Search Documents

By J. S. Spivey

We in the coal industry, especially in the State of Illinois, put tremendous emphasis, including time, money and effort, into on-the-job training. The results of such training and safety have been tremendous. For example, in 1981 Illinois was the first major coal producing state in the history of coal mining to have zero mine-related fatalities. And in 1985, I am very proud to say, we had the second best record in the history of coal mining, with only two fatalities. Obviously, one fatality is one too many. Our goal is, has been and will continue to be to strive for excellence. It is sad, however, that in 1981 while were were celebrating zero fatalities in the workplace, there were 21 fatalities that occurred off the job. Thus, it has become a classic American story. Success with safety has been found in the workplace, but training and preparation to prevent accidents away from the job site have almost been ignored. Accidents are the leading causes of death in the United States for all persons age 1 thru 38, and are the fourth leading cause of death for people of all ages. Every single day, on the average, more than 290 Americans are killed in accidents - a rate of one every five minutes. The leading cause of fatal accidents in the U.S. is motor vehicles. And the number two cause is home accidents. A staggering statistic is that people are being killed off the job at a rate of about 9 to 1 over those on the job.

Jan 1, 1986

By Ed H. Wipf, Kurt L. Bryan, O&apos

Flow sheets employing SAG Mills as the initial stage of grinding are commonly selected for comminution of ores. Several alternative technologies are available. The paper will provide a brief review of the latest alternatives to SAG mills. Included in this review will be a discussion of the comparable benefits of each technology. Commonly accepted disadvantages will also be presented.

Jan 1, 1998

By Joseph W. Mussey

Bio-epigenetic sulphur deposits occur in Pecos, Reeves and Culberson Counties of far West Texas. Sulfate reducrng bacteria, utilizing hydrocarbons as energy, transformed gypsum into replacement limestone and hydrogen sulfide. Hydrogen sulfide, retained in the porosities of the replacement limestone, was subsequently oxidized by highly oxygenated groundwaters, and native sulphur precipitated. West Texas sulphur was first recognized at surface exposures by William P. Blake, a geologist attached to the Captain Pope Military/ Scientific Expedition of 1854. Attempts were made in the early 1900's to mine these sulphur vent exposures by a retort method, but the ventures met with little success. In 1967, Duval discovered a large sulphur deposit near some of the old sulphur works in Culberson County. Duval also extended a small sulphur deposit in Pecos County. The Frasch process, developed for producing sulphur from Gulf Coast salt domes, proved successful in West Texas type sulphur deposits also. However, modifications of the process were necessary to provide economical and efficient sulphur recovery from the varied ore modes. West Texas conditions and logistics require the ultimate in productivity to be competitive in the domestic and foreign sulphur markets. Several companies, in addition to Duval, are producing or have produced sulphur in West Texas. As of the first of June 1984, a total of 29.4 million long tons of sulphur had been produced west of the Pecos -aver. Duval produced more than 88 percent of that total.

Jan 1, 1984

By J. Stachurski

Flotation tests were carried out on 6 coal samples of different rank as well as their oxidized samples. A mixture of diesel oil and alcohols was used in these tests. Surface oxidation caused a distinct decrease of the flotation recovery with some improvement in the grade The reduction in the recovery increased with increasing the concentration of the oxidizing agent. The floatability of low rank coals was affected by oxidation to a higher degree than medium and high rank coals. The recovery size curves of oxidized samples mere similar in shape to that of non-oxidized coals.

Jan 1, 1990

By Nick Barton

The ability to estimate that support is unnecessary for various dimensions of opening in certain rock mass environments is of particular relevance in the mining industry, where most excavations are not expected to remain open indefinitely. As Hoek1 observes: "the basic aim of any underground excavation design should be to utilize the rock itself as the principal structural material, creating as little disturbance as possible during the excavation process and adding as little as possible in the way of concrete or steel support". Approximately two hundred case records have been analysed for the purpose of determining the amount of permanent support normally used when a given span is excavated in known rock mass conditions Some thirty cases concerned unsupported openings. Excavations that can stand unsupported appear to have certain common characteristics as regards rock mass quality. However, the mechanical properties of the rock mass are not the only factors controlling the choice of design. The dimension of the opening (span or height) and the type of excavation are two important variables.

