Search Documents

By S. Motoiu

Data acquisition is widely used for controlling flash smelting furnaces. A Romanian smelter from which a large amount of data can be collected uses such a technique. A computer program was developed for interpretation of the data. Inputs to the program are the process data files. Abnormal data are identified using standard statistical techniques; they can be edited if necessary. The following methods can be used for the analysis: linear correlation (single or multiple), polynomial correlation or comparison of two average values. Time variation graphs and histograms can be displayed. The random balance method was used for determination of significant parameters influencing the process performance. Not all process parameters are recorded, and some of them are not even measured. The software can compute some of these parameters such as: air flow rate required and the oxygen content of the gas: exiting the reaction tower. The software was used for the interpretation of a large amount of process data. The analysis showed that the process did not operate properly at some times.

Jan 1, 1999

By Markus A. Reuter, Antoinette van Schaik

"Product design engineers select from a wide range of materials and combine them into multimaterial product designs. These include various materials (metals and non-metals) which are complexly integrated (e.g. welded, glued, alloyed, layered). The recycling/recovery rate of consumer products are determined by the different materials and alloys used, but also by the particle size and multi-material particle composition after shredding (combination of materials due to design). Eco-design (for recycling) and Design for Recycling (DfR) can only be conducted if the interconnectivity of material/metal in various unliberated materials is accounted for and its effect on material and energy recovery can be linked back to design. This paper will discuss the basic principles of these DfR models and it is shown how these tools (i) are linked Computer Aided Design (CAD) and Life Cycle Assessment (LCA) software, (ii) affect conceptual design specifications of products, (iii) integrate the complex detail of the recycling system and recyclate quality and hence (iv) make recycling an integrated part of the product system. Furthermore, it is shown how these assessment tools and models can be applied for benchmarking of the recyclability and environmental damage created by the recycling of end-oflife consumer goods in order to e.g. (i) provide the (original) equipment manufacturer with knowledge and solutions to support product stewardship and Extended Producer Responsibility; (ii) create awareness of the consequences/benefits of design, products and recycling systems to manufacturer, designer, legislator, recycler etc.; and (iii) assist the consumer in their choice of consumer goods from an end-of-life point of view.IntroductionA first-principles basis is required in order to be able to simulate and predict the recycling/recovery behaviour of products facilitating Design for Recycling (DfR) and Eco- Design. This links recycling technology and the environmental consequences of recycling directly to product design."

Jan 1, 2008

By Anthony C. Mulligan

Metals have historically been used in mining since they offer an excellent combination of hardness, toughness and cost and can be fabricated to form a variety of shapes. However, for many applications the metals used today have limited performance in the environments in which they are needed. This is particularly true for geothermal environments where the brines are highly siliceous causing corrosion and accelerated wear of many components. Geothermal sources are increasingly being explored for their high thermal value as well as possible sources for future minerals. While advanced ceramics have historically been expensive to produce in comparison with metals, they offer significantly greater corrosion resistance and hardness and can improve the overall performance when used in selected ?problem? areas. One of the major drawbacks in the use of ceramics in high impact areas has been their brittle nature and propensity to fracture and spall (fail) when loaded. Recent advances in the fabrication of ceramics have combined hard (strong) ceramics with more ductile ceramics in a architecturally designed microstructure, thus allowing ceramics to perform well in these high impact regions. Additionally, ceramics are significantly more inert to corrosion from either alkaline or acidic environments and can typically be used for significantly longer periods in these environments than their metallic counterparts.

Jan 1, 2006

By Pradip

The selective adsorption of chemisorbing fatty acids at high temperatures together with the addition of soda ash and lignin sulfonate as depressants is the key to the industrial processing of bastnaesite ores. This paper presents the results of a fundamental investigation that indicate that alkyl hydroxamates can be an alternative collector for the beneficiation of bastnaesite ores that contain barite and calcite as the principal gangue minerals. The primary mechanism for providing sites for the chemisorption of hydroxamate on bastnaesite appears to be through dissolution of cations, formation of the respective hydroxo complexes and readsorption at the interface.

Jan 1, 1989

By Ravinder N. Reddy

Electrochemical capacitors are charge storage devices. They bridge the gap between dielectric capacitors and batteries in terms of energy and power density. Electrochemical capacitors are classified into two types, electrochemical double layer capacitors (EDLCs) and capacitors based on pseudocapacitance. In EDLC, charge is stored at the interface between electrode and electrolyte. Carbon is considered to be prime electrode material for EDLCs due to its many favorable characteristics. In this study carbon materials are derived from thermal decomposition of catechol- formaldehyde polymers and are studied as electrode material for electrochemical double layer capacitors. Carbon electrode surface is characterized using NOVA 1200 gas sorption analyzer. It is also characterized using XRD and SEM. Carbon electrodewaselectrochemically characterized using cyclic voltammetry (CV). A highest capacitance of 110 F/g was observed in 30 wt% H2SO4.

