Search Documents

By Frederic Benard

This paper constitutes a preliminary report on experimental work done to date on the anode-furnace treatment of blister copper containing relatively high percentages of nickel. The investigation has not been completed but results obtained to date are considered of sufficient interest to warrant publication. Blister copper treated by the Ontario Refining Co. originates from the Copper Cliff smelter of The International Nickel Company of Canada, of which the former is a wholly-owned subsidiary. The blister as received contains from 0.50 to 1.50 per cent Ni, and in this respect differs from that treated by other refineries on this continent. During the anode-furnace treatment, only a portion of the nickel content is removed, and of the amount remaining in the anodes a varying percentage is found in the anode slimes. This necessitates a more extensive treatment than ordinary nickel-free material. Sometimes it is necessary to repeat roasting and leaching operations several times before the nickel colltent is low enough to permit the slimes to proceed to the dorè furnace. This, besides increasing treatment charges, causes greater selenium stack losses and involves a longer tie-up of precious-metal values. Therefore this investigation was undertaken with the aim of determining the factors influencing the diversion of nickel into the anode sludge. From experience it was known that by keeping the nickel content of anodes at 0.55 to 0.60 per cent maximum a relatively satisfartory slime resulted. One avenue of attack therefore was developing improved elimination in the anode-furnace treatment so that the anode content mentioned above was not exceeded. Another angle was to improve the solubility, during electrolysis, of the nickel constituent in the anodes, thus decreasing the percentage diverted to slimes. . It may be mentioned here that nickel dissolving electrochemically and entering the electolyte presents no difficulty from a treatment standpoint. Both of these approaches were studied and are discussed separately below.

Jan 1, 1943

By E. T. Dumble

For many years there have been occasional reports of the discovery of gold from a belt of the coast country of Texas which is underlain by deposits belonging to the lower Eocene. For the most part they have been treated as newspaper reports and no examination or record of them has been made. Among such, it may be mentioned that in 1896 there was a flurry over reported gold-discoveries west of Luling and elsewhere in this belt, and in 1903 some prospect-shafts were sunk on the Gon-zales branch of the Galveston, Houston & San Antonio railway, 3 miles below Harwood. During 1912, further discoveries have again brought the matter to our attention, and it may be of interest to record the facts as we have found them. Some years ago specimens were sent me, which were said to have been taken from certain beds on Gazley creek, and concentrated by washing in a rocker. In them were several particles of gold sufficiently large to be visible to the eye. Under the microscope they showed to be, with few exceptions, sharp cornered, and not rounded as is usual with placer-gold. They were not filings, however, but their sharpness seemed rather to be due to a recent freeing from their matrix. One or two grains were rusty, and one copper-hued, but the most of them were tolerably bright. On examining the material of the samples small grains or fragments were found, of a yellowish brown color, which seemed to be of a finely-granular structure—possibly a sandstone. In these fragments I found particles of gold, one of them being large enough to be visible without a lens. Gazley creek empties into the Colorado river just north of Smithville, and for a few miles north of that place its banks show, beneath the deposits of more recent materials, the sands and clays of the Lignitie division of the Eocene, with lignite, shells of iron, etc.

Jan 1, 1913

By Frederic Benard

THIS paper constitutes a preliminary report on experimental work done to date on the anode-furnace treatment of blister copper containing relatively high percentages of nickel. The investigation has not been completed but results obtained to date are considered of sufficient interest to warrant publication. Blister copper treated by the Ontario Refining Co. originates from the Copper Cliff smelter of The International Nickel Company of Canada, of which the former is a wholly-owned subsidiary. The blister as received contains from 0.50 to 1.50 per cent Ni, and in this respect differs from that treated by other refineries on this continent. During the anode-furnace treatment, only a portion of the nickel content is removed, and of the amount remaining in the anodes a varying percentage is found in the anode slimes. This necessitates a more extensive treatment than ordi-nary, nickel-free material. Sometimes it is necessary to repeat roasting and leaching operations several times before the nickel content is low enough to permit the slimes to proceed to the doré furnace. This, besides increasing treatment charges, causes greater selenium stack losses and involves a longer tie-up of precious-metal values. Therefore this investi-gation was undertaken with the aim of determining the factors influencing the diversion of nickel into the anode sludge. From experience it was known that by keeping the nickel content of anodes at 0.55 to 0.60 per cent maximum a relatively satisfactory slime resulted. One avenue of attack therefore was developing improved elimination in the anode-furnace treatment so that the anode content mentioned above was not exceeded. Another angle was to improve the solubility, during electrolysis, of the nickel constituent in the anodes, thus decreasing the percentage diverted to slimes. It may he mentioned here that nickel dissolving electrochemically and entering the electolyte pre-sents no difficulty from a treatment standpoint. Both of these approaches were studied and are discussed sepa-rately below.

