinclair

This paper describes the results of a visit to the Santa Elena Peninsula, Ecuador, in January and February, 1921. On account of the complicated folding and faulting of the rocks and the peculiar occurrence of petroleum, field work was possible on only a few of the many geological problems and the results here published are only a contribution to the solution of the general problem. We know of nothing published on the geology of the district, except one account, in Spanish and German, by Theodor Wolf. The Santa Elena peninsula, the most important headland of the coast of Ecuador, lies two degrees south of the equator. The chief town, Santa Elena, is about 75 miles west of Guayaquil, the main seaport of Ecuador. The nearest developed oil field is the Zorritos of northern Peru, 120 miles south across the Gulf of Guayaquil. If newspaper reports are true, viz. that the Anglo-Ecuadorian Oilfields, Ltd., has recently brought in a 700-bbl. well on the coast of the peninsula near Ancon, the district may become important in the production of petroleum. At the time of our visit, the best way to reach the peninsula was by a steamer of the Pacific Steam Navigation Go., southward from Panama and northward from Guayaquil. About once a week, one of these steamers anchored 1/2 mile off shore near the village of Salinas, an important cable station. An alternative route, in the dry season, is by automobile from Guayaquil. In February, 1921, a railway bed had been graded part way between Guayaquil and Salinas, but this was detcriorating rapidly because of lack of funds to continue construction or to keep in repair that portion already completed.

Jan 1, 1923

By Charles P. Berkey, Joseph H. Sinclair

This paper describes the results of a visit to the Santa Elena Peninsula, Ecuador, in January and February, 1921. On account of the complicated folding and faulting of the rocks and the peculiar occurrence of petroleum, field work was possible on only a few of the many geological problems and the results here published are only a contribution to the solution of the general problem. We know of nothing published on the geology of the district, except one account, in Spanish and German, by Theodor Wolf. The Santa Elena peninsula, the most important headland of the coast of Ecuador, lies two degrees south of the equator. The chief town, Santa Elena, is about 75 miles west of Guayaquil, the main seaport of Ecuador. The nearest developed oil field is the Zorritos of northern Peru, 120 miles south across the Gulf of Guayaquil. If newspaper reports are true, viz. that the Anglo-Ecuadorian Oilfields, Ltd., has recently brought in a 700-bbl. well on the coast of the peninsula near Ancon, the district may become important in the production of petroleum. At the time of our visit, the best way to reach the peninsula was by a steamer of the Pacific Steam Navigation Go., southward from Panama and northward from Guayaquil. About once a week, one of these steamers anchored 1/2 mile off shore near the village of Salinas, an important cable station. An alternative route, in the dry season, is by automobile from Guayaquil. In February, 1921, a railway bed had been graded part way between Guayaquil and Salinas, but this was detcriorating rapidly because of lack of funds to continue construction or to keep in repair that portion already completed.

Jan 1, 1923

By J. L. Lamont, W. Crafts

Studies of the effect of composition of steel on hardenability by Grossmann,' and as-quenched hardness by Field2 and by the authors, have made it possible to predict the results of quenching when the composition and cooling rate are known In order to extend the application of the hardenability calculation to the quenched and tempered condition in which steel is finally used, a survey has been made of the hardness changes caused by tempering. From this study a method has been developed for the prediction of hardness and tensile strength of steel in the tempered condition. The method of calculation was developed from Rockwell C hardness tests on quenched and tempered Jominy specimens and is expressed in Rockwell C hardness units. It is of an additive type in which the degree of softening from as-quenched hardness is estimated. Tem-pred properties may be calculated within about plus or minus 5 Rockwell C hardness or plus or minus 15,000 lb. per sq, in. tensile strength. This degree of accuracy is less than that necessary for the control of heat-treatment, but is adequate for the comparative evaluation and selection of alloy steels. The formula indicates that tempered hardness is primarily dependent on as-quenched hardness and, as in the hardening reaction, the progress of tempering is controlled mainly by the carbon content. Alloys tend to retard softening by a secondary hardening mechanism in which the alloy appears to migrate from ferrite to the carbide phase. The factors for the effects of alloys in tempering vary so much from the effects of alloys in hardening that different steels of equivalent hardenability may, after like heat-treatment, differ considerably in tensile strength. Procedure In developing the method for calculating tempered Rockwell C hardness, simple and complex steels were tested over a range from 0.08 to 0'65 per cent carbon and up to 2.68 per cent manganese, 2.18 silicon, 3.50 chromium, 4.94 nickel, and 1.06 molybdenum. The steels were made as small induction-furnace heats at the Union Carbide and Carbon Research Laboratories, Inc' The accuracy of the method was finally checked on a variety of carbon, low-alloy and high-alloy types of heat-treating steels produced under commercial conditions. The method was based on a study of tempered Jominy bars, and its validity was tested by correlation with the center hardness and tensile strength of oil-quenched and tempered bars from 1/2 to 4 in. in diameter. The method of calculation was derived from the differences in Rockwell C hardness between as-quenched and quenched and tempered Jominy specimens. Prenormalized Jominy hardenability speci-menS quenched from a normal temperature for austenitizatios were used to obtain a range of as-quenched Rockwell C

