Search Documents

By Xuchen Fan, Chenyang Zhou, Yuemin Zhao, Liang Dong, Chenlong Duan

A gas–solid fluidized bed using magnetite particles is an effective methodology for coal beneficiation in the field of dry coal cleaning. Broadening the size range of magnetite used in the bed decreases medium preparation cost. In this study, a tapered fluidized bed was used to investigate a magnetite particle size range of −0.5 + 0.074 mm. The results showed that a tapered fluidized bed effectively strengthens mixing of magnetite with a wide size range (−0.5 + 0.074 mm). The results of beneficiation experiments indicated that with increasing tapered angle, separation efficiency increased and then decreased. The highest separation efficiency was obtained at a tapered angle of 10°. The optimal results showed that the ash content of the concentrate decreased from 31.82% to 12.33% with a probable error of 0.11, which indicated that a tapered fluidized bed was efficient to improve fine coal beneficiation performance.

By F. Segobia, H. Lozano, M. Portal, F. Ysla, L. Goicochea

This case study evaluates the long- term physical stability of various historical mining structures remediated by the Center for Mining Environmental Research and Studies (CIEMAN) in Hualgayoc, Cajamarca, Peru. The region has a long history of mining activity, with remnants dating back to pre-Inca times. CIEMAN has assumed responsibility for remediating 286 environmental liabilities in the area, including adits, shafts, pits, tailings, and waste rock dumps. The study analyzes the methods employed to stabilize these structures, including geotechnical engineering techniques and revegetation. Long-term monitoring results are presented, assessing the effectiveness of remediation measures and predicting the future stability of the structures. This study highlights the importance of responsible remediation of mining environmental liabilities to ensure the safety and sustainability of communities and ecosystems affected by historical mining.

Feb 1, 2025

By Kazumasa Taguchi

At the Kakogawa works of Kobe Steel. Ltd., the agglomeration facilities are composed of a pelletizing plant and sintering plant. This aim is to utilize raw materials efficiently and stabilize the raw material resources. Therefore at Kakogawa works, the blast furnaces (BF) have been operated with high pellet ratio and various developments for pellet properties have been achieved to improve the blast furnace performance. These developments include dolomite-fluxed pellets, new-porous pellets and crushed pellets. As a results of these improvements, pellets have achieved almost the same performance as sinter at high temperature regarding properties such as the softening, melting and reduction behaviour. However, some problems on shape have remained to be solved. Spherical pellets flow easily into the center of the furnace and form mixed layers of pellets and cokes. Therefore, in BF operations with these pellets it becomes more difficult to keep proper and stable gas distribution.

Jan 1, 1983

By Liming Yuan, A. C. Smith

Barometric pressure changes affect air density, leading to change in the mass of the gas in the gob. When the barometric pressure decreases, the volume of gas in the gob expands, while the volume of gas contracts when the barometric pressure increases, a process which causes the gob to “breathe” out and in. Although the concept of gob “breathing” is simple, its effect on spontaneous heating of coal in the gob area is not clear. In this study, computational fluid dynamic (CFD) simulations were conducted to model the spontaneous heating of coal in the longwall gob area under measured barometric pressure changes. A single longwall panel using a bleederless ventilation system was simulated. If there is no barometric pressure change, the intake airflow rate is equal to the return airflow rate. When the barometric pressure changes, these two airflow rates are no longer equal, and the difference between the two airflow rates represents the airflow rate the gob breathes in and out. The effect of inflow and outflow of gas on the potential spontaneous heating in the gob was investigated using the CFD model developed in our previous study. The effect of barometric pressure changes on the spontaneous heating was found to be dependent on the gob permeability and the coal oxidation rate. The effect of barometric pressure changes on oxygen concentrations in the gob was also examined.

Jan 1, 2010

By J. Organiscak

A majority of continuous mining machines employ a water spray system and a machine-mounted flooded-bed scrubber to suppress and capture dust during coal mining. These machine-mounted dust control systems must be designed to function within the localized face ventilation system at the mining section to control both dust and methane. Spray systems can impede or improve the scrubber effectiveness in controlling dust or methane at the mining face. Laboratory experiments were conducted to examine the effect of spray type, spray pressure, machine body blocking sprays and scrubber airflow on dust and gas levels, while using a 12.2-m (40-ft) exhaust ventilation curtain setback from the face. These experiments were conducted with the mining machine positioned at the end of a simulated 6.1-m (20-ft) sump and slab cut. Results indicate that the hollow cone nozzles with blocking sprays best complement the flooded-bed scrubber performance in an exhaust ventilation system. This external spray system notably reduced dust and gas levels on the off-curtain side of the mining machine for both the sump and slab cut compared to the flat spray nozzles. Higher scrubber airflows reduced dust and gas levels on the curtain side and in the return of the continuous mining machine. The remote operator position, located on the off-curtain side and parallel to the inlet end of the exhaust curtain, sustained the most stable and lowest dust levels around the mining machine.

