Search Documents

By Mostafa Sharifzadeh, Ebrahim Ghasemi, Kourosh Shahriar

"The Tabas Central Mine (TCM) is one of the underground coal mines located in the Tabas coal region, in the mid-eastern part of Iran. This mine is the first mechanized coal mine in Iran that uses the room and pillar method. Pillar design is one of the most important issues in underground coal mines, especially in room and pillar mining. In this paper, a new method for coal pillar design in the main panel of TCM is presented. This method is able to estimate the magnitude of the various loads (both development and abutment loads) that pillars might experience throughout the mining process. Also, the method reduces the pillar failure risk. Based on this method, proper pillar sizes in TCM are obtained (11.6 x 11.6 m (38.l x 38.1 ft)).INTRODUCTIONPillar design and stability are two of the most complicated and extensive mining problems related to rock mechanics and ground control subjects. Although these problems have been investigated for a long time, to date only a limited understanding of the subject has been gained. Prior to this, the dimensions of a pillar were largely determined by experience based on trial and error, intuition, or established rules of thumb; any research available tended to be isolated and sporadic. But nowadays, various pillar design formulas have been developed based upon laboratory testing, fullscale pillar testing, and back-analysis of failed and successful case histqries. In 1980, a number of ambitious field studies conducted by the U.S. Bureau of Mines developed the ""classic"" pillar design methodology. It consisted of three steps (Mark, 1999, 2006):1. Estimating the pillar load using tributary area theory2. Estimating the pillar strength using a pillar strength formula3. Calculating the pillar safety factorAlso, Bieniawski (1981) presented a step-by-step method to determine coal pillar dimensions in room and pillar mines. In this method, similar to the classic method, pillar load is estimated by using tributary area theory.Currently, in mqst of the room and pillar mines, remnant pillars in panels are recovered by retreat mining (pillar recovery). Hence, the above mentioned methods are not appropriate for pillar design, because in these methods pillar load is estimated by the tributary area theory, and the effects of abutment loads, which result from retreat mining and the creation of a mined out gob, are ignored. Abutment loads affect the pillars in the adjacent of pillar line and a load greater than what is estimated by tributary area theory is applied on the pillar. So, pillar design without considering the abutment loads leads to pillar failures during retreat mining. Pillar failures continue to be one of the greatest single hazards faced by underground coal miners. Pillar failures are responsible for unsatisfactory conditions, which include the following (Mark et al., 2003):"

Jan 1, 2010

By Takashi Sasaoka, Hiroshi Takamoto, Akihiro Hamanaka, Pongpanya Phnthoudeth, Hideki Shimada, Jiro Oya

"Indonesia is the second largest coal exporter to Japan, accounting for about 30 Mt annually. They produced over 400 Mt in 2015, over 99% of which is from open-cut mines. However, the conditions of surface mining are becoming worse year by year: the stripping ratio is increasing, the economy is worsening, and the infrastructure for coal transportation from inland mining areas is not being maintained. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. In consideration of growing need, our research program is conducting a study on the potential for an underground coal mine in Indonesia. This research is being done through the roadway heading research program, which is looking into developing an underground coal mine from an open pit highwall. The greatest challenge for underground coal mine development in Indonesia is the maintaining the safety of the mine roadway during heading because the roof rock is exceptionally weaker. There is a potential for heading below mobile, unconsolidated soft sediment, and instead mining a deep area. This increases the likelihood for problems in the stability of the support system due to increasing ground pressure. The ground behavior around the roadway was measured using telltales, extensometers, and convergence measurements. Moreover, rock property tests were also conducted on exploration drilling cores. Based on the geological dates and monitoring data, a series of numerical analyses were conducted in order to assess support needs in the main roadway under different depths. Results of numerical analyses indicate that the current arch support design is effective when the mining depth is lower than 100m. However, if the mining depth is larger than 100m, the current arch support design should be changed to include the application of higher yield strength material, shorter spacing, etc. Moreover, bolting may also be useful if ground pressure is high locally. Based on a series of measurement data of ground and support behavior, a control criterion for main roadways under weak geological conditions is proposed in this paper."