Jan 1, 1938

By John Mathews

CERTAIN physical and chemical properties of copper are so intimately related that a change in variation of the physical properties indicates a certain chemical change. The standard specifications of copper of the American Society for Testing Materials are based upon physical characteristics with one exception, namely, the copper contents. The physical standard includes electrical properties, defects in the "set or casting," variation in dimensions, weight, etc. Paragraph 4 of the specifications states, " Wire bars, cakes, slabs and billets shall be substantially free from ;shrink holes, cold sets, .pits, sloppy edges, concave tops, and similar defects in set or casting." Shrink holes and concave tops indicate both physical and metallurgical defects; cold sets, sloppy edges, etc., indicate physical defects only; small pit holes may be indicative of either or both physical and metallurgical defects, depending on conditions under which they originated. To the refiner, a copper casting, no matter how made, is known as a "shape," irrespective of whether it is wire bar, ingot, cake, slab, billet, etc. As practically all shapes are cast in an open mold, that is a mold without cope, the surface of the shape cools in contact with the atmosphere and has a coating of oxide. Certain phenomena of the surface indicate the adaptability of the metal for forging or rolling. The writer believes that it is much simpler to produce shapes that are metallurgically correct than those that are mechanically satisfactory. When copper is to be rolled into thin sheets or drawn into very fine wire, the slightest physical defect becomes evident. It is, therefore, of the utmost importance to, consider every characteristic of the shape and ascertain the physical and chemical relationship. Pitch and Set.-The appearance of the surface of the copper when cooled is considered as to its "pitch," or the general contour of the surface of the shape (which may vary from a concave to a convex); and the "set," or the detail appearance of the surface of the shape (the wave-like struc-

Jan 2, 1920

By H. Ries

IN THE marketing of mineral products, it is always highly desirable for both the producer and the consumer to be able to discuss things in a common language, and this can only be done if there are standard methods for expressing the properties of the raw materials. Having developed such a form of expression, the next step would be the making of specifications, which may serve as a basis for selecting raw materials. Considering the large number of non-metallic minerals that are used, there are not a few for which there are no standard laboratory tests to be used in determining their properties, or even standard specifications on which grades or market price may be based. Indeed in many cases the consumer simply requests the producer to submit samples, and rejects or accepts them without any explanation. Could the producer know in advance just what the consumer needed, time and money might often be saved. It appears to the writer that it is of the highest importance to devise standard laboratory tests wherever possible, as this enables the consumer to state definitely what he needs, and is of great assistance to the producer. It should also work to reduce misunderstandings and disputes. 'In the case of sands, we find that they show a wide variation in their character, ranging from those that are so coarse as to be of gravelly nature to those that are so fine that they might be classed as silt; and from very clayey ones to those that are practically free from clay. For this wide range of sands, we have a corresponding variety of uses, which are based mainly on the physical properties of the sand, although these are not always very definitely stated. The chemical composition need rarely be considered, if the sand is of siliceous nature. To determine and express these properties there should be standard tests, which are to be followed in all cases where the material is tested in the laboratory.

