Search Documents

By Francisco Gil Coury

Ligas Al-Mn-Ce são de grandeinteresse por formaremfases e microestruturasde aplicação promissora, como quasicristais, fase amorfa e ligas cristalinas de alta resistência. Entretanto, pouca atenção foi dada àdeterminação do diagrama de fase desse sistema. Este trabalho apresenta uma avaliação termodinâmica preliminar das fases ternárias Al8Mn4Ce e Al10Mn7Ce2, compostos da região de maior interesse deste sistema:as composições ricas em Al. A avaliação termodinâmica foi feita considerando os dois compostos como fases estequiométricas. A energia livre destas fases foi estimada a partir de dados experimentais obtidos por análise de calorimetria diferencial de varredura, microscopia eletrônica e difração de raios X e as seções isotermas existentes na literatura, empregando ligas obtidas por fusão a arco. Os resultados indicam que foi possível produzir as fases de interesse pela metodologia proposta, e que os parâmetros estimados para a energia livre de ambas as fases permitem reproduzir adequadamente secções isotermas do diagrama ternário em diferentes temperaturas.

Aug 16, 2017

By Jianping Li, Fei Peng, Yunbo Xu, Jiayu Li

In this study, in order to achieve ultra-high strength without reducing plasticity, a novel heat treatment involving a pre-quenching process prior to conventional intercritical annealing (P-IDP) was proposed in a low carbon low alloy DP steel. It revealed that abundant fraction of banded structure was observed after conventional intercritical heat treatment (IDP) due to the inheritance of cold rolling deformation. However, the banded structure in novel heat treatment was eliminated significantly, whilst the refined microstructure was relatively more homogeneous with ultrafine ferrite grains. Moreover, obvious chain-networked martensite grains along the ferrite grain boundaries were obtained. The optimum mechanical properties with ultimate strength of 1238 MPa, total elongation of 17%, product of strength and elongation (PSE) of 21GPa% were obtained by P-IDP treatment, which was much higher than the values reported with similar composition. As to pre-quenching treatment, all of grain refinement, homogeneous distribution of martensite islands and precipitated strengthening of microalloyed carbides were beneficial to improve the final strength and ductility.

Oct 1, 2019

By Weslei Viana Gabriel

Por meio do uso de técnicas de modelamento físico e matemático, caracterizou-se o fluxo de líquido, no interior de um molde de beam blank, quando alimentado por apenas uma válvula submersa constituída por três portas de saída cilíndricas e espaçadas de 120°. Verificou-se que o fluxo do jato de líquido que atravessa a alma se espalha ao longo de toda a superfície do flange antes de se recircular na região central do molde. Através da técnica de injeção de traçador e análise do perfil de velocidade, percebe-se que os jatos direcionados para as quinas do flange recirculam rapidamente e, por isto, se espalham numa pequena região. Este tipo de válvula se caracteriza também por ter uma maior intensidade de oscilação da superfície do que a válvula do tipo tubular. Foram realizados testes para simular a taxa de remoção de inclusões. Os dados obtidos mostram que esta válvula é mais eficiente na limpidez do aço do que uma válvula tubular simples.

Oct 30, 2017

By Vinícius Carvalho Teles

Durante a estampagem, ocorre o desgaste na superfície da ferramenta devido ao deslizamento entre a ferramenta e a peça. A manutenção das ferramentas de conformação envolve o polimento das bordas ou, em casos mais severos, a substituição da mesma é necessário. Ensaios de deslizamento alternado em revestimentos CrAlSiN depositados sobre aço ferramenta evidenciaram mecanismos de desgaste abrasivo devido a partículas de desgaste anteriores. O objetivo deste trabalho foi investigar a resistência a abrasão destes revestimentos, onde variou-se a topografia do substrato e arquitetura do revestimento, a composição química e a espessura. As propriedades mecânicas destes revestimentos foram avaliadas utilizando ensaios de esclerometria com carga progressiva e microdureza Knoop. A resistência à abrasão foi avaliada utilizado testes de microabrasão com partículas abrasivas de SiC. Os resultados mostraram que não houve diferença nas taxas de desgaste entre as duas arquiteturas. Maiores taxas de desgaste foram obtidas ao diminuir o teor de AlSiN na superfície e ao diminuir a espessura. Também foi observado uma relação entre as taxas de desgaste e o produto da carga crítica e a microdureza.

