Search Documents

By Kirsi M. Riihilahti

The oxidation characteristics of solid copper matte particles under simulated Kennecott-Outokumpu Flash Converting conditions are presented. The effects of feed matte grade, matte particle size, oxygen-to-matte mass ratio, oxygen content of the process gas and temperature on the particle oxidation rate, quality of conversion, particle size change and particle morphology were determined. The converting quality was highest (~68) with the 58% copper matte at 1100°C. At similar conditions, the 72% copper matte was more likely to produce copper oxides and leave unoxidized particles rather than directly produce sulfur dioxide at 1100°C, resulting in an average converting quality of 55. The quality of conversion was poorest for the 72% matte at 920°C (~45); the sulfur removal was extremely low even with a relatively high degree of oxidation. Fragmentation of the particles was significant in all cases with the 72% matte. A higher O2/matte .ratio and higher temperature, in general, resulted in increased fragmentation while oxygen enrichment had no significant effect. With the 58% matte, particle size was found to increase for the finest fractions rather than to decrease due to particle expansion.

Jan 1, 1998

By Osamu Takai, Yoshiki Sato, Nobuhiro Tajima, Hiroyuki Sugimura

"Amorphous carbon thin films doped with nitrogen ( a-C:N) have been synthesized by means of shielded arc ion plating (SAIP). Their electron field emission properties, that is, threshold field strengths for electron emission and maximum emission current densities, were evaluated and compared with those of pure amorphous carbon (a-C) films prepared by the same SAIP apparatus. Among all of the fabricated a-C:N films, the a-C:N films with a N concentration of 23 %, which prepared using Nz arc plasm at a pressure of 1 Pa with applying a sample bias voltage of -100 V, showed the lowest threshold filed of 13.4 V/µm and the highest emission current density of 1.87 µAfcm2 at a field of20 V/µm. These field emission properties of the a-C:N film were much better than those of the a-C films. The best results obtained on the a-C film in this study were the lowest threshold filed of 15.5 V/µm and the highest emission current density of 0.052 µA/cm2 at a field of 20 V /µm. Nitrogen doping to aC was found to be effective for lowering threshold voltage for field emission and for increasing emission current density. The electron field emission characteristics of the a-C:N films depended not only on N concentration but also on chemical bonding state of nitrogen in the a-C:N films. The presence of the ~-C3N4-like phase, which contributes to improve wear resistance of a-C:N as well, distinguished by the NlsXPS peak at 400.5 eV is proved to be crucial in order to enhance field emission properties of a-C:N.IntroductionThere has been much interest in electron field emission from a cold cathode due to its potential applications in vacuum microelectronic devices including field emission displays which are expected as flat panel displays in next generation [l]. It is well known that efficient emission can be rather readily realized using tip-like shape cathodes, e.g., microfabricated three-dimensional electrodes [2], carbon nanotubes [3-5], etc. However, electron emission from planar surfaces is of particular importance since such a type of cathode is· simply fabricated and assembled into microelectronic circuits. Currently, amorphous carbon thin films doped with nitrogen (a-C:N) prepared by plasma processes have attracted attention because their threshold voltages of field emission are relatively low [6]. Among various methods for preparing a-C:N films, the process using arc plasma is of special interest since, in arc plasma, nitrogen is highly activated and new types of carbon nitride phase are expected to be synthesized. However, field emission properties of a-C:N prepared by arc plasma have been studied in less detail compared with that prepared by the other methods such as sputtering."

Jan 1, 2000

By Edgar E. Vidal

The deposition of ceramic materials onto substrates is of special interest in the development of surface related technologies. Research interest has been placed on using thermal plasma as the deposition method, specifically inductively coupled plasmas. Many different modifications to the same basic principle of deposition have been performed through out the materials research community. Such a technique may have many advantages over more conventional techniques, such as high deposition rates, high surface area coverage, clean energy source, no contamination from electrodes and operation near atmospheric pressures. Materials deposited vary from simple oxide systems like TiO2 to more complex structures like ternary oxides and nitrides. This paper reviews recent developments relative to the inductively coupled plasma deposition of thin films.

Jan 1, 2003

By Paul C. Turner

In 1998, approximately 57,000 tons of titanium metal was consumed in the form of mill products (1). Only about 5% of the 4 million tons of titanium minerals consumed each year is used to produce titanium metal, with the remainder primarily used to produce titanium dioxide pigment. Titanium metal production is primarily based on the direct chlorination of rutile to produce titanium tetrachloride, which is then reduced to metal using the Kroll magnesium reduction process. The use of titanium is tied to its high strength-to-weight ratio and corrosion resistance. Aerospace is the largest application for titanium, and titanium cost has prevented its use in non-aerospace applications including the automotive and heavy vehicle industries.