Jan 1, 2010

By M. L. Harris, I. Zlochower, M. J. Sapko, I. E. Perera

Experiments conducted with limestone dusts and dolomitic marble dusts have indicated that when rock dust is wetted and subsequently dried, it becomes a solid, non-dispersible cake. However, in order to be effective, rock dust must be able to disperse as individual particles to inert. To counteract this, rock dust manufacturers created treated rock dusts that will resist caking after moisture exposure. National Institute for Occupational Safety and Health (NIOSH) researchers conducted a series of laboratory-scale experiments on four base rock dusts and their treated counterparts to assess the effectiveness of various anti-caking additives after being exposed to moisture and then dried. The dusts were exposed to moisture using humidity cabinets having a high relative humidity (99% RH) and by also exposing the rock dust bed to water through bottom wicking. The dusts were then evaluated for dispersibility after drying using the NIOSH-designed dust dispersion chamber. The anticaking additives were different concentrations of stearic acid, oleic acid, and xylene-based surfactants. All results were compared to a reference rock dust used to conduct large-scale experiments in the Lake Lynn Laboratory (LLL), Fairchance, PA. When the untreated dusts were dried after exposure to moisture for one day, no dispersion was measured. However, rock dusts treated with anti-caking agents were readily dispersible even after exposure to moisture for six months. This report details the analysis and characterization of anti-caking additives using the NIOSH-designed dispersion chamber and the 20-L explosion test chamber. INTRODUCTION In order for a coal dust explosion to propagate, five elements are required. In addition to the fire triangle in which three elements are necessary to sustain a fire—fuel (coal dust), heat (ignition source), and an oxidizer (oxygen in air)—a combustible dust explosion requires dispersion of a dust cloud (pressure wave) and confinement of a dust cloud (underground mine entry) (1). Coal dust explosions can originate anywhere in a mine. For example, when a small volume of a flammable methane and air mixture is ignited in a closed end, the high-temperature gases rapidly expand to create a pressure wave, sometimes referred to as a “pioneer wave,” that may steepen into a shock wave as it propagates away from the ignition source. The shock wave produces a wind that disperses the dust preferentially from any elevated and exposed surfaces (roof, ribs, belt structure, cribbing, etc.). Factors that are known to affect the intensity of an explosion are the dust particle size, the location of the dust within the entry, the dust dispersibility, and the volatility of the coal dust (1). Particles less than 75 μm (< 200 mesh) in size are most reactive (2). Dusts that are located on the roof, ribs, and elevated surfaces are more readily dispersed than dusts on the floor. Therefore, application of quality rock dust in sufficient quantities is essential to inert coal dust and to prevent continued flame propagation. 30 CFR 75.402 and 75.403 require 80% total incombustible content be maintained within 40 ft of the face, and 30 CFR 75.2 defines rock dust acceptable for use in underground coal mines. It also defined that “when rock dust is wetted and dried, will not form a cake”.

