Search Documents

By Charles Hardy

ACTIVATED alumina is an aluminous material which may be 1 classified chemically as a partially dehydrated aluminum trihydrate having a high porosity and a perma¬nent physical structure. In general, it may be employed effectively and economically for the complete removal of water vapor from gases and vapors; for the selective adsorption of certain as especially those of the higher boiling points, and as a catalyst or catalyst carrier. Other forms of alumna are available and may be employed similarly but not so effectively nor can reactivation be accomplished with uniformity over many cycles without deterioration. The adsorption-reactivation cycle of activated alumina can be repeated many times without any apparent depreciation ill

Jan 1, 1934

By H. R. Stahl

FIVE mills are operated in Southeast Missouri by the St. Joseph Lead Co.; these have a total rated capacity of 24,300 tons per day divided as follows: Federal, 12,000 tons; Leadwood, 4800 tons; Desloge, 3600 tons; Bonne Terre, 2400 tons; and Mine La Motte, 1500 tons. These concentrators are similar in a general way, differing mainly in size and type of equipment and in minor variations in flow sheet. No attempt is made rigidly to standardize procedure in the various mills in spite of a general similarity in the ores. Each mill may be regarded as a separate laboratory in which new ideas and changes may be tried. A generalized description of the process is given, noting important differences in procedure at the various plants. The concentration process may be divided into five main stages: dry crushing, wet grinding, desliming and classification, tabling, and flotation.

Jan 1, 1947

By Philip E. LaMoreaux

Fluoride, generally less than 0.5 ppm, is present in ground water from rocks of Paleozoic age and older, in northern and eastern Alabama. Some of the water-bearing formations in the Coastal Plain area of the State yield water with as much as 6.8 ppm fluoride.

Jan 1, 1950

By William J. Coulter

WITHIN the past thirty years the United States has been involved in two tragic, vicious, and costly world wars. To make the world safe for democracy was the reason given for our participation, but the confusion and misunderstanding that prevails all over the world today suggests that war is not the proper approach to the attainment of that utopia. These conflicts were conceived and prosecuted by nations far advanced in civilization and culture. Their best manhood was sacrificed, a staggering tax burden was saddled on their peoples, huge financial losses were incurred, destruction of property was appalling, and cultural and peaceful scientific advancement received a setback that may require centuries to retrieve. Therefore, some basis is established for the conclusion that progress in the past fifty years has been most outstanding in the development of instruments used for death and destruction, and that progress in this direction between the two World Wars would indicate that the next war will go far toward total destruction of world civilization.

Jan 1, 1946

Willet G. Miller, Toronto, Canada (communication to the Secretary): In his interesting paper Mr. Lindgren says: " As to ultimate results, it would seem as if we should be justified in concluding, with Prof. Suess, that the gold-supply of the world will gradually decrease if no further important improvements are made in the processes for the extraction of this metal; but regarding events so far distant no predictions may safely be made." It seems to the writer that no very important improvements require to be made in order at least to keep up the present production for many years to come. In many parts of the world there are large deposits of auriferous material which can be worked if present conditions are slightly changed. In the territory occupied by the Archean protaxis of the Province of

Jan 1, 1903

By Gordon B. Brox, Joseph F. Mcaleer, Charles C. Goddard, Edward P. Shea, Robert G. Ingersoll, Lester G. Zeihen, George J. Burns, John M. Guilbert, Richard N. Miller, Charles Meyer

The Boulder batholith is a composite intrusive in which the Butte quartz monzonite is the dominant rock type. Quartz porphyry dikes intruded the quartz monzonite in directions which were subsequently followed by the eastwest- striking Anaconda system of veins, the earliest major veins in the district. Anaconda veins are faulted by northwest-striking veins of the Blue system, which are most prominent in the central third of the district. Anaconda veins are the major producers in the western third of the district and also in the eastern third, where the "horsetail" zones break off from them. Individual oreshoots are thousands of feet long as well as deep on both systems of veins, but they are generally more persistent and thicker on the Anaconda veins. Viewed broadly, the mineralization in the big veins is arranged in crudely concentric zones of zinc and manganese around a central zone of copper. Only slightly offset from these zones, but earlier structurally, is a zone in which quartz-molybdenite veinlets are prominent. This zone tops at about the 2800 level and widens downward. The pattern of distribution of Cu-Fe-S series minerals in the large veins of the copper zone is not symmetrical with respect to the metal zones. There is a fringe of chalcopyrite-bornite all around the copper front. However, within the copper zone, pyrite-chalcocite-enargitecovellite- digenite assemblages are prevalent near its eastern edge from the 3800 level to the surface, whereas deep on the large Anaconda veins in the western part of the copper zone, chalcopyrite is dominant. Here the chalcopyrite grades upward into bornite-chalcocite ores and eastward into the high-sulfur assemblages of the Leonard mine. Sericite-biotite-K-feldspar alteration envelopes, containing up to about 2 per cent copper as chalcopyrite, are present on some of the quartz-molybdenite veinlets at deep mine levels in the molybdenite zone. These envelopes contrast sharply mineralogically and chemically with the later sericitic and argillic alteration envelopes around Main Stage veins. K'0-Ar'0 ratios indicate that they may be older by about 4 m.y. Secondarily enriched copper ores are mined in the Berkeley pit in the southeastern part of the district. At the present time they account for about half of Butte's production of copper.