Aug 16, 2017

By Alessandro Pigani

Over the last 25 years the thin slab casting and rolling process has been gaining a major market share in the production of hot rolled strip, progressively eroding the areas previously of exclusive domain of conventional mills. This is mainly thanks to the competitiveness of the process over conventional ones, and to the growing ability of this technology to cover the majority of market niches, well beyond the boundaries of the commodity market. After having significantly contributed to the continuous expansion of this production mode and after an extensive campaign of theoretical research and physical testing in reference plants, Danieli has progressively developed over the years a new generation of thin slab casting and rolling layout, marking a new phase in the evolution of this process. The new step-ahead is epitomized by the name QSP-DUE. This configuration belongs to the Quality Strip Production (QSP) family, which is Danieli’s strip-quality-oriented thin slab based plants. The innovative features of the process are embodied in the acronym DUE, which stands for Danieli Universal Endless (Danieli patented technology – US patent n. 8087449, January 3rd, 2012). What makes this new concept different is the ability of “universal” rolling modes thanks to the fact that, now, within one single plant it is possible to perform coil-to-coil, semi-endless and endless rolling modes, making this plant a major technology innovation compared to the previous generation.

Aug 16, 2017

By Ian James McDonald

Each year, approximately 400 million tons of blast furnace slag is produced worldwide with a tapping temperature of around 1,500°C. It is normally used as a substitute for cement clinker or as an aggregate material in road construction. Currently, the slag is granulated in wet-granulation plants using large volumes of water and to date, it has not been possible to utilise the remnant heat energy of the molten slag, which amounts to approximately 1.8 GJ of energy per ton. However, in an R&D project currently underway led by Primetals Technolgies and industrial partners, a new dry atomising technology is being investigated to use air to cool molten slag and recover the lost heat energy. The resultant pelletised slag fulfils the same criteria as wet-granulated slag for use in the cement industry. Phase 1 of the project has now been completed where a technical plant was set up at the University of Leoben in 2012. A series of dry-slag granulation campaigns were carried out using remelted blast furnace slag. The elevated offgas temperatures and the quality of the slag product as verified by the FEhS Building Material Institute have shown the process suitability as an industrial application and the decision was taken to escalate the project from large laboratory scale to a full size pilot plant. The phase 2 development of this plant is now underway and is scheduled for installation at the site of an industrial partner in early 2016 where full slag flow will be fed directly to the plant from Blast Furnace ‘slag runners. This paper will show the development path taken to date and the planned route to our goal in 2016 of being the first to industrialise the ‘game changing’ process of dry Slag Granulation with Heat Recovery from the slag.

Aug 16, 2017

By Ana Maria Guilherme Bailon

A coesão entre os grãos de ferro em pelotas queimadas é afetada por mecanismos difusionais dependentes de tempo e temperatura de sinterização e do tipo de elementos presentes na escória. Óxidos presentes nos insumos e no minério exercem influência significativa no processo de difusão das partículas de ferro e na formação de escória, composta principalmente por CaO, SiO2, Al2O3 e MgO. O estudo da influência da escória na microestrutura de pelotas de minério de ferro permite um maior entendimento das principais características relacionadas às fases formadas, que afetarão diretamente sua resistência física e comportamento metalúrgico. Neste trabalho abordamos a influência da variação nos teores de CaO e SiO2 na estrutura das pelotas com o objetivo de verificar a interferência desses compostos na diminuição da energia livre superficial e crescimento de grão bem como na distribuição de porosidade e formação de fases como hematita, sílicatos, ferritos e, eventualmente, a magnetita. Para tal avaliação, pelotas com diferentes teores de escória passaram por caracterização química, análises em Microscópio Óptico e análises em Microscópio Eletrônico de Varredura.