Jan 1, 1975

By Steven Keim, Steven Stansfield, Kevin Andrews

Geotechnical, geological, and hydrogeological fieldwork and data collection for the mining industry is often conducted by younger, less-experienced staff members. In many cases, fieldwork personnel are recent college graduates or are otherwise relatively new to the mining industry. Due to busy schedules, staffing shortages, project budgets, and in some cases, poor management, new fieldwork hires often do not receive thorough training. In the past and the present, many workers in the mining industry learn(ed) by “doing.” While this is still considered to be the most practical approach and the easiest way for a company to determine the skill set of an employee, there is always some risk involved in the “feet to the fire” method. The reality is that field personnel are often collecting data on which major operational decisions will be made or on which regulators will base enforcement decisions. Inadequately trained or inexperienced field personnel may collect inaccurate data or fail to recognize key conditions that may influence decisions made by regulators, design engineers, mine managers, and corporate leaders. Even the best engineers may come to incorrect conclusions if they are starting with poor input data. Decisions based on inaccurate data often result in delays, budget issues, unsafe conditions, or even worse consequences. This paper provides numerous mining industry examples of incidences where inaccurately collected field information did, or could have, resulted in major adverse consequences. The paper also offers some simple approaches to minimizing the potential for such problems.

Jul 1, 2023

By Mingyang Li, Yan Lv, Xiaolong Ma, Xudong Gao, Jie Zhao, Yingyi Zhang

The reduction process of pre-oxidized ilmenite concentrate powder in 30%CO–70%N2 atmosphere was characterized by thermogravimetric and differential thermogravimetric (TG-DTG) analysis system at the temperature from 1073 to1223 K. The isothermal reduction results show that the reduction process is divided into three stages and the corresponding apparent activation energies are obtained by iso-conversional method and model-fitting method, respectively. For the first stage, the conversion degree increases sharply with increasing time, and the reduction process is controlled by the random nucleation and subsequent growth model (A2 model). For the second stage, the conversion degree increases slowly with increasing time, and the reduction process is controlled by the diffusion of carbon monoxide in the reduced layer (D1 model). For the third stage, the reduction processes at different temperatures are controlled by the diffusion of carbon monoxide in the reduced layer (1073 K and D1 model), phase boundary chemical reaction (1123 K and R2 model), random nucleation and subsequent growth (1173 to 1223 K, A2, and A3 models), respectively. For the whole reduction process, the apparent activation energies obtained by iso-conversional method and model-fitting method are 71.72 and 31.92 kJ mol−1 , respectively

By J. M. Mercier

Approximately seven (7) years of recent intensive mining activity in the Wasatch Plateau Coal Field of Utah has revealed distinct geologic patterns which, at times, profoundly influence reserve estimates, coal quality, mine layout, and reserve accessibility. Mine planning, economic feasibility, and resource recovery activities by Getty Coal Company utilize a multi-faceted approach by necessity when evaluating Utah properties. Two specific operating mines offer examples of the affects of adverse geologic conditions on mine operation and project economics.

Jan 1, 1984

By A. M. Whiting

Competition for coal producers and their primary customers has constantly increased during recent years. The effects of the Clean Air Act Amendments of 1990 on the electric utility industry, coupled with the normal complexities of coal production, quality control, transportation and contracting techniques have spurred both buyers and sellers to increase their level of sophistication. This paper will review the basic aspects of the U.S. coal business and explore the commercial approaches which have proven to be most successful.

Jan 1, 1994

By B. L. Bessinger

Because of a, work stoppage at the Carlsbad plant, IMC faced the challenge of operating a 24-hour-a-day mine and plant with inexperienced maintenance and production crews. This is an underground mining operation, using the room-and-pillar mining- method. The mine was entirely, mechanized with conventional equipment, was hoisting an average of 13,539 tons off ore per 24 hours, and employed a, mine maintenance group of 100 men. The 100-man, mine maintenance group was equally divided between mechanics and electricians. In re-forming this maintenance group, two main objectives were to be achieved (1) a general upgrading off the intelligence level; and (2) the elimination of craft lines for greater flexibility.

Jan 1, 1966

By Stig Premfors

Lamco Joint Venture is operating a Dravo Pelletizing machine to produce pellets from the natural slimes of an earthy hematite ore. The grate area of the machine 3.3 x 106 m equal to 350 m2 (3800 sq. ft.) and the installed fan capacity is 8200 HP. The limiting factor for production is normally fan capacity. This means that the processing fans can not pull the additional air (i.e the additional calories or BTUs) through the bed which would be required for increased production. A way to increase production without major modifications is to supply the additional calories needed for increase production by adding coal to the pellet feed. After successful laboratory tests following method of coal addition has been chosen and the following results have been obtained. 1. The ground coal is added to the slurry prior to the filters and the rotary dryer. 2. By adding 0.6% coal, an increase of about 15% in production rate has been obtained. 3. No significant changes of metallurgical properties have been observed (i.e. tumbler index, compressive strength, ferrous iron content, reducibility, Linder degradation and swelling). 4. No unexpected operation problems have been experienced. The pellet discharge temperature increases and is the limit for how much production can be increased by coal addition without making plant modifications.

