Search Documents

By Stanley Rajnak, John E. Dorn

The saddle-point activation energy for the nu-cleation of a pair of kinks is estimated as a function of the applied stress, the lattice constants, and the height and shape of the Peierls' hill by employing the line-energy model of a dislocation. The kinetics of disloration motion by the Peierls' mechanism are discussed and the microscopic dislocation velocities and macroscopic strain rates are formulated by the Arrkenius type of approach in terms of the activation energy for the formation of pairs of PEIERLS was the first to illustrate that a straight-dislocation line has its lowest energy when it lies in a potential valley parallel to lines of closest packing kinks. The log of the dislocation velocity is found to be approximately proportional to the log of the local applied stress. It is also shown that the low-temperature mechmical properties of several bcc metals might be explained in terms of the Peierls mechanism, good agreement being obtained between theory and experiment for the flow stress us ternperature, activation energy vs stress, and activation volume us stress curves for these metals. of atoms on the slip plane. When such a straight dislocation is moved rigidly from one valley toward the next, the atoms in the vicinity of the core of the dislocation change their positions and bond angles, causing the energy of the dislocation to increase. Midway between two adjacent valleys, the disloca-tion energy reaches a maximum value and any additional small displacement will cause the dislocation to fall down the hill into the next valley. The maximum shear stress necessary to promote such

Jan 1, 1964

By S. C. Lindsay, D. J. I. Evans

With each year that passes hydrometallurgical processes are being more widely used to recover base metals from ores and concentrates. Generally these processes involve liquid-solid separation of metal-bearing liquors from barren residues. This may be done by countercurrent decantation, thickening and filtration, or filtration or centrifuging only. Choice of method is governed by chemical and physical characteristics of the pulps; cost of labor, power, materials, and waste disposal; and even by the amount of capital available when building plans are under way. Since all these controlling factors change with time and location and with technological advances, the separation method must be re-evaluated when new plants or expansion programs are contemplated. At the Sherritt Gordon refinery in Fort Saskatchewan, Alberta, an ammonia pressure leaching process recovers nickel, copper, and cobalt from the nickel concentrate produced at Lynn Lake, Manitoba.' Pregnant liquors are separated from the barren leach residues in a thickener-filter liquid-solids circuit. The decision to use this type of separation was based on a summation of economic factors during the pilot plant and design stages. Although countercurrent decantation was not incorporated in the refinery flowsheet, the problems solved in thickening the leach residues and the experience gained in operating the commercial plant are pertinent to countercurrent decantation, particularly where it is applied to slow-settling leach slurries or slurries having a relatively high vapor pressure of a valuable, obnoxious, or poisonous vapor. The nickel sulfide concentrate is leached under pressure with air and ammonia to dissolve the nickel, copper, and cobalt and most of the sulfur, leaving a residue of iron and siliceous material to be discarded.2,3 During a subsequent distillation stage to recirculate part of the ammonia used for leaching, copper is recovered from the solution as a high-grade sulfide. After further purification to remove traces of copper and undesirable sulfur compounds, the nickel is precipitated by hydrogen under pressure at an elevated temperature. The cobalt, together with unreduced nickel, is precipitated as a mixed metal sulfide by hydrogen sulfide for eventual cobalt recovery. The end solution is then evaporated to produce a crystalline ammonium sulfate byproduct. As shown in Fig. 1, the nickel concentrate is leached in a continuous, two-stage, countercurrent circuit. In the first stage, or adjustment leach, the fresh concentrate is partially leached (60 pct) in the liquor produced in the second stage, or final leach. This system is necessary to produce a solution suitable for treatment in the copper sulfide precipitation step. Both stages are carried out at 170" to 180°F under a total pressure, with air, of 100 to 120 psig in large, horizontal, water-cooled autoclaves. The autoclaves are divided by overflow weirs into four compartments to give a certain amount of staging during leaching. In each compartment a relatively slow-speed (100 to 150 rpm) agitator maintains the nickel concentrate in suspension. Adjustment leaching, carried out in two autoclaves in parallel, is followed by a thickener-filter liquid-solids separation. Final leaching is done in two parallel trains of three autoclaves using aqueous ammonia to extract metal values from the adjustment leach residues. This too is followed by a thickener-filter circuit. Here the residues are repulped once with aqueous ammonia and twice with process water and refiltered after each repulping stage, to insure a maximum recovery of soluble metal, before being discarded to the tailings pond. The adjustment leach is followed by a seven-disk Dorr-Oliver American filter, with an agitator in the filter boot to keep the residues in suspension. Agitators have also been installed beneath the four ten-disk filters following the final leach thickener. Slurry Characteristics: A typical analysis of the Lynn Lake nickel concentrate, produced by differential flotation,' is given in Table I. The concentrate comprises 35 to 49 pct pentlandite, (Fe, Ni)S; 3 to 6 pct chalcopyrite, CuFeS,; 1 to 4 pct pyrite, FeS2; and 24 to 42 pct pyrrhotite, Fe1-2S (where x varies between 0 and 0.2) together with various siliceous minerals such as actinolite, hornblende, and talc. During leaching, the sulfur in the pentlandite, chalcopyrite, and part of the pyrrhotite is successively oxidized through the thiosulfate and poly-thionate radicals to sulfate and sulfamate." Simultaneously the nickel, copper, and cobalt are converted to soluble ammine complexes and the iron in the pentlandite, chalcopyrite, and part of the pyrrhotite is oxidized to a spongy hydrated iron oxide. The hydrated iron oxide is readily broken down by the agitation needed to sustain the concentrate in suspension and to maintain a satisfactory mass transfer of the oxygen from the air to the slurry. Table I shows typical chemical, screen, and

