Search Documents

By M. D. G. Salamon

If a transition from one equilibrium state to another occurs during the course of mining, energy transfer takes place in the rock mass, which is assumed to be an elastic continuum. The energy components are defined as follows: the work done by external and body forces, W; the increase in stored energy in the mass, Uc; the strain energy in the rock mined during the transition, Urn; the work done on mine support or backfill, Ws; and the released energy, Wr. The energy balance is defined as (W + Urn) - (Uc + Ws) = Wr> 0, where the first set of components in parentheses represents the sources of energy, while that of the second corresponds to the known modes of energy expenditure and the component on the right is the unaccounted-for energy surplus, which must be released and dissipated in some form. The inequality Wr ~ Urn> 0 applies. Expressions for the energy components are derived first for the general case and then for the 'slit' modal used to simulate tabular excavations. Through specific examples, the importance of the progressive nature of mining is emphasized. The size of the steps used to enlarge the excavations appears to play a significant role in the mode of energy transfer. This observation forms the basis of the second paper in this series of two papers.

Jan 1, 1984

By G. A. Matthrsuis, R. N. Morris

The paper identifies two zones in a Leeds flotation cell. The ratio (13)of the dissipative forces and the interfacial tension force acting on a bubble and a solid particle are shown mathematically to be proportional to the square of the particle diameter for the quiescent zone and inversely proportional to the particle diameter for the turbulent zone. To locate the range of operation, correlations were established for the bubble diameter through photography and bubble counts. 13was found to be fairly constant in the particle size range 38 to 150 ",m, and the level of turbulence unlikely to affect the bubble-particle attachment and hence the beneficiation efficiency. This was verified in a series of flotation runs with a standard Leeds cell and a modified cell of twice the height to increase the capacity of the quiescent zone. A series of tests on the size range 300 to 600 ",m showed that the turbulence level had a marked effect on the cell performance through a relative improvement in the beneficiation efficiency due to the increased height of the cell. To identify the significant variables in the size range 38 to 150 ",m, a factorial design was carried out. Promoter dosage and particle size were found to be significant, aeration rate and impeler speed being insignificant at the 95 per cent confidence level. Multiple regression correlations were established for the recovery of organic material, mineral rejection, and beneficiation efficiency.

Jan 1, 1988

By H. Wagner

It is a great privilege for me to have been asked to present the closing address to this most successful symposium on backfill in the South African mining industry. When I accepted this invitation I did not fully appreciate the tremendous progress made on most aspects of backfilling in the last few years. The number and quality of papers presented at this symposium bear testimony to the mining industry's determination and success in introducing backfill in underground mines to improve strata control and environmental conditions, and to provide better protection to mineworkers against the hazards of rockbursts and rockfalls. Many contributions demonstrated that these benefits can be achieved at a reasonable cost, and in some instances improved grade and higher rate of face advance result in improved economics. In my closing address I will attempt to summarize the progress made in the various aspects of backfilling underground workings and to identify those areas which, in my opinion, require further attention and effort. I will undertake this review under the following main headings: ? fundamentals of backfilling; ? design of backfill systems; ? operation of backfill systems; ? control of backfill systems; and other aspects of backfill systems.

Jan 1, 1988

By Phil Morriss

During the last 12 months, Sandvik?s Technical Service Group has carried out nine Scoping and Pre-feasibility studies for the application of In-pit crushing and conveying (IPCC) for large mining companies; the majority in conjunction with the Snowden Consulting Group. During these studies several key and recurring drivers have been identified: 1. Mining schedule issues ? there are several issues which crop up repeatedly, including: ?the unnecessary curvature of pit walls, ?very high rates of vertical advance which are (created by schedule optimisers to minimise stripping at all times) which are at the limit of what can be realistically achieved (and which of course make it harder for IPCC to achieve any impact), and ?The allocation of material to semi-mobile systems to maximise the ability for IPCC to be an effective alternative. 2. IPCC productivity issues ? the key issues are the IPCC system operating hours achievable, and the system throughput (both instantaneous and the average). 3. IPCC Risk issues ? there are perceptions about the risks associated with the use of IPCC which are a mix of reality and fiction, but which nonetheless create negativity towards the use of IPCC. In this paper, the authors wish to address specifically the factors affecting the IPCC productivity.