Jan 1, 2001

By Mansoor Barati, Shaghayegh Esfahani

"The slag from extraction of ferrous and non-ferrous metals is a potential heat source which if treated properly can contribute to recovery of a significant amount of energy. The waste heat of slag may be used to generate steam, synthetic fuel gas, or electricity. Although several technologies have been investigated for this purpose, very little has been achieved in terms implementing the technology in industry. In this article, the development and application of various granulation techniques are reviewed and the methods to recover energy from granulated slag are discussed.IntroductionEvery year, more than 422 million tons of slag is being produced around the world as a by-product of the metal manufacturing at temperatures of up to 1300-1600°C [1, 2]. Currently slags are either disposed of or treated by processes such as granulation. Through the granulation process, most slags can be converted into a material which may be fully used as a cement feedstock. Conventional cement production is an energy intensive process with large emissions of CO2; therefore, the replacement can both be energy saving and environmentally friendly. However, for this purpose, the slag should have what is known as a “glassy” content (i.e. it should be amorphous) which requires rapid cooling rates that are not easily achieved due to the very low thermal conductivity. The main challenge in all these processes is to granulate the slag at a high cooling rate while the heat is also being recovered."

Jan 1, 2012

By Xu-ling Chen, Qian Li, Yong-bin Yang, Zhao Jing, Tao Jiang, Guang-hui Li

"It is generally known that alkali metals are harmful to blast furnace production resulting in aggravating RDI of sinters, abnormal expansion of pellets, deteriorating blast furnace lining, etc. Sinters regarded as dominating burden of blast furnace are determined as the main source of alkali metals. In this study, the removal behavior of potassium and sodium oxides by pre-reduction sintering during the sintering process was studied. The removal ratio ofK20 and Na20 was greatly influenced by coke powder content, carbon species, coke powder adding ways, additive and so on. Under the conditions of carbon rate 12% and 5% dosage of CO supplied in the sintering process, the corresponding removal ratio ofK20, Na20 was 69.00% and 32.79%, and metallization ratio could reach 4.65%. This technology provided a novel process for reducing the content of alkali metals in sinters and dramatically improving the quality of blast furnace burden.IntroductionSinter is the main iron-bearing charge of blast furnace for iron-making in China, making up about 80% of the total burden; therefore, its quality has a significant influence on the quality of pig iron and blast furnace operation. Research and practice of numerous years prove that potassium and sodium coming from ores are brought into blast furnace and upgraded, which is one of the essential reasons that lead to blast furnace nodulation and influences its strength. Currently, effective flow sheet to remove potassium and sodium is weak magnetic separation-intensive magnetic separation-flotation [l], while iron ore concentrate is still ofhigh levels of potassium and sodium. As sintering process is also not effective to remove potassium and sodium, blast furnace in China is of high alkali burden, e.g. it reaches 5.6-6.2kg/tFe in Baotou iron making plant, which is greater than international tolerated level of2.55kgltFe [l]."

Jan 1, 2013

By Mikko Loponen

Outotec has developed an operator training simulator (OTS) platformsuitable for various hydrometallurgical processes. The complete solution is run in the cloud, where virtual client instances can be managed on-demand. The aim is to build a generalizable model that produces coherent results even when operating outside of ideal parameters, allowing the operator to train in unsteady state conditions such as start-up and shutdown. Complex software products are commonly associated with significant development time and cost. Utilizing modular software architecture, only the control system and processmodel are tailored for theOTS,whereas modules such as user administration and cloud-based client machine spawning can be imported, shortening development time. A generic acidic pressure oxidation process (POX) operator training simulation consisting of feed preparation, autoclave, dual-stage flash evaporation and off-gas scrubbing is described. Process is simulated using Outotec HSC Sim 9 process simulator and controlled by Siemens Simatic PCS7 control system.

By J. B. W. Bailey

The Noranda Horne smelter in Quebec, Canada has change considerably during the last two decades to accommodate varying custom concentrate receipts, closure of the Horne mine, better working conditions, environmental programmes, new technology and increased energy and labour costs. This paper highlights the reasons for changing the smelter from two calcine charged and one wet charge reverberatory furnaces fired by coal to a smelter using. tonnage oxygen oil, natural gas and coal in a single wet charged reverberatory furnace and a Noranda Process continuous Reactor. The current operation 1 described, including three major topics; the use of oxygen/fuel burners on the charge banks of the reverberatory furnace which has increase the smelting rate from 680 to 1100 tonnes of concentrate per day; the oxygen enrichment of the Noranda Process converting air to achieve smelting rates of over 1800 tonnes of concentrate per day; the converting of the mixture of 73 percent copper matte produced from the Noranda Process and the 33 percent copper matte produced from the reverberatory furnace.