Jan 1, 1961

By H. Foster Bain

I. INTRODUCTION. By H. FOSTER BAIN.+ THE recently aroused public interest in the conservation of our natural resources has peculiar importance to mining-men, since they deal with resources which are stored products. Within certain limits, the fertility of a worn-out soil may be restored, deforested areas can be replanted, one year's wasted water-supply is followed by another; but coal and ores, once taken out, cannot be mined again, and should therefore be conserved with especial care. This means, however, not that mining should be restricted, but that it should be done most economically and with the minimum of waste.

Nov 1, 1908

By J. F. Mitchell, R. Bainbridge, E. A. Melvin

IN the fall of 1953, The Consolidated Mining and Smelting Co. of Canada Ltd. put into operation a completely new and modern plant for sintering the rather complex assortment of materials which comprise the feed to the Lead Smelter at Trail, British Columbia. This Lead Smelter is one section of an integrated metallurgical plant producing lead, zinc, silver, gold, cadmium and other metals. Since most of the incoming lead concentrate contains appreci- able zinc values, and most of the zinc concentrate similarly contains appreciable lead values, the cross-routing of residues or tails from the respective lead and zinc plants offers obvious advantages in recovery of metals, and has been practiced for many years. A disparity has existed, however, between the output of zinc plant residue and the capacity of the Lead Smelter to treat it, with the result that over the years a stock-pile of residue had been accumulating, and by the end of World War II had reached the formidable total of half a million tons. To treat this stock-pile, in addition to all current zinc plant residues and, of course, the regular quota of lead concentrates, became a prime objective of the Lead Smelter following World War 11. As zinc plant residue plays an important part in the operations to be discussed in this paper, some consideration of its

Jan 1, 1958

By Charles Will Wright

MINERAL production in almost all European countries suffered a sharp setback because of the war. Plants were damaged, transportation facilities disrupted, and labor dispersed and demoralized. Since the war, due to lack of confidence and economic stability, there has been little incentive to rebuild and expand the mineral industries even though a big demand at high prices exists for mineral products. Most mining and metallurgical companies in Europe hesitate to invest their capital because of the tendency towards nationalizing industry, high taxes, and low output of labor, as well as the deficiency of mine supplies and equipment within their countries. In short, they do not have faith in the future, and for these same reasons and fears most of the mining companies in America will not risk capital investment in Europe. In Europe, including the United Kingdom, free enterprise has been losing ground and as a result the foundation of their economic welfare is being undermined. American mining interests willing to take the initiative could help in counteracting this influence if a way were found for them to co-operate with the European producer without too great a risk.

Jan 1, 1948

The problems confronting the development of Latin America's mineral resources have hinged largely on the political and economic climates-in short, the investment climate--existing and often changing in each nation. .The attractions and risks confronting today's investors in such mineral developments have been described and debated to considerable length during the past two decades, the arguments pro and con colored by the previous experiences incurred by the would-be investor, whether company or individual. In an effort to shed light on the investment climates existing today throughout Central and South America, the Council of Economics brought four experts together at the AIME Annual Meeting last March to give their views on this subject.