Jan 1, 2008

By R. G. B. Pickering

The Faculty of Engineering at the University of the Witwatersrand and the Mining Technology Division of the CSIR have co-operated to define the problems associated with deep level mining and in this paper they will identify what they consider to be the critical areas requiring technological solutions. This perspective will then be applied to work currently being carried out by both the organizations and gaps for additional developments will be identified. Finally the Co-operative Research Centre methodology operating in Australia is described. The purpose of this CRC is to provide a vehicle for R&D co-operation to develop and implement technologies which will increase the competitiveness of the mining industry. A further objective is to develop an appropriately skilled human resource base.

Jan 1, 1996

By H. D. Mtegha

Mining is important to the economies of both Tanzania and Namibia. Recently, both nations revised their national mineral policies to ensure future economic benefit. The main difference in the mineral policy-formulation processes followed by the two countries is identified as the degree and timing of stakeholder involvement during the articulation process. In the case of Namibia, the stakeholders were involved from the start in identifying issues and in suggesting policy solutions. In contrast, the Tanzanian process involved stakeholders after a framework had been developed by a task team. The Tanzanian emphasis was on attracting foreign investment into a traditionally state enterprise system of mineral investment and development. One can argue that the policies developed met the initial requirements, and both are, therefore successful, despite the different processes of policy formulation that were used. However, several fundamental questions arise as a result of the two approaches. This paper attempts to answer these questions by providing a comparison of the processes used for developing and formulating the mineral policies of Tanzania and Namibia. It concludes that the Namibian consultative process is perhaps more sustainable in the long-term because of its wider public support. Time will tell which of these policy-formulation processes provides a basis for sustainable economic growth for developing mineral economies.

Jan 1, 2010

By M. Helm

Over the last 40 years, numerous investigations have focussed on the preg-robbing capacity of carbonaceous material during gold ore processing. Various techniques have been applied to characterize the physical and chemical properties of the carbonaceous material in efforts to predict its preg-robbing capacity. The present study, which forms part of an ongoing investigation, is specifically designed to increase the understanding of preg-robbing in ores containing carbonaceous material. In excess of 100 samples from 13 gold mines located in major gold provinces of the world have been incorporated into the present study. These samples were characterized using industry standard metallurgical techniques and were shown to have gold adsorption capacities ranging from a few grams to many hundreds of grams of gold per ton of ore. Further analysis showed that the crystalline nature of the carbonaceous material, which is related to its geological history, is important in determining the preg-robbing capacity of an ore. This finding builds on the common understanding that the preg-robbing behaviour of an ore is related to the amount (or abundance) of carbonaceous material present in that ore. In this study, Raman spectroscopy was used to evaluate the physical nature of carbonaceous material. This is a tool which has been successfully applied by researchers for the characterisation of carbon materials, with respect to crystallite size and lattice defects. Raman analysis of the samples included in this study showed varying degrees of disorder in the carbonaceous materials from the different deposits. Comparison of the Raman spectra with the gold loading capacities of the samples indicated a direct relationship between the structure of the carbonaceous material and its capacity to preg-rob gold. From this, a simple and robust method has been developed based on the Raman spectra of the sample and carbonaceous material content to predict the preg-robbing capacity of an ore. The potential exists to develop a predictive tool using Raman spectroscopy for characterising the preg-robbing capacity of an ore. Such a tool would have potential application in projects ranging from the early stage of exploration through to more detailed feasibility studies and mining operations. The result of applying the predictive method outlined in this paper would be the effective and proactive management of the deleterious influence of carbonaceous material on gold recovery in mining operations.