Jan 1, 1948

By W. Crafts, J. L. Lamont

Studies of the effect of composition of steel on hardenability by Grossmann,' and as-quenched hardness by Field2 and by the authors, have made it possible to predict the results of quenching when the composition and cooling rate are known In order to extend the application of the hardenability calculation to the quenched and tempered condition in which steel is finally used, a survey has been made of the hardness changes caused by tempering. From this study a method has been developed for the prediction of hardness and tensile strength of steel in the tempered condition. The method of calculation was developed from Rockwell C hardness tests on quenched and tempered Jominy specimens and is expressed in Rockwell C hardness units. It is of an additive type in which the degree of softening from as-quenched hardness is estimated. Tem-pred properties may be calculated within about plus or minus 5 Rockwell C hardness or plus or minus 15,000 lb. per sq, in. tensile strength. This degree of accuracy is less than that necessary for the control of heat-treatment, but is adequate for the comparative evaluation and selection of alloy steels. The formula indicates that tempered hardness is primarily dependent on as-quenched hardness and, as in the hardening reaction, the progress of tempering is controlled mainly by the carbon content. Alloys tend to retard softening by a secondary hardening mechanism in which the alloy appears to migrate from ferrite to the carbide phase. The factors for the effects of alloys in tempering vary so much from the effects of alloys in hardening that different steels of equivalent hardenability may, after like heat-treatment, differ considerably in tensile strength. Procedure In developing the method for calculating tempered Rockwell C hardness, simple and complex steels were tested over a range from 0.08 to 0'65 per cent carbon and up to 2.68 per cent manganese, 2.18 silicon, 3.50 chromium, 4.94 nickel, and 1.06 molybdenum. The steels were made as small induction-furnace heats at the Union Carbide and Carbon Research Laboratories, Inc' The accuracy of the method was finally checked on a variety of carbon, low-alloy and high-alloy types of heat-treating steels produced under commercial conditions. The method was based on a study of tempered Jominy bars, and its validity was tested by correlation with the center hardness and tensile strength of oil-quenched and tempered bars from 1/2 to 4 in. in diameter. The method of calculation was derived from the differences in Rockwell C hardness between as-quenched and quenched and tempered Jominy specimens. Prenormalized Jominy hardenability speci-menS quenched from a normal temperature for austenitizatios were used to obtain a range of as-quenched Rockwell C

Jan 1, 1948

A 2-year moratorium on accreditation of curricula bearing new designations has been declared by Engineers' Council for Professional Development at its Executive Committee meeting on July 29, 1952. Reason: a more definitive description of what the contents of a curriculum should include to be appropriately designated as "engineering" is needed. This action was brought on by the Committee of Evaluation of the American Society of Engineering Education which had become perturbed over the extension of the name "engineering" to numerous fringe curricula. The 2-year period will permit time for the Committee on Evaluation to study the question and make a recommendation for further action by ECPD. ECPD action also provided that the following curricula should only be given provisional accreditation for one year upon either inspection or reinspection; such provisional accreditation to be extended annually for not more than two successive years pending the report: Engineering Physics, Engineering Mechanics, Geological Engineering, Geophysical Engineering, and Textile Engineering. There are 22 such curricula now accredited.

Jan 1, 1952

By St. John, JOHN Ancel

AT THE New York meeting of the Institute of Metals Division in February, 1927, Jeffries and Tarasov presented a paper on Tungsten and Thoria,1 in which the experimental facts were interpreted in accordance with the prevailing point of view that the thorium is present as the oxide, thoria. In discussing that paper the writer of this article stated that his own investigations, which had been unavailable to Messrs. Jeffries and Tarasov, showed that the so-called "thoriated" tungsten filament failed to disclose any sign of the oxide when subjected to X-ray diffraction analysis, but did give plenty of evidence of the presence of metallic thorium and, in certain cases, of a material believed to bean alloy of tungsten in thorium. Since these results were completely at variance with the results reported in the paper under discussion and with other papers which had preceded it from time to time in the past, it was felt that further discussion should be withheld until the new evidence could be presented adequately. Arrangements were therefore made to present that evidence at this meeting. MATERIAL EXAMINED The material examined was high-emission filament such as is used in radio tubes, supposed to contain about 0.75 per cent. thoria. The actual analysis was not stated.