Jan 1, 2017

By Eric C. Poeck, Ryan Garvey, Ugur Ozbay, Kun Zhang

"A coal bump is characterized by the sudden failure of one or more pillars and an associated release of kinetic energy. Although the geologic conditions surrounding coal bumps are often similar, their occurrence and magnitude are difficult to predict. This paper presents the development of an approach to assess the potential for coal bumps in room and pillar mines through the use of energy concepts and special consideration of the interface properties between the coal and overlying rock. Back analyses were performed on the widespread collapse of a room and pillar mine with an associated 3.9 local magnitude seismic event. Pillar and mine-scale models were constructed using the distinct element method to simulate the mining stages leading up to the collapse. A variety of loading conditions, material properties, and interface properties were evaluated for their effect on unstable failure of single pillars, and the mine-scale model was used to study the evolution of failure during progressive mining. The extent of unstable failure was quantified in these models by calculating the total kinetic energy released during each mining stage. Through the parametric analysis of single pillar models, it was found that softening parameters in either the coal or the coal/ rock interface can individually facilitate unstable failure of pillars, but the combination of the two in a single model produced a much higher release of energy during failure. The results of the minescale model further illustrated the trend as the combination of softening parameters in the coal and coal/rock interface produced a series of failures that most accurately reflected the collapse event at the mine. The method of room and pillar stability analysis demonstrated in this study effectively explores the potential for large coal bumps.IntroductionThe analysis of coal pillar behavior is challenging because natural variability in geologic conditions requires estimation of material strengths and predicted loads for a given mining situation. Large width-to-height (w/h) ratio pillars and deep overburden present an additional challenge, as the failure behavior of such pillars is more complex and may involve unstable, sudden collapse. Empirical methods have improved the success of coal pillar design for a wide range of conditions, but, for deep cover and squat pillar (w/h > 10) geometries, pillar performance predictions are not as accurate (Mark, 2000). As with any empirical approach, more back analysis and the consideration of new variables may help improve understanding and accuracy of future designs."

Jan 1, 2015

By Eric Keller, Jamal Rostami, Wenpeng Liu

"Roof and rib instability is an important issue in underground mining. To optimize ground support design, enhance ground stability, and reduce the possibility of roof or rib failure with minimal use of artificial ground support, it is essential to have an accurate understanding of ground conditions. This includes the location of voids, cracks, and discontinuities, as well as information about the different strata in the immediate roof. This paper briefly introduces ongoing research on void detection by using the roof bolter feed and rotation pressure. The goal of this project is to improve the sensitivity of detection programs to locate smaller joints and reduce the number of false alarms. This paper has presented a brief review of the testing procedures, data analysis, logic, and algorithms used for void detection. In addition, this paper has discussed the results of preliminary laboratory tests and statistical analysis of the data from these two drilling parameters used for void detection.INTRODUCTIONRoof falls are one of the most serious and frequent accidents in underground mining. Each year, personnel are injured or killed because of roof falls. Equipment can also be damaged when this occurs. According to Mine Safety and Health Administration statistics collected from 1999 to 2008, ground falls were the largest cause of fatal accidents in underground coal mining, causing around 40% of all fatalities (NIOSH, 2015a). Out of 8 to 10 fatalities and over 800 injuries are recorded each year in underground mines, there are nearly 2,000 reportable non-injury ground falls every year (NIOSH, 2015b).Certain features in the ground, such as voids, cracks, and discontinuities, are significant factors that cause roof support failures and roof fall accidents. Currently, several manufacturers provide smart roof bolters with limited capabilities for void detection. While successful in many instances, in laboratory experiments, the existing void detection systems have limited success in detecting void openings that are less than 1/8 inch This limited success was observed in testing concrete blocks with gaps in between, simulating a rock medium with voids. Detection programs have missed some voids, while, in some cases, they have shown false detection. These algorithms need to be more accurate in sensing voids to improve the capabilities of these programs."

Jan 1, 2016

By Kudret Tutuk, Serkan Saydam, Sungsoon Mo

"This paper presents an overview of the floor heave management at the Glencore Bulga Underground Operations and investigates the contributing factors to the behaviour of the floor. The mine experienced a number of major floor heave events in gateroads on development. As the longwall face approached the roadways, the magnitude of floor heave frequently increased, while new floor heave also developed. Furthermore, severe floor heave events took place along the longwall face. The most observed failure mode was buckling. While regular floor measurements were conducted to better understand the nature of the phenomenon, and various measures were considered to control the deformation of floor, the mining height was increased for the predicted floor heave domains, which facilitated effective management of the floor issues. The experience in the mine indicates that mainly high horizontal stresses with greater depths of cover and certain types of floor lithology configuration are likely to contribute to the failures of floor strata.INTRODUCTIONThe Glencore Bulga Underground is located in the Southwest of Singleton in the Hunter Valley of New South Wales, Australia. Blakefield South, part of Bulga Underground, commenced longwall mining in 2010, extracting coal from the Blakefield seam, while the overlying longwall panels were previously mined from the Whybrow seam. The coal seam ranges from 4.5 m to 8.0 m thick with the mining heights varying from 2.9 m to 3.5 m. The longwall panels are 320 m and 400 m wide and up to 3.5 km long.The mine experienced a wide range of floor issues around longwall panels LW7 and LW8, both 400 m wide. For instance, the concrete floor in the travel road failed and lifted as the longwall retreated in close proximity as can be seen in Figure 1. Figure 2 shows the beam stage loader (BSL) buried into the lifted floor, and Figure 3 shows a timber prop distorted due to the movement of the floor. In addition, severe deformation of the floor along the longwall face impeded the longwall operation, as shown in Figure 4."