Jan 1, 2009

By Jean Michel Marino, Jean-Pierre Slama

"The computer methods used by the French Commissariat a l'Energie Atomique, which are applicable to any type of ore deposits, are:(i) Ore reserve estimation. The data are either the core analyses or gamma leggings. To determine the spatial distribution of the ore, three different methods of interpolation are used. Two of these are based on the least-squares theory and the third one is an application of the regionalized variable theory. The interpretations of the orebody by the geologists are introduced in the computer program as often as possible.(ii) Optimal open pit design. From the spatial distribution of ore, the three-dimensional outlines of the optimal pit are determined by a geometrical algorithm which allows different slopes varying with the azimuth.Finally, the optimization of annual successive plans arc discussed."

Jan 1, 2014

In the wake of the financial crisis that affected world markets in 2002, there has been an increasing international focus on corporate governance. Various corporate governance codes of practice have been introduced, such as the Sarbanes-Oxley legislation in the USA, the Combined Code in the UK, and King III in South Africa. This focus on corporate governance has increased since the most recent financial crisis in 2008, the effects of which are still being felt world-wide. In the mining and minerals industry, reliable metal accounting is essential to sound corporate governance and is also becoming a focus of increased attention and concern, particularly as the figures generated by the metal accounting system feed directly into the financial accounts of mining companies. Mass measurement, sampling, and analysis provide the input data for the metal accounting system and sound corporate governance requires that the procedures used are based on best practice and that the data generated is accurate and handled correctly, transparently, and consistently to produce the accounting reports. The AMIRA Code of Practice for Metal Accounting has been widely adopted in the industry as a means to achieve this, and the compilers of the Code have conducted numerous metal accounting audits at operations, both in South Africa and abroad. These audits have shown that there is a real need for such a code of practice. Keywords metal accounting, AMIRA Code, corporate governance, risk management.

Jan 1, 2014

By C. Ringas

Pipelines are used extensively in industry to convey various products. Internal corrosion of pipelines can lead to perforation and leakage of the product. A growing problem, not often accurately recognized, is internal corrosion of pipelines caused by bacteria. Microbiologically-induced corrosion (MIC) refers to corrosion caused by a variety of micro-organisms. This form of corrosion is not widely recognized in many industries, although it is widespread and causes many corrosion problems in pipelines, both internal and external. Sulphate-reducing bacteria (SRB) are responsible for the bulk of the corrosion problems caused by MIC. Corrosion caused by SRB is found extensively in water pipelines conveying raw, potable and waste water, as well as in pipelines conveying slurries. This problem also occurs in pipelines conveying crude oil. This paper describes internal corrosion problems of slurry pipelines caused by bacteria and outlines mitigation methods to improve slurry pipeline integrity, thereby extending the life of such pipelines.

Jan 1, 2007

By S. Potgieter-Vermaak

The main mineral components of the so-called heavy sands (or black sand) are the titanium, zirconium and iron-bearing minerals, rutile, zircon and illmenite, accompanied by various minor and trace amounts of silicates or phosphates, often present together with the rare earth elements. The investigated samples originated from Richards Bay Minerals (RBM) in South Africa, which is jointly owned by BHP Billiton and Rio Tinto, the largest titanium slag producer in the world. The present study focused on the characteristics of samples originating from various points in the separation plant. The heavy-mineral fractions and concentrates of a representative suite of samples were investigated using various analytical techniques to establish the differences in morphological and elemental compositions at the different points in the plant. These techniques included: reflected light microscopy, micro-raman spectrometry (MRS), scanning electron microscopy coupled with energy dispersive X-ray analysis (SEM/EDX) and structural and chemical analyser (SCA). All samples comprised a heterogeneous population of zircon and rutile grains with diverse physico-chemical properties, expressed by large differences in colour and trace element chemistry of single grains. The elemental composition proved the presence of the rare earth elements that appeared to coexist with both Ti and Zr minerals. The percentage of grains hosting inclusions, such as anatase, monazite, quartz, spessartine, augite, epidote and actinolite, varied for each sample and could be uniquely characterized by Raman investigations. Keywords: heavy mineral sands, micro-ram an spectrometry, elemental analysis

