Search Documents

By Wenbing Xie

At Renlou Coal Mine, Huaibei Mine Area, the track entry deformed significantly after longwall mining in an overlying multiple seams. The supporting characteristics of primary roof bolts and shotcrete with wire mesh are closely related to the movement of the mine?s surrounding strata. A case study of a track entry deformation was monitored during the longwall mining of a selected overlying panel. The measured data showed the unique entry deformation pattern during the longwall mining in the overlying seam. Underground extensometer measurement showed that entry stability was mainly affected by the periodic roof weighting of longwall mining in the overlying seam. The displacement of the deeper strata occurred a head of the immediate vicinity of the entry. Thereafter, deformation of the roof and floor strata was in the form of shearing of the shallower strata. Due to the use of heavy-duty roof bolting with wire-mesh, the roof-tofloor and rib-to-rib convergences were small, but the floor heave was large, greater than 80% of the roof-to-floor convergence. The measured displacement from extensometers varied with the position of the monitored cross-sections and depth into the roof. There were several deformation patterns, such as shearing movement, compression, and expansion, and the variations between compression and expansion. Strata compression at the entry surface was always accompanied with shearing movement at the deeper strata. During the longwall mining, the whole surrounding strata of the entry moved toward the opening. Underground practical experience indicated that prior to mining, the entry was supported very well in excellent conditions. After mining, however, it deformed greatly. The current entry support technology was not effectively control the severe deformation incurred in entries driven in soft strata due to the following reasons: (1) little is known about the entry deformation behavior of the strata surrounding the opening and (2) the degree of interactions between entry deformation and roof bolting with wire mesh is not well understood. Consequently, effective supporting systems cannot be properly selected to control its deformation and maintain a stable supported surrounding structure.

Jan 1, 2012

By Thomas M. Barczak

The era of the shield-supported longwall face began in the United States a little over 25 years ago. The most fundamental development of the shield in the past 25 years has been an increase in size and capacity and a progression toward two-legged designs in favor over four-legged shields. Is the ?bigger-the-better? design philosophy justified? The advantage of the two-legged design is largely attributed to its active horizontal force caused by the forward orientation of the leg cylinders. How do we know this? You might be surprised to learn that shield loading data may suggest otherwise. In addition, what about setting pressures? Should they be set as high as possible? Some people have advocated that setting pressures should equal the yield pressure. Does this make any sense? Is yielding a good or bad thing? These are some questions still worthy of investigation that are addressed in this paper. The first major change in gateroad support was the use of cable bolts to replace conventional wood cribbing particularly in Western mines. Standing support changed very little until the mid-1990s, when Strata Products1 introduced the Hercules and Propsetter supports in Eastern mines and Burrell Mining Products introduced the Can support in Western mines. Since then, there has been a dramatic increase in new roof support technologies for longwall gateroad support. Historically, standing support, including shield supports, have been designed based on a simplistic model requiring the support to have sufficient capacity to support the gravity loading of a perceived detached rock mass. This approach ignores the stiffness of the support and the resulting ground deformation that is known to be critical to roof stability. Recently, a new approach based on the ground reaction concept has been promoted by the National Institute for Occupational Safety and Health (NIOSH) to account for the interaction of the support with the rock mass behavior in achieving ground stability. In addition to gateroad support design, this concept has ramifications for shield capacities, setting pressures, and recovery room support design that challenge current practices in these areas. Although longwall mining has matured into the safest and most productive underground mining method used today, traditional concepts of roof support design and practice should still be evaluated and challenged. Ultimately, advancements in the science of ground control are made by recognizing deficiencies in current theories and thinking outside the box.