Jan 1, 1968

By Joseph Hartshorne

EVER since the introduction of the Siemens regenerative furnace, it has been recognized that a certain amount of gas is lost each time the furnace-action is reversed. This loss comes, first, from the gas which passes through the free connection between the stack and the gas-main, which exists during the time the reversing-valve is turning over; and, secondly, from the gas which is in the chamber and flues, from the hearth to the reversing-valve, and which flows back into the stack when the valve is reversed. The amount lost each time is, of course, small; but, since a furnace is reversed from four to six times every hour for, say, 300 days in the year, the aggregate is large enough to be well worth attention. The estimate has been published' that, in Germany alone, the loss from the first of the above causes amounts to 500,000 marks per year. The loss from the second cause is, of course, much greater. A process for saving this entire loss, in use at Teplitz, Bohemia, for about three years, would seem to be of value even in this country, where coal is cheaper and where the small economies are not watched as closely as they are in Europe. This process, invented by Mr. Adelbert Kurzwernhart, late Technical Director of the Teplitzer Walzwerk, has been worked out with thoroughness. The loss from each cause can be calculated very closely for any particular furnace, and the results to be expected from the process ascertained. It can easily be decided, therefore, whether it is worthwhile to adopt it under any given conditions. The amount of chamber-gas lost depends upon,-(1), the cubic contents of the chamber, ports and flues upon one side of the furnace, up to the reversing-valve (deducting, of course,

Mar 1, 1906

By Edward P. Barrett

DURING the past few years numerous references have been made in the technical press and Bureau of Mines Bulletin 270 to sponge iron' and so-called "direct metal" processes. The idea has been prevalent that sponge iron and "direct metals" are cheap commodities. In many instances it has been proposed that these processes be used to treat low-grade ores, utilizing low-grade coals as reducing agents. It is questionable whether or not high-grade sponge iron can be made from low-grade materials. Particles contain¬ing iron oxide and gangue become, upon almost complete deoxidation, particles containing metallic' iron and gangue. The possibility of mechanically separating the metallic iron from the gangue in these particles depends . on the physical characteristics of the particular ore under treatment. Some ores, in which the minerals constituting the gangue break free from the iron oxide upon crushing, may be concentrated magnetically after the iron oxides have been reduced to metal. The finely disseminated ores are least amenable to concentration. In general, high-grade sponge iron can only be made from high-grade raw materials. Sponge iron containing small amounts of sulfur can only be made from raw materials containing small amounts of sulfur or by

Jan 1, 1930

By A. CHESTER BEATTY

MAGNESIUM oxide is by far the most refractory of the common oxides, since it has a melting point of 5072 deg. F. as compared with 3110 deg. F., the melting point of silica (crystobalite) ; 3722 deg. F., the melting point of alumina (corundum) ; and 4127 deg. F., the melting point of chromite (Cr2O33FeO). Its large-scale use in the lining of metallurgical furnaces dates back to the latter part of the nineteenth century, when extensive deposits of magnesium carbonate were discovered in southern Austria in the province of Styria. Before the development of Austrian magnesite, calcined dolomite, a mixture of lime and magnesia, was used in basic steel-making furnaces. The lime in the dolomite was quite objectionable, since it slaked on exposure to the atmosphere, and dolomite therefore could not be made' .into permanent furnace bottoms or into brick. The Austrian magnesite, with its very low lime content, was free from these objections and soon displaced much of the dolomite. With the extensive development of basic steel-melting, the rise of the copper industry, and other metallurgical and chemical processes which dealt with chemically basic substances, the use of magnesite grain and magnesite brick increased rapidly.