Jan 7, 1966

By W. C. Maurer

A drilling-rate formula for roller-cone bits is derived from rock crater-ing mechanisms. This formula holds for "perfect cleaning", which is defined as the condition where all of the rock debris is removed between tooth impacts. Under these conditions, the drilling rate is directly proportional to the rotary speed and to the bit weight squared, and inversely proportional to the bit diameter squared and to the rock strength squared. Under imperfect cleaning conditions, such m those usually present in field drilling, re-grinding of the cuttings occurs under the bit, and the drilling rates fall below those for perfect cleaning. INTRODUCTION Drilling with a roller-cone bit consists of two fundamental operations: the formation of craters under the bit teeth, and the removal of the broken rock from the craters. To delineate the mechanisms of drilling, it is first necessary to understand the mechanisms involved in the formation of individual craters and then to relate these mechanisms to the over-all drilling operation. CRATER FORMATION When a bit tooth impacts a rock, the rock is elastically deformed until the crushing strength of the rock is exceeded, at which time a wedge of crushed rock is formed below the tooth1, 2 as shown in Fig. 1. As additional force is applied to the tooth, the crushed material is compressed and exerts high lateral forces on the solid material surrounding the crushed wedge.- en these forces become sufficiently high, fractures are initiated below the tooth and propagate to the free surface of the rock. The trajectories of these fractures intersect the principal stresses at a constant angle,'s4, as predicted by both Mohr's and Griffith's theories of failure. It has been experimentally 3,1 .6 that the volume of an impact crater, V,, varies as where Ec is the total energy imparted to the rock during the formation of the crater, and E is the threshold energy required before cratering is initiated (Fig. 2). Indexing experiments' have shown that, when there is a second free face to which the crater can fracture, a larger volume of material is removed and that above a transition zone there is a linear relationship between V, and Eo., which has a slope equal to the relationship for the single crater. The beneficial effect of indexing tends to offset the threshold energy requirement to a large extent, as shown in Fig. 2, and the relationship is closely represented by Rate-of-loading effects have been used to explain the nonproportional relationships usually obtained between drilling rate and rotary speed. The data4, in Fig. 3 show that the Ec/Vc parameter remained constant for craters produced with impact velocities ranging from 10 to 8,000 ft/sec. Since no rate-of-loading effects were detected over this wide range of loading rates, it seems improbable that there would be detectable rate-of-loading effects present in the small changes in impact velocities produced by varying the rotary speed. The writer has shown (Fig. 4) that, for craters produced in rock by impacting spheres, where X is the depth of penetration. Simon2 has shown that this relationship also holds for craters produced in rock by penetrating wedge-shaped chisels. The energy used in crater formation is

By Kendall E. Born

Production of crude oil in Tennessee during 1941 was slightly more than 15,000 bbl., about the same as in the preceding year. Two thirds of the total was from the Mississippi limestone pools in Scott and Morgan Counties. About a dozen small scattered wells in Clay, Pickett, and Fentress Counties, pumped irregularly, produced approximately 5000 bbl. Natural gas was marketed from wells in Morgan and Fentress Counties for consumption in the Sunbright and Jamestown areas, respectively. The production by counties is shown in Table I. Drilling activities in the state fell to the lowest stage since 1933. Twenty-seven wells were spudded in during 1941, of which six were drilling or only temporarily suspended on Dec. 37, 1941. Of the 22 completions, four were gas wells of undetermined quantity, but are classed as commercial, and 17 were dry or near-dry holes. One well encountered oil, but it has not been tested. The total footage drilled during the year was 29,916 ft.; the average depth of wells was 1359 ft. The more important wildcats are listed in Table 2; the distribution of tests according to physiographic divisions is given in Table 3. East Tennessee.—One well was drilled to 3480 ft. in northwestern Anderson County, in the highly disturbed Appalachian area, a region long considered the most unfavorable in the state for the accumulation of oil and gas. Another test is now drilling below 2000 ft. in this general area. Cumberland Plateau.—There were two completions in the Cumberland Plateau area. One test, drilled in northwestern Scott County in an area of former Mississippi limestone production,' encountered a considerable amount of free oil at 850 ft., about the same horizon as in the old abandoned wells. No pumping tests have been made to date. A well at Oneida, Scott County, found gas at 1579 ft. in a sandy limestone of lower Mississippian age. The volume was reported doubled by a shot, although no open-flow measurement is available. Eastern Highland Rim.—Six completions on the eastern Highland Rim resulted in two small gas wells in Fentress County, which will be used to augment the supply for Jamestown. The producing horizons are shaly limestones of Ordovician (Trenton) age. Two wells in this area tested the upper part of the Knox dolomite group, one of which encountered some free oil in a sandy dolomite at 1670 to 1681 ft. A test high on a well-defined structure in Clay County found a considerable amount