By E. J. Magri

This paper describes a geostatistical study of the relative merits of diamond-saw sampling and conventional chip sampling, using results from experimental work carried out on Randfontein Estates Gold Mine and Western Areas Gold Mine. The diamond-saw sampling procedure is described, and it is concluded that this is a very efficient operation and leads to good-quality sampling that is clearly an improvement over conventional chip sampling. The study principally involved the computation of the errors of estimation of the mea gold value of mining panels for the two sampling methods, revealing that, in the normal production environment, the diamond-saw sampling method is a significant improvement over conventional chip sampling, as evidenced by the reduced estimation errors achieved. The question of optimum sample spacing is discussed, and it is concluded that the required spacing for chip sampling needs to be smaller than for the diamond-saw method.

Jan 1, 1986

By C. M. Suhr

n order to validate the borehole analysis valuation procedure commonly used in the South African gold mining industry, a simulated orebody was used to create borehole values which would serve as data for the procedure. After confirming the distribution, calculating the variance size of area relationship, estimating the block variance, and calculating a profit measurement for each set, comparisons were made to the known population parameters. Results show only one overall bias (in the estimation of the lognormal third parameter), which is carried throughout the analysis. The remainder of the analysis is unbiased, validating the procedure.

Jan 1, 1987

Material transfer in underground mines often relies on ore and waste pass systems. Over the years the authors have investigated the design and performance of orepass systems in several Canadian and South African mines. It has been recognized that while most mining operations have either implicitly or explicitly clearly defined objectives, in the design and successfully operate orepass systems there seems to be an absence of a strategy on how to best attain these goals. Consequently, it is not surprising that the majority of operations reviewed by the authors experience a number of problems of varying degrees of severity and economic consequences. This is illustrated by reference to both South African and Canadian operations. The second part of this paper focuses on a review of tactical interventions to rectify orepass problems or mitigate their impact. The paper closes with a framework for a flexible strategy for the design and operation of orepass systems. Keywords orepass; orepass design; orepass stability; orepass rehabilitation; orepass operation; orepass strategy.

Oct 1, 2013

By M. Gericke

Over the past few decades the commercial application of heap bioleaching technology for the extraction of base metals has become increasingly important, due mainly to the depletion of high-grade ore reserves. Heap bioleaching is widely used for the extraction of copper from secondary copper sulphide ores. The design and engineering aspects of the process have received considerable attention, but issues related to the microbiology of the process have been subjected to less rigorous scrutiny. The major role of micro-organisms in bioleaching processes is to catalyse the regeneration of ferric iron and protons, from ferrous iron and by sulphur oxidation respectively. It is accepted that even the most carefully engineered heaps are heterogeneous in terms of temperature, pH, the presence of anaerobic pockets, irrigation efficiency, and dissolved solutes. Since interactions between solution chemistry, mineralogy, and microbial populations exist in heaps, a better understanding of the correlation between microbial numbers and types with changes in these chemical and physical profiles with time would be beneficial during process design and operation of heaps, and could result in faster start-up times and higher metal recoveries. This paper reviews the role of microbiology in heap bioleaching processes. Aspects such as microbial diversity, identification and monitoring of cultures, inoculation strategies, colonization behaviour, and tolerance to metals and salts are discussed, and the potential contribution of the knowledge to the improvement of the operation and design of heap bioleach processes assessed. Conclusions are drawn with respect to the role of genetic engineering, heap inoculation practises, and remaining areas for future heap bioleaching research and development.