Jan 1, 1983

By D. J. Droppert

This paper describes the precipitation-production of crystalline scorodite (FeAs04.2H20) from arsenic-rich sulphate-based metallurgical solutions at ambient pressure (95°C). Arsenic is precipitated by means of a controlled precipitation technique in which the supersaturation of the solution is carefully controlled. By controlling the supersaturation in the presence of seed material. the formation of amorphous ferric arsenate is prevented. Scorodite is known to be the most stable As(V) compound and is therefore preferred as host mineral for arsenic immobilization. The effect of the following parameters on the preCipitation behaviour and kinetics of scorodite are discussed: Type of base seed concentration initial [As]. sulphate concentration. neutralization rate. seed recycling and method of Fe(ll!) addition to Fe-deficient arsenic solutions.

Jan 1, 1996

By Xuewei Lv, Yuelin Qin, Guibao Qiu, Chenguang Bai

"Blast furnace slag (BF slag), is the main by-product in the ironmaking process, which contains large amounts of sensible heat. To recover the sensible heat, this paper described the hot experiments which were carried out in a rotary multi-nozzles cup atomizer, where the molten BFS was transformed into granules without water impingement; subsequently, a new method-pyrolysis the printed circuited board (PCB) with the hot BFS particle, was proposed for recovering the sensible heat in this study. The gaseous products were analyzed by gas analyzer. The residual of the PCB was analyzed by FT-IR and XRD respectively, and the obtained slag particles were analyzed by XRD.The results showed that it is a feasible process of pyrolyzing PCB powder with the hot BFS particle. The sensible heat of hot BF slag could be converted to chemical heat and a large amount of combustible gas could also be generated during the process.IntroductionDue to the rising of the product cost of blast furnace iron (BFI) and the increasing public awareness of environmental problems, the steel industries have to focus on the energy saving and emission reduction. Blast furnace slag (BF slag) is a byproduct from blast furnace exhaust temperature of 1450°C or so, is a high-quality waste heat resources. In China, the steel industry produces approximately 220Mt ofBFS per year, and the enthalpy of those slags is approximately equivalent to 13.3% of the whole energy consumption in the ironmaking process[!]. It can be seen, recycling waste heat is an important way of energy saving for iron and steel enterprises. The molten slag was treated by conventional water quenching method without any recovery of heat in spite of its huge potential. Also, the water quenching process consumes a plenty of water, pollutes the air and water[2]. Additionally, the extra energy is necessary for the drying process of slag to produce cement. As a kind of secondhand resource which can be reused, the BF slag contains a large amount of sensible heat. To recover the sensible heat of BF slag, three key problems should be considered, which refer to ( 1) the dry granulation of BFS without consuming water, (2) how to recover the heat of slag particles efficiently, (3) how to use the slag particles after heat recovery."

Jan 1, 2012

By W. G. Davenport

Chapters 7,8and 9 calculated three combinations of: blast composition (mass% O2, mass% N2) oil quantity per tonne of concentrate blast temperature that will steadily produce molten 65% Cu matte from pure chalcopyrite-concentrate. The combinations are:

Jan 1, 2001

By T. T. Chen

A mineralogical study of copper anodes and copper anode slimes was carried out to elucidate the silver phases present and the behaviour of silver during copper electrorefining. Most of the silver in the anodes is in metastable solid solution in the copper metal. As the copper dissolves, silver also dissolves, but is rapidly removed from solution by a variety of reactions. Some of the silver is precipitated as Ag by cuprous ions and some is precipitated as a complex CU-Ag-Pb-As-Se oxidate phase. Much of the silver, however, reacts with copper selenides to form, progressively, (CU,Ag) 2se, AgCuSe and Ag2se. The reaction commences at the periphery of the selenide grains and progresses inward; the result is commonly a silver-rich species on the outside of a silver-deficient core. Slimes collected periodically throughout the electrorefining cycle show a progressive silver enrichment of the selenides. Traces of Ag2Te also may be present, but the telluride seems to J:ie a rare constituent of most raw anode slimes.