Jan 1, 1942

JESSE L. JONES,* Pittsburgh, Pa. (written discussion?).-As the die-casting process is so very different in character from the process of making sand molds, it is often considered that entirely different methods of pouring, gating, venting, etc. should be used. There is really, however, no essential difference in the making of (lie castings and sand castings, and similar methods should be used in each process. In the matter of gating, the metal should be introduced at a central point, as nearly as possible, so that it will have an equal distance to flow from the point of entrance to the most distant points of the mold. This will cause a uniform rate of congealing of the casting and prevent streaks and cold shuts. The venting should be done in such a way that a free exit of the air in the molds can occur. It should be less difficult to take care of the venting of a die-casting mold than to vent an ordinary sand mold. In the case of a sand mold, the venting is left, to a considerable extent, to the judgment of the molder, and it is possible that no two molds will be vented in a similar manner. Further than this, after a vent has been made in a sand mold, it may become clogged by the sand and for this reason be inefficient. There is also quite a variation in the pressure of the metal entering a sand mold, due to varying heights of the pouring gate. In a die-casting mold these factors can be controlled more closely. The vents should be so disposed that the air in the mold compressed by the entrance of the metal may be able to leave the mold at a uniform rate and by exits located symmetrically. These exits are made quite small on molds at first, as they can he easily enlarged if necessary, and they are tapered so that a free flow is guaranteed without danger of the metal spurting out from the die. Uniformity of pressure of the metal as it enters the mold is very important and, as the pressure is mechanically applied, its control is not difficult. It is true that a sand mold has much less of a chilling effect on the metal poured into it than has the die-casting mold, but, outside of this point, there is a great similarity between the die-casting process and the process of making castings in sand folds. It is suggested that much would be gained by regarding these two processes as not essentially different.

Jan 4, 1919

By R. Adair, W. R. Hudspeth, W. T. McDaniel

D. C. Ralston (U. S. Bureau of Mines, Washington, D. C.)—Flake mica can be beneficiated by a wider variety of methods than almost any known mineral. However, most of these methods are not recorded. It is therefore a pleasure to find a written record of another application of a new method of beneficiation. The fact that the Humphries spiral gives a concentrate containing the mica flake mixed with the slime and small grit has forced a further separation by screening, in which the finest of the flake will pass through. Fine flake has its uses and if mixed with slimes or clay is recoverable reliably only by flotation. This loss must be charged against the spiral. On the other hand, the new muscovite mica paper recently brought out by General Electric Co., can be made only with grit free flake larger than 50 mesh. It is of interest to learn from the authors whether the washing of the flake on a 50 mesh screen can take the grit content below 1 pct, to meet this new demand. Must another degritting process be used on the flake, like electrostatic treatment of the dried material? H. D. Snedden (The Humphreys Investment Co., Denver)—When recovering mica in the spiral, gangue particles coarser than 16 mesh can be rejected more readily when operating at a high pulp density (35 pct solids) or a low volume rate (—15 gpm). A launder screen as used by Lehigh Coal Co. has proved very satisfactory to partially dewater the mica concentrate and to reject any gangue slimes it may contain. Under certain conditions mica cleaning in the spiral can be improved by reagentizing the spiral feed, the object being to insure wetting of the gangue minerals and to agglomerate or prevent wetting of the mica particles. R. B. Adair (authors' reply)—The grit content of the mica recovered on Humphreys Spirals varies with the fineness of the launder screen used to clean the mica product. Normal practice has been the use of 80 mesh screen, which will produce a mica product of acceptable grit content for most purposes. By using a 50 mesh screen, and increasing the screen area per ton of feed, it is felt by the authors that a mica of 99 pct plus purity could be obtained. This statement would hold only in the case of mica feed which was well de-laminated, and free from "clay balls," (semikaclinized feldspar), which tends to follow the mica through the process.

