Search Documents

By Levent Ozdemir, Bjorn Nilsen

For several recent TBM tunnel projects, unexpected ground conditions have been encountered, causing extra cost, considerable delay, and in some cases major claims. Undoubtedly, insufficient and/or irrelevant site investigation and testing are among the main causes of such incidents. The purpose of this paper is to review the main investigations and tests relevant for hard rock TBM projects, with particular emphasis on the considerable development that has taken place over the last few years. Also, guidelines for defining optimum scope and extent of site investigations and testing are discussed, as well as the importance of adjusting the investigations and tests according to complexity of the ground conditions and project type.

Jan 1, 1999

By Jonathan K. Hrica, Brianna M. Eiter

The ability to identify hazards during a workplace examination is a critical skill for mineworkers to have in order to maintain a safe workplace. While research suggests that being able to successfully recognize hazards requires a complex set of competencies, it is unclear which competencies are most critical to adequately perform a workplace examination. This paper presents a hazard recognition competencies framework as an explanation of the competencies that affect mineworker hazard recognition. To better understand how the industry is selecting and preparing workplace examiners, researchers fromthe National Institute for Occupational Safety and Health (NIOSH) interviewed nine health and safety (H&S) professionals at surface stone, sand, and gravel mine sites throughout the USA. A primary purpose of these interviews was to verify the competencies included in the hazard recognition competencies framework and to understand why these competencies are critical. Finally, the results of this study are presented within the context of current NIOSH research findings related to hazard recognition.

Jul 27, 2020

By K. A. Larsen, J. L. Ariail, C. M. LaRosa

This article discusses the evolution of U.S. laws and policies towards environmental remediation at mine lands over the last 20years, the opportunities that these changes present for reuse, and the remaining challenges associated with community capacity for effective reuse planning and implementation. Emerging initiatives by the U.S. Environmental Protection Agency and Department of Interior for addressing these challenges are discussed.

Jan 1, 2004

By Norbert Patzelt, Johann Knecht

Future ore reserves of major gold producers in North America and elsewhere will consist of refractory gold ores. About 60 % of the current U.S. gold production is mined in Nevada. Several of the large gold operations in this state indicate that 40 to 90 % of their future ore feeds will contain refractory gold. To com­pound problems, average head grades for refractory U.S. gold ores had fallen from 8 - 9 g/mt to about 4 g/mt by 1991. In Latin America, 52 % of the gold operations will require milling for optimal recovery. Deeper reserves are, like in North America, refractory. Therefore a special treatment process is needed in order to allow for the gold ore to be leached downstream in a conven­tional cyanidation process for a high gold recovery. There are several options available for this oxidation process like treat­ment of the gold bearing ore in pressure oxidation, in a biooxi­dation or in a roasting plant depending on the reason for the refractoriness. If organic carbonaceous matters and sulfides are the prima­ry reasons for the refractoriness, whole ore roasting is a pre­ferred method for the treatment of this type of ore. Since dry ore is to feed to the roaster, a dry grinding mill is advantageous. For the dry grinding system, the moisture content and the ore char­acteristic is of importance. Those parameters decide the mode of the grinding system. For autoclave systems common wet grind­ing systems can be applied. This paper deals with technical aspects for dry grinding plants and gives an outlook on and pos­sibilities for new grinding systems.

Jan 1, 1996

By M. N. Semenoff

On July 8, 1999, EPA announced the RCRA Cleanup Reforms, a set of administrative reforms designed to achieve faster, more efficient cleanups. This paper will discuss the Reforms, the status of their implementation and assess these potential impacts on the mining industry.

Jan 1, 2001

By Massimo Concilia, Remo Grandori, Paolo Nardone

Paul Y. – SELI Joint Venture had been contracted to build the longest section of the Strategic Sewage Disposal Scheme (SSDS) – Stage I. This involved two tunnels under urban and marine areas excavated by high performance hard rock open type TBMs operated from deep shafts. A specific ground treatment program was developed using advance probing and grouting to control water inflow into the excavations. The article describes: the technologies adopted, the experienced problems, the encountered productions and their interrelation with the water inflow amounts, the possible improvement in the technologies for the excavation of the future stages of the same project as well of any other project under similar conditions.

