Search Documents

By W. Burger

In underground mines worldwide, a large number of short and small diameter slot holes need to be excavated. Herrenknecht has developed and built a new boxholeboring machine based on the well-proven Microtunnellingpipe jacking technology. The innovative Boxhole Boring Machine significantly increases work safety and requires only minimal drift dimensions. The high and consistent production rates that can be achieved result in enormous time savings compared to conventional drill and blast excavations. GENERAL ASPECTS In gold, copper and ore mines ventilation shafts are required to prepare block caving operations, to discharge ore onto the transportation level and to provide evacuation shafts. A high level of occupational safety and efficiency is the main objective when drilling vertical or inclined shafts. The faster and more safely shafts can be constructed, the earlier the actual production in the mine can start or be continued. Mechanized or conventional methods (drill&blast) that have been used to date only partially meet the required safety standards and fail to provide the requested production rates.

Jan 1, 2012

Tracer gases are an effective method for assessment of mine ventilation systems, but their dispersion characteristics can differ substantially as ventilation parameters, such as flow path and velocity, vary. This research utilizes Computational Fluid Dynamics (CFD) to model a simplified full scale model mine, details a sensitivity study examining mesh size for an underground coal mine simulation, and examines gas dispersion parameters to determine the optimal model methods for simulation of tracer gases in underground coal mines. These models can be used to determine how a given tracer gas profile might be generated in a mine or areas of a mine that are not accessible, for example, immediately following a mine disaster. Accurate simulation scenarios can allow for the remote determination of the status of the ventilation network, but the sensitivity of the simulation at mine scale must be carefully examined.

Jan 1, 2012

By Mohamed A. Younis, Paul J. Headland, Paul H. Madsen, Vojtech Gall

INTRODUCTION A 100 ft long, 20 ft high and 18 ft wide NATM tunnel was excavated through grouted clean sands beneath a busy city street, including a variety of existing utility lines. The new tunnel associated with a hospital expansion will serve as a pedestrian tunnel connecting a parking structure with a new hospital facility. Tunnel construction started on December 15, 2005 when drilling for the grouting program started and was completed on May 26, 2006 when the tunnel final lining was completed. The tunnel was constructed by Kiewit Construction Company as a tunnel subcontractor to The Christman Company who is constructing the hospital facility for Spectrum Health in Grand Rapids, Michigan. URS was the project designer. GallZeidler Consultants, LLC were the contractor’s NATM consultant. PROJECT DESCRIPTION The Michigan Street Pedestrian Tunnel is a component of the Michigan Street Development located along the north side of Michigan Street NE between Coit Avenue NE and North Division Avenue in the downtown area of the Grand Rapids, Michigan. The Michigan Street Development includes a parking deck and four new towers to be constructed over the proposed parking deck. The tower planned furthest east is being developed by Spectrum Health as the Lemmen-Holton Cancer Pavillion. The purpose of the pedestrian tunnel is to connect the proposed Lemmen-Holton Cancer Pavillion with the future Spectrum building to be located on the south side of Michigan Street NE. The southern end of the tunnel was constructed with a bulkhead until the future Spectrum building is constructed at which time interconnection will be required. The tunnel site plan and profile are shown in Figure 1, Site Plan, and Figure 2, Tunnel Profile. Several challenges were faced during the design and construction of the Michigan Street Pedestrian Tunnel. These challenges included compressed design and construction schedule, maintenance of traffic and protection of old underground utilities. The tunnel was being constructed as part of the Michigan Street Development and coordination with other concurrent construction activities was required. The tunnel was constructed within a specified window of time to allow other associated construction activities to take place without compromising the overall project schedule. The design started in June 2005 and construction was completed by June 2006.

Jan 1, 2007

By Hans Hamrin

Three drill-blast cycles of 3.1 m advance achieved in one working shift of 7.5 hours at the Holsfjorden Tunnel project in Norway. The tunnel, 5235 m long, with a cross section of 8.6 m2, was completed several months ahead of schedule. This remarkable performance was achieved by a crew of 16 men, using machines specially designed for small tunnel excavation. The integration of drilling and charging into one unit, mucking and transport in another, reduced non-productive time considerably. The average cycle time of 140 min made it possible to complete three rounds in one 7.5 hours shift.