Jan 1, 1926

By G. Czupryna, S. Natansohn

Electrowinning is the prevalent technique for recovering silver from wastes generated in silver-tungsten electrical contact fabrication. Such scrap is placed in a permeable plastic basket, which constitutes the anode compartment, and is suspended in a larger cell where the cathode is mounted. A silver nitrate solution is used as the electrolyte and, upon application of an electric field, the silver migrates to the cathode where it deposits. At times, there is tungsten migration to the cathode compartment and consequent co-deposition with the silver. This W contamination, which may amount to several thousand mg/L (oz per gal), necessitates additional purification of the deposited Ag and its removal would, therefore, be advantageous. Eliminating the W impurity also extends the operating period of the cell with corresponding increases in the Ag output and savings in labor costs. The solution to this problem lies in the selective removal of the W from the AgNO3 electrolyte either by liquid-liquid or liquid-solid extraction. Although W extraction in the liquid-liquid mode with a quaternary amine or other reagents as extractants appears feasible, particularly in view of the low pH (about 1.5) of the system, this approach was not considered because it is essentially a batch-type process. It is a more elaborate industrial operation than extraction by ion exchange resins. Implementing the latter process consists of passing the electrolyte from the electrowinning cell through an ion exchange column which would extract the tungsten selectively and returning the tungsten-free stream to the cathode compartment. This process continues until the W extraction efficiency decreases (as a result of resin loading) below an acceptable value. The electrolyte is then directed through another, similar column while the W values are eluted off the first one and the resin is regenerated for another cycle. Thus, two columns in a parallel flow pattern provide the means for continuous processing of the electrolyte feedstock.

Jan 1, 1984

By Karl Sundberg

DURING the past few years Swedish geo-electrical prospecting methods have been described in several papers; namely, by us in a paper en-titled "Electrical Prospecting in Sweden," published by the Geological Survey of Sweden, 1925, and in a paper, "Electrical and Electro-Magnetic Prospecting," read by Hans Lundberg at the 1926 annual meeting of the A.I.M.E. In a written discussion on the latter paper, Theodore Zuschlag has made some observations, pub-lished in the Trans. Vol. LXXIV, which has just ap-peared. In this discussion the theories of the Swedish geo-electrical methods are criticized. The statements of Mr. Zuschlag are the reason for, our submitting the following information.1 In developing an art, such as electrical prospecting, the first thing to do, of course, is to make clear the fun-damental principles of electrical prospecting and then apply them to practice. This application cannot, in this case, be made by theoretical calculations only, because Nature is far too complicated to permit of exact theo-retical calculations on the phenomena involved in prac-tical electrical prospecting. Therefore, it is necessary to start with simplified cases, then turn to more and more complicated ones, and, finally, to test the applica-tion of results found, first in the laboratory and then in the field under known conditions.. Only in this way can results of practical value be obtained. This pro-cedure comprises three important parts: theory, the work in the laboratory, and the work in the field. In the papers mentioned above, we have briefly out-lined the work done in developing the Swedish geo-electrical methods, mainly giving some practical results, because these are most important and most likely to interest mining people. Possibly, because the discus-sion of theoretical considerations in our papers has been brief and sketchy, Mr. Zuschlag feels justified in in-ferring that the theories used as the foundation in Swedish electrical prospecting methods are not free from fundamental objections. His fundamental ob-jections are:

Jan 3, 1927

By Heinrich Ries

The fusion-point of clay has usually been considered to be influenced chiefly by the quantity of fluxing impurities which the clay contained. Those clays which contain a high percentage of fluxes, such as ferric oxide, lirne, magnesia, and alkalies, fuse at a low temperature. Aside from the percentage of fluxing-impurities, the size of the grains exerts an important influence. Yet, while this fact has, no doubt, been recognized by many, practically no attempts have been made to prove it by actual experiment, although in the case of fire-clays, Prof. H. O. Hofman has rather disputed it. To illustrate the point more clearly, suppose a clay to be made up of a mixture of very refractory grains, such as kaolinite, and some fusible ones. If this clay be heated, the more easily fusible grains will melt first on the surface, and the softening under heat will gradually extend from the surface of the grain to its center. The larger, therefore, the size of the grain, the longer the time required for the heat to penetrate it. Now, if two samples of clay contain the same volume of flux, but of unequal size, the one containing the smaller-sized grains should fuse first, because the fluxing materials are more evenly and thoroughly distributed through the clay, so that they will more or less surround the refractory grains, which tend to act as a framework and hold up the clay-mass when heated. In order to demonstrate the effect of fineness of grain on the fusibility of clay, several mixtures were made up, consisting of white clay and other minerals. The white clay used was a very refractory type from Georgia, the fusion-point of which lay about cone 35 of the Seger series. The mixtures were formed into small bars 1* inches long, and set on a narrow surface, so that the ends were free to bend as soon as the mass softened. They were burned in a Seger gas-furnace.