Jan 1, 2018

By Karsten Zimmermann, Peter Cain

"To receive regulatory approval for a new coal mining operation in North America, extensive investigations of feasibility and potential environmental impacts, including ground deformations, are required. Figure 1 shows pictures from mine sites and an example mine map with the planned panel layout for one seam of the multi-seam longwall operation considered.The cumulative mined coal thickness of 22 meters in some areas of the operation requires a comprehensive forecast of expected ground movements and subsidence impacts (e.g., subsidence, slope, displacement, curvature and strain). In the frame of the impact study, the prediction of these impact factors was conducted by DMT using the computer program SPS 4D, based on the Ruhrkohle modeling method by Ehrhardt and Sauer (1961).This paper briefly presents the modeling method and explains the benefits and possibilities for its international application. Information gathered from literature studies on subsidence in North America were incorporated into the initial model parameterization. The article shows the ways in which the observed influences of mountainous topography on surface displacements and deformations can be considered by an extension of the subsidence prediction model and integration of DEM information.SUBSIDENCE MODELFor the calculation of mining-induced subsidence and deformation, DMT has developed subsidence prediction software SPS 4D, which is built according to the stochastic prediction model by (Ehrhardt and Sauer, 1961). The model is based on the subsidence theory by (Knothe, 1953) with a specific parametrization of the stochastic influence function and includes enhancements for dynamic subsidence calculations after (Sroka, 1978). In Europe, mainly in Germany and Poland, the model is approved by the authorities as a standard model for subsidence prediction in mining areas. However, extensive research within R&D activities has shown the possibility to predict mining-induced subsidence considering the specific mining conditions in North America (Zimmermann and Fritschen, 2007)."

Jan 1, 2016

By Mark K. Larson, Douglas R. Tesarik, Heather E. Lawson

"Load transfer distance (LTD) is simple in concept and usually evident in underground coal mines. Many people in the mining industry recognize LTD as the distance from the panel to where the mine ribs and pillars show evidence of renewed spalling, floor heave, or other effects of increased weight due to longwall mining or pillaring. Barrier pillars, in particular, are designed to shield mains and other relatively permanent facilities from this loading. LTD is also important in determining the extent and degree to which mining increases the load on pillars and ribs in the gate roads. Generally, a long LTD reduces loads in gate roads, but may require larger barrier pillar widths to protect mains or adjacent panels from excessive loads. Therefore, a long LTD may make it easy or difficult to meet various objectives of mine layout design . LTD reflects overburden geology in two ways: First, overburden that is weak and readily caves will limit both the amount and distance of load transfer. Second, stronger, stiffer, sandier, and more massive overburden increases both the amount and distance of load transfer. As such, LTD is central to coal mine layout design and calibration of numerical models that seek to anticipate these transfers of load during mining. However, the term does not have a consistent definition in the literature, and various instruments and observational techniques with varying sensitivities and thresholds have been used to indicate the onset of mining-induced stress increase and, subsequently, to determine an LTD. Consistency is important for meaningful comparison of ground response between mining sites and for accurate calibration of models.This paper adds to the body of observed and reported LTDs by presenting cases with relatively sandy and massive overburden at two western coal mines. These two cases include observation and measurement of LTD with multiple methods and provide insight into how distances reported relative to different criteria and instrumentation could be adjusted for comparison against a common base. This base is the criteria used by Peng and Chiang (1984) to determine their empirical equation. In one of these two cases, LTD was recently measured at a western U.S. coal mine (Mine A) to be approximately four times that calculated using the Peng and Chiang empirical equation. LTD measurements were examined using various instruments at Mine A and at adjacent Mine B. The measurements at Mine B showed that LTD was significantly greater than that calculated by the Peng and Chiang equation. Difficulties with BPC installation and fittings at Mine B permitted only ranges of LTD to be determined from some BPCs. Even so, the LTDs and ranges of LTDs determined were consistent with the LTDs determined at Mine A."

Jan 1, 2015

By Soheil Bahrampour

Void detection and identification of bed separation while drilling holes in rocks for roof bolting can be a great source of information for the evaluation of ground conditions and adjustment of ground control or support measures. This can be accomplished through the monitoring and analysis of drilling parameters by the roof bolter. This paper reviews work currently under way in a joint study between Penn State University and J. H. Fletcher & Co. The detection of voids, along with identification of rock types, can lead to development of 3D roof maps, which can subsequently be used to evaluate ground support and its suitability for given ground conditions in tunneling and mining operations. Existing algorithms for void detection utilize the sensory information of the drill unit, such as feed and rotary pressure, revolutions per minute (RPM), and penetration rate, to detect voids or joints on the roof/ ribs. While the void detection algorithms are being revised to allow analysis of available data from the existing sensory systems of the roofbolters with higher accuracy and lower number of false detections, additional sensors have been added to the drill to improve its ability for accurate detection of the voids and joints. This includes installation of vibration and acoustic sensors on a drilling unit at J. H. Fletcher & Co., and pertinent data analysis which are discussed in this paper. Initial results indicate that the data obtained by vibration and acoustic sensors at high sampling rates can be used to improve the performance of the void detection algorithms independently, and when combined with the modified algorithms using existing sensors, it can substantially improve the capabilities of current void detection system.