Jan 1, 1987

By Ching-Liu Wu, John Hawley, Andrew H. Liu, James Chai

The Hatch Mott MacDonald/Bechtel Joint Venture team is designer and construction manager for the 5.25-mile Tunnel Segment of the overall 16-mile Silicon ValleyRapid Transit Project, which extends the existing Bay Area Rapid Transit (BART) system southward from Fremont to San Jose. The Tunnel Segment includes twin boredtunnels, mined cross passages, and three deep station excavations situated in highlyvariable ground, high ground water table, and a dense urban setting with high-risebuildings adjacent to the largest excavation. This paper will discuss design challengesthat have arisen with the excavations and the proposed solutions.

Jan 1, 2007

By R. W. Carn, D. Vincent

Environmental Considerations With significant increases in bulk coal movements through terminals, operators are under constant social and political pressure to reduce or remove environmental pollution problems incidental to their operations. To meet these requirements, both equipment manufacturers and terminal designers are endeavoring to design equipment and systems with stringent environmental controls. The most challenging environmental problems facing coal terminal designers and developers are terminal siting restrictions, dust control, and noise abatement. Terminal Siting Finding a suitable site can be a difficult problem because of public concern over coal dust or the impact of a terminal on the surrounding community or natural habitat of the area. Often the only suitable flat land available for terminal development is on a tidal estuary or salt water marsh with great environmental value. In many cases a period of four to six years of full environmental and social assessment has been needed. A recent example of such difficulties is the expansion at Roberts Bank, British Columbia, where environmental impact assessment studies and their public review took almost six years from initial expansion applications until the time of approval. Dust Control Modern coal terminal dust control techniques usually consist of water sprays at strategic locations to suppress dust. The application points include rail car or barge dumper, main conveyor transfers, perimeter sprays around stockpiles, stacker/reclaimer, ship-loader transfers, and loading spout. The water sprays may include a chemical wetting agent or surfactant to reduce the water requirement and increase effectiveness. Recently there have been advances with development of effective micro foam agglomerating agents. In these systems, a micro foam with very small bubble sizes is sprayed into the coal stream. The foam fills the interstices between coal particles and wets the coal fines. These systems have proven to be very effective and usually one application before stockpiling and one upon reclaiming will markedly reduce the coal dusting. Stockpile perimeter sprays can be operated either manually or at the sophisticated terminal, actuated by a computerized control system that senses key environmental conditions such as humidity, precipitation, and wind velocity. Most modern terminals collect the drainage from the stockpile area, remove the solids in settling basins, then recirculate the water to reduce water requirements and effluents from the site. Dusting of long-term storage stockpiles can be reduced by spraying the piles with chemical resin or latex binding compounds to seal the surface. These compounds also can minimize erosion of the pile by rainfall. Dust collection with air evacuation systems and cyclone or wet scrubbers can be used at key areas such as rail car dumpers, main conveyor transfers, and ship-loader spouts. The trend in dust control is away from dust collection since most dust collectors are high maintenance items requiring good operator supervision and servicing. Coal handling conveyors are usually open and uncovered. However, in areas requiring special attention they may be covered or even completely enclosed. Dust generation from terminal roads is often a significant amount of the total dust emitted from a terminal. To reduce this dusting, roadways where traffic is heavy can be paved or sprayed by water trucks. Speed limits can be enforced and use of tracked mobile equipment for stockpile handling rather than rubber-tired loaders is encouraged by authorities. Noise Abatement Terminals located close to residential areas are often faced with noise control problems. Noise can be one of the most difficult environmental problems to solve. Usually, use of electrically-powered equipment is encouraged to reduce noise levels. Rail car dumper houses can be totally enclosed to reduce both dust and noise emissions. Diesel locomotives can be fitted with special muffling devices. Green belts of trees surrounding a terminal or the ap-