Jan 1, 1904

By W. H. Andrews

THE constantly increasing consumption of Portland cement in the State makes the above subject of partlcular interest at this time. The increasing demand is due to the rapid settling of the country and the fact that new uses are being found frequently for the above named commercial article. The industry is one that is bound to grow as the population increases, and this being the case, it may be well ,it this time to consider briefly- the matter of the chemical and physical com-position of proper raw materials. A cement mixture is one that contains approximately 75 per cent. carbonate of lime, 15 per cent. Silica, and 5 to 7 per cent. alumina, and iron oxides; the other elements being magnesium carbonate and small quantities of the rarer elements general associated with limestone deposits. It call be readily seen from the above composition that it is possible to build up this mixture from a number of different materials. First.-A rock high in carbonate of lime can be mixed with clay or shale in such proportions as to bring about the desired composition ; the chief difficulty in the building up of such a mixture is that it is hard to find a clay or shale in which the silica-alumina, ratio lies .between 4 to 1 and 3 to 1 and at the same time shows physical characteristics which will make certain its adaptability to the practical manufacture of Portland cement. Very often clays or shales are found which are right chemically but contain large quantities of grit or free silica. Such clays or shale must be ground to extreme fineness in the mixture in order to make the silica and alumina combine with the lime when the mixture is burned. On the other hand, clays or shales are often found that have the proper physical characteristics but in which the amount of alumina, is too great.

Jan 9, 1913

By W. T. Jr. Thom

IN PREVIOUS classifications of coal, it has been customary to regard moisture eliminated from coal samples between 20° and 100° C. as extraneous matter, rather than as a constituent part of the coal. It seems, however, that the physical character and use properties of the low-rank coals are directly related to the amount of such moisture present, and recent chemical work has shown1 that such coals contain unstable groupings which decompose between 20° C. and temperatures somewhat above 100° C., with the splitting off of moisture. According to this view, the moisture eliminated from air-dried coal below boiling point is similar in all essential respects to moisture eliminated above 100° C., and is produced by analogous reactions; and inasmuch as the moisture given off above 100° C. has always been treated as a constituent of the volatile matter of coal, it would seem that consistent usage would include as a part of the volatile matter all moisture present as an essential component of the coal as it occurs in nature. As a matter of experience, it seems clear that the general physical and chemical characteristics of the low-rank coals are largely determined by or related to the moisture, whether chemically or physically combined, present in air-dried coal; it is also demonstrable by trial that the low-rank coals cannot be satisfactorily classified on a purely chemical basis by using the moisture free form of analysis. The low-rank coals of the western United States include numerous well-defined types, many of which were referred to in a classification proposed by Ashley,2 in which the physical and use properties of the coals were made the primary basis for their systematic grouping. When testing this classification by replotting analyses of these type coals according to the Seyler scheme of classification,3 a satisfactory parallelism between use properties and chemical constitution of the dry coal was found among

