Search Documents

By Lyman G. J

Dense medium drum separator efficiency was analysed at two Western Australian iron ore concentrators. Efficiency data had hitherto been difficult to accumulate due to the high cost of analysing representative, and therefore large, coarse ore samples. To overcome this problem, recoverable density tracers, which are in effect artificial mineral and gangue, were manufactured in three different sizes (15 mm, 30 mm and 60 mm). Their use enabled partition curves to be studied within one hour of conducting a test: separation densities were generally lower than the feed medium density for all three sizes of density tracer. For a given set of operating conditions, the smaller tracers had lower separation densities and larger ecart probab/es than the large tracers. These phenomena are explained with the aid of a conceptual model of a drum separator, which assumes that the feed ore plunges to the bottom of the drum upon introduction. Particle rising velocities are, therefore, process determining.Medium rheology was altered by adjusting the proportion of solids in the pulp. This was accomplished by changing both the pulp density and ferrosilicon/magnetite ratio. Higher solids volume fractions invariably caused a decrease in separation densities and an increase in ecart probables, most markedly for the smaller tracers. A similar response was observed when feed tonnages were raised.An explanation for these phenomena is sought in the discussion which also suggests means of improving drum separator efficiency.

Jan 1, 1987

By Daniel M. Flanagan

"Editor’s note: Each year, Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue, all the while doing their own jobs. Thank you to the industrial minerals annual review editor, to the Industrial Minerals & Aggregates Division technical committee chair and vice chairs, and to the authors of the individual commodity profiles. Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor.Joe Garska, member SME, of Imerys, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include:• Hyunjung Kim, member SME, of Chonbuk National University, agricultural materials.• Xihui Lin, member SME, of Kemira, ceramics and refractory materials.• Nikhil Gupta, member SME, of Virginia Tech, chemical raw materials.• Adam Rodriquez, member SME, of Penn State, construction aggregates.• LeDeana Roberts, member SME, of Imerys, fillers and pigments.• Harsha Kolla, member SME, of ChemEOR, sorbents, filters and process aids.• Edgar Blanco, member SME, of FLSmidth, specialty minerals.Their help makes possible this July industrial minerals issue. On behalf of ME readers, the editors thank them.During the past 25 years, U.S. ball clay production (the quantity sold or used by domestic producers) increased from 788 kt (869,000 st) in 1990 to an alltime high of 1.31 Mt (1.44 million st) in 2003 (Fig. 1). Housing construction within the United States, a leading market for ball clay-based ceramics and sanitaryware, began to decline in 2005, which resulted in a considerable decrease in sales of ball clay that continued through the 2008-2009 economic recession. After bottoming out at 831 kt (916,000 st) in 2009, ball clay production steadily increased through 2015 (Fig. 1). Estimated sales in 2015 were 36 percent higher than those in 1990 and 18 percent lower than those in 2003.Four companies (H.C. Spinks Clay Co., Imerys S.A., Old Hickory Clay Co., and Unimin Corp.), mined ball clay in five states during 2015. An estimated 1.7 Mt (1.18 million st) of ball clay valued at an estimated $47.5 million was sold or used by U.S. producers, a 4-percent increase from 1.03 Mt (1.14 million st) valued at $45.2 million in 2014. Approximately 65 percent of total ball clay production was air-float, 25 percent was crude or shredded and 10 percent was water-slurried"

Jul 1, 2016

By C. C. Popoff

The growth of the aluminum-smelting industry in the Pacific Northwest, resulting from national defense requirements, emphasized a need for local sources of alumina to supplement the alumina production shipped from the East. Because supplies of foreign bauxite were being interrupted and our domestic bauxite reserves were inadequate, it was necessary to expedite the investigation of other possible sources of alumina during World War II. A program of investigation of high-alumina clay deposits in the Northwest was carried out jointly by the Federal Geological Survey and the Federal Bureau of Mines. As part of this program the Cowlitz clay deposits near Castle Rock, Wash., were explored by the Bureau of Mines in 1942-43. These deposits are near railroads, tide-water, and Bonneville Power Administration lines and within 22 to 100 miles of 4 aluminum-reduction plants.