Jan 1, 2012

By K. Sinding

This paper discusses reasons for mining company mergers that have become the fashion, the role of the ?Juniors? and asks what the motives might really be. It examines changes in company concentration over the last 20 years in key mineral segments. Data at different stages of a project are examined to attempt to elucidate the role of the ?Juniors?. Areas for further research are suggested.

Jan 1, 2009

By J. Dvorácek

Mine water poses a significant problem in lignite coal mining. The drainage of mine water is the fundamental prerequisite of mining operations. Under the legislation of the Czech Republic, mine water that discharges into surface watercourse is subject to the permission of the state administration body in the water management sector. The permission also stipulates the limits for mine water pollution. Therefore, mine water has to be purified prior to discharge. Although all mining companies operate mine water treatment plants, there is hardly any utilization of the final effluent. The high expenditure involved in the more sophisticated methods of mine water treatment has fuelled the search for the commercial utilization of the effluent.

Jan 1, 2012

By P. A. Corbeil, C. Swart, F. Miller, V. Falmagne

Automation technologies are increasingly adopted in different mines worldwide. This paper presents the technical aspects of vehicle automation applications at two Noranda operating mines. Teleoperation of 5 LHD’s at Noranda’s Bell Allard mine is used in order to meet aggressive mining requirements under difficult conditions. The equipment is performing under high demand for reliability and performance. In order to further increase performance, automated loading has been commissioned on one of the LHD’s and is being tested. Results to date indicate improved performance with respect to an operator through better filling of the bucket, fewer passes at the muck pile and shorter cycles. Noranda’s Brunswick mine is currently commissioning an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two ore passes. Expected operational advantages include increased system capacity and enhanced safety and comfort for the operator. Monitoring to date indicates that the trucks can operate reliably under the conditions imposed by mine production.

Sep 1, 2001

By A. C. Wingrove

The paper outlines the selection of a dewatered tailings backfill system for the Johannesburg Consolidated Investment Gold Division, and covers the following aspects: (i) 16 Shaft pilot testwork; (ii) engineering design problems relating to the Cooke 3 Shaft backfill operation; (iii) in-line mixing - applications with respect to the Randfontein Estates Gold Mine and Western Areas Gold Mine backfill operations; and (iv) pipeline friction losses.

Jan 1, 1988

By K. Grossauer, W. Schubert

For tunnelling in poor and heterogeneous ground a reliable on-site short-term prediction is required to allow a safe and economical construction. With the use of absolute displacement monitoring data and advanced software for evaluation of the data in combination with a routine update of the geological model a considerable increase in the reliability of the short-term prediction could be achieved. The paper deals with theoretical considerations, numerical studies and case histories from alpine tunnels in heterogeneous rock. Tunnelbau in schlechtem und heterogenem Gebirge erfordert auf der Baustelle eine verlaessliche Kurzzeitprognose, um ein sicheres und wirtschaftliches Bauwerk gewaehrleisten zu können. Die Verwendung von absoluten Verschiebungsmessdaten und deren Auswertung mit Hilfe von hoch entwickelten Softwareprogrammen in Kombination mit einer laufenden Aktualisierung des Gebirgsmodells ermöglicht eine erhebliche Erhöhung der Verlässlichkeit von Kurzzeitprognosen. Dieser Beitrag beschäftigt sich mit theoretischen Ansätzen, numerischen Modellen und Fallstudien von Tunnelvortrieben in heterogenem Gebirge. La construction de tunnels dans la montagne hétérogène de faible résistance exige un pronostic fiable à court terme sur le chantier, afin de pouvoir garantir un ouvrage sûr et économique. L'utilisation des données de mesure de décalage absolues et de leur évaluation à l'aide de logiciels sophistiqués en combinaison avec une mise à jour courante du modèle de la montagne permet une augmentation considérable de la fiabilité des pronostics à court terme. Cette contribution présente des approches théoriques, des modèles numériques et de cas pratiques de progressions de tunnels dans des montagnes hétérogènes.

Jan 1, 2003