Jan 1, 1952

By Fred Wise, C. W. Wark

THE Getchell mine, a comparatively recent gold discovery, is in the old Potosi mining district, Humboldt County, Nevada. All ore is mined from open pits using Diesel shovels and gasoline trucks. Two types of ore are mined, oxide and sulphide. Oxide ores are siliceous or shaly; sulphide ores either gougy, siliceous or shaly. In mining, the sulphide ore is segregated into hard and gougy ore, because the gouge must be dried before it can be crushed. The oxide ore is not segregated. GENERAL METALLURGY The oxide ore is the leached outcrop that overlies the sulphide ore body. All of the iron and arsenic sulphides found in the sulphide ores have been thoroughly oxidized. The sulphur and arsenic have been leached out while the iron is present as hematite and limonite. The oxide ore is amenable to direct cyanidation, and although no visible free gold is present it is released at a comparatively coarse grind. The sulphide ore is more refractory, since the gold is all of micron size and some of it is locked in fine sulphides. It has been established microscopically that the free gold is coated with an impervious shell, which is probably some form of iron compound. The sulphide ores contain from 1.5 to 2 per cent of arsenic, which is present as orpiment and realgar with minor amounts of arsenopyrite. The orpiment and realgar are of a later mineralization than the gold and are barren. Roasting and washing of the sulphide ore prior to cyanidation is necessary to eliminate the arsenic, to alter the gold coating from an insoluble form to a soluble form, and to release the gold associated with the fine sulphides. Washing the ground calcine in weak sulphuric acid, trona, or hot water are beneficial in the order named, but to date the water is the best from an economic standpoint. Metallurgical tests as well as plant practice indicate that a certain amount of gold cannot be recovered even by going beyond economic practices. On this basis metallurgical results are viewed in the light of an optimum tailing rather than a percentage of extraction. MILLING PRACTICE Crushing (Fig. 1).-There are three primary ore bins, one each for oxide ore, gougy sulphide ore, and hard sulphide ore. In front of each bin a substantial yard is maintained, which makes it possible to stockpile 2500 tons of oxidized ore, 1000 tons of hard sulphide ore, and 1000 tons of gougy sulphide ore. The bins are fed by a 60-hp. caterpillar bulldozer from the stockpiles. Fig. 1 shows the method and

Jan 1, 1940

By Kendall E. Born

Production of crude oil in Tennessee during 1941 was slightly more than 15,000 bbl., about the same as in the preceding year. Two thirds of the total was from the Mississippi limestone pools in Scott and Morgan Counties. About a dozen small scattered wells in Clay, Pickett, and Fentress Counties, pumped irregularly, produced approximately 5000 bbl. Natural gas was marketed from wells in Morgan and Fentress Counties for consumption in the Sunbright and Jamestown areas, respectively. The production by counties is shown in Table I. Drilling activities in the state fell to the lowest stage since 1933. Twenty-seven wells were spudded in during 1941, of which six were drilling or only temporarily suspended on Dec. 37, 1941. Of the 22 completions, four were gas wells of undetermined quantity, but are classed as commercial, and 17 were dry or near-dry holes. One well encountered oil, but it has not been tested. The total footage drilled during the year was 29,916 ft.; the average depth of wells was 1359 ft. The more important wildcats are listed in Table 2; the distribution of tests according to physiographic divisions is given in Table 3. East Tennessee.—One well was drilled to 3480 ft. in northwestern Anderson County, in the highly disturbed Appalachian area, a region long considered the most unfavorable in the state for the accumulation of oil and gas. Another test is now drilling below 2000 ft. in this general area. Cumberland Plateau.—There were two completions in the Cumberland Plateau area. One test, drilled in northwestern Scott County in an area of former Mississippi limestone production,' encountered a considerable amount of free oil at 850 ft., about the same horizon as in the old abandoned wells. No pumping tests have been made to date. A well at Oneida, Scott County, found gas at 1579 ft. in a sandy limestone of lower Mississippian age. The volume was reported doubled by a shot, although no open-flow measurement is available. Eastern Highland Rim.—Six completions on the eastern Highland Rim resulted in two small gas wells in Fentress County, which will be used to augment the supply for Jamestown. The producing horizons are shaly limestones of Ordovician (Trenton) age. Two wells in this area tested the upper part of the Knox dolomite group, one of which encountered some free oil in a sandy dolomite at 1670 to 1681 ft. A test high on a well-defined structure in Clay County found a considerable amount