Aug 1, 2018

By José Aparecido Pereira

The innovative methodology developed by the author allows the elaboration of an Angle Roll Pass Design based on the practical observations of the rolling process and applies mathematical criteria, using the Ekelund´s formula supported by Advanced Excel tools (Reach Goal, PROCV-PROCH, Macros) and AutoCad. The first step is the definition of the number of stands, roll dimensions, gear boxes reduction, initial stock, average reductions, spread factors, finishing speed and type of grooves. For each pass are calculated: bite angle, spread, section reduction, lost and gain of temperature, separating force, speed, torque and motor power. After these calculations and checking of the parameters, the program calculates the dimensions of the passes transforming the flat passes into shaped ones. With these dimensions it is possible to draw the grooves using AutoCad and check section reductions. This methodology was already used for the development of a new project and also to check the parameters of existing ones, with comparison of the results and has shown to be reliable in real and tested projects. It is an innovative process that is not available in known literature.

Oct 1, 2019

By Sebastien Flament

More and more Hot Strip Mills are facing defects on their products that lead to a rejection of complete product batches by their customers. Several of those defects are induced by excessive work roll degradation. This paper is focussed on the understanding of work roll corrosion and oxidation mechanisms in a hot strip mill. Several laboratory trials (Hot rolling simulator, cyclic oxidation) have highlighted important factors influencing corrosion of work rolls as well as helping the understandings of oxidation of a work roll in the roll bite and along the roll circumference in a stand. The attention is focussed on several elements present in water used in HSM for direct roll cooling (e.g. chloride, bactericides, sulphates, phosphates) and their effect on roll surface degradation. The second part of this paper is focused on the understanding of work roll oxidation along the roll circumference. The effects of roll composition, roll temperature, water composition and water temperature have been studied in order to understand the oxidation/corrosion mechanisms in a HSM.

Aug 16, 2017

By Andrea Pezza

The steel market is experiencing a difficult conjuncture: on the one hand steel producers minimize their investments while optimizing their over- production, on the other hand suppliers reduce their internal human resources and capacity in order to overcome the instability of the new era. A return to the steel production levels of the past is not expected in the short term. Research, development and plant concept optimization is one recipe to drive the future of the steel business. This article describes a new concept for a VOD plant developed as a result of thorough investigation and assessment of all possible solutions. A joint and tight cooperation with the final customer was necessary to reaching important results. This article consists of the contributions from the plant suppliers in terms of their experience and feedback, as well as the final user’s. The final customer, voestalpine Giesserei Linz GmbH, and the plant supplier, Primetals Technologies, are both worldwide players and highly focused on reaching best quality and innovation.

Oct 30, 2017

By Alisson Rodrigo dos Santos

O presente trabalho objetiva analisar a viabilidade técnica de recuperar parte do pó de balão, composto por finos de carvão e hematita, submetido primeiramente a tratamento termoquímico e posteriormente a campo magnético uniforme. Foram analisadas amostras oriundas de pó de balão de alto forno funcionando com carvão mineral e alto forno com carvão vegetal. Os finos de carvão, recuperados na separação magnética, podem ser utilizados na sinterização, pelotização e até mesmo reinjetados nas ventaneiras. Essa reutilização tem um efeito muito importante, pois cada tonelada de fino carregado pela ventaneira corresponde a uma economia de carvão que não será carregado pelo topo, deixando mais volume útil livre para a carga de minério. O pó de balão foi submetido a um processo de redução da hematita em magnetita, em atmosfera adequada para a preservação de carbono, a fim de aumentar a susceptibilidade magnética e permitir a separação magnética. Os finos de minério residuais da recuperação dos finos de carvão não são perdidos, podem ser utilizados na fabricação de briquetes ou reutilizado na sinterização e pelotização. Após a redução, o material foi submetido à separação magnética, mostrando-se assim viável tecnicamente a separação e reaproveitamento dos finos de carvão e minério.

Oct 30, 2017

By Franco de Castro Bubani

Cu-base alloys (Cu-Zn-Al, Cu-Al-Be, Cu-Al-Ni), depending on their composition, have martensitic transformations that can be thermally or mechanically induced between a metastable structure called austenite and one or more metastable structures called martensites. In single crystals, depending on the specific composition of the alloy and the crystallographic orientation of the tensile axis, martensite-martensite transformations can be mechanically induced. The hysteresis associated to these martensite-martensite transitions is usually much greater than the one associated to the austenite-martensite transformation. Thus, martensite-martensite transitions are potential candidates for energy dissipation in a mechanical damper. Possible applications that would benefit from high hysteresis include seismic damping devices, dampers for satellites and the aerospace industry, defense and others. We present pseudoelastic cycling results of alloys submitted to different thermal treatments. Our conclusions highlight the fact that, under certain conditions, Cu-base alloys deliver better damping performance than commercially available SMAs and even the new Fe-base SMAs.