Jan 7, 1983

By Osvaldo Bascur, Barun Gorain, Jaco Steyn

"The last few decades have seen some remarkable advancement in information technology, but recently various digital technologies have resulted in several synergies to deliver innovation in diverse applications. The mining industry has been relatively slow in adopting these technologies compared to the other industries, but this scenario is changing fast.Challenges. Mining companies globally are going through a series of challenges such as declining ore grades with complex metallurgy, increasing depth of ore bodies, high capital and operating costs, lower productivity, shortage of technical resources, significant pressure from stake-holders to deliver, along with growing environmental and corporate social responsibility issues. Improvement in profitability would need significant improvements in operational performance.Consequently, over the last few years, there has been a major focus among some mining companies to imbibe operational excellence. This has been only possible because of the replacement of a silos-based approach by an integrated view of the organization. Such an integrated view is now possible via the evolving digital technologies. Even so, such a transformation calls for a change in culture, which, for most organizations is not trivial. Attempts in the past to integrate functions, such as through mine-to-mill initiatives in the mining industry, have demonstrated significant benefits to many operations (McKee, 2013). Still, sustaining these benefits has clearly been a challenge due to manpower turnover and lack of proper systems and structures that integrate information between business functions within an operation and between operations and the corporate level.Opportunities. The advent of digital technology has opened up opportunities to integrate interdepartmental information for a unified understanding across an entire organization. The advances in instrumentation, equipment control systems, supervisory control systems (SCADA/ Historian) and industrial networks have helped in the direction of enterprise- wide integration. The availability of real time information across an enterprise has given rise to numerous possibilities to improve organization performance. As suggested by Seshan and Gorain (2016), some of the potential opportunities are as follows:"

Jan 9, 2018

By Min Chen, Qinghua Liang, Weishan Yan, Yuan Feng, Shigang Wang

Various coal mine robots (CMRs) and unmanned aerial vehicles (UAVs) are implemented to explore unknown mines for improving the safety and efficiency of mining. It is challenging for CMRs and UAVs to achieve accurate positioning due to the absence of GPS, poor lighting conditions, and similar geometric features in complex mine scenes. LiDAR-based localization and mapping methods are admittedly more accurate than others, while long-time running in large-scale scenarios will also introduce non-negligible cumulative errors. This study presents a semantic-aided LiDAR simultaneous localization and mapping (SLAM) with loop closure, which leverages the uniqueness of mine intersection structure to establish stable semantic loop closure. Specifically, we propose a semantic intersection descriptor of translation and rotation invariance, which encodes 3D point clouds of the same intersection from different positions and viewpoints into a unified image. By using the semantic descriptor, we can construct a constant loop constraint when the same intersection is revisited from different directions to reduce cumulative drift. We provide experimental validation using large datasets collected in two large underground mines, namely, a simulated Edgar mine deployed in ROS Gazebo and a public underground mine dataset provided by ETH. Experimental results show that the proposed method has higher localization accuracy and outperforms the existing LiDAR-based SLAM strategies.

Aug 10, 2023

By Martin Herrenknecht, Karin Bäppler

The last five years have seen a remarkable increase in tunnelling projects in both soft ground and hard rock applications. Part of the increase is a result of recent Research & Development efforts to improve Tunnel Boring Machine (TBM) adaptability, capability and reliability. This paper will review the latest innovations in the TBM industry and explain in detail the results of these innovations followed by a forecast where the technology will take the tunnelling industry in the future.

Jan 1, 2005

By Patrick J. Doig

The contract for the construction of the Inline Pump Station for the Milwaukee Metropolitan Sewerage District involves the sinking of three shafts and the excavation of a pump chamber. The shafts are being sunk to a depth of 104 meters and pass through 52m of sediments before encountering dolomitic bedrock. The pump chamber is constructed in dolomite. The sediments are alluvial, estuarine and lacustrine in origin, with some ice margin deposits. They comprise loosely consolidated fine to coarse grained sand, silts, clays and gravels, and they are heavily saturated with a water content often above 60%. The water table is at a depth of 3m. The dolomite is silurian, generally dense, with some clay-filled vugs and shale partings. Until 1983, underground construction in the Milwaukee area had been limited to depths of 26m in the sediments and 20m in the dolomites. Water control methods had included caissons, compressed air, extensive internal and external dewatering, and grouting. Flows of 20 liters per second were commonplace with as much as 80 liters per second being encountered in the rock. However, in 1984 work was commenced on the deep sections of the Milwaukee sewerage scheme with the letting of three major contracts including the Inline Pump Station. With excavation taking place at greater depths, it become obvious that previous methods of water control would be inappropriate. To protect against major inrushes of high pressure water in the rock, an extensive program of pre-grouting from the surface was specified. Water control in the sediments was left to the discretion of the contractor and in each case freezing was choosen. This paper describes in detail the grouting and freezing procedures.