Jan 1, 1942

By C. E. Birchenall

DaVIES and Richardson1 have measured composition changes for Mn1-Owith variation in the equilibrium partial pressure of oxygen at 1500°, 1575°, and 1650°C, where 6 is the deviation from the simple stoichiometric ratio. No trend in this relationship with temperature was observed, so these remarks apply to the whole temperature range. The experimental values and their spread are shown by the bounded straight-line segments in the figure. Davies and Richardson assume that the stoichiometric oxide shows Frenkel disorder, given by the equation Mn2+Mn2+ + Mn" [1] where Mn2+ is a normal lattice ion which moves into an interstitial site (Mni2+) leaving a vacancy (Mn,"). The superscript dashes indicate that there is an excess charge on the anions surrounding the vacancy. Schottky disorder, in which a perfect crystal acquires equal numbers of cation and anion (Ov") vacancies according to leads to equations of exactly the same form in the analysis below. In view of the neutron diffraction results of Roth,2 which shows extensive Frenkel disorder in Fe1-o, Eq. [I] seems more appropriate. The deviations from stoichiometric composition, MnO, result from the addition of oxygen according to In effect Davies and Richardson ignore the variation of Mn3+in constructing equilibrium constants. This approximation might not appear to be very serious if the excess positive charges are really free posi- tive holes (P+) and if the intrinsic conductivity is high as a result of the reaction where e- is a conducting electron. However, the calculations of Buessem and Butler3 indicate that the partition functions of the free charges make a large contribution to the equilibrium constant, and this approximation would not be a desirable one. Furthermore, Morin4 shows that the positive holes are probably localized in MnO and therefore are described better by the mass action principle than by a degenerate gas model. Davies and Richardson's considerations require that activity corrections be applied beyond a 6 value of about 0.005. It is proposed to show here that the dissociation pressure curve can be calculated reasonably well over the whole composition range studied without activity corrections by choosing appropriate equilibrium constants for reactions 1 and 2. As stoichiometric composition The mass action constant, Ks, for reaction [I.] and the equilibrium constant, K,, for reaction [2] are given by where the concentrations which do not change significantly have been absorbed into the constants. The brackets denote concentrations. The deviation from stoichometric composition is given by gardless of [Mni2 ]. Substituting Eq. [7] in [6]

Jan 1, 1961

By C. W. Wark, Fred Wise

The Getchell mine, a comparatively recent gold discovery, is in the old Potosi mining district, Humboldt County, Nevada. All ore is mined from open pits using Diesel shovels and gasoline trucks. Two types of ore are mined, oxide and sulphide. Oxide ores are siliceous or shaly; sulphide ores either gougy, siliceous or shaly. In mining, the sulphide ore is segregated into hard and gougy ore, because the gouge must be dried before it can be crushed. The oxide ore is not segregated. General Metallurgy The oxide ore is the leached outcrop that overlies the sulphide ore body. All of the iron and arsenic sulphides found in the sulphide ores have been thoroughly oxidized. The sulphur and arsenic have been leached out while the iron is present as hematite and limonite. The oxide ore is amenable to direct cyanidation, and although no visible free gold is present it is released at a comparatively coarse grind. The sulphide ore is more refractory, since the gold is all of micron size and some of it is locked in fine sulphides. It has been established microscopically that the free gold is coated with an impervious shell, which is probably some form of iron compound. The sulphide ores contain from 1.5 to 2 per cent of arsenic, which is present as orpiment and realgar with minor amounts of arsenopyrite. The orpiment and realgar are of a later mineralization than the gold and are barren. Roasting and washing of the sulphide ore prior to cyanidation is necessary to eliminate , the arsenic, to alter the gold coating from an insoluble form to a soluble form, and to release the gold associated with the fine sulphides. Washing the ground calcine in weak sulphuric acid, trona, or hot water are beneficial in the order named, but to date the water is the best from an economic standpoint. Metallurgical tests as well as plant practice indicate that a certain amount of gold cannot be recovered even by going beyond economic practices. On this basis metallurgical results are viewed in the light of an optimum tailing rather than a percentage of extraction. Milling Practice Crushing (Fig. I).—There are three primary ore bins, one each for oxide ore, gougy sulphide ore, and hard sulphide ore. In front of each bin a substantial yard is maintained, which makes it possible to Stockpile 2500 tons of oxidized ore, 1000 tons of hard sulphide ore, and 1000 tons of gougy sulphide ore. The bins are fed by a 60-hp. caterpillar bulldozer from the stockpiles. Fig. I shows the method and

Jan 1, 1943

By R. I. Jaffee, R. W. Wood, H. R. Ogden, D. N. Williams

D. W. Morgan, D. H. Polonis,and R Taggart (Uuivevsity of Washington)—Dispersion hardening in titanium-copper alloys is of particular interest to us in view of our current research activities in phase transformations in this system. We should like to raise questions concerning several points in the paper. The flow sheet for fabrication and heat treatment (Authors' Fig. 2) indicates that 0.045 in sheet is treated in air for a period of 30 min at 1625' F. Were any surface coatings used to reduce oxygen contamination at this stage? One might ask the same question about the 8-hr annealing at 1400F. Contamination during fabrication and heat treatment of such thin sections could be considerable without some protection. Although the authors state that no analyses were made, they note that contamination masks the distinction between base strengths of the different alloys. In this connection, what fabrication and heat-treatment procedures were used in obtaining the comparison specimens of unalloyed titanium? It would seem that oxygen contamination must cast doubt on the reliability of the proposed strength-mean free path relationship deduced from the data (Authors' Fig. 5). It is usual to evaluate dispersion hardening on the basis of yield strength rather than ultimate tensile strength, and accordingly we have replotted the authors' Fig. 1 to include yield strength. The yield strength data do not justify a discontinuity of 3 p at either 70" or 1000 OF. Can the authors substantiate their conclusion 1) with additional evidence? Otherwise it seems that they have succeeded only in pointing out the possibility of a linear relationship between yield strength (or Uts) and the logarithm of the nleall free path, comparable with that demonstrated for iron-carbon alloys (Authors' Ref. 2). Work in our own laboratories has shown that the hardness of the phase Ti,Cu is 235 Vpn, and that of a 1.5 pct (at.) (2 pct wt) supersaturated solid solution of copper in titanium is 190 Vpn. This small difference in hardness would suggest that Ti2Cu should not be a very effective dispersion-hardening phase. D. N. Williams, R. W. Wood, H. R Ogden, RI. L Jaffee (authors' reply)— This discussion brings out some interesting points with respect to the interpretation of our results, and also raises some questions regarding the experimental technique. We shall consider the latter questions first. Contamination during heat treatment was prevented by performing all heat treatments in argon-filled Vycor capsules. Fabrication was done in air, with the usually observed scaling. Scale was removed