Jan 1, 2013

By Enguang Zhu, Kangning Zhang, Yang Li

"Due to the use of outdated mining technology or room and pillar mining process in small coal mines, the coal recovery ratio is only 10% - 25%. In many regions of China: the damage area caused by the small coal mines amounted to nearly one hundred square kilometers. Therefore, special mining techniques must be taken to reclaim the wasted resource in disturbed coal areas. This paper focuses on the different mining methods by analyzing the longwall panel layout and abandoned gateroad (AG) distribution in in the abandoned area of Cui Jiazhai Coal Mine in northwestern China. On the basis of three-dimensional geological model, FLAC- 3D numerical simulation was employed. The abutment pressure distribution was simulated when the panel face passed through the disturbed areas. The proper angle of the inclined face was analyzed when the panel face passed through the abandoned gateroads. The results show that the head end of the face should be 13-20m ahead of the tail end. The pillars on both sides of abandoned gateroads had not been damaged at the same time, and no large-area stress concentration occurred above the main roof. Therefore, the coal reserves of disturbed areas can be successfully recovered by using underground longwall mining. INTRODUCTIONDuring the 70-90's, there were a lot of small coal mines in China. Due to their disordered mining, most of the small coal mines left a great many abandoned gateroads (defined as AG in this paper) and a large area of damage coal seam. In these type of coalfields, there exist many mining risk issues, including nonuniform stress in the overburden, flooding and hazardous gases accumulated in the gob. So how to lay out a longwall panel and successfully mining under this type of abandoned small mines is a big issue nowadays in China.As mentioned above, longwall panel is being performed in the damaged coal seams in order to increase recovery of coal reserves (Wang, 2009). However, the abandoned geteroads intersect to each other all around the area. So a series of production issues arose while the panel face is passing through these AG. Gang and Gong (2015) analyzed the roof stability and abutment pressure distribution during the face was passing those AG that were parallel and inclined to the faceline. Xie, et al. (2015) proposed the ground control mechanism by passing the AG in top-coal caving longwall mining. He recommended to stop the face advance until the roof is over, using high strength bolts and cable bolts, and grouting consolidation. This paper studies the different mining methods by analyzing the longwall panel layout and AG distribution in damage coal seams. Theoretical analysis and field observation were conducted to determine the overburden movement when the face was advancing under the AG. The pillar between face and parallel AG changes from elastic to plastic and eventually to the residual supporting status. All these three status was combined with the roof structure to establish the theoretical model to calculate the shield support capacity. Numerical modeling was employed to simulate the pillar stability and determine the abutment pressure distribution as the face inclined to the AG during longwall mining."

Jan 1, 2016

By John R. Poland, Benjamin Mirabile

"There are significant ground support hazards to both personnel and equipment when longwall equipment must mine through cross-panel entries. Backfilling support strategies are often cost prohibitive. Additionally, it is often very difficult to install backfill material in full contact with the mine roof in backfilled entries. This paper will demonstrate the use of fiber-reinforced concrete crib material as a method for standing support in longwall cut-through entries. Despite conceptions of poor performance in potentially high convergence environments, fiber-reinforced concrete crib material can be used in longwall support environments subject to high abutment loads and convergence. Central to the proper design of these supports is the use of yield material between crib layers and at the mine roof/crib interface. The placement location of cribs within the cut-through entry has a significant effect on the main roof behavior and associated ground conditions in the longwall abutment zones. It is particularly important to engineer the proper load displacement characteristics of the installed crib to support expected ground conditions. The cost of fiber-reinforced crib supports is less than 50% of backfilling methods.INTRODUCTIONThe design and execution of a longwall cut-through is perhaps one of the most difficult and risky endeavors in the field of ground control. The magnitude of abutment loads and potential for ground failure present a significant safety hazard to underground personnel. In addition, there is significant financial risk, with replacement costs of face equipment exceeding $200 million. Faced with these consequences, it is both advisable and common for an engineer to design ground support with a significant margin of safety. This paper outlines a robust support system that possesses a significant margin of safety along with significantly lower costs than most other support systems employed in similar conditions.SITE PARAMETERSThe mine site described in this study operates in the Herrin No. 6 seam in southern Illinois. The seam height is typically 76- 84 inches. Mining height in gateroads and mains is typically over 96 in, and typical mining height on the longwall face is 82 in. The overburden depth is 950-970 feet in the area of the longwall cutthrough."

