Search Documents

By Ayman Tawadrous

Cave mining offers a flexible technique to exploit large, low grade, deep ore bodies with low operating costs. It is typically done in either a top down approach; i.e. sublevel caving, or in a bottom up approach; i.e. block or panel caving, to extract ore bodies that may have been previously considered unfeasible to mine. Sublevel Cave (SLC) mining, in particular, is a cave mining method based upon the utilization of gravity of blasted ore while the overlying host rock fractures and caves under induced stresses and gravity. Thereby the caved waste originating from the overlying rock mass fills the temporary void created by ore extraction to achieve a controlled collapse of the roof.

Jan 1, 2015

By P. R. Mohanty, Kaushik Dey

Blast-induced tunnel overbreak prediction in the past has been based on peak particle velocity measured far from the blast site with necessary extrapolation. This has often resulted in suggesting higher damage threshold levels of Acceleration/PPV for overbreak prediction (Bogdanhoff, 1995, Holmberg and Persson, 1997, Murthy and Dey, 2002). These, site-specific far-field blast vibration studies, have also revealed that predicted PPV levels for overbreak could lie in the range of 700-5000 mm/s, an extremely wide range to generalize. Experimental blasts were conducted, in an underground metal mine located in eastern India, with an objective to study the level of acceleration /peak particle velocity generated in tunnel blasting. Accelerometers and tri-axial geophones with measuring ranges upto 500 g, 254 mm/s respectively, were mounted on the tunnel floor close to the blast face, with sensor distances varying from 15.25m to 36.10m. Due to straight faces the measuring distance could not be reduced further anticipating, in particular, cable damage. The equipment used was of M/s Instantel Inc., Canada. The blast pattern used was burn cut with large dia relief holes providing the required free face. The blast hole depth was 1.8m. Tunnel overbreak was measured using a telescopic offset rod fabricated at Indian School of Mines, Dhanbad, India.

Jan 1, 2004

By Steve Brace

Electronic detonators have been commercially available to the mining industry worldwide for over ten years. It is estimated that total cumulative global sales will have reached 25 million units by the time of the Conference in February 2004. This is below 0.2% of all detonator types sold during this period. Perhaps 20 million will have been used underground in South African gold, diamond and platinum mines. These will have been produced by South African companies, in South Africa for South African customers. Here efforts have met with greater success and in 2003 fully 5 million, or 3% of local detonators sold, could be of an electronic type. However, it is estimated that about US$7.00 (R50.00) has been expended on R & D, manufacturing facilities and marketing, for each unit so far sold. Large sums of money continue to be spent. Despite the apparent success in South Africa, is it justified? Electronic initiation systems have not produced significant technical benefits to the end-user underground nor corporate profits to the supplier. Some doubt they ever will (even from the large surface operations where the price per unit is much higher). A conclusion might be that they have failed. In 1998 Smit and Pistorius wrote a paper titled “Implications of the Dominant Design in Electronic Initiation Systems in the South African Mining Industry”. This ISEE paper seeks to summarise and review the conclusions of the earlier work. These were: that a dominant design had not yet emerged; the type of connector and the way in which detonators are connected and programmed would be a strong determinant influencing the development of a “winning” product; technical aspects rarely solely determine which becomes the dominant design (marketing, social and economic factors often have a strong influence); electronic initiation systems were an emerging technology for the underground gold mining industry in South Africa and because it was under severe cost pressure the mines would look to them to raise productivity and hence profits; finally, as a dominant design begins to emerge, one could expect a number of players to exit from the industry.

Jan 1, 2004

By Frederick Kuhnow

In open pit blasting, energy is released and transmitted through the geology. Negative effects can impact operations and can affect mine production. This paper presents recommendations for blast design to prevent damage due to ground motion from blasting on adjacent concrete structures of underground operations. It includes a case study describing a problem regarding an open pit mine expansion and asks whether production blasting will damage concrete shaft structures due to blast stress waves and blast-induced ground motion.