Jan 1, 1985

By V. T. McLemore

Deposits of rare earth elements (REE) are found in NM, but they have not been important exploration targets in past years because demand has been met elsewhere. However, with the projected increase in demand and potential lack of available production from China, the New Mexico deposits are being re-examined for their potential. REE-Th-U veins are found in the Gallinas, Caballo, Capitan, and Cornudas Mountains and Laughlin Peak-Chico Hills. Past production of bastnaesite has come from the Gallinas Mountains. Carbonatites are found in the Lemitar and Chupadera Mountains, Laughlin Peak-Chico Hills, Lobo Hill, and Monte Largo (Sandia Mountains). Although carbonatites have not been found in the Gallinas Mountains, they are suspected to occur in the subsurface based upon mineralogy/alteration. Disseminated Y-Zr deposits in syenite are found at Pajarito Mountain, Mescalero Apache Indian Reservation near Ruidoso. In 1990, Molycorp, Inc. reported historic resources of 2.7 million short tons grading 0.18% Y2O3 and 1.2% ZrO2 as disseminated eudialyte. Two additional deposit types have potential for REE in New Mexico: Cretaceous heavy mineral, beach-placer sandstone deposits and pegmatites. Exploration is ongoing in the Lemitar, Gallinas, and Cornudas Mountains.

Jan 1, 2012

Sustainable development is at odds with reality in the minerals industry. Increasing world population and aspirations are leading to increased energy and mineral consumption. Non-renewable fossil fuels are being exploited at a much faster rate than they are being discovered. Mineral reserves are diminishing and of lower grade. Despite recycling, many of the economic reserves of the rarer metals on which technological society has come to depend are being depleted, and many of the bulk metals are being exploited at ever increasing rates. And yet, mining continues, with a long-term downtrend in commodity prices, matched by more efficient mining and processing. Will society turn to a low carbon economy before fossil fuels are depleted? Will prices come to better reflect the full cost of mineral production? Will technology save us, or is it at the root of the problem? The key drivers continue to be an ever increasing aspirational population and the law of supply and demand, rather than sustainability considerations. The paper illustrates this with examples of worldwide and Australian data.

Jan 1, 2011

By S. Sunkavalli

Acid rock drainage (ARD) is produced when sulfides are exposed to oxygen and water. Oxidation reactions typically result in a depression of pH and leaching of solutes and metals. Many oxidation models have been developed based on oxygen diffusion, but in environments with high permeability, other transport processes (i.e., convection and advection) can play an important role. Multiple sulfide mineral phases with differing oxidation rates should also be incorporated. WROC, a finite-difference model, was developed to account for these factors in predicting ARD. The program includes sulfide mineral oxidation using a shrinking core mechanism, heat transfer by conduction, heat of reaction, and oxygen transport by diffusion and advection. The model was validated using data from the literature. After validation, the WROC model was used to simulate several different waste rock scenarios including different forms of sulfide mineralization and the effect of implementing a waste rock cover. The results demonstrate that including specific sulfide mineral phases can have a significant effect on oxidation and that implementation of a cover can also aid in reducing waste rock oxidation. Key words: Arsenic sulfides, oxidation, shrinking core, waste rock, oxygen transport

Feb 27, 2013

By J. Torma-Krajewski, M. Lehman

In 2005, NIOSH and Badger Mining Corporation entered a partnership to implement ergonomic interventions, including a systematic process, to address exposures to risk factors that may result in musculoskeletal disorders or other types of injuries/illnesses. As a result of this partnership, an ergonomics process was integrated with the existing safety and health program to promote an on-going application of ergonomic principles, and over 40 task-specific interventions were implemented during the first year of the process. This paper presents details of the process integration, and several examples of task-specific interventions that reduced exposures to risk factors.