Jan 1, 2006

By Christopher Mark

Severe dynamic multiple seam interactions can occur when active mine workings are subsided by underlying mining activity. The most dramatic events are usually caused by longwall mining or pillar recovery beneath open, overlying entries. But pillars in abandoned workings can also fail and cause subsidence and damage an overlying mine. This paper describes a case history in which an apparent ?pillar squeeze? in the abandoned workings of a lower seam was initiated during retreat mining in an upper seam. The event subsequently extended more than 1,500 ft and ultimately closed the upper seam mine. Analysis indicated that the pillars in the lower mine were adequately sized for the lower seam mining and were not affected by the initial development above them. When retreat mining in the upper seam had progressed several hundred feet, however, the pillars located directly beneath the pillar line were overloaded, and an extensive squeeze initiated in the underlying workings. The squeeze, in turn, subsided the overlying workings, causing widespread rib falls and roof instability. Previous examples of dynamic multiple seam interactions resulting from delayed subsidence of underlying workings have been reported in the literature. This is, apparently, the first recorded incident in which pillar recovery in an active mine triggered pillar failure in an underlying mine, which then triggered a dynamic interaction that impacted the active overlying seam.

Jan 1, 2012

By David Forrester

Subsidence beneath the land surface has traditionally been monitored using the most accurate surveying methods of the day. Over the several hundred years of subsidence investigation, these techniques have improved, and thus the accuracy of subsidence measurements has improved. In circumstances where the subsiding surface is masked by water or rock, novel methods must be developed. This method describes the recent successes of subsidence monitoring using advanced bathymeric techniques in the Sydney Coalfield. In order to obtain subsidence profiles above submarine coal extractions, seafloor bathymetry surveys, run before and after mining, have shown that subsidence profiles can be detected, despite the primitive nature of some of the trials. Very recently, there have been considerable advances in this field, associated with the availablity of high-powered personal computers to control data collection and analyse the results. The recent surveys described in this paper have demonstrated the considerable potential for such methods. This paper describes bathymetric subsidence monitoring developed in the Sydney Coalfield, illustrated with some typical results, and summarizes the findings of the research leading to the development of subsidence design criteria specific to the Sydney Coalfield.

Jan 1, 1996

By Andrzej Walentek

This paper presents the results of numerical modeling of the fractured zone around longwall gateroads. The numerical computations have been based on the results of underground measurements of the fractured zone around longwall gateroads, which were performed for various geological and mining conditions and measured with the use of the endoscopic method with a digital camera. Having results of the underground investigations, trials of duplicating them by the Finite Element Method using software PHASE and the Hoek-Brown failure criterion were performed. In order that the fractured zone predicted by the model-based computations closely simulate that measured underground, some selected parameters in the Hoek-Brown failure criterion were modified based on the earlier determined relations used for prediction of the roof-to-floor convergence in longwall gateroads. As a result, the model-based computations produce results very close to those obtained from the underground measurements. Determination of the fractured-rock zone around the mine roads is of great importance to mining practice, especially in planning and designing supports for longwall gateroads. The influence of the front abutment pressure causes the fractured rock zone around the roads to increase and results in an increase of support load. Moreover, proper determination of the fractured rock zone is one of basic elements in the process of planning roof bolting for mine workings.

Jan 1, 2009

By Jurgen te Kook

State-of-the-art for subsidence calculation are stochastical models. Although these models were successfully used all over the world they have their limitations due to the fact that they are not based on mechanical laws. For example the models did not take the rock mass structure and the rock mass characteristics into account. Therefore in a research program the skills of geomechanical numerical models for subsidence calculation were investigated. A case study shows that numerical models which are in principle based on the elastic theory are suitable for subsidence prediction. Due to the principles of these models the results are not sufficient in the case of multiple seam extraction. More extended geomechanical numerical models like FLAC and UDEC were investigated in further steps of the research work. Up to now large area geomechanical models require unrealistic long calculation times if the level of detail is similar to that of small scale calculations. Due to this it was necessary to implement a simplified description of the rock mass structure and characteristics. Different case studies show that this approach is successfull for subsidence calculation by numerical geomechanical models even for multiple seam extraction.