Jan 1, 1955

By R. A. Hatch

This report summarizes the results of nearly 8 years research on and production of synthetic mica at the Electrotechnical Experiment Station of the Federal Bureau of Mines, Norris, Tenn. This program was undertaken at the request of the United States Department of the Navy and was financed mostly by the Army Signal Corps and the Navy Bureau of Ships through a contract with the Office of Naval Research, The original objectives included fundamental studies of fluor-phlogupite and other fluorine-micas and production of synthetic mica sheets on a pilot-plant scale. The first 3 years of this project were devoted mainly to a search for practical solutions of the many problems involved in designing and constructing a pilot plant for crystallizing fluor-phlogopite mica. The first and most urgent need was a suitable container for the corrosive mica melt. After extensive study, it was concluded that platinum, graphite, high-silica fire clay, and silicon carbide were the most promising refractories for crucibles; but none was perfect. Silicon car¬bide seemed to have the better combination of qualities, combining good corrosion resistance with oxidation resistance.

Jan 1, 1957

The accompanying supply/demand flow diagrams and 10-year tables for mineral and fuel commodities present essential data required by government, industry, and others to formulate policies and programs that can help assure an adequate and continuing supply of mineral raw materials. The 10-year data base terminates with 1973 figures because adequate world information was not available beyond that date. Moreover, 1974 was an anomalous year with respect to prices, supply, and demand for many commodities. The selected mineral supply/demand tables and flow diagrams comprise but one "output" from the massive body of "information and data collected and com-piled by the Bureau of Mines on a continuing basis covering mineral production consumption, prices, shipments, imports, exports, and stocks, as well as industry activities in all States and abroad.

Jan 1, 1975

By H. W. Gillett, G. M. JAMES

In its work on mineral wastes the Bureau of Mines is studying losses in the melting of nonferrous metals and alloys. The greatest of these losses is that of zinc through volatilization in brass melting, but another and considerable loss is that of aluminum and its alloys in the melting of finely divided material. In order to get some idea of the magnitude of the loss in melting aluminum scrap and to find out what methods of melting were used information was gathered in regard to present practice; also experiments were conducted to obtain some data on the relative merits of different methods. As the experiments could be made on a laboratory scale only, they were not expected to solve the problem entirely, the object in making them being rather-by indicating which methods were of greater promise-to narrow the field over which largescale tests and comparisons need be made by those commercially nterested in the problem of melting scrap aluminum.