Jan 1, 2019

By P. T. Bissert, L. Yan, M. D. Klein

"Federal regulations require that refuge alternatives (RAs) are located within 305-m (1000-ft) of the working face and spaced at one-hour travel distances in the outby area in underground coal mines in the event that miners cannot escape during a disaster. The Mine Safety and Health Administration mandates that RAs provide safe shelter and livable conditions for a minimum of 96 hours while maintaining the apparent temperature (AT) below 35°C (95°F). The National Institute for Occupational Safety and Health used a validated thermal simulation model to examine the mechanisms of heat loss from the RA to the ambient mine and the effect of mine strata composition on the final internal dry bulb temperature (DBT) for mobile tent-type RAs. The results of these studies show that most of the heat loss from the RA to the ambient mine is due to radiation (51%) and conduction (31%). Three mine width/height configurations and three mine strata compositions were examined. The final DBT inside the RA after 96 hours varied less than 1°C (1.8°F) for the three mine width/height configurations and less than 2°C (3.6°F) for the three mine strata compositions. INTRODUCTION Following a mine disaster, workers will try to escape the mine. If their escape is futile, they can take shelter in a refuge alternative (RA). In 2008, the Mine Safety and Health Administration (MSHA) mandated RAs in mines to ensure that a safe and livable shelter is provided for a minimum of 96 hours, and that the apparent temperature (AT) does not exceed 35°C (95°F) inside the RA [1]. An ongoing concern with RAs is the potential to exceed this limit. The temperature rise inside an RA is due to the metabolic heat released by the occupants as well as heat released by the carbon dioxide scrubbing system. The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type training unit RA in its Safety Research Coal Mine (SRCM) to investigate heat buildup in RAs. The 10-person capacity for the tested RA is based on 1.4 m2 (15 ft2) of floor space per miner. NIOSH-developed simulated miners, which are heat input devices that generate both sensible and latent heat, were used to represent the metabolic heat generation of an average miner (117 W) for testing in the SRCM. It was found that the number of occupants in an RA may need to be reduced based on the ambient mine temperature, which varies from mine to mine [2]. To further research temperature rise inside an RA, ThermoAnalytics, Inc. (TAI) was contracted by NIOSH to perform thermal simulations of the tested 10-person mobile tent-type RA. TAI developed a thermal model of the SRCM using RadTherm software, which incorporates a human thermal model (HTM) to represent the equivalent metabolic heat loss of a miner within the RA’s enclosed environment. The thermal model was previously validated by comparing simulation results with test results [3]. During a mine disaster in which miners would have to take shelter in an RA, mine ventilation may not be available. As such, mine ventilation was off for both the testing in the SRCM as well as in the simulations. This paper discusses the heat loss mechanisms and the effects of mine strata composition and mine width and height associated with a ten-person tent-type RA."

Jan 1, 2016

By Wolfgang Pietsch

DR iron&apos;) is a generic term for metallized product that results from the direct or solid state reduction of iron ore. In direct reduction, iron oxides are reduced to metallic iron in the solid state without an intermediate melting step. MIDREX ® Iron is the DR iron material produced in the MIDREX ® Direct Reduction Process. Except for some thermal and mechanical degradation, the external physical form of as-reduced DR iron is the same as the feed material. Chemically, oxygen associated with iron is removed leaving a very porous structure. Figure 1 is the scanning electron micrograph (SEM) of the internal surface of a MIDREX Iron pellet obtained from a Swedish oxide pellet during reduction at 760 °C. Figure 2 is the SEM of a polished and etched cross-section through the same pellet showing the amount of intraparticle porosity. As a result of this high porosity, apparent density of DR iron is relatively low, typically a¬round 2 g/cm3, and specific surface is extremely high, typically around 1.0 m2/g or more. Both density and specific surface depend on the raw materi¬al and the operating conditions of the direct reduction plant. Normally, more than 97% of the available iron is reduced into metallic iron with the rest mainly in the form of wustite (FeO). During direct reduction, the gangue in the iron remains essentially unchanged. Removal of oxygen and the corre¬sponding reduction in weight result in a slightly higher percentage gangue in the product than in the raw material.

Jan 1, 1976

By R. W. Smith

A number of investigators have studied the electrokinetic potential (?) of kaolinite as a function of pH. (1,2,3,4,5) These investigators all agree that the ? is negative except at quite acid pH values. The actual shapes of the curves reported by the several authors vary considerably. In spite of the general negative character of kaolinite the mineral has a rather high anion exchange capacity. (6,7,8) The cation exchange capacity is the lowest for the clay minerals. (6) It has been shown that anionic surfactants adsorb readily onto the mineral even up to neutrality, often in quantities exceeding the reported anion exchange capacity. (7,8) At least part of the anionic adsorption should be onto positive edge sites thought to exist on the mineral. (9,10) In the present study ? of kaolinite was measured as a function of pH using both the streaming potential (sp) and microelectrophoresis (m.e.p.) methods. In addition ? was measured at various pH values as functions of sodium dodecyl sulfate (SDS) and trimethyldodecylammonium chloride (TMDAC) concentrations. In some experiments decyl alcohol (DA) was added.

Jan 1, 1968

By Dominique Francois-Bongarcon

The world mining industry is facing a severe recession. Thus, it is time to recall the value of geostatistical methods which were formerly developed as a money-saving and productivity-increasing tool. The situation has worsened, but the techniques of geostatistics have dramatically changed. Up to millions of dollars can be saved during exploration with simple use of variograms; then, during reserves estimation with kriging methods; and finally, with the parameterization of reserves, when evaluating a project and optimizing its global mining parameters.