Jan 1, 2008

A model was developed to facilitate secondary tailgate support selection based on analysis of over 100 case studies, compiled from two different surveys of operating longwall coal mines in the United States. The ALPS (Analysis of Longwall Pillar Stability) program was used to determine adequacy of pillar design for the successful longwall case histories. A relationship was developed between the secondary support density necessary to maintain a stable tailgate entry during mining and the CMRR (Coal Mine Roof Rating). This relationship defines the lower bound of secondary support density currently used in longwall mines. The model used only successful tailgate case history data, with adequate ALPS SF according to the CMRR for each case. This model facilitates mine design by predicting secondary support density required for a tailgate entry depending on the ALPS SF and CMRR, which can result in significant economic benefits.

Jan 1, 1996

By Hamid Maleki

Having developed a methodology for estimating mining-induced seismicity resulting from slip along geological discontinuities in 2003, in this paper, the importance of measurements are high-lighted in the study of caving and seismic source mechanisms as applied to mine designs. Geotechnical data is analyzed from four case studies to address cave condition, load transfer, and potential effects on stability and resource recovery in four Utah mines using measurements and observations conducted over the last three decades. Cave conditions are evaluated on the basis of measurements in the gob of a western U.S. operation mining under the massive Castlegate Sandstone and indirectly using the results of measurements and boundary-element modeling at panel boundaries at a mine where strata behave elastically. Together with subsidence measurements and microseismic monitoring, regional caving and load transfer in multiple-panel extractions are addressed while the effectiveness of barrier pillars in reducing stress and seismic response where mining under massive stratigraphic units is analyzed using measurements and three-dimensional computer modeling.

Jan 1, 2006

By James J. Scott

Dynamic rock anchors are interior fixtures developed by the author which promise to be a revolutionary development in the field of ground control. The fixtures are designed to be placed in the ground with modern roof bolting equipment, such as the type used in the American coal mining industry. They are composed of a plastic form- able anchor tube which serves to fasten a buttress deformed rod which is thrust and turned into the plastic and in turn clamps the roof plate to the rock surface. Plastic tubes 10 to 16 inches in length provide sufficient anchorage to exceed the yield strength of steel rods 5/8, 3/4 or' 7/8 inches in diameter. This paper presents field testing and early work done on the device over the last seven years. Results of pull tests, creep tests, laboratory testing in concrete, and field testing under natural rock conditions demonstrate the uniqueness and effectiveness of this new support system. A second development which uses the dynamic rock anchor in conjunction with a resin cartridge to provide a stiffer anchorage system is also discussed. These products will be manufactured and marketed by Ingerso-11-Rand Co. under the trademark of DYNA-ROK and DYNA-ROK PLUS anchors.

Jan 1, 1989

By Jun Lu

There are many factors affecting the strength of pillar, including width-to-height (W/H) ratio, mechanical properties of coal and surrounding rocks, property of partings in the coal, and the interface property between coal seam and the roof/floor. In this paper, the effect of varying pillar?s width-to-height ratio (W/H=3, 5, 7, and 10) and coal/rock interface cohesion (Cj =50 psi, 150 psi, and 300 psi) on pillar strength has been studied. The confinement effect of W/H ratio and interface shear strength is investigated by studying their effects on the average minimum principal stress developed in the pillar. The deformation behavior of the coal pillar is investigated. It is found that the pillar?s transition from strain softening to strain hardening behavior depends on its W/H ratio and the interface shear strength.

Jan 1, 2008

By J. C. Johnson

High-grade ore found in a shaft pillar at the Homestake Mine prompted a request for a Bureau of Mines study to determine if selected areas of the shaft pillar could be mined without jeopardizing the shaft. The design approach was to perform a finite-element study of the shaft pillar. Plan view and vertical sections were developed using two-dimensional, elastic, plane strain assumptions. Input into the model consisted of in situ stress measurements geologic mapping rock mass properties, and previous mining history. Results from the study indicated that ore-beating sections of the shaft pillar could be removed within the displacement tolerances acceptable for the shaft. Homestake engineers, using the results of the finite-element study and considering other factors, have designed and are beginning to mine the shaft pillar.