Jan 1, 2007

By A. Korchevisky

Environmental self-monitoring is one of the advanced approaches for industrial sustainability programs. Organization for Economy Cooperation and Development (OECD) defines self-monitoring as ?the system of organizational and technical measures put in place and financed by [the] regulated subject? in order to ensure their compliance with regulatory requirements?1. Self-monitoring is beneficial for industrial operators, communities, and governments. Industrial companies use self-monitoring as a central element of their compliance management that allows them to fulfill their duties, obligations, and to avoid citations. When industries control their emissions and ensure workers are not exposed above the regulated limits, communities are better. It is impossible for an EPA, OSHA, or MSHA inspectors to be close to every emission source or workplace full-time. It is much more effective for industries to self-monitor, under due supervision. Occupational conditions are a very important part of industry and health and safety self-monitoring should be highly prioritized. In this paper we will research the regulatory basis and best practice of occupational self-monitoring. We will show that not only is self-monitoring a vital element of an occupational health & safety management system, but that you need a management system for affective monitoring.

Jan 1, 2012

By R. R. Oder, R. E. Jamison, E. D. Brandner

This paper presents preliminary test results obtained with a 0.38 kg/s (3000 lb-hr) beta prototype MagMill™. In processing Upper Freeport coal the beta prototype recovered 82% of the weight of the feed and 91% of the heat content while reducing the potential emissions of sulfur, kgSO2/GJ(lbSO2/MBtu), by 61%. Pyritic sulfur in the MagMill™ product was reduced by 78% compared to that in the feed. For all runs, the mill product was controlled between 70 to 80% finer than 74 µ particle size. Recoveries of mercury, arsenic, and selenium ranged from 35 to 45% of that in the feed. Power draw was reduced by 26% and mill throughput was increased by 9% compared to the pulverizer operating with no magnetic separator attached.

Jan 1, 2000

By Jenny Alsén, Hans Hogard

"Construction of large facilities underground in urban areas has many advantages. In order to show the advantages, a case study of the Norsborg metro depot in Stockholm Sweden has been made. The Norsborg metro depot will be the largest and most modern underground metro depot in northern Europe. The depot has been built in hard rock in an urban area with small impact on the environment and local residents. The paper describes how it is possible to build underground facilities in a cost efficient way and take care of the challenges regarding working environment that comes with locating a permanent working place underground. INTRODUCTION The Stockholm area is one of the five fastest growing regions in Europe and home to more than a fifth of Sweden's population on just two percent of Sweden's surface. The population is growing rapidly, with about 35,000 people per year and is expected to reach 2.6 million in 2030. In order to meet the development and enable continued growth, housing projects and expansion of infrastructure need to keep the same pace; this is an easy conclusion to make but much more difficult to realize in practice. The main challenge is to accomplish development in a sustainable and efficient manner, minimizing the use of resources and land. By constructing facilities underground more urban space will be made available for development and/or for greening of city centers. Considering sustainability factors such as land value in decision making for placing of structures or facilities, underground locations could become a first choice alternative. During 2015 and 2016, several major underground infrastructure projects in the city of Stockholm will start, including a 14 km sewage tunnel and an 18 km by-pass highway tunnel. Furthermore the Stockholm metro system is currently undergoing the largest expansion since the 1970’s, a 19 kilometers extension of the metro system including new trains and new stations is planned. During 2013 - 2015 Skanska Sweden took part in the construction of a new metro depot placed underground in the southern part of Stockholm; the Norsborg metro depot. This is a top modern urban underground facility that in 2017 will serve as depot for 17 new metro trains. The project was selected for “Outstanding Project of The Year” at the ITA Tunneling Awards 2015."

Jan 1, 2016

By Jacob Carr, Bruce Whisner, Adam Smith, Jingcheng Li

Electromagnetic-based proximity detection systems (PDSs) are utilized on mining machinery to protect workers from being pinned or struck. These systems generate magnetic fields covering the space around a machine, and a miner-wearable component (MWC) detects the field. The PDS determines the distance of miners relative to the machine based on the detected magnetic flux density in the magnetic field. This information is used to establish warning and shutdown zones around the machine. Maintaining a stable magnetic field is essential for system accuracy. However, components used to generate magnetic fields can be influenced by temperature changes. Depending on ventilation conditions and seasonal alternation, a PDS can be subject to significant temperature fluctuation. To better understand and quantify this phenomenon, researchers from the National Institute for Occupational Safety and Health (NIOSH) developed an experimental apparatus to study the influence of temperature on magnetic field generator circuits used in PDSs. Results from the study show that the electric current through a generator can be influenced by both ambient and internal temperatures, modifying the magnetic field that is produced. These findings show that temperature can significantly influence the ability of PDSs, used in underground coal mines, to accurately determine a worker’s position in relation to mining machine.