Jan 1, 1989

By Andreas Siegmund

During the decade of the nineties the conventional method of primary lead smelting (sinter machine/blast furnace) was successfully challenged by the introduction of novel direct and continuous smelting processes. In combination with a significant shift in market structure, as well as more stringent government regulations these modem technological innovations like the QSL, Kivcet, and Isa/Ausmelt processes became more than major competitors. They have proven to be economically and environmentally viable. The intensification of the metallurgical reaction by applying oxygen enriched or pure oxygen bath or flash smelting principles resulted in cost savings and a higher flexibility with respect to raw materials and additives usage. By synchronizing individual auxiliary plant sections with the smelting process a virtually waste-free production and low-emission mode of operation with nearly optimum energy exploitation is achieved. The primary lead industry will gradually substitute the sinter -blast furnace operation with novel high-energy efficient technologies in the new millennium.

Jan 1, 2003

By F. Elgersma

Hydrometallurgical zinc winning processes ?are frequently based on iron containing concentrates which yield a goethite, jarosite or hematite residue. Jarosite or goethite are mostly stored in waste ponds which ,are lined with foil. Water percolating through the pond is withdrawn from the deposit ,and decontaminated before discharge. Despite these measures, more and more pressure is put upon zinc companies to treat their (historical) residues and to produce environmentally acceptable residues. The criterion which determines this acceptability is the potentiality of leaching out hazardous elements by natural processes. This paper provides the comparison of five different process designs for integrated jarosite treatment in a hydrometallurgical zinc winning plant leading to environmentally acceptable residues. The processes are esigned for producing 200 ktons/yr zinc and for treating 80 ktonslyr historical jarosite. Mass and energy balances are used to determme parameters such as: the energy use per ton waste treated and the amount and composition of final residues. The conclusion of the work is that. pyrometallurgical jarosite treatment integrated in hydrometallurgical zinc winning is preferable to hydrometallurgical jarosite treatment. Integrated pyrometallurgical processes lead to a ?smaller quantity of remaining hazardous residues and require less energy.

Jan 1, 1992

By S Ivanaj

Oxidation of chalcopyrite from a copper concentrate in an electrochemical cell having separate-anodic and cathodic compartments was studied by potentiodynamic, potentiostatic and galvanostatic experiments. Oxidation of chalcopyrite particles was mainly realized by in-situ electrogenerated FeIII and Cull ions. The use of an ion exchange membrane, in this experimental set, avoids the reduction of the ferric and cupric ions. The effects of particle size, current feeder potential, current intensity and pulp density were studied to optimize the oxidation parameters. Selective complete oxidation of chalcopyrite was achieved. Oxidation of pyrite was negligible. Mom than 85 % of sulfur was obtained in its elemental form. This may allow selective extraction- of copper from the chalcopyrite concentrate without sulfur dioxide emissions.

Jan 1, 1995

By J. J. Talja

An investigation of oxidation of various nickel concentrates was carried out using differential scanning calorimetry (DSC). The aim of this study was to determine the ignition temperature and investigate other oxidation behavior of various sulfide-based nickel concentrates. Variables in the experiments were mineralogy, particle size and partial pressure of oxygen with temperature increasing linearly at 25 K/min from 323 to 1023 K (50-750 °C). The igni¬tion temperature was determined to represent the starting point of rapid oxidation. The reac¬tion enthalpies of the concentrates were determined and the amount of heat generated up to various time were used to calculate the extent of reaction. Mineralogical changes at various stages of oxidation were also investigated. For this purpose a second set of DSC-experiments were carried out in which each experiment was interrupted at a desired temperature between 673-873 K. From these tests the weight loss of samples were determined and changes in the individual constituent of sulfide minerals were analyzed. For pentlandite-based Ni-concentrates the ignition temperature was 705-710 K (approximately 435 °C). Pyrite was the first sulfide to oxidize. Reactivity of the violarite-based concentrate was greater than those of the pentlandite-based concentrates. The stoi-chiometry of pentlandite changed before ignition because of preferential oxidation of iron. Rapid oxidation of the pentlandite mineral occurred at about 823 K (550 °C). By 900 K about 90 % of the iron in pentlandite was converted to hematite, and NiS containing some iron was formed.

Jan 1, 1994

By Dimitrios Fillippou

Magnesium hydroxide is used in a number of industrial applications, from the neutralisation of acid effluents to the production of pharmaceuticals. High-quality magnesium hydroxide powders can be produced by hydrating slow-reacting magnesia in dilute magnesium acetate solutions. The process of magnesia hydration shows many similarities with a typical hydrometallurgical leaching operation; however, its kinetics are crucial not only for process design and control, but also for the production of powders with a desirable particle morphology. This article shows the results of an experimental work whereby industrial heavily-burned magnesia powders were hydrated in 0.01 to 0.1 mol/L magnesium acetate solutions at temperatures ranging between 333 and 363 K. Examination of the magnesium hydroxide produced and the analysis of the kinetic data suggest that the hydration of heavily-burned magnesia in magnesium acetate solutions is a dissolution-precipitation process controlled by the dissolution of magnesia particles. The activation energy was estimated to be 60 kJ/mol, while the reaction order with respect to magnesium acetate concentration was found to be about one.