Jan 1, 2001

By K. Kovári, G. Anagnostou

Slurry and EPB-shield tunnelling have been successfully applied worldwide in recent years. Under extremely unfavourable geological conditions, however, face instabilities may occur. The present paper aims at a better understanding of the mechanics of face failure. For the case of slurry shield, attention will be paid to the time-dependent effects associated with the infiltration of slurry into the ground ahead of the face. Related topics, such as the stand-up time and the effect of the excavation advance rate, will be discussed. In the case of an EPB-shield, a distinction will be drawn between fluid-pressure and effective pressure in the chamber. The effective pressure can be visualized as a “grain to grain” contact pressure between the muck and the ground at the face. The water pressure in the chamber reduces the hydraulic head gradient in the ground and, consequently, the seepage forces acting in front of the face. The face is thus stabilized both by the direct support of the pressurized muck and by the reduction of the seepage forces in the ground. The paper includes normalized diagrams which allow the assessment of tunnel face stability.

Jan 1, 1997

By Steven G. Vick

Effects of the August 1995 failure of the Omai tailings dam in Guyana continue to be felt throughout the mining industry. This article is taken from the final report of the independent body of experts commissioned by the government of Guyana to establish the cause of the failure. It explains what happened, why and how to avoid it in the future. Despite environmental, health and safety effects that were negligible by any objective measure, the failure has received wide international attention. Coming on the heels of the shift in exploration targets and development opportunities to developing countries, it has intensified interest in tailings dam safety and environmental management issues. An informed understanding of the nature of the failure and its effects is key to responding to these concerns.

Jan 1, 1996

By S. Chander, S. W. Musselman

The molecular structure of hydrophobic and hydrophilic groups in nonionic surfactants has been related to the wetting and dispersion of selected pigments. The nonionic surfactants included in this study are acetylenic diol based surfactants and ethoxylated alkyl phenols. The Langmuir model could be used to fit adsorption data. Further analysis of the data showed that the free energy of adsorption was a function of adsorption density of the surfactants at the interface. The change in free energy with adsorption density could be interpreted by considering a change in the orientation of the adsorbed molecules. Acetylenic diol based surfatants were found to have an area per molecule of 2-3 times that of similarly ethoxylated alkyl phenols. The wetting and dispersion properties of lamp black, a model hydrophobic surface, by these surfactants were investigated by contact angle measurements and particle size analysis. Acetylenic diol based surfactants with ethylene oxide contents between3.5 and 10 moles per molecule and alkyl phenol based surfactants with approximately 9 moles of ethylene oxide per molecule were found to provide superior wetting abilities. Longer ethylene oxide chains were required for superior dispersion capabilities within each family of surfactants. Complete wetting and dispersion was found to occur above the critical micelle concentration of the surfactants.

Jan 1, 2000

By I. R. Firth, D. L. Taylor

The ability to accurately model the movement of grade boundaries during a typical bench blast would be of significant benefit to mine operators. The movement of grade boundaries during the blasting process may have significant impact on grade recovery if not accounted for. The paper describes the preliminary stages of a research project which combines numerical blast models and conventional mine planning software to allow practical use of the results of a numerical blast simulation. A two dimensional bench blast is simulated using the Universal Distinct Element Code (UDEC). The results of the simulation are used to provide input to the Surpac mine planning package which can be used to generate grade control plans.