Jan 5, 1925

By H. M. Howe

One of the little electric-resistance magnesia crucible-furnaces which I designed for the metallurgical laboratory of the School of Mines of Columbia University is shown, in vertical section, of full natural size, in Fig. 1. The furnace itself consists of two semi-cylinders of magnesia, A A, with a cover of magnesia, B B, and a stopper, C, also of magnesia, which is perforated to admit the leads x, y, of a thermo-electric couple. The furnace is heated by the spiral of platinum wire, D D (entering and departing by the openings I and K), through which a current of any desired strength is passed, bringing it to incandescence, and to ally temperature, not above the melting-point of platinum, which may be desired. The crucible E, actually used in this furnace, is also of magnesia. I have heard of some unsuccessful attempts with furuaces of this general class, and have attributed these failures to the use of siliceous materials for the furnace-walls. Of course such a result is what we should expect, since the silica mould readily be electrolysed by the current, and the resultant silicon would alloy with platinum ; but the little magnesia furnace here clescribed seems to be wholly free from this objection. It has been used in my laboratory for some months, and temperatures, up to 1100° C, hare been developed in it over considerable periods of time—indeed, it has been held near 1400" C. for about two hours—without indication, thus far, of any deterioration of the platinum. In the section shown, F F are a pair of steel disks, bound together, but separated by the inverted thermo-junction, N, of the thermo-electric pyrometer. This arrangement permits the observation and record of retardations in the heating and cooling of F F—in other words, the determinations of the cooling curves of steel—a purpose for which the furnace has been used, thus far, more frequently than in the determination of meltingpoints. For the latter operation, however, it is also suitable.

Jan 1, 1902

By G. L. Craig

COPPER containing a small amount of arsenic has been used extensively abroad, and a number of reports, particularly those by English workers, have indicated that such copper is better suited for certain uses than high-conductivity copper. Inasmuch as a large percentage of the copper fabricated is used for nonelectrical purposes where high conductivity is not at all essential, it has been suggested that arsenical copper might be at least as suitable as high-conductivity copper for many purposes. An investigation spon-sored by the Calumet & Hecla Consolidated Copper Co. at Battelle Memorial Institute was therefore undertaken with the object of determin-ing the effect of small amounts of arsenic (up to 0.75 per cent) on the properties of copper. In this work the effect of arsenic on the basic properties of tough-pitch and of phosphorized copper have been critically studied and many data collected from laboratory experiments which have been supplemented by mill-scale tests. The results of these tests, with coppers of the type referred to, in the annealed condition and after various degrees of reduction, show that the basic properties of copper are not greatly affected by small amounts of arsenic, an increase in strength being observed with increasing arsenic with no corresponding decrease in ductility. It is well known that the evaluation of material for plastic deforma-tion, on the basis of laboratory tests, may not be directly comparable with its performance in commercial operations. In order, therefore, to substantiate the data obtained at the Institute, the cooperation of the Wolverine Tube Co. was obtained for a series of production tests on the fabrication characteristics of phosphorized arsenical copper in the manu-facture of seamless copper tubing. In these tests the behavior of the arsenical coppers was carefully observed in comparison with that of representative types of phosphorized arsenic-free copper, which were fabricated under the same conditions.

Jan 1, 1933

By W. P. Frey

THE briquet plant of the Lehigh Coal and Navigation Co., at Lansford, Pa., has previously been referred to.1 It has passed. the stage of experiment and now rests,, on a foundation practically and financially sound. The purpose of this paper is to explain how success has been attained, and to set standards for the development of hard-coal briquetting which may eliminate future failures. All the conclusions are based on actual results, avoiding speculation and theory. Up to three years ago, the L. C. & N. Co. used coal-tar pitch as a binder in making hard-coal briquets. The plant operated with a monthly output of 300 to 600 tons and was unable to meet its own expenses. Naturally, no one was satisfied, especially as the ideals of a smokeless briquet were still unrealized. Then came the Dutch oil process, introduced in this country by the General Briquetting Co. of New York. This process uses as binder a small percentage of heavy residue of petroleum, which, being liquid, permits great economy of handling; it also did away with the most objectionable fumes of the former briquets. This oil2 is not absolutely smokeless; heating the fresh fuel to red heat liberates some low-volatile hydrocarbons, yielding a white smoke which is not objectionable. On the other hand, this oil adds to the briquet about 7 per cent. of volatile matter, giving the product a heating capacity equal to that of the best free-burning anthracite coal. The average silt used in the manufacture of these boulets averages 16.5 per cent. chemical ash, corresponding to 12,000 B.t.u. per pound of coal. The Hydrolene used as binder runs about 17,500 B.t.u. per pound, and approximately 7 per cent. of it enters into the mixture, hence 12,000 X 0.93 11,160 B.t.u. 17,500 X 0.07 1,125 B.t.u. Total 12,355 B.t.u. per pound of briquets