Jan 1, 2016

By Ben Mirabile

Over the past three decades, the U.S. coal mining industry has widely used cable supports to supplement traditional primary bolting systems, especially in difficult ground conditions. However, increased mining activity in adverse conditions has underscored the limited effectiveness of the non-tensioned, partially grouted cable supports used to supplement primary bolts. Roof failures in conditions such as corrosive environments, highly laminated strata, low overburden depth and water intrusion have demonstrated that the need for cable technology has reached beyond the traditional non-tensioned, partially-grouted cable tendon. Furthermore, declining market conditions and increased competition for coal customers has demanded that new cable bolt technology be costeffective and readily adaptable to the mining cycle. Jennmar Corporation has developed several cable bolt technologies that can be used as stand-alone solutions or in concert with one another to mitigate adverse conditions. These technologies include rapid tensioning of cable supports, structural surface control and polyurethane injection. The case studies presented in this paper use one or more of these technologies to address adverse mining conditions or special ground control problems.

Jan 1, 2013

By Thomas A. Cook

The effectiveness of tensioned roof bolt systems has been well researched and documented over the years (Stankus, 1990, 1991, 1997; Guo, 1997; Denton, 2000; Su, 2007). Higher and more consistent installed tension has been shown to improve the beaming effect and associated roof stability especially in highly-stressed, weak, laminated roof strata. To accomplish higher and more consistent bolt-installed tensions, various types of anti-friction washers have been developed and applied to many types of tensioned roof bolt systems. In addition to increasing bolt-installed tension, these washers also provide a lubricating effect that minimizes sparking during the bolt torqueing cycle. The most popular and widely used anti-friction washer configuration consists of a plastic washer that is used in conjunction with a standard hardened steel washer. This washer configuration has performed well in the field in terms of increasing the bolt-installed tension (or plate load) and the related tension/torque ratio (the amount of tension achieved per one ft-lb of applied torque). However, the installed tension does not always maintain consistency. One reason for this inconsistency is that the plastic anti-friction washer sometimes dislodges and shreds or tears before the bolt torqueing cycle is complete. This condition prevents the plastic washer from acting as an anti-friction medium for the entire torqueing cycle. Jennmar Corporation and Keystone Mining Services, LLC, developed the ?TT? washer in early 2012. The ?TT? anti-friction washer is comprised of two zinc-coated (galvanized) hardened steel washers that are joined together with an exclusive polymer. The ?TT? washer has been extensively tested and applied in the Sewickley, Pittsburgh, and Indiana #5 coal seams. The test results indicate an average increase in installed load and tension/torque ratio of 20%. More importantly, the installed load consistency improved, with a significant reduction in the standard deviation of values. This paper will detail the development and testing of the ?TT? anti-friction washer with case studies of actual mine applications.

Jan 1, 2014

By Monte R. Hieb

Study of moisture-induced swelling strain in Pennsylvanian Period rocks of the Appalachian Plateau in West Virginia shows a 2:1 biaxial horizontal anisotropy which trends NW-SE. Oriented in-situ slabs of coal mine roof rock were collected across West Virginia, dry-sawed to size, air-dried to stability, and then monitored for moisture changes and deformations in the horizontal plane through one wetting cycle and drying cycle. Biaxial swelling strains were exhibited in nearly all rocks tested, with maximum horizontal deformations occurring normally-incident to the strike of regional geologic fold structures. This relationship persists as fold strike varies across the study area. A connection with Alleghanian fold development and/or post-Alleghanian fold relaxation is suggested. Deformations were largest in shales, but occurred in sandstones and siltstones as well. During testing, moisture-induced fractures (MIF) developed parallel to the regional fold structure and ranged in size from hairline cracks to sample-destroying cracks that were orthogonal to the observed biaxial swelling strain direction. Preferential wetting and swelling of clay minerals along NE-trending fractures, related to a fold-parallel fracture fabric of regional extent across West Virginia, is the most likely reason for the observed systematic NW-oriented biaxial swelling strains. The testing methods used in this study are simple and inexpensive and produce robust results that offer insight into a regional, anisotropic mechanical weakness that imparts a dynamic, asymmetrical horizontal stress to moisture-sensitive coal mine roof rocks over time. Because a similar mechanical fabric has been reported in Devonian-age shales, these findings may have implications for shale gas developers in the Appalachian Basin challenged by rapid aperture closure rates along horizontallydrilled induced fracture networks in Devonian rocks like the Marcellus Shale. The paper concludes with an example of how the concept of a preferred swelling strain direction might be applied to improve the effectiveness of roof trusses.