Jan 1, 2006

By Robert D. Boiler, Bill Wilkie

"There is a wide choice of different types of woven filter media for hundreds of different filtration applications. Factors such as type of fiber, synthetic polymers used, weave style, fabric finishes and fabrication techniques all play an important part in selecting the best choice for a specific type of filter and process application. The purpose of this paper is to offer some basic knowledge of these factors and how they can impact the performance of a filter, the life of the media and the overall cost of operation through case studies of actual plant filtration applications.IntroductionThe use of woven filter cloth in liquid/solid separation applications is generally well known. Woven filter cloth, by the nature of the weaving process, offers unique consistency and repeatability when compared to some other filter media such as needled felts, papers, sintered structures and knitted cloth. This unique consistency and repeatability is particularly applicable to woven filter cloth produced using monofilament fibers. These fibers are consistent in shape and form the basis for a woven cloth with predictable pore size and throughput characteristics. Woven filter cloth can be used in most wet filtration applications. Typical examples are the separation of chemical and pharmaceutical solids from process liquors, waste stream solids capture, liquid foods clarification, mining separations, and polymer filtration.EnvironmentOne of the first considerations is the environmental demand of the given process. Though it is tempting to look immediately at the particles in a filtration process, it is often better to consider some of the more basic needs of the system. There are numerous materials available, both synthetic and wire cloth. Each has its own unique set of properties."

Jan 1, 2012

By F. E. Katrak

Rare earths markets by definition usually include not only the rare earth elements, but also yttrium. They can be subdivided into a very large light rare earth fraction (about 95 percent by weight of all rare earths consumed) consisting mainly of cerium and lanthanum and a smaller fraction (with much higher unit value) consisting of selected high-purity oxides or elements such as yttrium, europium, samarium, or neodymium. CRA estimates that the noncomnunist world market for all rare earths and yttrim was on the order of US$750 million in 1986. The main focus of this paper is on the principal uses for rare earths, some CRA-developed proprietary data on their consumption by region, and the selective nature of business opportunities in the rare earth markets. We also provide forecasts on the future trends in these markets.

Jan 1, 1989

By Chang Wei, Fan Zhang, Zhigan Deng, Minting Li, Cunxiong Li, Gang Fan, Xingbin Li

Marmatite is an important resource of zinc, which exist in forms of high iron and high indium. In order to recycle the valuable metal from these ores, the testwork of simultaneous leaching on neutral residue mixed with zinc concentrate of high iron and high indium has been conducted. The primary objectives are to leach the zinc and indium remaining in the neutral leach residue as ferrite using acid, and to reduce the ferric iron in solution to the ferrous by zinc concentrate, thereby extracting the zinc and indium in the zinc concentrate. The results indicated that in the following conditions, mass ratio of neutral residue to zinc concentrate of 1:0.25, particle size of 74-58 μm, initial sulfuric acid concentration of 150 g/L, liquid to solid ratio of 8 L/kg, temperature of 90°C, reaction time of 4h, the leaching efficiency of zinc and indium were over 95%, nearly 90% Fe was Ferrous in the leaching solution. This process effectively extracted zinc and indium and converted Fe3+ into Fe2+ in solution, and simplified the traditional process of reduction after leaching.

Jan 1, 2016

By Freddy Syvertsen, Ali Riza Tarakcilar, Engin Tan, Derya Dispinar

"It has been shown that the disturbance of the advancing liquid front in the mould cavity may lead to surface entrained defects known as bifilms. These defects can deteriorate the mechanical properties significantly. The developments in the simulation of castings aid many casters. It is quick and economical. Therefore in this work, the aim was targeted to optimise the mould filling of a tensile test pattern design that is used for aluminium alloys. Several different designs, gatings and runner systems were investigated with Vulcan Casting Simulation Software. In addition to the achievement of non-turbulent and quiescent mould filling; other parameters such as temperature profile, porosity and feeding were investigated to optimise the process.IntroductionConsiderable effort has gone into understanding and controlling defects that are formed in aluminium and its alloys during casting. The conventional approach was the elimination of porosity by eliminating hydrogen in the melt simply due to the following reaction:"

Jan 1, 2012

By Thomas A. Post

The methodology of determining the optimum SX pumper-mixer system based on bench top, pilot, or small-scale solvent extraction systems, is demonstrated. The design of small-scale SX-plants is different than a full-scale plant. The difference is explained here. The use of dimensionless parameters Nh, Nq, and Np that describe the head, flow and power of the pumper is shown and how to use them for the scale-up. Additional data is required to determine the optimum operating range. Applications of this methodology were used to design well known currently operating SX plants. The emphasis on the optimization of hydraulic efficiency will be shown on examples, including how the hydraulic efficiency is affected when the throughput of the system goes beyond the design. Designs of all sizes of equipment will be shown which optimize the hydraulic efficiency.