Jan 1, 1989

By K. Unkug

It is commonly accepted that the tension of roof bolts can be used as a measure of the effectiveness of roof support performance in coal bearing strata. The conceptual base for the assumption originates from beam theory. Roof bolt tension acting across the bedding and other weakness planes increases friction, preventing potential separation and slippage within the roof strata and therefore, increases the stiffness of the roof beam between the open face and the rock-mass enclosed within the anchorage. Thus, it is important to monitor roof bolt tension, especially for research purposes, and consequently many measuring systems were developed based on numerous working principles. Research planned by the Department of Mining Engineering at the University of Kentucky required a large number of tension measuring devices of high precision. These were intended to operate reliably in corrosive mine environment over long periods of time. After evaluating the existing systems, it was decided to develop a new type of roof bolt dynamometer which would fulfill the above requirements at minimal Cost. Nearly one hundred such dynamometers were constructed, calibrated and installed in two underground mines. They remained in service for a period of one Year, producing a valuable database for the Project. In this paper the working principle of this new type of dynamometer will be described and technical considerations and samples of the collected data will be given.

Jan 1, 1986

By Peter Swanson

A seismic monitoring network has been installed in western Colorado (USA) in the vicinity of three underground coal mines to (i) distinguish and characterize seismic activity as either mining related or naturally occurring, (ii) implement a real-time event monitoring and notification tool, and (iii) collect data for use in research studies aimed at quantifying impacts from mining-related and natural seismicity. These potential impacts include dynamic rock mass failures such as coal bumps as well as strong shaking in the vicinity of critical structures such as impoundment dams, reservoirs, mine seals, mine openings, and steep slopes. Examples of two damaging seismic events are presented and the mining and geologic factors attending these dynamic failures are described.

Jan 1, 2008

By Takashi Sasaoka

The PT. Adaro Coal Mine targeted in this research is located in South Kalimantan, Indonesia. The coal production of this mine is increasing year, with about 35 M tons of coal produced in 2006. This mine faces many ground control problems, especially instability of the footwall. Large-scale landslides occur often in the footwall; this may be because of weak rock and the effect of footwall rock weathering. Hence, prompt measures must be developed and followed in order to preserve the stability of the footwall and make this mine safe. Additionally, the final pit design is now being reconsidered because of the increasing demand for and high price of coal. With these issues in mind, this paper describes a solution for improving the stability of the footwall and discusses the final pit design based on the results of an on-site investigation and numerical analysis.

Jan 1, 2008

By Arnold Hammons

Automated temporary roof support (ATRS) systems have been incorporated into roof bolters since the 1970?s. During roof bolting, many injuries have occurred from large pieces of draw rock falling inby the ATRS beam and tipping back into the operator?s area. Other injuries have occurred due to smaller, sharp rocks falling onto the operator?s hand and arm during initiation of roof bolt drilling. These injuries are attributed to weak immediate roof, sometimes called roof skin failure. Even though ATRS systems support the roof and provide a measure of protection against roof skin failure, additional hazards sometimes do exist immediately inby and outby the supported roof. Design innovations such as the ATRS mounted rocker pad deflector systems have been designed to improve the roof bolter operator safety. This paper will inform the reader of the hazards, machine evolution through different design solutions, and the current state of the art in preventing roof skin failure injuries when roof bolting.

Jan 1, 2009

By Axel Preusse

On the basis of the Law on Financing Hard Coal Mining dated 28 December 2007, the subsidized German hard coal mining industry will be shut down to the end of the year 2018 in a socially acceptable manner; in 2012 this decision will be reassessed. Even after the abandonment of all mining activities subsequent burdens are inevitable. In this paper, the possible long-term effects resulting from a mining industry history, which is spanning more than 200 years, and their possible consequences are pointed out, in particular in connection with the abandonment of mine water drainage measures which is economically meaningful in the long term. According to the decision situation as it presents itself today, this point in time will be far beyond 2018. In preparation for this, an action framework is to be developed in areas possibly affected.