Jan 1, 2001

Well designed and maintained haul roads are the key to minimizing truck haulage on-road hazards and costs, as well as increasing productivity. However, practically designing and managing a haul road for optimal performance is often difficult to achieve. Poorly designed and built roads exhibit high rolling resistance - a 1% increase in road rolling resistance can typically reduce speed on ramp by as much as 10% - and on the flat by up to 26%. In the current economic climate, investment and operating decisions come under scrutiny. In the long run, this scrutiny returns improved efficiencies and leaner, healthier operations. The focus of this evolving evaluation process should and will certainly fall on haulage operations ? simply by virtue of their contribution to overall cost of operations ? often in excess of 50% of total costs for deep open-pit mines. Whilst the end result - improved efficiency and reduced cost per ton hauled ? is not in itself problematic, it is the route, or process followed to achieve these savings that needs to be carefully managed. We can be guided on this journey by our understanding of how a road design is developed, and, critically, the interplay between a good design and safe, cost efficient haulage. This paper briefly summarizes the evolution of mine haul road design, from the seminal USBM work of Kaufman and Ault in 1977, through to current geometric, structural, functional and maintenance management design components. These augmented design and management guidelines have been developed over the past decade, both in response to the requirements of mine operators for more safe and efficient haulage systems, and the truck manufacturers? requirements for a more predictable and controlled operating environment. These developments have been paralleled by the need to minimize haulage hazards, both from a health and safety perspective. Whilst improved mine haul road design does indeed reduce haulage accidents, recognition also needs to be given to human factors which are a significant contributor to haulage accidents. The human factor is the most problematic to address in a road design. It is often easier break the link between the interactive effects which may lead to accidents than trying to predict and reduce human error. These human factor interactive effects include the geometric, structural and functional design components and to prevent an accident or reduce the severity of its consequences, a road should be more accommodating to human error. The more that is known about human error, the better a road can be designed to accommodate those actions or non-standard practices that would, on a poorly designed road, invariably escalate an error into an accident.

Jan 1, 2010

By G. France

The Blair Athol Coal Mine (BAC) is a large open cut operation in the Bowen Basin of Queensland, Australia. Current mine capacity is about 11 million tonnes per annum(Mtpa) of export coal. On-line analysis at BAC consists of two Coalscan 9500s installed directly on the output of the crusher plant and immediately before the product stockpiles, while a third Coalscan 9500 is installed on the transfer conveyor feeding the train loading bin. The two product Coalscans have a dual purpose. The first is to provide real time coal quality data directly back to the mining operations. The second is that of modeling the product stockpile with accurate on-line information. This modeling enables both production and coal quality personnel to accurately examine the coal quality of each stockpile with a degree of resolution which previously had never been achieved.

Jan 1, 1999

Current design guidelines for the surface catalysed oxidation of Fe(II) on Fe(OH)3 (Ochre) in passive mine water treatment systems are based largely on empirical data as the details of rates and mechanisms have not fully been revealed. Also the effects of elevated carbonate concentrations, typical of many UK minewaters, on the surface catalysed oxidation rate are unclear. In order to move away from empirical design and towards sound engineering that is based on geochemical and hydrological understanding it is necessary to quantify these reaction rates. In this study the effects of Fe(OH)3 and carbonate on the rate of Fe(II) oxidation by dissolved oxygen have been investigated with an aim to delineate the reaction mechanism. Experiments were conducted under well-controlled conditions. Preliminary results indicate that the surface catalysed reaction is an order of magnitude faster at pH ~6.4 with 200 mg/l Fe(OH)3 than the homogeneous rate and is dominated by an elevated rate of removal and oxidation of Fe(II) from the solution phase. It is also apparent that the oxidation rate of actual adsorbed Fe(II) is substantially retarded with respect to the homogeneous rate. Carbonates were not shown to affect the surface rate within the bounds of this preliminary study.

Jan 1, 2006

By Turker Hudaverdi, Yasar Agan

This study tries to predict blast-induced flyrock using intelligent modelling techniques. Flyrock is a site-specific phenomenon. Design variables and rock properties highly influence flyrock throw distance. Site investigations were conducted in a sandstone quarry. Fundamental operational parameters, blast dimensions, bench face condition, and rock mass structure were monitored. Stepwise regression technique was applied for variable selection. Burden–hole diameter ratio, in situ block size, and powder factor were determined as the most significant parameters. Considering output of stepwise regression, artificial neural network, ANFIS, and Gaussian process regression techniques were applied to predict flyrock throw. A comprehensive validation was performed using twelve different performance indices. Pre-determination of input parameters supported development of successful soft computing applications. Rock block size was found to be an appropriate input variable for flyrock modelling. In addition to classical performance indices, standardized and symmetric accuracy metrics were quite useful in model validation process. The intelligent models predict flyrock range with an error less than 6 m. The mean percentage errors are lower than 10%. ANFIS seems to be the best model for flyrock prediction. The calculated mean absolute error is 5.36 for ANFIS model.