Jan 1, 2014

By Erkan Bayrak, Serkan Erkara, Ozkan Duzgun, Ekin Gungor

This paper presents part of the outcomes of the drill and blast optimization project carried out at Kisladag Gold Mine in Turkey. Kisladag Gold Mine is the largest gold mine in Turkey with a low-grade, bulk-tonnage, open pit operation that uses heap leaching for gold recovery. After blasting, the ore is fed to a three-stage crushing circuit which prepares crushed ore approximately -10 mm (0.39 in) for heap leaching. Crusher downtime analysis showed that blocky material and insufficient feed are causing significant downtimes with the primary crusher. This was supported by the fragmentation data collected to date. It was decided to initiate a fragmentation project to understand the variation in the run-of-mine (ROM) size with a view to provide a consistent feed to the crushing circuit. The study includes the analyses of the ore strength and structure, image analysis of the fragmentation pictures acquired from blasts, blast auditing and quality assurance and quality control (QA/QC) analyses. During this project, over 200 fragmentation pictures were acquired from 47 blasts to optimize ore and waste blasts. Ore strength varies between 30 and 120 MPa and rock quality designation (RQD) ranges between 30 and 100. A site-specific fragmentation model was used to calibrate the fragmentation for blast domains formed. In addition, alternative cases were simulated to achieve blasts designs with consistent ROM fragmentation size distribution. Alternative blast designs that include stemming length and powder factor changes were suggested. Long stemming length, drill cuttings use, free faced blasts, small shot sizes and poor stemming length control were some of the key issues causing coarse fragmentation.

Jan 1, 2015

Drilling through unconsolidated material I need to drill blastholes through a mix of consolidated and unconsolidated material. This material is hung up in an underground ore pass. The total length of the holes would be approximately 200 feet. We have attempted to drill through the material with conventional ITH drilling, but were unsuccessful. Does anyone have a suggestion? I am more than willing to bring in a contractor to do the job, if they have solid experience with this type of problem.

Jan 1, 2011

By Jeff Dean

As the Society celebrates its 35th year as an explosives industry association, it is clear that we are part of an industry that covers many sectors of economic activity. We are the voice of those who use, transport, store, manufacture, and dispose of commercial explosives products and others that serve the end user of explosives products. Along with other associations in this industry, we have a combined membership of hundreds of companies and tens of thousands of individuals in the U.S. and around the globe.

Jan 1, 2010

By Benjamin Cebrian

Metallurgical testing at Cobre Las Cruces prior to production at the mill was done with overburden gossan. Some of that test gossan was a very fine material, wet by the water conditions at the bottom of the pit. When processed and stored wet at the fines material 3000 tonne (3307 tons) silo, this material cemented in a very unusual manner.

Jan 1, 2010

By Edward P. O'Hern

The importance of the so-called explosives and the increasing extent of their use are evident from the fact that the production in the United States for the year 1910, as shown by the United States Census reports, amounted to the enormous total of approximately 480,000,000 pounds, this being more than double the production of 1905 and more than three and one-half times that of 1900

Jan 1, 2015

By Robert Hopler

THE KEYSTONE NATIONAL POWDER COMPANY is an Independent organization, incorporated under the laws of the State of Pennsylvania. It has three dynamite mills near Emporium, Pa., with a daily capacity of 165,000 pounds. It maintains branch offices in practically all the largest cities east of the Rocky Mountains, and has distributing magazines located in every section where there is a demand for high explosives, with facilities for wagon deliveries. Our mills are all of modern type and are equipped with the most improved machinery for the manufacture of high explosives. The efficiency of our laboratory in conjunction with the high class of labor employed, has enabled us to put on the market an explosive, the quality of which is the result of extensive research and scientific knowledge. Our modern and complete equipment for harbor and railroad transportation insures our patrons of prompt deliveries, which is an essential feature particularly to contractors and those whose facilities for storage are limited.

Jan 1, 2013

By Robert Hopler

True there is a certain proportion of nitro-glycerin in dynamite cartridges, but the dangerous explosive is scientifically compounded with wood pulp and some other ingredients in such a way that it can be absolutely depended upon not to explode accidentally if our simple and plain instructions for its use are complied with.

Jan 1, 2012

By Benjamin Cebrian

Rock blasting at quarries represents multiple challenges not easy to see at first sight. Aggregate industries face similar or superior prices for explosives while extracting a material that usually is of less value of metal mining operations. Therefore, learning to optimize a quarry operation can be a perfect training for a position in blasting at larger metal mining operations.