Jan 1, 2013

By Guy Reed, Russell Frith

"The method of determining coal pillar strength equations from databases of stable and failed case histories is more than 50 years old and has been applied in different countries by different researchers in a range of mining situations. While common wisdom sensibly limits the use of the resultant pillar strength equations and methods to design scenarios that are consistent with the founding database, there are a number of examples where failures have occurred as a direct result of applying empirical design methods to coal pillar design problems that are inconsistent with the founding database.This paper explores the reasons why empirically derived coal pillar strength equations tend to be problem-specific and should be considered as providing no more than a pillar strength “index.” These include the non-consideration of overburden horizontal stress within the mine stability problem, an inadequate definition of super-critical overburden behaviour as it applies to standing coal pillars, and the non-consideration of overburden displacement and coal pillar strain limits. All of which combine to potentially complicate and confuse the back-analysis of coal pillar strength from failed cases.A modified coal pillar design representation and model are presented based on coal pillars acting to reinforce a horizontally stressed overburden, rather than suspend an otherwise unstable self-loaded overburden or section, the latter having been at the core of historical empirical studies into coal pillar strength and stability.INTRODUCTIONThe inspiration for this paper is founded in three statements from two eminent persons in the field of coal pillar strength research, Jim Galvin and Essie Esterhuizen, as follows:Both Salamon and Munro and [the University of New South Wales] based the derivation of their pillar strength formulae on a criteria that the diameter of a panel of pillars, W, had to at least equal the depth of mining, H. This was thought to result in full tributary loading. It is now known that there are some mining environments included in both the South African and Australian databases in which mining span must exceed depth by a considerable margin in order to achieve full deadweight loading. Hence, it is logical to conclude that these data points may have contributed to pillar strength being overestimated by Salamon and Munro and UNSW (underline added by authors). Normally, this should be of no consequence because it is reflected in the probability of design success associated with any given safety factor (Galvin, 2006)."

Jan 1, 2018

By Zhikai Wang, Wensheng Lyu, Peng Yang

"To better understand the mechanical behavior of the compression deformation of backfill under high stresses corresponding to large depths, consolidation compression tests were performed for cemented tailings backfill with a cement-sand ration of 1:10 and 30% water under confined conditions. After applying different loading stress functions from 0.5 MPa to 32 MPa, the final axial deformation of the test specimen of backfill was obtained, and the micromorphology of backfill was studied before and after consolidation by scanning electron microscopy. Additionally, fitting analysis was performed for backfill confined compression deformation data and device model constitutive equations by the minimum square law. The constitutive model was revised according to the analysis results. The research results indicate that, as the load increases, the void ratio e obeys the functional relationship e=alnt + b (where a and b are fitting constants and t is compression time). Under the high-stress conditions of confinement, the constitutive model of backfill consolidation and creep can be used to describe the creep behavior of the backfill. Under high-stress conditions, after the consolidation of the confined backfill, the space between the tailing particles diminishes, the particles becomes more compact, and particle slippage occurs. INTRODUCTION With the depletion of shallow mineral resources, the mining industry has gradually shifted to deep mining (Zhang, Li, An, and Huang, 2010). Furthermore, with the continuous introduction of sustainable development policies regarding development and utilization of mineral resources, the mining industry must protect the limited available land and make full use of mineral resources as much as possible (Sijing, 1994; Zhihua, 2009). Backfill mining technology offers an unparalleled advantage in fully recovering mineral resources, controlling pressures, and improving environmental protection. As a result, this method has been widely used in various countries in the world (Burd, 2002; Benzaazoua, et al., 2008). Of the underground mines in the world, 45% of the large and medium-sized non-ferrous-metal mines and 37% of the gold mines use backfilling (Fuhrman, et al., 2014; Khaldoun, Ouadif, Baba, and Bahi, 2016). In addition, 45% of underground non-ferrous-metal mines and 37% of the gold mines use the filling method (Mchaina, Januszewski, and Hallam, 2001). According to incomplete statistics, more than 80 metal mines operate at a depth of more than 1 km; the depths of several typical deep mines are shown in Figure 1 (Burd, 2002; Fall, et al., 2009)."