Jan 1, 1916

By B. M. O'Harra

Zinc smelting is frequently termed a ba.ckward art. The term is hardly true, for great progress has been made in recent years in the design and in the thermal efficiency of the retort furnace, in the quality of retorts, in the recovery of zinc, and in the ability to treat more impure and complex ores. The fact remains, however, that the peculiar physical and chemical properties of zinc have delayed such immense advances-large smelting units, high recovery, lowunit costs, and ability to treat low-grade ores-as have been made in the metallurgy of lead and copper. In current retort-smelting practice, the ores, if carbonates, are calcined to remove carbon dioxide; or, if sulphides, are roasted to remove sulphur. The sulphur must be eliminated as completely as possible, usually to less than 1 per cent. This means that the roast must be continued for a long time at a high temperature, with resulting high cost and small capacity per furnace. The roasted ore is mixed with about 50 per cent of its weight of reducer, which may be fine coke, anthracite, or nonbituminous coal. This mixture is charged into horizontal fire-clay retorts. The retorts used in this country are about 8 inches in internal diameter by 4 feet in length and hold 50 or 60 pou~ds of ore. The diameter of the retort is limited by the tirrie required for the heat to penetrate to the center of the charge; the length by the strength of the retort, which at the high temperature employed can not support the weight of the charge if the span is more than about 50 inches. The retorts are heated externally by coal, natural gas, qr ·producer gas to a temperature of 1,200° C. or more. The zinc oxide is reduced to zinc, which is volatile at this temperature, and passes into a conical fire-clay condenser. attached to one end of the retort, where it conde_nses to liquid zinc and is removed. Twenty-four hours are required for distillation, and because of the low heat conductivity of the retort walls 11.nd of the ore charge itself, the heat efficiency even of the most modern regenerative furnacei;; is only about 12 per cent. The retorts have a short life, 30 to 6Q days, at the high temperature required-; zinc losses are heavy, usually 10 per cent or more; and the proportion of impurities in the retort charge must be carefully controlled to prevent the rapid corrosion of retorts. For these reasons, much work has been done in an e:ff ort to, find cheaper and more efficient methods o.f recovering zinc from its ores. Various methods have been proposed for smelting in the blast furnace. Some of these contemplated the production of zinc vapor and its condensation to liquid; others attempted to produce liquid zinc directly by smelting under pressure. It is now realized that fundamental difficulties render these proposals impracticable. The electric furnace for smelting offers obvious advantages in the way of the efficient utilization of energy, large units, easy attainment of high temperatures, and the possibility of treating complex ores. E. H. and A. H. Cowles first suggested a design for an electric furnace for the reduction of zinc ores and patented their process in 1885. Their attention was soon directed to other uses for their furnace and nothing further of importance was done in the electric smelting of zinc until about 1900. Several investigators then started work upon various processes and had more or less success. The chief difficulty they encountered was the impossibility of obtaining more, than a small amount of the zinc as liquid metal because most of the zinc vapor condensed as blue powder. Interest in the electrothermic metallurgy of zinc increased, many patents on processes and furnace design were taken out, and the literature on the subject grew, until in 1914 and 1915 the problem seemed to be approaching solution. About this time the hydrometallurgy of zinc, the development of which had been lagging somewhat behind that of the electrothermic metallurgy, sprang into the limelight and a commercial process was soon perfected. This rapid development, perhaps aided by the war premium on the high-grade spelter produced by electrolytic deposition, distracted attention from electric smelting to some extent, though progress continued. With the perfection and standardization of the electrolytic process has come a better realization of its limitations, especially the necessity for large-scale operation ·and the difficulty of obtaining high extraction. Because of these limitations the electrothermic metallurgy of zinc still has a field of its own and in fac-t promises to become a strong competitor of both hydrometallurgy and retort smelting except under conditions highly favorable to the latter methods. Because of the imperfections of the retort and electrolytic processes and the promise that the electric furnace offers in overcoming these imperfections, the. United States Bureau of Mines, in cooperation with the Missouri School of Mines and Metallurgy, has undertaken a study of the electrothermic metallurgy of zinc.

Jan 1, 1923

By Haskiel R. Shell

While the original purpose of the Bureau of Mines work on fluorine micas was to synthesize large single crystals or film suitable to replace natural muscovite or phlogopite, the objective was broadened to include development of the many possible fluorine micas as a class of new, unique materials. Several methods were developed for the synthesis of the fluorine micas at atmospheric pressure: Solid state reaction, melting in crucibles, internal resistance electric melting, and arc resistance electric melting. The latter two methods are now med commercially. A variety of fluoromicas were synthesized by isomorphic substitution including disilicic, trisilicic, and tetrasilicic. Fluorophlogopite, KMg3AlSi3O10F2, is the fluoromica most widely used. While most of the fluoromicas are completely stable to water, many water-swelling fluoromicas and fluoromontmorrilonoids were synthesized. Single crystals or film of the fluorine micas were grown to 2 inches or more by a number of methods, but none has as yet proved economical. In the report, detailed data and descriptions are given on compositions, syntheses, products, and uses, and on the properties including physical, dielectric, chemical, X-ray, optical, and structural.

Jan 1, 1969

By Edward L. McHugh

The appraisal of mineral resources of the Challis National Forest, Idaho, by the U.S. Bureau of Mines, was made so that the mineral resources of the forest could be appropriately considered in land use planning. Information from this study is intended to help the U.S. Forest Service to incorporate mineral resource data into forest plans. The study was done in conjunction with the U.S. Geological Survey, which released a companion report on the geology and mineral potential of the Challis National Forest in 1989. Mineral development activity in and under the Challis National Forest has been of great economic significance to Idaho and the United States. Since the 1960's, mines within the forest have produced mineral commodities worth more than $590 million A current (1989) commodity prices. Identified mineral resources have a gross value of about $2 billion at current prices, including 8 strategic or critical minerals. The U.S. Bureau of Mines study identified and described 723 active and inactive mineral properties within the forest. Mineral properties with identified resources were evaluated to determine their economic significance, and an assessment was made of the feasibility of mineral development. Of the 2,516,191 acres in the Challis National Forest, about 390,000 acres were classified as having mining development interest commercially important mineral production, mainly of molybdenum, gold, and silver from the Challis National Forest is likely for the foreseeable future.