Jan 1, 1927

Jan 3, 1976

By P. D. Frost, H. A. Robinson, J. R. Doig, M. W. Mote

The mechanism of hardening in heat-treatable zirconium alloys was foUNd to be analogous to that for titanium alloys. Zirconium containing a relatively large addition of a ß -stabilizing element such as molybdenum or columbium can be hardened by the following transformation: Lean alloys, having insufficient alloy content to retain ß at room temperature are hardened by the following transformation: Application of these findings in Zr-Mo-Sn and Zr-Nb-Sn alloys produced strengths as high as 190,000 psi with reasonable ductility. PRIOR research on zirconium alloys has been concerned with development of greater strengths and creep resistance by solid-solution hardening or by dispersion hardening. Although solution and aging heat treatments had been applied earlier to zirconium alloys, quenching frequently produced low ductility. The possibility that the ß-to-w transformation, discovered earlier in titanium alloys,' might also occur in zirconium alloys and cause low ductility was considered, and, indeed, was found as predicted2 to be the case. In the earliest experiments, the heat-treatment response of titanium, too, was disappointing. However, by avoiding the formation of the embrittling w phase, it became practical to obtain room-temperature strengths higher than 180,000 psi, with elongation values of 10 pct.3 Based on the present concept of titanium heat treatment, the principal requirement for a heat-treatable zirconium alloy is that it contains a certain minimum amount of one or more ß -stabilizing elements. Only molybdenum, columbium, and tantalum, when present in sufficient amounts, are known to stabilize ß zirconium to room temperature during rapid cooling from the ß field. Tantalum was undesirable because of its high thermal-neutron cross section. Aluminum and tin are effective a stabilizers, but aluminum has been shown to seriously decrease the corrosion resistance of simple zirconium alloys in hot water. Therefore, for the present study, tin was used as the stabilizer addition. The alloys selected for this evaluation are presented in Table 1 along with their analyses and ß-transus temperatures. The analyses indicated that intended compositions were usually realized. EXPERIMENTAL PROCEDURES All of the alloys were melted from sponge zirconium and fabricated to sheet for heat treatment

Jan 1, 1960

By AIME AIME

BLANDFORD. C. BURGESS, the new Chairman of the Industrial Minerals Division, took the advice of Horace Greeley in reverse-he turned his hack on San Francisco and the Golden Gate, and after a few side excursions toward Alaska and Arizona, hit the trail eastward, not for the lonesome pine, but for Spruce Pine, N. C. Born Aug. 10, 1893, in San Francisco. Burgess found his first job, shortly after finishing high school at 19, as axeman for a surveying party of engineers working for the Southern Pacific Co. in Oregon. Later he moved on up with them into Alaska. He liked the engineering profession, and decided to equip himself further so he entered the University of California in the fall of 1913. and for the next two years devoted himself to acquiring an education in civil engineering.

Jan 1, 1945

Steel Tape The new Lufkin Royal Ni-Clad steel tape, made in 25, 50, 75, and 100-ft sizes, is stated to cost less than any other steel tape on the market. Figures and graduations are an integral part of the steel and the nickel plated surface is rust and corrosion resistant. Circle No. 1 Lift A manually operated and propelled hydraulic lift marketed by Century Products Co. weighs only [ ] 150 lb, but the 23x24 in. platform will raise 1000 lb from floor level to 4 ft height. Circle No. 2 Scintillation Counter The Scintillator from Precision Radiation Instruments, stated to have 100 times the sensitivity of the Geiger counter, is suitable for prospecting and may be operated from plane or moving vehicle. The instrument is contained in a 2-lb probe and the belt mounted battery box weighs less than 4 lb. Circle No. 3 Generators Wincharger Corp. announces development of a Speedy-Shift wheel-barrow base type attachment for model 700, 1800 and 5000 engine-generator sets. Portability of the engine-generator sets themselves has been improved by belted construction for higher operating speed and maximum weight reduction. Circle No. 4

Jan 1, 1952

Scraper With over 40 pet more struck capacity than previous models, the new Caterpillar No. 90 scraper is designed to increase earthmoving production when used with D8 tractor power. This scraper moves dirt with the aid of a hard surfaced, reversible cutting edge. Material is carried in a flat, doublebottom bowl of high tensile steel. Operation is by means [ ] of a cable-control unit, which can be mounted on the rear of the tractor to provide for positive loading and ejection. Tapered roller bearings are installed at each axle. The scraper uses two 24.00 to 29 front tires and two 27.00 to 33 rear tires, all four of 24-ply rating. When loaded, the scraper distributes 60 pet of the weight on the rear tires. Circle No. 1