Aug 7, 2018

By Thiago Pires Nagasima

O refino de grão da estrutura bruta de solidificação da liga Cu-30%Zn (latão 70/30) a partir de adições de P e Zr ao banho líquido foi investigado utilizando-se microscopia óptica, microscopia eletrônica e microanálises. Foram conduzidas medidas de tamanho médio de grão pelos métodos planimétrico e do intercepto linear e foram realizadas microanálises por espectroscopia de dispersão de energia (EDS) e de comprimento de onda (WDS). Nas amostras obtidas observa-se que, quando são adicionados P e Zr, sempre ocorre a diminuição do tamanho médio de grão em relação àquele das amostras onde apenas P é adicionado. O menor tamanho médio (? 200 ?m) ocorre para um teor de 0,16% de Zr. O refino de grão coincide com a formação de precipitados geralmente facetados, contendo Zr e P em uma proporção equivalente à da fase ZrP. Sugere-se que as adições causaram a formação de partículas sólidas de ZrP, sobre as quais ocorreu a nucleação heterogênea de grãos da fase Cu-?, resultando no refino de grão.

Oct 30, 2017

By Alexandre Rodizio Bento

Os acidentes de trabalho estão cada vez mais presentes em indústrias de vários segmentos, inclusive no setor automotivo. Devido ao trabalho no chão de fábrica deste setor utilizar interferência humana em alguns processos e operações, onde o trabalhador compartilha o ambiente produtivo com máquinas automatizadas. Estas máquinas podem causar graves lesões temporárias ou permanentes no trabalhador, podendo chegar até a morte. Neste cenário, este trabalho apresenta um estudo da implantação da pirâmide de Heinrich como forma de informar e prevenir acidentes na indústria automotiva. É detalhado o processo de implantação da pirâmide na linha de produção. Esta implantação contribui na prevenção de acidentes, gera alertas de possíveis riscos, comportamentos inseguros e incidentes. Os resultados desta implementação acabam aumentando a segurança no ambiente de trabalho, reduz custo com acidentes dentro da indústria, que permite investir cada vez mais em métodos para prevenir e gerar um ambiente de trabalho livre de acidentes no setor automotivo.

Aug 8, 2018

By Mario González Ramírez

The safe transport of sour gas requires steels with enhanced hydrogen induced cracking (HIC) resistance. Centerline segregation bands of high hardness microconstituents and non-metallic inclusions are the heterogeneities usually linked to HIC failures in pipeline steels. Full-scale production heats of a new low Mn, Nb microalloyed steel were produced by different steel mills aiming at the application in sour gas environments. The new alloy design provides both effective strengthening and control of sulphide inclusions. Coil microstructure consisted of fine grained ferrite with a small volume fraction of uniformly dispersed eutectoid aggregates. Most importantly the microstructure was uniform in both the longitudinal and transverse directions and exhibited exceptional consistency. Samples from this steel were submitted to HIC testing according to NACE standards TM0284-2003 without any sign of cracking. The results, so far, confirm that this new alloy design provides the unique opportunity to economically produce a high strength pipe steel grade with improved sour service resistance for the linepipe industry.

Aug 8, 2018

By Luca Tommasi

Danieli complemented its wide range of production plants for the iron and steel industry with a further step upstream into iron ore pelletizing and beneficiation. Danieli has engineered and constructed a state of the art and fully automated pilot plant facility – pot grate and sinter box – at Altos Hornos de Mexico S.A. (AHMSA) Pelletizing Plant, Monclova, Mexico. Installation and commissioning were completed in October 2009. Key features of the pot grate include the avoidance of the need for operator intervention during the test, automatic system preheat, absence of dead time, heat recuperation system with an air/air heat exchanger, oxygen control in preheating and firing with zirconia oxygen analyzer, possibility to test deep beds up to 625 mm. A series of projects have been accomplished by AHMSA availing of the pot grate facility with the aim to enhance pellet plant productivity and to reduce operating costs. The results obtained by use of Danieli pot grate combined with the experience and skill of plant operators has shown significant technical and economical benefits thus fully justifying the initial investment made by AHMSA and confirming the importance of having an in-house testing facility in order to optimize industrial plant operations.