Jan 1, 1991

The realization that there is a limit to our supply of domestic mineral and fuel resources, which have been taken for granted until recently, has stimulated the need for conservation and optimum utilization of the Nation's minerals, metals, and fuels-resources critical to our national economy. The mission of the Bureau of Mines is to develop new technology, improve existing technology, and disseminate information related to mineral resources and industries. Fulfilling the mission is necessary to insure a continuing, adequate supply of minerals and alternative supplies of energy from reliable sources at the lowest possible cost to society and the environment. Established in 1910, the Bureau of Mines under the Department of the Interior is the Federal Government's primary research arm in the mineral field. Since the transfer of the fossil fuels portion of the energy research program to the newly organized Energy Research and Development Administration (ERDA) in fiscal year 1975, Bureau research has been concentrated on increasing mineral production, decreasing energy usage through more efficient processing, and decreasing material losses caused by corrosion. Concurrently, research is being addressed to improved coal-preparation techniques, especially to expanding utilization of low-grade coals and coals difficult to beneficiate, which are essential for reducing the need for petroleum and natural gas supplies and for redirecting our energy consumption. Fluctuations in the availability of foreign sources of minerals, metals, and fuels due to political and economic variability among nations have necessitated intensified investigation into coal mining, uranium-ore processing, and geothermal energy sources-three alternatives that can help to alleviate the dependence of the United States on foreign sources of energy.

Jan 1, 1975

When the Organic Act of 1910 established the Bureau of Mines within the Department of the Interior, the Bureau's programs involved only health and safety research and, education, and fuels testing. As the Federal Government's primary agency for research in minerals, the Bureau has expanded its scientific and technological investigations to mining, processing mineral substances, eliminating occupational health and safety hazards in the mineral industries, economic development, and resource conservation. Today, Bureau activities cover a broad spectrum of programs for meeting the diverse (and sometimes conflicting) needs of mineral industries, government, and the public. In the 1960's, the Bureau initiated programs to resolve environmental problems associated with past mining and mineral processing. In the 1970's, the energy crisis raised the national consciousness concerning our limited supplies of domestic mineral and fuel resources. Dependence on foreign sources of raw materials critical to our national economy and competition from other countries for these world supplies stimulated the need to conserve and use with intelligence the Nation's minerals, metals, and fuels.1

Jan 1, 1977

By Edward Skolnik

The concept of using fluid dense media to separate heavy ore constituents from the lighter gangue dates back to 1858, when it was patented by Sir Henry Bessemer. Its use in coal did not begin until after 1917, however, when Chance invented a process (which bears his name) in which lighter coal floats in a suspension of fine sand in water while heavier refuse sinks. Conklin used fine magnetite in suspension as a medium for floating anthracite in 1922, DuPont designed a plant employing organic liquids in 1936, and Belknap used a solution of calcium chloride (which Bessemer had suggested, among other media) in 1937. Separation of magnetic media by magnetic separators from the suspensions in which they were carried was introduced in a Butler Brothers ore concentrator pilot plant in 1937. The media first used were crushed steel and various grades of ferrosilicon. Since 1940, when American Cyanamid used magnetic separators to recover and clean magnetite in a coal washing circuit, virtually all heavy medium circuits have been of that type. As long as static baths are employed, as they are in the processes above, coal smaller than 9.5 mm or 6.4 mm cannot be cleaned economically in heavy medium. The settling velocities of the fine material are very low, and consequently the time required to separate the lighter coal from the heavier refuse becomes excessive. In addition, stray currents in the vessel and the upward velocities induced to keep media solids in suspension affect the finer solids to the degree that physical size becomes a more important factor than specific gravity.