Jan 1, 2017

By Yuanping Cheng, Jingyu Jiang, Qiang Zhang

"With the increase of mining depths, deep-seated coal seams face threats from high ground stresses, high gas pressures, high gas content, and low seam permeability, which significantly increase the likelihood of coal and gas outbursts. Challenges continue to grow in coalbed methane (CBM) extraction fields, especially for short-distance gassy multiple-seams. Research has proved that the most effective way to increase coal seam permeability is to decrease the ground stress. Protective seam mining technology is a surrounding rock control technology, which can effectively reduce the ground stress and increase the permeability of the protected coal seam. In this paper, we try to use upper protective seam mining technology to simultaneously extract coal and gas. Findings are based on a FLAC3D simulation of stress variation during the mining of the No. 12 coal seam in the Daxing coal mine, Tiefa Coalfield, China. Results indicate that, after mining the upper protective seam, the pressure-relief effects of the rock mass generated three belts and five zones below the protective seam, providing the space and time for gas pre-extraction engineering. Within the protected area, the numerical simulation indicates that the stress of the No. 13/14 coal seam reduces 95.84% and 88.25% respectively, while the expansion deformation of the protective seams reach 6.87 ‰ and 6.70 ‰ respectively, which demonstrate that the protective mining technology can provide a significant pressure-relief effect to the outburst-prone coal seam. Combining stress relief in this manner with pressure-relief from engineered gas drainage (performed by crossing boreholes from the floor rock roadway) applied before the mining of the protective seam, it would not only be beneficial to CBM drainage but also can reduce the gas outburst risk of the protected seams.INTRODUCTION Internationally, since France used protective seam mining technology to control coal and gas outburst in 1939, it has been promoted and applied in many countries (?????, 1966). Since 1958, China has taken the mining test and engineering practice of protective seam mining technology in the Beipiao, Tianfu, Nantong, Zhongliangshan, Songzao, Huainan, Huaibei, and other coalfields (Yu, 1992). Long-term theoretical research and mining practice of outbursts and dangerous coal seams show that protective seam mining technology is the most effective, safest, and most economical outburst prevention measure (Cheng, Fu, and Yu, 2009; Hu et al., 2008; Cheng and Yu, 2007). Under the condition of high gas content coal seams, the safety and efficiency of simultaneous extraction of coal and gas can be realized through a reasonable mining sequence and an effective gas extraction method (Cheng and Yu, 2003). The in situ stress distribution of the protective seam (No. 1 coal seam) and protected seam (No. 2 coal seam) during protective seam mining in the Haishiwan coalfield formation (Figure 1) (Li et al., 2014). A comparison of the stress and displacement (five zones and three belts) of the rock mass below the protective seam, and in a multiple-seam context in the Dalong Mine, is shown in Figure 2 (Jiang et al., 2015). After mining protection coal in a close-distance seam group, the small spacing between the coal seams causes the protective coal and the protected coal between part of the rock to crack through each other until the protective layer of gob is through the area. This provides a desorption of gas to the protective layer of the mining space channel, making the coal seam permeability increase to several hundred times and improving the gas discharge capacity (Zhai, 2008)."

Jan 1, 2017

By Marvin B. Thompson

"The depositional model for major Illinois Basin coalbeds is well documented and defined on a regional scale. The model was a driving force during past exploration for lower sulfur and thicker coal deposits. The most attractive coal reserves were known to lie along the flanks of contemporaneous sandstone filled stream channels and were overlain by thick silty gray shale roof. At various distances away from the channels, the depositional model transitioned to black shale I limestone roof, sulfur content of the coal bed increased, and the coal bed often thinned. Understanding the character of roof rock types associated with this depositional model is essential to predicting ground control factors on both a regional scale, and on resolving roof control problems at the mine-site. Additionally, horizontal stress and overburden depth are significant factors that impact roof rock quality and ground control in Illinois Basin mines.Determining the character of several rock types, and defining the primary horizontal stress direction were crucial to a recent successful project at New Future Mine, located in southern Illinois. An inclined slope was constructed from the Illinois No. 5 Coalbed up to the Illinois No. 6 Coalbed through strata that ranged from extremely weak ""stackrock"" and a weak underclay unit, to a massive sandstone unit. Engineering geology, operations management, and Jennmar technical services personnel teamedup to select and install roof support for each strata transition. The project was completed with no injuries and no roof falls.INTRODUCTIONAbundant published information concerning coal deposition, geographic distribution, quantity, quality, and mining conditions exists for Illinois Basin coal reserves. The State of Illinois, through its State Geological Survey (ISGS), has provided decades of research, record keeping, and service to the coal industry. Other excellent sources of Illinois Basin coal information include the Indiana Geologiq1l Survey and the Kentucky Geological Survey. Past research by the U.S. Bureau of Mines (USBM) supplemented the work by the geological surveys, especially in the area of horizontal stress and mining hazards. The National Institute for Occupational Safety and Health (NIOSH) continues to produce publications focused on roof control issues common to many coal basins, including the Illinois Basin. Many of the illustrations in this paper originated in ISGS and USBM publications."