Jan 1, 2003

By J. P. Ibáñez

The uptake of copper from extremely dilute aqueous solutions by alginate in the form of protonated dry alginate beads was investigated. Barium was used to cross link the alginate forming the beads. The effect of various experimental parameters such as pH and metal ions concentration on the uptake of copper were studied. The uptake was strongly dependent on the Cu-bearing solution pH up to a value of 4.5. A removal of 100% o was achieved when the initial concentration of copper was as low as 8.0 mg/L. The maximum uptake, i, e., the loading capacity, was found to be 167 mg of copper per g of beads. The mechanism governing the removal of copper was found to be ion exchange between protons of the alginate beads and cupric ions of the solution. For this ion exchange process a molar ratio, d[H+]/d[Cu2+], of 2.0 was determined. EPMA-EDX analysis of the Cu-loaded beads showed a uniform distribution of the ions throughout the structure of the alginate, regardless the solution pH. This may suggest that this sorbent material is a porous ion exchanger having high permeability and capacity. The uptake of copper and of the heavy metals cadmium and zinc by this sorbent is compared.

Jan 1, 1999

By Junji Shibata

Through-hole copper plating is performed to make a multi-layer printed circuit board. The through hole plating is first carried out by Pd catalyst treatment, followed by copper non-electric plating. The amount of Pd catalyst used in one plant is about 0.25-2 m3/month (8 g/dm3 PdCl2 base) depending on the plant scale, and the cost of the catalyst reaches 17,000¬I35,000 US$/month. In this study, the flow and material balance of a Pd in Pd catalyst treatment process was investigated. About 60% of Pd catalyst adheres on the through-hole and other part of setup, while 25% is released into the washing liquor. Pd in the washing liquor should be collected by a suitable method like a pressure filtration using diatomite. The material balance of Pd in Pd catalyst treatment process and the recovery method of Pd from waste solution containing Pd catalyst was investigated.

Jan 1, 2003

By Manuel Alvarado, David Nemir, Jan Beck

"Thermoelectric generation using special N-doped and P-doped semiconductors is well known as a means for direct heat energy to electrical energy conversion without the need for moving parts. The technology is used today in niche markets for low level electricity production and has been proposed as a scalable means for capturing large scale energy from waste heat streams. The choice of geometry of the thermoelements and conductors is critical to the successful implementation of a waste heat recovery system in order to manage losses due to Joule heating and diffusive heat flows. This paper describes a simulation study to define the performance impact of different aspect ratios for the active thermoelements and the electrical interconnect. The use of a finite element model that incorporates the intercoupled heat and electrical energy flows highlights some of the issues impacting scalability.IntroductionThermoelectric phenomena arise out of the intercoupled electrical and thermal currents in a material. A two-element thermoelectric generator is depicted in Figure 1. It is constructed by connecting an N-type thermoelement and a P-type thermoelement in electrical series, with both elements in thermal parallel between a heat source and a heat sink. The electrical series connection is made by attaching conductors as shown. Ideally, these series connection elements will be both good thermal conductors and good electrical conductors.The two element generator in Figure 1 is disposed between two thermal reservoirs: the heat source, which furnishes heat energy; and the heat sink, which absorbs heat energy. Heat energy flux Q, flows from the heat source to the heat sink, driven by the temperature difference between the source and the sink. As depicted in Figure 1, when a resistive load, R, is attached, electrical current, I, may be extracted from the thermoelectric generator and furnished to the load. The N-type and P-type thermoelements, are the active portions that do the actual conversion of heat energy to electrical energy. Although thermoelements may be built using conductors such as bismuth and antimony, higher efficiency thermoelectrics are built using heavily doped semiconductors. Thermoelectric devices are generally formed by connecting many pairs (couples) of N and P type thermoelements in electrical series and in thermal parallel. A commercially available module having 127 couples (254 elements) is shown in Figure 2."