Jan 1, 1931

By Raymond O. Ladoo

FUSED quartz is a glass made by the fusion of nearly pure silica. Some confusion in terminology exists but in the trade today "fused quartz" generally refers to the perfectly transparent colorless product made from rock crystal whereas "fused silica" is a white, translucent product made from silica sand. Vitrified silica is the term preferred by purists for all quartz glass, but it lacks the definiteness of -the trade terms. Since the raw materials, methods of production, and properties of the finished products arc different for the two types, the trade terms are preferred. As fused quartz is amorphous, it-physical properties differ greatly from those of quartz crystal. Lacking crystallographic directions and having no piezo-electric properties, fused quartz. of course, has no value for the making of radio oscillator plates; but it does have other valuable and unique properties. Perhaps the 'best known and most useful properties are its extremely low coefficient of expansion and its ability to transmit short-wave ultraviolet radiant energy. Crystal quartz not only has an aver-

Jan 1, 1947

By S. S. Arentz

An organized safety program has reduced accidents at Pioche because effort is first devoted to arousing and maintaining interest in safety, followed by training in accident prevention, assigning responsibility for the detection and removal of safety hazards, and finally, by keeping score through an adequate system of records. A health program is intergrated with the safety program.

Jan 1, 1950

By J. George Gregr

INTRODUCTION This part contains field case studies of typical mishaps, accidents, equipment damage or post installation failures resulting from mistakes in design, manufacturing and construction, as well as improper storage, handling and installation procedures of the equipment covered in Part 1. GENERAL Certain mistakes are repeated and common rules violated on almost all industrial equipment installations, with the inevitable consequences of additional cost, construction delays and aggravation of all parties involved. The most common failures are in the following areas: Cleanliness of all components during installation and later in operation. Adherance to manufacturer' s recommendations and tolerances for equipment installation. Comprehensive, properly identified installation and maintenance records. Handling of the components. Adequate tooling and auxiliary equipment in working order. An inoperable hydraulic power unit for torque wrench or for jacking of the mill, or faulty crane can be a very costly proposition. A special area in comminution circuits are wear components. Apart from the mill liners, the wear components such as, feed chutes, rock boxes, mill trunnion liners, discharge sumps, etc. are designed to the best theoretical configuration, based on experiences in similar installations. However, each process is different to a various degree, mainly because of various types of ores and grinding requirements. Consequently the first generation of wear components is very seldom the ideal one. Based on operational experience, the shape and material of wear components should be modified, until the optimum, most economical design is achieved. SHIPPING AND STORAGE Considerable damage to the equipment can be done by careless packing, shipping or storage.

Jan 1, 1982

By G. B. Gould

FROM the very inception of the price-control experiment in the bituminous-coal industry, the problem of price differentials was of major importance. In fact, assuming that there will be no legal or Govern- mental obstacles to price control, the successful maintenance of the present or any other method designed to control bituminous-coal prices will depend upon the discovery of some satisfactory way to determine these differentials in price, among: individual mines and groups of mines. Being of organic origin, bituminous coal is a commodity that presents an almost infinite variety of qualities. It is inevitable, therefore, that a work- able price-control system must attempt

Jan 1, 1935

By R. S. MACPHERRAN

TRENDS in the manufacture and use of cast iron are decidedly toward specialization, alloy iron, and increased strength. Old handbooks list only one kind of cast iron, with a tensile strength of 15,000 lb. Recent A.S.T.M. specifications show that from 50,000 to 60,000 lb. per sq. in. can now regularly he guaranteed. The use of alloy iron, heat-treated iron, and even nitrided cast iron, is rapidly growing and all kinds are improving in quality. Iron for operation at high temperature and corrosion-resisting irons have also been developed. Only a few years ago cast iron was "cast iron," but now there are almost as many kinds of cast iron as there are foundries making it

Jan 1, 1936

By R. E. Cuthbertson

AN early appreciation by the management that Climax ore presented a challenging problem of economic concentration was responsible for the establishment, in June 1926, of an ore-testing department at the experimental plant of the Colorado School of Mines at Golden, some ninety miles from Climax. An engineering office was later organized in the same community for the design of all ore-treatment units erected at Climax during the period of rapid growth. Work of the ore-testing and design staffs was effectively co-ordinated under a common head. The primary reason for having the ore-testing and plant design departments in Golden, was to place these activities under the able supervision of A. J. Weinig, consultant for the Climax Molybdenum Co., and director of the experimental plant. A secondary consideration was the availability of excellent facilities for research in ore dressing in a highly favorable environment. Concentration of molybdenite by flotation from an ore of simple mineral composition does not appear, superficially, to present a serious problem in ore dressing but experience belies this apparent simplicity. The molybdenite content of average Climax ore is low and it is finely

Jan 1, 1946

By C. Chamberlain

The Telfer Project, Australia's newest, largest, and most remote gold mine treats 480 kt of ore grading 9.33 g/t derived from open pit mining operations. Coarse gold is recovered by gravity concentration with jigs and further upgraded wing a continuous strake launder table, and by amalgamation. Remaining gold is recovered in a cyanide circuit and incorporates flat bottom air agitators, counter current decantation (CCD) and stellar filters for clarification and precipitate removal. Overall recovery into a bullion averages 98%. The mill incorporates a number of design features that allow for maximum efficiency and security wing a minimum number of operation personnel.