Nov 12, 2023

The 22nd Annual American Mining Hall of Fame Awards Banquet sponsored by the Mining Foundation of the Southwest will be held at the Westin La Paloma in Tucson, AZ on Saturday, Dec. 4, 2004. This year’s inductee, guest of honor and featured speaker at the banquet will be J. Steven Whisler, chairman and chief executive officer of Phelps Dodge. Whisler is also a director of Phelps Dodge, Burlington Northern Santa Fe, America West Holdings, the National Mining Association, the International Copper Association and the Copper Development Association.

Jan 1, 2004

By Ronald M. Hays

The White Pine Copper Division of Copper Range Company is a large copper producer operating an underground mine, mill, and smelter on Michigan's Upper Peninsula. Principal water discharges are from the tailings basin where these discharges are high in dissolved solids because of mine water pumped into the basin. Principal air emissions are from the smelter where SO2 emissions are uncontrolled. Although water discharges and air emissions have not had significant environmental impacts, environmental regulations could require additional control procedures. Because of low copper prices and poor profitability, cost of compliance with possible new environmental regulations could have serious impact on White Pine with no apparent significant beneficial environmental impacts.

Jan 1, 1979

By William H. Langer

I spent 41 years as a geologist with the US Geological Survey (USGS) conducting geologic studies and preparing peer reviewed maps and reports describing the results of those studies. Since retiring from the USGS in 2011, I have been a consultant specializing in aggregates and other industrial minerals. Consequently, I have had the opportunity and pleasure to apply the information contained in those kinds of geologic maps and reports to real-life situations. About half of my consulting is performing due diligence for mineral resource evaluations of one type or another where resource information has been provided by the property owner. Many of those jobs necessitate that I conduct desktop studies followed by field work. I then use my information to review and comment on the written reports of others; reports variably referred to as geologic reports, resource studies, reserve analyses, and so forth. While there are many well written reports addressing geologic resource issues, I was surprised to see that there are also a significant number of so-called geologic reports that only pay cursory attention to geology. Unfortunately, that lack of rigorous geologic investigation commonly leads to erroneous conclusions. This paper addresses three such reports covering concrete sand, metallurgical gravel, and proppants (frac sand). Although all three examples are located in the Gulf Coastal Plain Province, I do not reveal the exact location of any of the properties for purposes of confidentiality. Furthermore, I have generalized the site descriptions and illustrations. However, all the descriptions faithfully define the geologic situation.