Jan 1, 2011

By Dan Adams

A number of gas-liquid processes require high intensity agitation systems to provide uniform blending and dispersion of reactants in order to achieve desired end products. Processes such as hydrogenation, fermentation, and minerals processing have used conventional down pumping or radial agitation systems with some success. In 1996, LIGHTNIN introduced the concept of Up-Pumping to the industrial marketplace as an improved mixing technology for these applications. For processes requiring gas-liquid mass transfer, such as those listed above, conventional mixing technology requires the use of gas introduction devices (sparges) below impellers. These devices can be a maintenance concern due to plugging and erosion in the presence of solids. Up-Pumping impeller systems are able to draw in a significant amount of gas from the headspace, much more so than conventional vortexing impellers designed for headspace gas incorporation. This paper will demonstrate the effectiveness of Up-Pumping impeller systems that have the potential to eliminate need for sparge devices entirely. It demonstrates the ability of Up-Pumpers to re-entrain gas for higher utilization compared with conventional impeller technology. This is significant in applications using costly gases such as enriched oxygen or hydrogen, reducing overall operating costs of production.

Jan 1, 2003

By David Forrest

In 1981, K. E. Drexler proposed using massively parallel nanomechanical systems to manufacture large atomically exact structures. As in macroscopic mechanical systems, they would contain components that serve traditional functions such as trusses for support, gears to transmit power, bearings for low-friction support of rotating surfaces, motors to supply torque, pipes and conveyor belts for material transport, and channels for coolant. Many of these components would only contain a few thousand atoms. Specific designs for these devices became available in the early 1990s, and a few working devices appeared in laboratories by the early 2000s. As advances continue, a thorough understanding of the operative transport phenomena will guide the intelligent design and construction of nanomechanical structures, devices, and systems. The familiar equations of continuum mechanics are generally inadequate to describe the flow of heat and mass in the proposed nanosystems. Boundary conditions often need to be described in terms of potential surfaces. Surfaces are not geometrically smooth, but periodic according to the locations of atomic nuclei. Friction occurs not due to the plastic deformation of asperities on mating surfaces, but to phenomena such as thermoelastic damping and phonon viscosity when atoms slide past each other. Electrostatic forces dominate over gravitational forces by orders of magnitude; there is no role here for natural convection. Structural components, no matter how stiff and strong, are in constant motion due to the thermal noise in the system. The fluids are described in terms of individual molecules in constant motion.

Jan 1, 2006

By lndu S. Das

An analytical simulation of the material characteristics of Inconel 718 is developed and bounds for mechanical and microstructural stability are obtained for isothermal and temperature-dependent cases. Experimental flow stress data using hot compression tests are reported for a wide range of temperature and strain at various strain rates. A parametric study of strain rate sensitivity, dissipation and entropy are presented. A complete set of processing maps delineating the stable and unstable regions are developed to help define the most efficient means of manufacturing an Inconel product.

Jan 1, 1992

By B. Fresz

Before aluminum is utilized in automotive bodies, the longevity of the electrodes employed in the resistance spot welding of aluminum must increase. This paper explores the affects of electrode composition on electrode life. To compare these variables, electrode tests were completed on a Taylor Wield welding machine using, Cu-Cr, Cu- Zr, Cu-Cr-Zr, Cu-Be, and Glidcop electrodes tested to 12.5%, 25%, 50%, 100%, and 150% lifetimes. Electrode diameters were found via a magnification technique using a PULNIM video camera attached to a low magnification Wild Heerbrugg stereo-zoom microscope. From these measurements, graphs of electrode life verses face diameter and weld number verses face diameter were created. Analyses of these graphs suggest that a single failure mechanism is responsible for electrode failure, though the number of welds until failure (100% electrode life) varied with composition (700-2000 welds).

Jan 1, 1999

By Pragna Bhakta

The use of microbes for sulfide oxidation was investigated as a potential treatment option for low-grade refractory gold ores at Newmont Mining Corporation. The resulting patented technology for heap biooxidation maximizes oxidation rate by distributing the microbial population on the ore before placement on a heap. This paper presents data on global oxidation rates based on oxygen uptake in a 50-kg column for sulfidic refractory ores from the Gold Quarry mine. The oxygen uptake data was converted to a global oxidation rate. The calculated global oxidation rate was used to determine heap cycling times for Newmont?s commercial heap biooxidation facility.

Jan 1, 2003

By M. Barkhudarov

The results are presented of research aimed at validation and development of a general purpose CFD code FLOW-3D. FLOW-3D is a commercial code developed by FLOW SCIENCE, INC. A number of physical modeling experiments involving the filling of cavities of different geometries with coloured water have been performed in order to compare the measurements with the results of computer simulations. Other numerical calculations were also done to be compared with the known analytical solutions.

Jan 1, 1992

By Reinhold G. Schulze

Thiourea is being applied as an industrial leaching agent for gold and silver only in a few cases. A GIP technique was developed which eliminates most of the obstacles against its use. Omission of an acid treatment and mild conditions for precious metals stripping from the loaded carbon simplifies process conditions in comparison to cyanide CIP technique. Examples are given.

Jan 1, 1989