Jan 1, 1962

Gentlemen.-The Institute was founded 54 years ago "with the object of promoting the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by means of meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members and associates the information thus obtained," At least once a year it is well to take stock of our assets, review our performance and determine how well we are now carrying out the purposes of our Founders. There can be no question as to the work the Institute has done and is doing in promoting the arts and sciences in the fields of mining and metallurgy. One needs only to contrast the methods, the labor and the costs of a half century ago with those now to visualize how far we have gone in the development of accurate technology and sound economics in mineral and metal production. The great mines, mills and smelters of the present, handling individually thousands of tons per day, would' have been impossible except for the accumulation of knowledge, the development of theory, and the improvement in practice that has characterized the period since the foundation of the Institute. The United States has prospered in the last half century greatly, and this has been due not merely to the possession of great natural resources, but to these resources being reduced to possession and put to work. The absence of customs barriers and the freedom of trade across the whole width of this great continent has been an important factor in the growth of our wealth. Unrestricted interchange of goods has permitted each citizen to draw on the resources of the whole country. However, these are but subsidiary causes of prosperity. The free interchange of scientific and technical data, by making the whole body of facts and theory available to each worker, has made this quick and unrivaled development possible. In promoting this free trade in knowledge the Institute may claim a large place without fear of denial. The .72 volumes of TRANSACTIONS, the special volumes, the bulletins and the other publications that have been issued, include a store of knowledge of the arts and sciences related to the production and use of metals and minerals not duplicated elsewhere. The large list of foreign members-1746 in number-few of whom ever have opportunity to attend meetings and all of whom derive their main benefits from membership through the pub-

Jan 1, 1928

By Leland L. Mink, Roy E. Williams, C. Daniel Kealy

The passage by Congress of Public Law 92-500 (the 1972 Water Pollution Control Act amendment) has placed a new emphasis on the need for methods to minimize the escape of water from tailings ponds. Presumably tailings pond seepage will fall under the jurisdiction of the act. This paper is designed to explain some of the problems caused by leakage from tailings ponds and to present a method by which leakage can be minimized if not eliminated. Ground-water pollution in one case studied by the authors results from leaching of old jig tailings that are intermixed with the upper part of a sand and gravel aquifer. Anomalous concentrations of zinc, lead, and cadmium occur in ground water and soil samples taken from the portion of the sand and gravel aquifer containing the old jig tailings. Analysis of water samples from a tailings pond located in the area indicates that the pond water is not the source of the heavy metal concentrations found in the down-gradient ground water. However, leakage from the pond and water from the pond's decant system combine with natural ground water to compound the problem by raising the water table into old jig tailings which cover the upper portion of the aquifer. The ground water which discharges from this aquifer causes a statistically significant decrease in the quality of the receiving stream water. The shallow ground water contains oxygen; therefore, corrective measures include lowering the water table to depths below the old jig tailings which cover the aquifer at ground level. This, in turn, implies elimination of ground-water recharge by subsurface leakage from the pond. A laboratory study and a mathematical model study have revealed that seepage from such ponds can be minimized by a carefully designed and managed peripheral tailings discharge system. The process involves maintaining the slime zone and the free-water surface near the center of the pond so that the slimes retard downward and semilateral movement of pond water. The free-water surface must not be allowed to extend out over the nonslime portion of the tailings during or after pond operation. Mathematical model output reveals that this method can hold the subsurface discharge rate to as little as 110 gpd per acre of pond water area. The technique should be applicable to any tailings pond system in which the loss via seepage of poor quality water must be minimized or where recharge of ground water by losses from a tailings pond must be minimized, regardless of the reason.