Jan 1, 2010

By Richard R. Wilding

The United States Coal Mining Indus- try had the opportunity to greatly improve their roof control techniques during the nineteen seventies by the use of fully grouted resin roof bolts. This new tool was first approved for underground coal mines by M.S.H.A. ten years ago and during the next decade has been perfected to meet many problems previously thought to be unsolveable. The initial approved cartridge was very similar to the ones used in Europe in the nineteen sixties and since then has undergone a great deal of modification for our mines. These refinements in cartridge construction have been obtained by the close cooperation of resin manufacturers with mining personnel in perfecting pro- ducts customized to particular needs. This type of continuing program naturally necessitates a responsibility upon the resin anchor manufacturer to maintain a competant technical department. These roof control technicians by constant exposure to many of the most demanding underground problems, have developed through the years into leaders in successful applications. Today, Celtite has over twenty technically trained underground technicians with an accumulation of over one hundred years experience in resin anchors. Our documented technical reports are in excess of five thousand, involving over six hundred mines representing every major coal mining area in most mineable seams. This department has been the implement used to work with our research and development people in perfecting a continual line of improved resin anchors. This program has been a significant factor in leading the resin anchor industry into a position where approximately one third of the 1980 under- ground coal production used the fully grouted system. However, as gratifying as this accomplishment is, our experience has lead us to believe that there is an additional demand for a roof control system capable of combining the mechanical bolts ability to apply tension with resins proven superiority in anchoring. A significant number mines visited during the last decade had problems that we believed could be better answered by applying tension rather than the fully grouted approach. In most in- stances, their current mechanical installations were doing an adequate job until anchor slippage occured. Fully grouted systems solved this bleed-off problem. However, an acceptable number of falls still occured. In these some- what unique areas which we believe may amount to as much as fifteen percent of the total bolt installations, the need for improved anchors was a necessity. In developing this program we listed the ultimate requirements necessary for both the bolt and the anchor. These are for the bolt: A. Have one end manufactured so it can be grouted to the mine roof with polyester resin, obtaining a variable length from 12" to 36". B. Have a mechanism which allows the operator to tension the roof from zero to 10,000 psi. This mechanism should indicate if the roof is in compression and the bolt in tension. C. Have a mechanism which allows the operator to thoroughly mix the resin. D. The head of the bolt should not extend below the roof line any more than a normal mechanical bolt. E. Not require any extra tools for installation. F. Be bendable for use in low seam coal. G. Be durable and inexpensive. The ultimate point anchor resin should have the following characteristics: A. Have a mix and gel cycle which would compete with a mechanical bolt for speed of installation. B. Have a pull out strength in excess of a normal 5/8" mechanical bolt.

Jan 1, 1981

By Juan J. Monsalve, Nino Ripepi, Richard Bishop, Jon Baggett

"Terrestrial laser scanning (TLS) is a useful technology for rock mass characterization. A laser scanner produces a massive point cloud of a scanned area, such as an exposed rock surface in an underground tunnel, with millimeter precision. The density of the point cloud depends on several parameters from both the TLS operational conditions and the specifications of the project, such as the resolution and the quality of the laser scan, the section of the tunnel, the distance between scanning stations, and the purpose of the scans. One purpose of the scan can be to characterize the rock mass and statistically analyze the discontinuities that compose it for further discontinuous modeling. In these instances, additional data processing and a detailed analysis should be performed on the point cloud to extract the parameters to define a discrete fracture network (DFN) for each discontinuity set. I-Site Studio is a point cloud processing software that allows users to edit and process laser scans. This software contains a set of geotechnical analysis tools that assist engineers during the structural mapping process, allowing for greater and more representative data regarding the structural information of the rock mass, which may be used for generating DFNs. This paper presents the procedures used during a laser scan for characterizing discontinuities in an underground limestone mine and the results of the scan as applied to the generation of DFNs for further discontinuous modeling.INTRODUCTIONAccording to the Mine Health and Safety Administration (MSHA), between 2006 and 2016, the underground stone mining industry had the highest fatality rate in 4 out of 10 years, compared to any other kind of mining (MSHA, 2016). Additionally, during that same time, 40% of the fatalities were due to ground control issues, such as roof and rib collapses and pillar bursts. The National Institute for Occupational Safety and Health (NIOSH) developed guidelines for designing underground stone mines (Esterhuizen, Dolinar, Ellenberger, and Prosser, 2011). However, these guidelines do not apply to all underground stone mines.Monsalve, Baggett, Bishop, and Ripepi (2018) present a case study of an underground limestone mine experiencing a structurally controlled mode of failure. The authors analyze different methods to study that type of instability. They conclude that the integration of terrestrial laser scanning (TLS) with discrete element modelling (DEM) can be used to prevent rock falls in underground excavations to enhance worker safety. However, an adequate rock mass characterization and structural mapping must be performed in order to generate reliable models that allow the engineer to have a better understanding of the rock mass behavior."

Jan 1, 2018

By Dale A. Didcoct

Through the combined efforts of the C. S. Bureau of Mines, the coal industry, and Burrell Construction and Supply Company, New Kensington, PA, a steel fiber reinforced concrete crib block to improve coal mine safety in the area of roof control has been developed and is currently in use commercially. The development objective was to improve health and safety conditions with a stiffer, stronger, nonflammable roof support at a competitive cost. During the time this method of roof control has been in use in the mining industry, it has proven to be both functionally and economically effective.

Jan 1, 1982