Jan 1, 1971

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016

By Parris A. Lyew-Ayee

The Government or Jamaica has just completed agreements with four of the five bauxite/alumina companies operating in Jamaica. These companies are Kaiser, Reynolds, Alcoa, and Alcan, and the Agreements came into effect on February 1, 1980. One of the results of these new Agreements is the Acquisition of all company-owned bauxite lands by the Government and the rationalization of bauxite reserves.

Jan 1, 1980

By B. Zane Egan

The Calsinter process for recovery from fly ash involves sintering the fly ash with calcium sulfate and calcium carbonate at 1200°C, followed by a dilute sulfuric acid leach step. Flue gas desulfurization sludge containing calcium sulfite, calcium sulfate, and unreacted calcium carbonate may be substituted for the calcium sulfate and calcium carbonate. Conversion of aluminum in fly ash by the sintering process to an acid-leachable species was measured as a function of sintering time and temperature in the range of 800°-1200°C The sinter-leach steps were investigated using thermogravimetric analysis, x-ray diffraction, scanning electron microscopy, and elemental analysis. SEM photographs indicated that the glassy spheroids in the original fly ash were converted to a crystalline structure by the sintering reaction.

Jan 1, 1980

By Paul Soros

There has been a steady increase in shiploading capacities in the last 20 years. One of the reasons has been the general increase in ship sizes, with the largest vessels currently around 280,000 DWT in the bulk trades. Obviously, the large vessels can accept loads faster and their economic utilization justifies higher loading rates, up to a point. The high capacity facilities have loading rates far beyond this point. The economic logic of these facilities is based on the fact that for a given annual throughput the capital and operating cost of a single high capacity system is less than that of two smaller systems. Thus, where the projected throughputs are large, there is a great incentive to reduce capital costs by maximizing capacity. Tubarao, in Brazil, designed for a 100 million ton per year throughput with one finger pier and one high capacity berth is a successful demonstration of this approach. In the current state of the art, the high capacity systems have shiploading capacities in the range of 10,000 - 16,000 TPH, for annual throughputs of 20 million tons and larger per loading berth.

Jan 1, 1982

By Chen-Luh Lin, Jan D. Miller, Sindhoora Puvvada

Most of the future phosphate resources in Florida, which accounts for 70  percent of production in the United States, are contaminated with too much dolomite that is difficult to remove with existing industrial practices. The low-grade ore quality coupled with increased phosphate demand is of concern to the Florida phosphate industry. In order to resolve the dolomite issue, various beneficiation technologies were designed and evaluated, but none have been sufficiently successful [1]. 

By Godfred Amponsah, Mehrdad Razavi

Slope failures very commonly occur during a long period of heavy rainfall and groundwater rise. The failures pose a substantial risk to people, infrastructure, and equipment downslope. In the recent past, the mining industry has faced an increase in tailings dam failure due to several reasons including pore pressure increases in the dams. Many failures have been observed to occur during times of water level fluctuations but the critical factors that influence the initiation of slope failures still need to be adequately clarified. To investigate these factors, laboratory experiments were conducted on model sandy slopes to determine pore pressure-induced slope failure initiation. This study also presents a method to examine water seepage through soil slopes using an ultraviolet (UV) dye and a UV flashlight. The small-scale model test simulation demonstrated failures induced by either water percolation from the upslope tank at a constant level or by raising the water level at intervals. A bottom chamber fully filled with water to replicate groundwater rise was also simulated. The soil slope was monitored at every stage to study the deformations and behavior until failure occurred. Results gathered from the controlled laboratory conditions were useful for the verification of the numerical modeling method created in the computer program Slide. The analysis showed that slope failure always occurred when the toe was fully saturated. High pore pressures and seepage forces reduce the shear force at the toe to almost zero causing it to slide. A comparison of slope height to water level also indicated an average of 96% water level to cause a failure. At this point, the soil slope is fully saturated and has no matric suction. The findings in this study show that, by monitoring the moisture content of slopes, failures can be predicted.