Jan 8, 1980

By Charles L. Kusik

A study was conducted for the Bureau of Mines, U.S. Department of the Interior, to provide information which will lead to an increase in the recycling of mineral materials, in order to help conserve the Nation's mineral resources. Data were collected on energy requirements to recycle prompt industrial and obsolete scrap for nine metal commodities: Iron and steel, aluminum, copper, zinc, lead, stainless steel, titanium, tin, and nickel and nickel alloys. Major process routes for recycling were considered, starting from the first collection point through scrap preparation, transportation, smelting and/or refining to the molten metal, ingot, or other semi- finished form approximately equivalent to a primary metal of a similar composition. Available data for 1976 were collected on the amounts of each metal commodity recycled by major scrap categories. In addition, energy requirements were estimated for separating municipal solid wastes into four major categories: Refuse-derived fuel, and magnetic, aluminum, and glass cullet fractions. Finally, areas of research were identified to enhance recycling and/or increase the efficiency of energy use.

Jan 1, 1978

By F. Albayrak

This report is a study of the impact of Federal laws and regulations on the domestic supply of metallic and nonmetallic minerals. The study was confined to pertinent environmental legislation and the recently enacted Federal Mine Safety and Health Act of 1977. Emphasized were the legal requirements placed on individual selected mineral industries, and the economic impact of these requirements. A certain amount of attention was also directed to the particular environmental and health and safety problems generated by selected mineral industries. The study also pinpointed a list of major problem areas having significant impact on the domestic mineral supply.

Jan 1, 1978

By Phillip M. Busch

VANADIUM was discovered in 1801 by Andres Manuel del Rio, a professor of mineralogy at the School of Mines in Mexico City. Del Rio called the new element erythronium. Later, he decided that this was not a new element but a form of chromium. Not until 1831 did Nils G. Sefström, a Swedish chemist, positively determine that the metal was a new element which he named vanadium, after Vanadis, the Scandanavian goddess of beauty. From 1831 to the 1860's and 1870's, the comparative scarcity and high cost of vanadium restricted its commercial use. Shortly after 1870, more information was obtained on the physical and chemical properties of the element. Thereafter, research on vanadium has dealt largely with its use as an alloying element in steel and nonferrous metals. Vanadium is a widely distributed element in the earth's crust. It is more abundant than many metals but is disseminated in small quantities throughout a great variety of rocks. Relatively few deposits have contained ore of a grade suitable to warrant development for vanadium alone. It is produced in conjunction with uranium, iron, titanium, aluminum, and lead-zinc ores.

Jan 1, 1961

By N. N. Malila, N. R. Shoko

The ever-increasing pressure on the profit margins of ferro-chrome producers and the gradual depletion of deposits of rich hard lumpy chrome ores calls for the ferrochrome industry to maximise the use of fine fractions of concentrates and friable chromite ores. Zimbabwe is endowed with huge deposits of refractory and friable ores that occur on and off the Great Dyke complex. The conventional metallurgical process of smelting of chromite ores in submerged arc furnaces is favoured by the use of refractory hard lumpy ores. The requirement to use all lumpy ore has been circumvented to a large extent at Zimbabwe Alloys. The use of briquetted chrome ore fines in the production of Ferrosilicon Chrome and High Carbon Ferrochrome has yielded positive results over a period in excess of twenty-five years. Of the three industrially used methods of agglomeration of chromite ores; sintering, pelletisation and briquetting, briquetting is preferred because the other two are associated with higher capital and operational cost. Zimbabwe Alloys has developed operational and technical expertise on the briquetting and utilisation of chromite ore fines and concentrates. Variations in the quality of available chromite ore fines imply that their amenability to briquetting is a dynamic problem. Appropriate briquetting parameters to guarantee quality briquettes are essential to the successful use of briquetted chromite ore fines. In developing a technology for briquetting of chromite ores, it is important not only to study the mineralogical and grain-size characteristics of the chromite ore fines but also to make an informed choice of the type and quantity of the binder and the conditions for producing a physically and chemically competent green and cured briquette. This paper discusses Zimbabwe Alloys' experience on the briquetting process and the advantages derived in the smelting of the briquetted chromite ore fines in comparison to the use of conventional lumpy chromite ore with respect to improvements in chromium recovery and as a consequence related efficiencies and unit cost of production.