By Marianne Snedeker

In September 1985 we published a questionnaire asking about the content of MINING ENGINEERING and about your interests. By Dec. 10, our cutoff date, we had 430 responses, representing about 1.5% of the 28,238 people who received the September issue of ME. In the data that follow the tabulation and percentages are based on the number of individuals who responded to the particular question. About ME Through responses to the questionnaire, we were hoping to learn more about you, your interests, and how the magazine could better serve you. Those of you who responded told us something positive - you look at or read the magazine. Of the 430 respondents, 428 or 99.5% indicated that they had read or looked through the July and/or August issues. Those of you who refer to the magazine once are 207 or 48.5%. Those of you who refer to the magazine two or three times are 193 or 45.2%. Those of you who refer to the magazine four or more times are 27 or 6.3%. How much time do you spend reading the magazine? Of those responding to this question: 64 spent up to 1/2 hr 15.0% 224 spent up to 1 hr 52.6% 115 spent up to 1-2 hr 27.0% 23 spent more than 2 hr 5.4% In an informal survey among our staff, we determined that most people spend 1/2 to 1 hr reading magazines to which they subscribe at home. Does that match your experience? Many of you, 335 or 79%, clip your magazine for further reference. Also, many of you, 313 or 73.6%, do not pass your copy on to another reader, indicating that you are clipping it or receiving the magazine at home. Those magazines that are passed on reach: 1 person 3 0.7% 2 people 64 15.1% 3-5 people 34 8.0% 5 or more 11 2.6% Answers to what portions of the magazine you find useful indicated that the top three were Industry Newswatch, feature articles and Technical Papers; see Table 1. The "other" category included advertising - display, classified, Employment, and Professional Services - Washington Survey, New Products, Free Literature, book reviews, technology news, and Coming Events and Short Courses. We asked your appraisal of the technical level of the magazine. Of those responding, 39 or 9.1% indicated that it is too technical, 55 or 12.8% indicated it is not technical enough, and 335 or 78.1% judged it to have the correct technical level. In response to the question about whether you like to read an occasional feature that is not technically oriented, 21 or 5.1% said no, but an overwhelming 94.9% (393) said yes. Of the specific

Jan 1, 1986

By D. Shin

The gold leaching using cyanide from ore or waste has been almost universally in use [1]. Recently, biological gold bioleaching using cyanide producing bacteria, e.g. Chromobacterium violaceum, Pseudomonas fluorescens, or P. aeruginosa, has been investigated as environmental friendly and cost effective method. Among them, C. violaceum has been reported as effective cyanide producing bacterium on gold leaching [2, 3]. C. violaceum produces cyanide using glycine as a direct precursor and subsequently detoxify the cyanide by ß-cyanoalanine synthase [4]. However, until today only 0.026 ? 16.9 mg/L of cyanide production in YP medium has been reported in the literatures by C. violaceum [4-6]. Comparing with adding cyanide chemical, biogenic cyanide concentration is lower than the cyanide concentration added in traditional cyanidation. Since cyanide also forms complexes with a number of other elements such as iron, nickel, zinc, silver, copper, and platinum, it is very important for gold recovery to investigate the enhancement of biological cyanide production and set optimal experimental condition. Most of early studies on gold bioleaching by C. violaceum have been performed to investigate gold leaching mechanism using gold powder, and recently various resources such as ores, electronic scrap, and printed circuit boards of waste electronics [7]. Few studies have dealt with gold bioleaching from low-grade ore. In this research the feasibility of gold bioleaching by C. violaceum from low-grade ores containing gold was evaluated and fundamental study was performed for further scale-up study. The aim of this study was to improve the potential of gold bioleaching by C. violaceum from gold-containing ore; in particular, enhancement of biological cyanide production.

Jan 1, 2012