Feb 1, 2024

By O. Tsuge, G. Hoffman

ITmk3®(Iron Technology Mark III) is an innovative new ironmaking technology whereby high quality iron nuggets are produced directly from iron ore fines and coal in a rotary hearthfurnace1). The reaction mechanism has been investigated in detail through fundamental laboratory research2)3), and the ITmk3 process has progressed from the laboratory to commercialization by the success of the pilot plant tests initiated at Midrex’ Technical Center and at the Kakogawa Bench Plant (KBP) located at Kobe Steel Ltd. Kakogawa Steel Works4)5). Pilot operations have demonstrated rapid production of the iron nuggets with complete metal/slag separation at a relatively low operating temperature. The Kakogawa Bench Plant (KBP) in Japan has logged 21 days continuous operation during which high quality iron nuggets were produced directly from fine ore and coal. The operation technology and the engineering data obtained from these pilot tests were instrumental for the scale-up of the ITmk3 process for the Mesabi Nugget Corp. pilot demonstration plant, which is located at Cleveland Cliffs Inc. Northshore Mining iron ore pellet plant in Silver Bay, MN. The ITmk3 process is an ideally suited technology for siting at the iron ore mine, as it allows the economical production of a value-added merchant iron product.

Jan 1, 2003

By M. A. Trevits, A. Ozment

"According to the Office of Surface Mining Reclamation and Enforcement Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires burning in 9 states. This is considered by experts to be an underestimate for the actual number of fires nationwide. Abandoned mine fires, if left uncontrolled can burn for years and in fact, one of the most well-known mine fires in the US, the mine fire in Centralia, PA, which began in 1962 has been burning for over 55 years. In Centralia, the mine fire won the battle, despite suppression and control efforts, as most of the residents were bought out by the State of Pennsylvania and moved away. However, the world record for the longest-burning coal fire, which may have been started around 6,000 years ago in New South Wales, Australia is still smoldering. Suppressing a coal mine fire requires cooling the hot zones and removing any source of oxygen. If the workings are shallow, the fire zones can be unearthed and the burning rock mass can be quenched on the surface. If the workings are too deep to excavate, then the fire must be fought remotely through boreholes using a variety of agents including water, gas-enhanced foam and grout. Access to surface areas for drilling can be problematic due to topographic and property constraints. When this occurs, large areas of burning may go unaddressed or simply left to burn. Fire Solutions, Inc. has been investigating the use of gas-enhanced foam in concert with directional drilling technology. Gas-enhanced foam has the advantage of using less water and adds inert nitrogen gas to displace oxygen to infiltrate and suppress a fire. Directional drilling has the capability to steer a borehole to a specific place underground. Directional drilling has many advantages over conventional drilling technology as it can provide the least disruption to the ground surface, minimize surface preparation and reclamation costs, multiple sites can be accessed underground from a single site and thus treated simultaneously and it offers increased efficiency because it is not constrained by difficult terrain. This paper discusses the combined use of these two technologies and it is hoped that with the use of these two technologies the efficiency and capability to address mine fires will be significantly improved. INTRODUCTION According to the Office of Surface Mining Reclamation and Enforcement, Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires in 9 states. This is considered to be an underestimate for the actual number of fires nationwide. Many mine fires are started by people burning trash where the coal seam or an abandoned coal mine is close to the surface. Other fire ignition sources include lightning and forest fires. Once ignited, a coal mine fire can easily spread into the remaining coal pillars and mine entries. Once established, the fire creates its own ventilation system supporting further combustion by drawing air down into the workings through unsealed mine shafts, fractures and surface subsidence depressions. As the coal left in the workings from the past mining operations burns, the mine void can collapse, causing subsidence and creating dangerous voids, damaging damage overlying surface structures and roadways. The products of combustion include smoke and noxious fumes such as carbon monoxide gas. These products are released to the atmosphere through fractures that develop within the ground surface, killing vegetation and creating serious health hazards [1]."

Jan 1, 2018

By T. J. Haddon

For the mining industry in general and gold mining in particular the past few years have been difficult. Economic conditions coupled with growing regulatory restrictions have led to increasingly important reasons for managing assets wisely. From a public company perspective this makes sense because it ultimately provides for an increase in shareholder wealth and that's what we're in business to do. Regardless of whether a company is public or not, assets must be managed effectively to remain a player in today's competitive environment. So, as the CEO of a gold mining company, how do we manage our assets to ensure that we are satisfying our obligations to our customer --the Amax: Gold shareholder? Let me tell you. As I said earlier, the gold industry has been under siege. We have just completed our third year of average prices below $400 per ounce. When you add finding and/ or acquisition costs and development costs to operating costs, there isn't much of a profit margin left. What this environment provides, however, is opportunities for growth. In the gold business, you either grow or you die. Today, most North American gold producers have at most a 10 year mine life. We are all scrambling to add reserves so we don't become extinct. As prices remain low, opportunities for increasing diminishing reserves abound. This is the time for the opportunistic company to take advantages of market conditions and that's precisely what we, at Amax: Gold, have done!

Jan 1, 1992