Jan 1, 2004

By Wallace W. Key

Mineral raw materials produced in California, other States, and foreign countries were purchased for consumption in quantities valued at over $60 million at 800 of the 1,200 chemical plants operating in California in 1960, according to questionnaires completed by company officials. These and other data received from mineral consumers, producers, dealers, and Government agencies formed the basis for this the first of a series of reports designed to present the intricate features and relationships controlling mineral raw material supply and demand in California industries. The results of this study indicated certain changes in use patterns of minerals in chemica 1 manufacturing; a shift in requirements from metals to nonmeta ls, from inorganics to organics, from natura 1 to synthet ic materia ls , and from distant to local sources of supply.

Jan 1, 1965

By Charles W. Merrill

AN ADEQUATE, dependable, and continuing supply of raw materials is indispensable to tile the United States and its industries in meeting the needs of an expanding Population, a rising standard of living, and the national security. The primary responsibility for appraising the status of the country's mineral supply and for making appropriate recommendations within the executive branch and to the Congress has been pinned in the U.S. Department of the Interior. In fulfilling its role of governmental responsibility for raw-material supplies and their efficient utilization, the Bureau of Mines has analyzed the factors in current and future mineral supplies and demands and has developed 87 statements for specific commodities that assess the national position and problems for these metals, minerals, and mineral fuels. These statements, which constitute the chapters of this volume, are based on lire assumption that nearly till production and consumption of materials in the United States are to be by private individuals and organizations, in accordance with the Nation's devotion to a private-enterprise economy.

Jan 1, 1960

By Hazel J. Stratton

IN THE HALF-CENTURY that has passed since the Bureau of Mines was established in July 1910, the research and technologic investigations conducted by the Bureau's scientists, engineers, and other personnel have helped significantly in improving health and safety in the mineral industries and have contributed substantially in conserving the Nation's mineral resources through improved techniques in the mining, treatment, and use of mineral commodities. From Bureau laboratories have come new materials for industry and better methods of extracting and processing minerals and mineral fuels. Bureau safety investigations-complemented by equipment testing and by programs of mine inspection and education-have brought about safer and more healthful working conditions.

Jan 1, 1960

By B. Andresen, S. T. Johansen, H. Tveit, S. Grådahl, B. Ravary

The Norwegian ferroalloy industry has high ambitions regarding environmental standards. Basic research work has been performed to improve the fundamental understanding of ferroalloy processes and the environ-mental aspects. This paper will present work dealing with the understanding of formation and control of NOx, PAH and dioxins. During this work various techniques and methods have been applied, such as comprehensive industrial measurements, laboratory experiments, model development and application of Computational Fluid Dynamics (CFD). The main goal has been to reduce the environmental impact of ferroalloy plants, by means of improving the combustion processes done by introducing new charging routines and optimized furnace operations, instead of installing expensive gas treatment systems. The Norwegian obligations in accordance with the Gothenburg protocol are to reduce the NOx emissions by 30%, compared with the 1990 level within 2010. Measures developed in this work have resulted in 40-60%reduction in NOx emission, and major reductions in PAH and dioxins for ferrosilicon and silicon metal plants. This has been achieved by introducing semi continuous charging and improved furnace operations. Semi continuous charging and optimized furnace operations are shown to reduce the blowing activity (i.e. emission of large quantity of SiO over the charge by direct channelling from the crater zone). It also reduces variation in off-gas temperature and dust production. To understand the processes and to achieve our results we have used online equipment, with fast sample rates and response times, to measure the off-gas compositions and temperatures. Most of the measuring techniques used are based upon optical principles making use of the absorption- and emission spectrum of the gases. In addition a new prototype instrument is developed for continuous measurement of off-gas characteristics, total dust amount and off-gas temperature. The presented work is a result of a long term co-operation research and development teamwork, between the industry and the research community, and has improved both the process and reduced the emissions. The work has introduced new process design and operation standards, and has resulted in ferroalloy production with better environmental standards.

Jan 1, 2007