Feb 1, 2024

By R. L. Grayson, R. C. Althouse, L. A. Layne, M. J. Klishis

Introduction The researchers combine a detailed microanalysis of accident data and roof bolting field observations to develop new and meaningful risk indices for the roof bolter job classification. These indices incorporate information that has not been used in traditional measures of risk. The significant parameters that these new indices incorporate are the total number of accidents occurring within a particular work activity, the amount of time a miner usually spends performing the work activities in which the accidents occurred, and the average severity of the injuries incurred in the accidents. Being specific for a particular job, they aid comparisons among work tasks performed in the bolting cycle. The indices' specificity provide anew basis for reexamination of training and operational development of miners for specific jobs. Microanalysis The roof bolting microanalysis was performed by examining the empirical data and written summaries for all bolting accidents reported in the West Virginia Safety Information System (WVSIS) for the years 1983-1987. The WVSIS database contained more than 15,000 accident narratives. The microanalysis of bolting accidents covered 2083 reported personal injuries (RPIs). This large number of injuries, performed at an industry-wide level, provides a broad picture of the nature of roof bolting injuries. The analysis focuses on the activities associated with the cyclical routines of the roof bolting process. For this analysis, roof bolting tasks were categorized into work routines based on the sequence of work activities performed by roof bolters. Four work routines were identified within the overall bolting cycle. And these routines comprised 70% (1217) of all roof bolting accidents at the face. The routines include: face area preparation; tramming, positioning and setting the automated temporary roof support (ATRS); drilling holes; and installing bolts. The types of injuries most common within a routine and the average severity of those RPIs were also identified. Table 1 gives a breakdown of the percentage of accidents by the bolting routines. Another 19% of the roof bolting RPIs cannot be classified in a particular routine because of the vagueness of the narratives. However, it was clear that these accidents involved drilling holes or installing bolts. These results are consistent with previous research. It identified drilling and bolting, followed by tramming, as the most frequent sources of injuries (Helander, Krohn & Curtain, 1983). [Table 1-Accidents by bolting routines at the face Accidents Bolting routine Percent Number Face area preparation 18.2 222 Tram, position, ATRS 23.3 284 Drilling holes 34.2 416 Installing bolts 24.2 295 Total 1217] Roof bolter operators were involved in 82% (1706) of the 2083 accidents. The RPIs incurred by classified roof bolters occurred largely on working sections (95%) and at the face area on the working section (75%). Approximately 23% of the 1706 roof bolter RPIs occurred during tasks which were not part of the bolting cycle. These included belt utility work, providing supplies and section moves. Miners in other job classifications who were involved in roof bolting accidents accounted for the remaining 18% of the 2083 roof bolting RPIs. Among this group were section utility men and general laborers (41%), section machine operators (38%), and electricians and mechanics (11%). Another 9% were performing on-section supervisory functions. Face area preparation Face area preparation work led to a substantial number of injuries, although it accounted for the lowest number of injuries of the four routines. Several tasks were associated with the injuries incurred in this routine. Table 2 shows the percentage of injuries associated with face area preparation. [Table 2- Accidents occurring during face area preparation 26.6% Setting temporary and supplemental supports 24.8% Scaling roof and ribs 21.2% Installing ventilation devices 15.8% Handling supplies and materials 11.6% Miscellaneous tasks] The injuries commonly involved overexertion and 'struck by' falling coal and rock. Handling materials often led to overexertion injuries. Nearly 66% of the scaling-related injuries and about 33% of the injuries incurred during the setting of temporary supports involved 'strikes' by equipment, materials, top and rib. Tramming, positioning and setting the ATRS During tramming operations, workers were often struck by components of the machine and hit by loose roof and rib. Poor footing also led to slips, sometimes against the moving machinery. Table 3 gives a breakdown of accidents in this routine. Control levers were a significant problem in this routine.

Jan 1, 1993

By M. Deul

For the first half of the 21st Century the USA will rely on the same mix of fuels as for the past 50 years: Petroleum will cost more and availability will decline as developing nations modernize. Increased use of natural gas for electric power generation will result in severe stress on gas supply. Coal will be the fuel of last resort. More than half the petroleum used is imported, about the same amount as used for transportation. Only coal can provide relief by fueling railroads through electrification while encouraging ‘piggy-back’ trailer haulage, co-generation for manufacturing and expanded passenger service.

Jan 1, 2002

By Rosa Malena Fernandes Lima, Kerollan da Silva Ramos, Joyce de Assis Silva, Geriane Macedo Rocha

This study evaluated the effects of collector type amide-amine compared with those of conventional etheramine acetate (both cationic collectors) on the surface properties of quartz and hematite. An examination of certain properties of the reagents indicated that the new collector amide-amine has CMC (critical micelle concentration) and pKa values (100 mg/L and 8.2, respectively) significantly lower than those of etheramine (800 mg/L and 9.4, respectively). Microflotation tests showed that the recoveries of quartz with amide-amine in all the concentrations tested were higher than those with etheramine. This is attributed to its lower CMC and pKa values. The selectivity window between quartz and hematite flotation using amideamine was higher at pH 10.5 (approximately 80% for 5 mg/L). Therefore, the use of starch is not necessary in siliceous itabirite flotation by amide–amine collector. Zeta potential measurements and infrared spectra reveal that the adsorption of amide-amine collector on quartz surface occurs mainly by electrostatic attraction. Considering the better collectability of amide-amine for quartz flotation and lower adsorption affinity for hematite surface than etheramine, the amide-amine is a promising collector to be used in reversal iron ore flotation.

Jul 30, 2021