Jan 1, 1974

By W. B. Humes

The use of high vacuum on a large industrial scale in the ferrosilicon process for the production of magnesium marks the coming of age of an important new metallurgical technique. The economical production of reactive metals, such as magnesium, which combine with all the well-known furnace atmospheres, has until recently been successfully carried out only by electrolytic methods. It is now apparent that, through the use of high vacuum, the distillation or sublimation of many metals can be done industrially at much lower temperatures, and hence in much simpler equipment, than heretofore has been thought possible. At the beginning of the present emergency, when the ferrosilicon process of producing magnesium was brought to the fore, little was generally known about vacuum engineering, practices, and techniques. In a comparatively short time, the available equipment has been adapted, new equipment designed and built, and a fund of know-how evolved to make possible the production of thousands of pounds of magnesium per day at pressures less than 1/ r0,000 of an atmosphere. Pilot-plant operations have been consistently maintained at pressures even as low 2s one micron (0.001 mm.). These low pressures, which previously were regarded as prohibitively costly or impossible to attain, have been demonstrated as economically feasible on an industrial scale. Necessity for Vacuum The main function of vacuum in the ferrosilicon process, and hence in most vacuum smelting processes, is to lower the temperature at which the metal may be distilled or sublimed from the reduction mixture. A secondary function is to protect the distilled metal from attack by the furnace atmosphere and to permit the formation of a dense condensate. In the ferrosilicon process, magnesium is formed by the reaction between dolomite and ferrosilicon: 2(Mg0-Ca0) -\- HFeSU / t=> aMg + MFe + (CaO)2-SiO2 The metal is distilled from the pelleted charge at a free air pressure of about 0.100 mm. of mercury (100 microns). This low pressure is not needed for the reaction, but rather serves to protect the metal vapor from the oxygen or nitrogen of the atmosphere and permits the formation of a condensate free of pyrophoric material. The reaction proceeds at air pressures as high as several millimeters of mercury, and evidence has been offered to show that the actual equilibrium pressure of magnesium at operating temperatures of 2I50°F. is somewhat higher. Experimentation indicates that the yield begins to decrease at pressures above 500 microns. While no real operating data are yet available on the relationship between

Jan 1, 1944

By Fred Wise, C. W. Wark

The Getchell mine, a comparatively recent gold discovery, is in the old Potosi mining district, Humboldt County, Nevada. All ore is mined from open pits using Diesel shovels and gasoline trucks. Two types of ore are mined, oxide and sulphide. Oxide ores are siliceous or shaly; sulphide ores either gougy, siliceous or shaly. In mining, the sulphide ore is segregated into hard and gougy ore, because the gouge must be dried before it can be crushed. The oxide ore is not segregated. General Metallurgy The oxide ore is the leached outcrop that overlies the sulphide ore body. All of the iron and arsenic sulphides found in the sulphide ores have been thoroughly oxidized. The sulphur and arsenic have been leached out while the iron is present as hematite and limonite. The oxide ore is amenable to direct cyanidation, and although no visible free gold is present it is released at a comparatively coarse grind. The sulphide ore is more refractory, since the gold is all of micron size and some of it is locked in fine sulphides. It has been established microscopically that the free gold is coated with an impervious shell, which is probably some form of iron compound. The sulphide ores contain from 1.5 to 2 per cent of arsenic, which is present as orpiment and realgar with minor amounts of arsenopyrite. The orpiment and realgar are of a later mineralization than the gold and are barren. Roasting and washing of the sulphide ore prior to cyanidation is necessary to eliminate , the arsenic, to alter the gold coating from an insoluble form to a soluble form, and to release the gold associated with the fine sulphides. Washing the ground calcine in weak sulphuric acid, trona, or hot water are beneficial in the order named, but to date the water is the best from an economic standpoint. Metallurgical tests as well as plant practice indicate that a certain amount of gold cannot be recovered even by going beyond economic practices. On this basis metallurgical results are viewed in the light of an optimum tailing rather than a percentage of extraction. Milling Practice Crushing (Fig. I).—There are three primary ore bins, one each for oxide ore, gougy sulphide ore, and hard sulphide ore. In front of each bin a substantial yard is maintained, which makes it possible to Stockpile 2500 tons of oxidized ore, 1000 tons of hard sulphide ore, and 1000 tons of gougy sulphide ore. The bins are fed by a 60-hp. caterpillar bulldozer from the stockpiles. Fig. I shows the method and

Jan 1, 1943

By E. R. Parker, D. L. Martin

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944