Jan 1, 1999

By B. C. Jena

Activities of carbon, cobalt and nickel were evaluated in the ternary systems iron-carbon-cobalt and iron-carbon-nickel for the temperature range 1300-1600°C for cobalt and 1300-1700°C for nickel. The carbon activities were determined from the knowledge of activities (1) in the binary system iron-carbon, (2) in the dilute ternary systems and (3) from the knowledge of carbon saturation data. The activities were mathematically expressed with the Taylor series expansion of Wagner's interaction parameter formalism modified to suit concentrated solutions. The cobalt and nickel activities were determined from the knowledge of carbon activities by applying the Gibbs-Schuhmann integration and from cobalt and nickel activities in the binary systems iron-cobalt and iron-nickel. Partial molar enthalpies of mixing were determined based on the temperature behaviour of the activity coefficients.

Jan 1, 1992

By Michael J. Nicol

Growing environmental and occupational safety concerns about the use of cyanide in gold processing has increased the interest in more acceptable alternatives. The most likely of these is thiosulfate. However, the thiosulfate process lacks a proven in-pulp method of recovering the dissolved gold, because activated carbon is not effective for the absorption of the gold thiosulfate complex .. Anion exchange resins do offer a possible route for in-pulp recovery. This paper describes work aimed at the evaluation of the effectiveness of commercially available anion exchange resins for the recovery of gold from thiosulfate leach liquors? and pulps. It has been found that strong-base resins are superior to weak-base resins in that they have a larger capacity, which assists in reducing the competition from other anions within a leach solution. Further studies with a selected commercial strong-base resin have shown that competing polythionateanions (particularly tri-and tetrathionate). Lower the maximum possible gold loading but that gold is selectively recovered over other base metal anions in solution. Kinetic experiments found that while? competilig anibns did not affect the initial rate? of gold loading it was important to minimise the contact time of the resin in solution so to prevent displacement of loaded gold by competing anions over longer times. A small-scale resin-in-pulp plant investigation showed gold can be recovered from a leach pulp by a strong-base resin to yield gold loadings of 3000 mg/L, barren pulp containing less than 0.05 mg/L of dissolved gold and. copper loadings of 500 mg/L. Loaded copper was displaced gold and at a loading of 2000 mg/L gold the copper loading was minimal «500 mg/L). The resin was found to recover gold adsorbed on the solids that would, otherwise have. reported to tails if a solid/liquid separation method were used. A patented two-step elution process in which copper and then gold are separately eluted from the resin is also discussed.

Jan 1, 1998

By Ernie M. Crist, Laurentiu Nastac, Frank Spadafora

"This paper describes the modeling techniques and the experimental and computer results for two casting processes that are under development and optimization. These processes are described as follows:1) Electromagnetic stirring (EMS) during casting of Ti-6Al-4V round ingots using the plasma arc cold hearth melting (PAM) process: The purpose of EMS is to establish a singlemelt PAM process capable of consistently producing as-cast ingots without helium porosity and also having no need for surface conditioning prior to secondary processing.. The modeling approach is based on the numerical solution of Maxwell's equations, fluid flow, and heat transfer equations, and mesoscopic modeling of the grain structure.2) Casting of Ti-6Al-4V slabs using the single-melt PAM process: The purpose of slab casting is to improve yield by eliminating an intermediate blooming step for converting round ingots to slabs. The modeling approach is based on the numerical solution of fluid flow and heat transfer equations. The effects of pouring and mold temperatures on the pool and temperature profiles were studied. Also, the torch effects (such as the torch standoff and its traversing path) on the pool and temperature profiles were investigated and the best-case scenario was used in the experiments. Evaluation results at RMI Titanium Company showed that the plates made from the slabs met the mechanical properties and microstructure requirements.Acknowledgment. This work was conducted by the National Center for Excellence in Metalworking Technology (NCEMT) operated by Concurrent Technologies Corporation (CTC) under contract No. N00014-00-C-0544 to the US. Navy as part of the US. Navy Manufacturing Technology Program. Dr. K. b. Yu from RMI and my colleagues from CTC are acknowledged for their comments on this work."

Jan 1, 2004