Aug 16, 2017

By Afonso Garcez de Azevedo

As primeiras argamassas utilizadas em construções pelo homem continham em sua composição, materiais argilosos. Porém, por ser um material com muitas cargas elétricas livres, as argilas reagem constantemente com a água, ocasionando grande variação linear que acaba causando fissuração nas argamassas feitas com esse material. Assim, para solucionar esse problema, passou-se a utilizar cal hidratada no lugar dos materiais argilosos. Dessa maneira, mesmo não sendo composta por argila, a argamassa mantém sua trabalhabilidade. Nesse cenário, o presente trabalho teve como objetivo balancear estequiometricamente a cal hidratada e as argilas estudadas, para utilizar essas quantidades em argamassas para revestimento, barateando assim o material. Para encontrar esse balanceamento estequiométrico calculou-se a massa molar para um mol de cal hidratada e para um mol teórico de argila. Assim foram estipuladas algumas proporções possíveis de balanceamento da equação de reação cal+argila. Além disso, foram confeccionados corpos de prova, variando as quantidades de argila e cal, para realização de ensaios de capilaridade, a fim de comprovar a eficácia dos resultados encontrados no balanceamento teórico.

Oct 30, 2017

By Fernando Nunes da Silva

Wear mechanisms of materials that constitute the equipments and operating parts in the pre-salt area during the production of petroleum and gas can include corrosion, corrosion-cavitation and corrosion-cavitation-erosion. In the laboratory, it is realizable, but at times it is inaccurate to reproduce or visualize some of these mechanisms due to the real complexities caused by hydrodynamic flows, and the physico-chemical and mechanical non-linearities. The main objective of this work was to study coupons of low carbon steel under laboratory conditions, such as corrosive, cavitative-corrosive (CO2) and corrosive-erosive (CO2 + SiO2), in a stirring aqueous saline solution (0 and 5.0 m/s) at two levels of temperature, with bubbling of gas (5.0 L/min) and contaminated with or without (2.5 % mass), by solids particles of SiO2. The surface of the coupons subjected to upstream flow (0° in a cylindrical generatrix of coupon), and downstream flows (180º) were analyzed by profilometry. The measurements of roughness and waviness of all coupons were statistically analysed using Statgraphics® Centurion XVI, at a confidence level of 95% and significant differences observed in some matrices were discussed.

Jul 31, 2018

By Vitor Orlando Ferreira

The efficiency of an apparatus which uses a forced lubrication system, as well as the useful life of its components, is strongly related to the degree of contamination of lubricating oil. The presence of contaminants and the degradation of the oil itself cause it to release substances that fouling of the wall of the pipes. The cleaning and dialysis of the oil pipes, besides prolonging the life of the lubricant reduces wear of the components. There are several methods of cleaning in pipes, the problem is that some have abrasive characteristics, which could damage some types pipes. Among the non-abrasive methods stand the Flushing and Air scouring. Flushing uses the lubricating oil which circulates in temperatures alternating and high speeds, for generating turbulence to perform washing. The Air scouring method uses oil and filtered compressed air, injected into pipe, to generating higher flow, causing the power supply unit with fluid can work with lower power consumption and higher speeds, removing fouling of the pipe. The objective of this research is to evaluate the Reynolds number to correlate with the efficiency of cleaning the pipe. The method applied was the Air scouring and it was verified that the qualitative effects may occur when compared to Flushing. After testing, it was found that the chosen method brings significant changes in flow, and this flow regime varies considerably increasing the Reynolds number.

Jul 31, 2018

By Fernando Hernández Polanco

Transportation and handling metals and alloys from mills to consumption factories as well as dosing in conventional processes with ingots and scrap has always been considered a complicated activity with high operating costs. Several manufacturers of ferroalloys willing to solve these problems have chosen an alternative for their products that can be used to secure, during transport and dosage in the processes to making special steels, with more efficient consumption of ferroalloys. The trend for the production and sale of ferroalloys is to provide the product in the form of granules packed in bags or in bulk. In this paper we will show you how the granulation process was developed and rapidly adopted the ferroalloys industry as an effective solution to reduce operating costs, create cleaner and safer working environments.

Oct 30, 2017