Jan 1, 1983

By K. A. Natarajan

Platinum electrodes are not inert as originally thought to be. The reactivity of platinum electrodes can explain their erratic behavior in many electrochemical measurements of metallurgical interest, e.g., in flotation systems, streaming potential measurements, contact-angle measurements, and in leaching systems. The anomalous behavior of platinum electrodes in redox potential measurements in aqueous systems was studied through Eh and pH measurements in water-oxygen, iron-water-oxygen and manganese-water-oxygen systems. Stability relations between Fe++ and Fe(OH)3 and between Fe(OH)2 and Fe(OH)3 were studied to judge the correspondence between experimental and theoretical equilibrium lines. The practicality of redox potential measurements in estimating ferric-ferrous ratios in aqueous systems was investigated along with their suitability as indicators in leaching operations, e.g., the removal of iron by aeration from manganese leach solutions.

Jan 1, 1970

By Jörg Holzhäuser, Matthew Crow

An 18.5 km (12 mile) long tunnel is being driven by four Earth Pressure Balance Tunnel Boring Machines (EPB-TBMs) of 4.7 m (15.5 ft.) diameter through alluvial sand, gravel, silt and clay above and below the groundwater table in Los Angeles beneath buildings, railroads, freeways and the L.A. River. Continuous automatic data recording of TBM operation and field inspectors&apos; records, accompanied by monitoring of 5,000 surface reference points and 268 borehole extensometers were used to obtain information. The paper explains the reason for selecting the method of EPB-tunneling to ensure stability of the tunnel and meeting of environmental requirements, and presents data collected to monitor and demonstrate the performance of the TBM sin the different ground conditions encountered.

Jan 1, 2003

By John N. Murphy

The past five years have seen communications techniques and hardware developed by the Bureau of Mines and its contractors increasingly brought into use in U.S. mines. The Bureau of Mines philosophy has been to help develop and introduce new hardware that goes as far as possible toward meeting the mining industry&apos;s needs. The Bureau of Nines programs are also designed to provide continuous fallout of new communications capabilities which are introduced to the mine operators as they occur. As more progress is made in meeting mine comnications needs, it is hoped that the mining industry will readily adopt the equipment and techniques that it finds most useful in meeting its individual needs. This paper reports on recent advances achieved in the development of improved nine communications systems.

Jan 1, 1976

By D. F. Boyd

On April 10, 1958 a new 7500 long ton/day iron ore beneficiation plant went on stream producing an average of 3000 long-tons of high quality concentrate a day. Plant operates on two, 12-hour shifts is six days per week, The new mill end crust ink plant were built adjacent to the company&apos;s open pit dining operate on at Bomi Hills, Liberia. The mall is essentially a gravity concentrator employing crushing, and grinding to liberate the mineral values, followed by concentration in Humphreys spirals. The cleaner spiral tailings are re-ground and tabled to recover additional iron values. Ire addition to. this mills the company operates a crushing and screening plant for the high grade direct shipping ores

Jan 1, 1962

By G. Paul Anderson

Personnel at Utah Copper Division&apos;s Bingham Canyon Mine use current computing technology to compile pertinent production statistics and mining plans. Within hours after the day&apos;s work has been completed, concise reports summarizing the previous day&apos;s production statistics, actual production vs. budget statistics, the location of shovels relevant to the mining plan, the performance of equipment, equipment next scheduled for maintenance, etc. are available at the terminals located throughout the mine. Also, engineering personnel us e computerized systems, directly from their offices, to assist them in the timely development of mining plans. Timely and concise reporting and planning capabilities such as these assist mine personnel in their efforts to review mining progress and equipment performance, and as such they are in a better position to detect adverse trends early and to seek appropriate resources or make changes in plans or practices.

Jan 1, 1977

By M. A. A. de Klaver

Due to the current cost and availability of crude oil in Brazil, Samarco Mineracao S. A., as part of its program of quality and productivity optimization and reduction of operating costs, has undertaken tests to utilize alternate energy sources for fuel oil used in its pelletizing plant at Point Ubu, Espirito Santo, Brazil. The energy program undertaken by Samarco consists of two basic steps. The first step was to reduce energy consumption, that is, to improve the thermal efficiency of the process. Secondly, a program was started to substitute the fuel oil with coal.