Jan 1, 2010

By Ery Wardhana, Stefanus Jagad, Relinda Sanistya, Hasucita Tausi, Rido Situmorang

The blasting process is one of the most high-risk activities in mining operations. Shotfirers and blasting crews face hazards from slope failure, toxic gas and fumes, or unstable ground condition every day of the blast. But on the other hand, to ensure all of the holes are detonated, shotfirers are required to reenter the location to check. With advances in technology, nowadays the use of drone in mining is not something that is rarely seen. It has been used for mapping and slope-monitoring. This paper will discuss the application of drone for blasting process in a mining pit in East Kalimantan, Indonesia. By using drones, it is not only safety factor which can be improved but also operational efficiency and technical analysis. The duration it takes for post blasting process can be reduced because the drone can directly enter the location after blast. The technical analysis for the blast can also become more comprehensive, as the before-after photos and video documentation can be taken with wider view. It helps with fly rock calculation and fragmentation analysis too.

Feb 6, 2023

By Robert Hopler

CHAPTER I. DEFINITIONS AND CLASSIFICATIONS. Definition of Explosives. SECTION 1. The term “Explosive” or “Explosives” whenever used in this ordinance, shall be held to mean and include any chemical compound or mechanical mixture that contains any oxidizing and combustible units, or other ingredients, in such proportions, quantities or packing that an ignition by fire, by friction, by concussion, by percussion or by detonator of any part of the compound or mixture may cause such a sudden generation of highly heated gases that the resultant gaseous pressures are capable of producing destructive effects on contiguous objects or of destroying life or limb, and includes all the articles specifically mentioned in Section 3 herein, and all other similar articles

Jan 1, 2013

By Keith Henderson

An open pit quarry operation in West Central Illinois provided a challenging proposition regarding the removal of a rock wall that once separated two pits, but was now in the middle of the north wall of the combined pit. Their mining plan included the development of a new ramp into the quarry pit in order to lessen the slope and to shorten haul truck cycle time. The task would be to remove a section of rock left behind from mining operations more than 20 years ago that was at or near the bottom of the designed ramp.

Jan 1, 2012

By Roberto Folchi, Hans Wallin, Mara Battocchio

An understanding of explosives science and technology, and the competence to harness it is central to maintaining Explosives capability, national security, and in sustaining a competitive industry. A consequence of eroding this competence is the increased likelihood of explosives accidents. These are often catastrophic as demonstrated by accidents in Nigeria, Russia, Toulouse and Enschede. In addition to the serious loss of life there was the very significant damage to houses, domestic and industrial infrastructure and to the environment at a cost of many millions of Euros.

Jan 1, 2013

By Robert Hopler

GEO. M. MOWBRAY’S REFRIGERATOR CAR FOR THE SAFE CONVEYANCE OF EXPLOSIVES. It is a fact well known to all miners who have used nitro-glycerin, or any of its adulterations, commonly known as dynamite, rendrock, Hercules’ powder, dualin, vigorite, etc., that when congealed, these compounds cannot be exploded, and in this congealed state — say at temperatures below 40° F. — they can be handled with no more danger than a box of soap or a can of lard. If, then, the atmosphere by which this class of explosives is surrounded, during transportation, be maintained below 40° F., explosion is practically annihilated. Therefore, I constructed a refrigerator car, with cells for every box of the explosive; and two years of railroad transportation confirms our ten years’ experience in teaming in wagons, that this class of explosives can be transported in perfect safety, as above described.

Jan 1, 2011

By Robert Hopler

209. Nitro-glycerine is produced by the action of nitric and sulphuric acids on glycerine, and is a heavy liquid of oily appearance, of specific gravity about 1•6, varying from colourless when quite pure to a yellow or brownish yellow. It is of a very sweet taste, and without odour, and is an active poison. Mere handling of it will in most persons induce sickness and headache. It explodes when heated to about 360° F. or from shock, but in small quantities it ignites and burns with some difficulty by the mere contact of flame.

Jan 1, 2011

By David Leidel

A revolution in hydrocarbon well completions within the last thirty years has enabled drillers to tap the resources of known gas plays in an economically viable manner and deliver to market natural gas supplies for industrial, transportation and domestic use without the importation of liquefied natural gas from verseas. An added benefit has been the convenient location of one of these gas plays, the Marcellus Shale, in the Northeastern states strategically close to a major natural gas market, namely the cities and towns of the New England and Mid-Atlantic states. As a sidelight, the development of the tight gas reservoirs and their subsequent production has created thousands of jobs in an otherwise lackluster economy.

Jan 1, 2014

By Grant Small, Deon Pieterse

Reactive ground conditions at an open pit manganese mine in the Northern Cape of South Africa resulted in an unexpected detonation.

Feb 1, 2020