Jan 1, 1918

By A. S. Koster, G. D. Rieck

X-ray experiments were carried out to show the occurrence of cylindrical texture in drawn tungsten wire. Only a small amount of (110) (110) cylindrical texture could he found in wires of intermediate thickness, i.e., of about 1.5 mm diameter. DRAWN wires of tungsten and other bcc metals like iron and molybdenum show a well-established (110) fiber texture. Now it might be conceivable that in drawing radial stresses remove the randomness of the crystallites around the [110} axis, thus giving a fiber texture of higher symmetry. In the resulting so-called cylindrical textures a specified plane normal coincides with the radius of the wire. Several authors discuss the occurrence of cylindrical textures in bcc metals. ~ieck' found no cylindrical texture in drawn tungsten wires of 165 n diameter. Leber~ states that in tungsten wires of 3 mm diameter a cylindrical {100)(110) texture is developed, which is gradually converted to a normal fiber texture by subsequent drawing. He also reported a definite cylindrical texture at the surface of iron wires. Peck and Thomas3 observed a nonuniform mode of deformation of the grains in transverse sections of heavily drawn tungsten and iron wires. According to Bhandary and cullity4 a swaged iron wire has neither a perfect (110) fiber texture nor a perfect {100}(110) cylindrical texture. It is clear that the concept of cylindrical texture in bcc metals still lacks a firm experimental basis. Leber's eviden~e,~ which seems to be the strongest, rests upon qualitative interpretation of photographs. The appearance of the 110 and 200 lines on the photograph of 3-mm wire, however, can be very well attributed5 to a normal ( 110) fiber texture superimposed on random background; our Fig. 1, giving a Debye-Scherrer diagram of etched tungsten wire of 180 p, is free of cylindrical texture according to all authors, but is quite similar to Leber's diagram. It was therefore decided to use a different method of X-ray texture determination on tungsten wires of diameters where cylindrical textures may be expected.

Jan 1, 1965

By W. H. Andrews

The constantly increasing consumption of Portland cement in the State makes the above subject of particular interest at this time. The increasing demand is due to the rapid settling of the country and the fact that new uses are being found frequently for the above named commercial article. The industry is one that is bound to grow as the population increases, and this being the case it may be well at this time to consider briefly the matter of the chemical and physical composition of proper raw materials. A cement mixture is one that contains approximately 75 per cent, carbonate of lime, 15 per cent. silica, and 5 to 7 per cent. alumina and iron oxides; the other elements being magnesium carbonate and mall quantities of the rarer elements generally associated with limestone deposits. It can be readily seen from the above composition that it is possible to build up this mixture from a number of different materials. First.—A rock high in carbonate of lime can be mixed with clay or shale in such proportions as to bring about the desired composition ; the chief difficulty in the building up of such a mixture is that it is hard to find a clay or shale in which the silica-alumina ratio lies between 4 to 1 and 3 to 1 and at the same time shows physical characteristics which will make certain its adaptability to the practical manufacture of Portland cement. Very often clays or shales are found which are right chemically but contain large quantities of grit or free silica. Such clays or shale must be ground to extreme fineness in the mixture in order to make the silica and alumina combine with the lime when the mixture is burned. On the other hand, clays or hales are often found that have the proper physical characteristics but in which the amount of alumina is too great. Second.—A mixture can be built up of different limestones some of which run above the 75 per cent. requirement and others below;