Jan 1, 1984

By James S. Redpath

"The ways of the world be many and most of the ways be tried, you follow in the footsteps of others till you come to the great divide". These words, written by Robert Service a long time ago, come to mind when I think of our original attitude upon entering into a contract with the International Nickel Company to sink the deepest shaft in the world outside of the Union of South Africa. This shaft was to be sunk to a depth of 7,137 feet from surface, and while it was recognized by all concerned to be a somewhat unusual undertaking in our part of the world, the fact that quite a few shafts had already been sunk to this depth in South Africa probably gave us the feeling that we were following in the footsteps of others. In retrospect, because this shaft was being sunk under entirely different conditions than those existing in South Africa, we were in fact venturing into an entirely new area of endeavour without properly recognizing this fact. It has occurred to me that others considering a similar type of job could benefit from our experience, especially in an assessment of the risks involved and how they compare to those encountered in an ordinary shaft. For comparison purposes, I would define an ordinary shaft as being sunk to a depth of 5,000 ft or less, and a deep shaft as one being sunk to a depth of between 5,000 ft and 8,000 ft. The sinking of the Creighton No. 9 Shaft has been de-

Jan 1, 1997

By Richard E. Gray

Virtually all structures show some signs of distress due to deterioration of the building components, to changed loads, or to changed support conditions. Changed support conditions result from ground movements. In mining regions many cases of structural distress are attributed to mining without considering alternative causes. This is particularly true of coal mining since it occurs under extensive areas. Coal mining is estimated to have already undermined more than eight million acres and may eventually undermine 40 million acres in the United States (HRB Singer, Inc., 1977). Other nonmetal and metal underground mines impact much smaller areas. Although it is sometimes difficult, even with careful study, to identify the actual cause of damage, persons responsible for underground coal mining should at least be aware of possible causes of building stress other than mine subsidence. This paper presents information on distress to structures and briefly reviews a number of causes of ground movements other than subsidence: Mass movements, dissolution, erosion, frost action, shrinking and swelling, yield into excavations and compressibility

Jan 1, 1986

By W. T. Walter

High-G centrifuges from five preparation plants were sampled to determine and quantify the various operating factors affecting performance. The operating factors that were considered include feed rate and percent solids, size of feed material, screen-basket type, hardness of coal and age of the flights. The performance parameters that were measured include product surface moisture, recovery and degradation of the coal. Regression equations with good significance levels were developed.

Jan 1, 1982

By Lu Yang

In the last two decades, acid iron ore pellets have established their predominant position as the iron-bearing burden material for blast furnace ironmaking in North America. It is a general practice that pelletization plants are asked to produce pellets of certain chemical composition and in a narrow range of sizes. A minimum amount of fines created during handling and transportation is desirable. Such a requirement is often expressed indirectly by the minimum compression load causing a pellet to break. The behavior of pellets inside a blast furnace, of course, is very important for a smooth and efficient operation. Before its melting in the lower part of a blast furnace during this period of several hours the behavior of pellets depends on their properties after induration as well as conditions inside each furnace. Among properties of indurated pellets, the ability to maintain their physical integrity in the burden and to be reducible are most important. To maintain the integrity of pellets (i.e., minimal low temperature breakdown, swelling and softening) so that there will be adequate overall permeability for certain wind rate and local permeability for gas/solid contact for reduction. A higher reducibility will moderate the adverse effects of swelling and softening and contribute to a smooth operation and efficient use of heat and reductants in a blast furnace. An article devoted to the relationships between the quality of iron ore pellets and blast furnace practice has been published elsewhere(1); therefore, no further discussion is needed here. The mechanism of strengthening of iron ore pellets during firing has been the subject of investigation of many authors(2). There is no doubt that the bridging of the growing hematite grains, particularly starting with magnetite concentrates, is very significant in the production of strong pellets. Recently, there are many reports from blast furnace operators that they have noticed the adverse effect of LTB in their plants. It is obvious that the strength derived from bridged hematite grains may disappear when hematite is converted to magnetite with thorough breakdown of grain structures. It is suggested that some other strengthening mechanism may be required in order to improve the LTB index of acid pellets. The influence of porosity on both compression strength and reducibility follows regular patterns. It has been suggested(1) that the amount of liquid slag in pellets during firing determines to a large extent the porosity, hence, indirectly, strength and reducibility.

Jan 1, 1983