Jan 1, 1983

By Edward W. Parker

I. INTRODUCTION. AT the Seventy-sixth meeting of the Institute, held in New York, N. Y., February, 1899, I presented a, paper on this subject entitled, Coal-Cutting Machinery,' which has become somewhat out of date, in view of the decade's development in this feature of the coal-minim industry. It should be explained that the present paper is limited to the use of mining-machines in bituminous mines. Practically all of the anthracite mined is ?shot from the solid," no undercutting being done. Anthracite-mining is therefore not considered in the statistics or other references. The statistical record as compiled by the United States Geological Survey shows that in 1898, the year preceding the presentation of my former paper, there were 32,413,144 short tons of coal undercut by the use of machines. In 1907 the machine-mined coal-product amounted to 138,547,823 short tons. In sympathy with the general decrease in coal-production during 1908, the output of machine-mined coal decreased to 123,183,334 short tons, but the proportion of machine-mined coal to the total output, nevertheless, showed an increase, from 35.1 per cent in 1907 to 37 per cent in 1908. In 1898 only 19.5 per cent. of the total product was undercut by the use of machines. The number of undercutting-machines in use in the bituminous mines of the United States has increased from 2,622 in 1898 to 11,144 in 1907, and to 11,569 in 1908. The total production of bituminous coal in the United States in 1908 was almost exactly double that of 1898, while the machine- * Published by permission of the Director of the U. S. Geological Survey. 1 Trans.. xxix.. 400 to 4,59 (1899).

Sep 1, 1910

By H. P. Greenwald

THE Committee on Rock-Dusting was formed after the fall meeting of the Coal Division in Chicago in 1938. Its primary task was to study the recommended American practice for rock- dusting coal mines to prevent coal-dust explosions as approved by the American Engineering Standards Committee. After approximately two years' work he committee concluded that although certain portions of the recommended practice could well be revised, information needed for a logical revision was not at hand, and it was inadvisable, therefore, to make revisions

Jan 1, 1943

By AIME AIME

THE annual meeting of the Woman's Auxiliary to the A.I. M.E. is always held in New York, in con- junction with the annual meeting of the Institute in February. Business sessions, teas, dances, a theater party, luncheons, excursions, and many other interesting activities filled the four days to overflowing. In all ,216 women were present, from all parts of the United ,/ mates, and there were several from Canada. On Mon- ' day not only the visitors, but the New York members also, gathered around the registration desks, where Mrs. E. N. Wolfes, Mrs. S. J. Jennings, and Miss Georgene Davis saw that everyone was properly registered and provided with tickets to whatever functions she desired to attend. Greetings were eagerly ex- changed as friends met at the luncheon on the fifth floor, where the hostesses of the day were Mrs. J. D. Handy, Mrs. T. T. Read, Mrs. Sidney Rolle and Mrs. H. J. Wolf. In the afternoon, there were visits to art galleries and other interesting exhibits, arranged by Mrs. Frederick Laist. Mrs. W. H. Bassett was the hostess at a very delightful Thé damant at the Italian Gardens of the Ambassador Hotel. Many of the men attended this function also. In the evening the visiting ladies were entertained at a theater party, with Mrs. Wilbur Judson as hostess. The play that was seen was Gorki's "At. the Bottom."

Jan 1, 1930

By P. P. Gregory

ESTIMATION of re- serves in prorated sand fields has been discussed by S. A. Judson, H. D. Easton, Jr., and W. A. Schaeffer, Jr., in a paper that appears in Vol. 114 (1935), of the A.I.M.E. TRANSACTIONS. The purpose of this present paper is to extend the investigation to prorated flush limestone fields and to outline a method of procedure in determining the amount of oil originally in place and the amount of oil that can be recovered from such fields. Although it is possible to use the decline curves to estimate the amount of recoverable oil in certain limestone fields that are allowed to produce the oil at or near capacity production, such a method cannot be used in fields under severely restricted production rates. The problem is exceedingly complex due to fluctuation in the allowable rates of oil production over a wide range and at frequent intervals, and especially because of the heterogeneous nature of the reservoir itself. A well completed in a large solution cavity, capable of producing great quantities of oil per day, may be offset by a well of very limited capacity. Also, it is di5cult to arrive at an average figure for porosity in a given limestone reservoir due to abrupt variations in the character of limestone, in many instances even between two ad- joining wells. It is a safe statement that uniformity of porosity and permeability in limestone reservoirs .is nonexistent. It is evident, therefore, that the method of estimation of re- serves on the basis of per-acre content can give only approximate results.

Jan 1, 1935