Jan 1, 1914

AT THE beginning of December, the Lausanne Con-ference was in session. The representatives of the United States declared the American position. The representatives of Russia were received and were heard. The Turks appeared at this conference in the attitude of victors, dictating terms. The British refused to surrender Mosul, and December thus ended with this question unsettled. Early in the month the premiers of the principal powers met in London for the discussion of the German reparations question, the temporary agreement expiring on. Jan. 15, 1923. On Dec. 11 the Conference adjourned without getting anywhere, and at the end of December prospects looked more hopeless than ever. The premiers are to meet again on Jan. 2, 1923. The interruption of the London conference was followed by the intimation of early participation of the United States in European affairs in the practical way of a large loan to Germany. These intimations, ema-nating from Washington, appear to have been in the nature of trial balloons. They showed that the wind was unfavorable, the bankers not considering conditions suitable for the flotation of such a loan. British statisticians are puzzled by the fact that the trade returns of Great Britain show a greater turnover in the volume of goods during the first 11 months of 1922 than in 1920, although the rate of labor employ-ment in 1920 was nearly 100 per cent. and in 1922 only about 86 per cent., with an economic situation admit-tedly so bad as to be alarming. The British Parliament was convened under the premiership of Bonar Law. One of its first acts was confirmation of the constitution of the Irish Free State. Civil war in Ireland continued. Poland, like most of the other countries of Europe, is torn between socialism and conservatism, with the former party at present predominant. Early in December, Gabriel Narutowicz, an engineer but a radical, was elected president. On Dec: 14 he entered office and-on Dec. 16 he was assassinated.

Jan 1, 1923

THE Bergbüchlein and Probierbüchlein occupy a unique position in the literature of mining and metallurgy, for, they are the first printed books on any aspect of the two related professions. The first printed book on any subject has an allure that may not be entirely warranted by the strict historical significance of its contents. Among the books of the first century of printing there are very few that contain information that was new at the time of publication. Much' of what they recorded had been previously circulated in manuscript form. Printed books are nevertheless of great value because they mark the time when the author's words, free from errors-or at least with the same errors-became available to large numbers, of readers, who thus could easily and cheaply acquire a common background for their future work. Moreover, though there is occasionally some doubt as to the exact year of publication'(as in the case of the present works), it is generally easier to date a printed work than a manuscript, and thus to provide a fixed coördinate in history. The Bergbüchlein, "The Little Book on Ores," is the first printed work in the field of mining. It is an introduction to mining geology, which means that it was not addressed to the practicing expert but was intended to rouse the interest of beginners in the various aspects of a future vocation. It touches on the theories of the generation of ores, introduces and defines some of the most frequently encountered technical terms of the profession, and indicates what knowledge and tools are required for successful prospecting and mining. It also describes the ores of the seven most important metals. For those parts that deal with theory the author accepted uncritically the traditional teachings of the alchemists and the astrologers; his hints on where to find promising ores are based partly on superstition; but, there is enough factual,

Jan 1, 1949

By B. S. Tani, R. V. Schablaske, M. G. Chasanov

MEASUREMENTS of the solubility of scandium in liquid cadmium from 349" to 606°C by Chasanov, Hunt, Johnson, and eder' led to the isolation and characterization of the intermetallic compound ScCQ. The solid phase found in equilibrium with a saturated solution of scandium in liquid cadmium above 422°C is ScCQ. The equilibrium solid phase below this temperature has not as yet been characterized. Hexagonal needles of ScCG were isolated from a 5 wt pct Sc alloy which had been ice-quenched from 500°C. Free cadmium was leached away from the intermetallic with saturated ammonium nitrate solution. The concentration of cadmium in successive leaches was followed polarographically and the leaching process was terminated when the rate of cadmium dissolution decreased markedly. Chemical analysis of the intermetallic thus isolated is as follows: 11.5 wt pct Sc and 88.3 wt pct Cd. The composition of ScCQ is 11.8 wt pct Sc and 88.2 wt pct Cd. X-ray diffraction powder photographs of ScCds taken in a 114.6-mm Debye-Scherrer camera with CuKa, radiation can be indexed on the basis of a hexagonal nit cell. Lattice coonstants are a. = 6.330 ± 0.001A to 6.324 i 0.001A and co = 4.853 i 0.001A. The a0 has a slight range with the lower value seemingly associated with the cadmium-rich terminus of the phase. With eight atoms in the unit cell the calculated intermetallic density is 7.54 g per cu cm; the density as determined by a liquid-displacement method is 7.7 g per cu cm. Powder-diffraction data for ScCQ are recorded in Table I. Stoichiometry, symmetry, unit-cell dimensions, and the number of atoms per unit cell indicate the MgsCd (D019) type structure for ScCQ; space group is D,&-P6,/mmc. Atomic coordinates are:

Jan 1, 1964

By Frederic Benard

This paper constitutes a preliminary report on experimental work done to date on the anode-furnace treatment of blister copper containing relatively high percentages of nickel. The investigation has not been completed but results obtained to date are considered of sufficient interest to warrant publication. Blister copper treated by the Ontario Refining Co. originates from the Copper Cliff smelter of The International Nickel Company of Canada, of which the former is a wholly-owned subsidiary. The blister as received contains from 0.50 to 1.50 per cent Ni, and in this respect differs from that treated by other refineries on this continent. During the anode-furnace treatment, only a portion of the nickel content is removed, and of the amount remaining in the anodes a varying percentage is found in the anode slimes. This necessitates a more extensive treatment than ordinary nickel-free material. Sometimes it is necessary to repeat roasting and leaching operations several times before the nickel colltent is low enough to permit the slimes to proceed to the dorè furnace. This, besides increasing treatment charges, causes greater selenium stack losses and involves a longer tie-up of precious-metal values. Therefore this investigation was undertaken with the aim of determining the factors influencing the diversion of nickel into the anode sludge. From experience it was known that by keeping the nickel content of anodes at 0.55 to 0.60 per cent maximum a relatively satisfartory slime resulted. One avenue of attack therefore was developing improved elimination in the anode-furnace treatment so that the anode content mentioned above was not exceeded. Another angle was to improve the solubility, during electrolysis, of the nickel constituent in the anodes, thus decreasing the percentage diverted to slimes. . It may be mentioned here that nickel dissolving electrochemically and entering the electolyte presents no difficulty from a treatment standpoint. Both of these approaches were studied and are discussed separately below.

Jan 1, 1943

By Frederic Benard

THIS paper constitutes a preliminary report on experimental work done to date on the anode-furnace treatment of blister copper containing relatively high percentages of nickel. The investigation has not been completed but results obtained to date are considered of sufficient interest to warrant publication. Blister copper treated by the Ontario Refining Co. originates from the Copper Cliff smelter of The International Nickel Company of Canada, of which the former is a wholly-owned subsidiary. The blister as received contains from 0.50 to 1.50 per cent Ni, and in this respect differs from that treated by other refineries on this continent. During the anode-furnace treatment, only a portion of the nickel content is removed, and of the amount remaining in the anodes a varying percentage is found in the anode slimes. This necessitates a more extensive treatment than ordinary nickel-free material. Sometimes it is necessary to repeat roasting and leaching operations several times before the nickel content is low enough to permit the slimes to proceed to the doré furnace. This, besides increasing treatment charges, causes greater selenium stack losses and involves a longer tie-up of precious-metal values. Therefore this investigation was undertaken with the aim of determining the factors influencing the diversion of nickel into the anode sludge. From experience it was known that by keeping the nickel content of anodes at 0.55 to 0.60 per cent maximum a relatively satisfactory slime resulted. One avenue of attack therefore was developing improved elimination in the anode-furnace treatment so that the anode content mentioned above was not exceeded. Another angle was to improve the solubility, during electrolysis, of the nickel constituent in the anodes, thus decreasing the percentage diverted to slimes. It may be mentioned here that nickel dissolving electrochemically and entering the electolyte presents no difficulty from a treatment standpoint. Both of these approaches were studied and are discussed separately below.

Jan 1, 1938