Jan 1, 2008

By Barry Voight

The law [ ] where [ ] is a measurable quantity such as strain and A and cu are empirical constants, describes the behavior of materials in terminal stages of failure under conditions of approximately constant stress and temperature. Applicable to intact rock and rock masses, the relation may be extended to conditions of variable stress and cyclic stress, and may be used to predict time to failure. Applications in rock mechanics include slope and excavation stability and various topics in ground control.

Jan 1, 1989

By Michael Alber

Coal mining by the longwall method typically causes seismic events. This paper describes the research on mining induced seismicity around two specific longwalls at 1100m depth under several old longwalls. A local network featuring 21 geophones has been installed, underground core drilling and an extensive rock testing program were executed. A rock mechanical model featuring a multi-layer strata was created for use with numerical analyses. Seismic events were localized and three different event types are described. Focal analyses yielded distinct modes of failure. Those types are explained by different failure mechanisms, namely fault activation, remnant pillar punching and beam failure. The use of rock mass classification, rock mass strength criteria and in situ stresses together with 2D and 3D numerical analyses allows evaluating the findings from seismology approaches. Conclusions are drawn that the orientation of longwall with respect to the major horizontal stress orientation plays an important role in mine induced seismicity.

Jan 1, 2008

By Leigh J. Wardle

This paper describes a numerical method for calculating the three¬-dimensional stresses and displacements induced by tabular excavations in a rock mass consisting of parallel layers of distinct material properties. The method is based on the superposition of numerical solutions for elementary displacement discontinuities in a parallel layered rock mass. The method can be used to analyse complicated excavation layouts such as those encountered in room-and-pillar or longwall mining. The method can automatically take into account the effect of the earth's surface. The method offers an economic and efficient solution to stress analysis problems which cannot be adequately modelled using two¬-dimensional methods and for which the expense of three-dimensional finite element or general boundary element analysis cannot be justified.

Jan 1, 1984

By Tom Barczak, Julian Restrepo, Zach Agioutantis

"The Alpha Foundation for the Improvement of Mine Safety and Health, Inc. (Foundation) was established as part of a Non-Prosecution Agreement (Agreement) entered in December 2011 by the United States Attorney's Office for the Southern District of West Virginia, the United States Department of Justice and Alpha Natural Resources, Inc. (""Alpha"") and Alpha Appalachia Holdings, Inc. This Agreement was related to the explosion at Upper Big Branch Mine, an underground coal mine owned by Performance Coal Company, a former affiliate of Massey Energy Company, which Alpha acquired in June 2011. Pursuant to that agreement, Alpha agreed to establish a trust to fund projects designed to improve mine health and safety by providing $48,000,000 into the trust. The mission and vision of the Foundation are as follows:Mission: To improve mine health and safety through funding research and development projects by qualified academic institutions and other not-for-profit organizations.Vision: To enable miners in the future to be free of work-related injury or disease by the implementation of the results of the projects funded by the Foundation and undertaken by the best researchers from any discipline that can contribute.The focus of the research effort is not limited to coal mine explosion prevention, and in fact encompasses the entire spectrum of health and safety, addressing issues in both underground and surface mining operations in all mining sectors. Four major focus areas are identified (see Figure 1): 1) Health and Safety Interventions; 2) Mine Escape, Rescue, and Training; 3) Safety and Health Management and Training; and 4) Injury and Disease Exposure and Risk Factors.The Foundation is seeking to expand the knowledge base of mining safety and health information that can lead to resolving complex mining problems. To that end, the projects funded by this effort are designed to provide a spectrum of knowledge potentially encompassing the following:• Surveillance data - Collect and analyze surveillance data that better documents the prevalence and trends of occupational safety and health across the mining industry."

Jan 1, 2016