Jan 1, 1952

By Hugh Neill, O&apos

In previous papers,' the author has reported the results of experiments on the straining in tension of a single-crystal test piece, about 0.6 in. long, of vacuum-melted electrolytic iron containing 1.8 per cent. of silicon. The crystal was originally in the "as cast" condition, and was stressed slowly along a tetragonal axis so that slipping along conjugate gliding planes finally transformed the original cylindrical portion into a pair of fracture wedges. One of these fracture wedges was sectioned along the stress axis in a plane at right angles to the edge of the wedge. A metallographic study of this plane of section led to the conclusion that slip had taken place in the (111) direction along (112) planes making a V shape with the stress axis. The present paper describes the results of scratch-hardness tests conducted on the same section, in order to determine the distribution of strain hardness therein, followed by annealing, and considers the resulting variations in hardness. These observations supplement those made by Krivobok2 on similar material reduced 25 per cent. by hammering (i. e., by impact) in the cold. In order to investigate ageing effects, two small crystals of the same alloy were also tested. The Specimens Employed The principal specimen, A, was prepared for the metallographic examination leading to the determination of the slip planes of the crystal. Therefore the work described in this paper was conducted on metal which had been repeatedly etched and had been allowed to rest for about 30 months after straining. It consisted of a section of the fracture wedge and contiguous unstrained head of the test piece taken along a tetragonal axis parallel to the direction of stressing, the plane of section originally being not far removed from the (011). Several subsequent grindings

By Ian Wark

IT has been shown1 that in the absence of heavy metal salts, the nature of the alkali used to promote differential flotation-whether caustic soda, lime or sodium carbonate-is unimportant. The hydroxyl ion is the active depressant upon which differentiation depends, and the pH value determines whether a film of collector forms on any given mineral surface. Even when sodium cyanide is used in conjunction with alkalies, it is the pH value and not the nature of the alkali or its concentration that is important, for upon the pH value alone depends the fraction of the added sodium cyanide that is present as cyanide ion, which is the true depressant. When heavy metal salts become dissolved from partly oxidized ores, or are added intentionally as activators, conditions are different, and metallurgists have found that lime and sodium carbonate do not give identical results, even when added in amounts sufficient to produce the same pH value. In the few instances in which we had attempted to confirm this view, we had failed to do so, for, with nothing to guide us, we had inadvertently chosen solutions that gave contact curves of a "stand-ard type," which correspond to conditions of ready floatability. Now, however, we find that, in the presence of copper salts, and within a restricted range of reagent concentrations, the nature of the anions present is important, and that sodium carbonate does influence the results, apart from the usual effect due to its influence on pH value. With the recognition of this anion effect, and with the control of temperature already introduced,' it appears that the factors of major importance in connection with this set of reagents have been taken into consideration, and that the results obtained and the conclusions drawn from contact tests will be of more immediate value to the operator.

Jan 1, 1939

By H. E. McKinstry

Movement on a fracture of irregular shape can cause local widening of the fissure and thereby offer freer channelways for circulation of ore-depositing solutions. This influence: coupled with large areas of wall rock available for reacting with ore solutions in brecciated and shattered ground can account for locally active deposition of metals and the resulting ore shoots. Such irregularities in the fracture system may be caused by local variations in the strength of rocks and by pre-existing lines of weakness, especially if these stand at favorable angles to certain components of the fracturing stress. Therefore correct interpretation of the mechanics of fracturing should permit deductions as to structurally favorable places on unexplored portions of the vein system. Introduction It has long been recognized that movement on a curved or irregular fault surface is capable of separating the walls in certain portions of the fault, but until very recent years the importance of this mechanism as a factor in localizing ore shoots has escaped proper recognition. A short time ago W. H. Newhouse' presented a careful analytical study of displacements and their corresponding open spaces. For reasons that will be discussed later, it frequently happens that portions of the vein which are favorably oriented are not merely wider but also richer than the average. In many cases the widening with its accompanying richness coincides with very minor changes in the dip or strike of the vein, irregularities that commonly escape notice unless the vein is mapped in detail and a careful geometrical analysis made. While the relationship between the width of the vein and the changes in dip or strike has been recognized as a matter of observation, the irregularities have been accepted as more or less the result of accident. There has been very little effort except in isolated cases to find out the causes of these changes in dip or strike. Yet it is clear that if the causes can be recognized and expressed in terms of geologic structure the geologist will know where to look for repetitions of these favorable conditions either on extensions of the same vein or on adjoining veins. Any lack of understanding of the causes is due to the limitations of our ability to interpret our observations and not to the sheer capriciousness of

Jan 1, 1941