Search Documents

By H. S. Sichel

This study deals with the development of some new theory concerning the bias which will result from the employment of the t-estimator if in fact the underlying distribution of ore values is not lognormal. It is found that the t-estimator is robust as long as the logarithmic variance is small and the shape factors of the transformed distribution are not unduly large. The choice of the threshold parameter [t] for the t-estimator is important, and some hints are given how to estimate it if the sample size is small, as en- countered in borehole valuation problems.

Jan 1, 1987

By C. Snyman, M. Le Roux, Q. P. Campbell, S. Engelbrecht

Due to the ultrafine particle size required for effective processing of chromite ores, dewatering of the concentrates presents a challenge. It is not uncommon for the ore to have elevated moisture contents even after dewatering, which must be reduced to required levels of between 8% and 10% by mass for further processing. Contact sorption drying has shown promise in test work on fine coal. This method was used to study the dewatering of chromite on a laboratory scale using 3 mm spherical activated alumina ceramic beads as a sorbent. Three different sorbent-to-chromite mass ratios, namely 0.5:1, 1:1, and 2:1, were tested with different process conditions, including dewatering in a stationary and a rotatingl bed. The experimental work showed that it was possible to achieve the target moistures in less than 10 minutes, irrespective of the sorbent-to-chromite ratio used. Ratios of 1:1 or higher, however, proved to be the best. The sorbent reusability at mass ratios of 1:1 and 2:1 were therefore tested. With a 1:1 mass ratio, the sorbents could be reused for three cycles, while with 2:1 ratio, the number of cycles increased to six. The sorbent-to-chromite mass ratio used had a significant influence on the required contact time and the reusability of the sorbents.

Oct 3, 2023

By M. Ye. Scheglov, G. I. Voiloshnikov, S. M. Ryakhovsky, V. E. Dementyev, V. N. Alekseev, N. S. Voiloshnikova

Irgiredmet has substantial experience on RIP and RIL technology for gold recovery, having started development of ion exchange technology in 1964. Irgiredmet specialists were involved in the majority of RIL and RIP projects in the former Soviet Union and Russia, and took part in commissioning of practically all plants using ion exchange technology. Laboratory and pilot plant tests were conducted to develop process design criteria for designing 15 RIP plants of the former USSR using bifunctional macroporous anionite AM-2B or its analogs. This paper is devoted to the laboratory, pilot plant testing and introduction of RIP technology conducted in cooperation with GC Pertopavlovsk. Medium base resin PuroLite S992 (PuroGold) was used as adsorbent. Some adsorption regularities and the affinity of resin to metal cyanide complexes were studied. Laboratory batch and continuous pilot tests on resin-in-pulp process were held for oxidised ores from Pioneer, Albyn and Malomyr mines (Amur region, Russia) owned by the Petropavlovsk company. A simplified flowsheet for gold elution and resin regeneration was developed. Alkaline cyanide solution was used as gold eluent and gold was recovered from eluates by electrowinning. Process design criteria were developed on the basis of the testwork results, and the plants were designed and constructed by GC Petropavlovsk. The RIP plant at Pioneer was commissioned in May 2008, at Malomyr in August 2010, and at Albyn deposit in December 2011. These plants are currently in operation at design performance at throughputs from 3 to 6.5 Mt/year. The primary gold ores of Pioneer and Malomyr deposits are refractory to cyanidation; Irgiredmet also completed continuous testwork on RIP technology using medium-base resin for pressure oxidation (POX) residues derived from their flotation concentrates. In 2019 a hydrometallurgical plant for the treatment of refractory gold concentrate after POX was commissioned at Pokrovsky mine (Amur region). Keywords: Gold ores, cyanidation, RIP, RIL –processes, ion exchange resin, medium base resin, adsorption, elution, electrowinning

Jan 1, 2020

By K. Dewar

The catalytic converter industry is composed largely of global multinational manufacturers who supply to vehicle manufacturers (original equipment manufacturers ? OEMs) from facilities strategically located internationally, including plants in South Africa. The South African catalytic converter production facilities were established at the request of the OEMs and commenced manufacture in the early 1990s. This near 100 per cent export focused industry exists in South Africa because of the incentives offered by the Motor Industry Development Programme (MIDP), which ultimately provide the OEM with import duty rebates. The South African catalytic converter industry is a complex vertically-integrated supply chain with a local content in excess of 85 per cent, substantially more than any other exported automotive component. The industry remains one of the very few downstream manufacturing industries where South Africa has a significant global footprint. This is even more important when it is considered that this industry is the key end-user for two of South Africa?s most important mineral resources, namely platinum group metals (PGMs) and chromium, and is in an industry which will see massive global growth as the developing nations of the BRICs grow their auto industries. In over 15 years of existence in South Africa, the catalytic converter industry has achieved remarkable growth, averaging compound growth in the region of 14 per cent per annum. The industry is the highest contributor to automotive component export revenue. South Africa holds >8 per cent% of global PGM reserves. During 2011, South Africa supplied 59 per cent, 29 per cent, and 72 per cent of the global demand for platinum, palladium, and rhodium respectively, as well as over 50 per cent of the global chromium demand. Global autocatalyst production remains the largest consumer of PGMs, and South Africa alone beneficiated 15 per cent of locally mined PGMs in the production of catalytic converters ? all is converted from PGM sponge (powdered metal) into PGM solutions for coating onto catalysts. Beneficiation of PGMs also takes place via the production of jewellery and electronic goods; but compared to catalytic converters, this volume is negligible. The industry is also the largest consumer of locally produced stainless steel (>50 000 t/a), exceeding 38 per cent of local consumption. The industry is a substantial generator of highly skilled employment, with over 5 000 direct jobs (excluding OEMs and stainless steel manufacture) and an estimated more than 30 000 indirect jobs resulting from upstream and side-stream suppliers. The industry places a high focus on skills transfer and development, with all companies providing high-tech training and education both locally and overseas. The industry has invested in excess of R5 billion in plant, equipment, people development, and process development over the last 15 years to support transfer of production and new technologies to South Africa. This has resulted in significant skills development in the support industries as well as within the catalytic converter industry. The current projections for local PGM beneficiation via catalytic converters reflect a downward trend as a result of production being moved to other global locations due to uncertainty around changes to government incentive programmes. The industry is currently capacitated to support 23.7 million units per annum. During 2011 it utilized about 70 per cent of this capacity, but forecast projections suggest that this will be at 46 per cent of this level by 2016. At full capacity the industry would represent 19 per cent of global autocatalyst production compared with the current 13 per cent in 2011. The industry believes that there is potential to make South Africa the preferred location for catalytic converters worldwide, given suitable support from the mines and Government.

Jan 1, 2012

By M. Rudman, L. Pullum, L. J. W. Graham

Centrifugal pumps are the workhorse of hydraulic conveying systems but their performance is derated when viscous non-Newtonian fluids, such as pastes and/or coarse solids are present. The reduced performance for purely viscous Newtonian fluids may be calculated using techniques such as the Hydraulic Institute method, but similar deration for non-Newtonian fluids is not so easy to apply. As part of the AMIRA P599 project investigating high concentration suspension pumping, centrifugal pump tests were systematically conducted on a wide range of non-Newtonian coarse particle suspensions. Suspension sup to 38% v/v of coarse particles with mean diameters in the range of 1.1 < d50< 3.4 mm suspended in carrier fluids with dynamic yield stresses of 0 < t?< 17.2 Pa and shear thinning indices in the range 0.35 < n< 0.79 were examined. Techniques such as the Hydraulic Institute de-ration method require a characteristic shear rate to be assigned before application with a non-Newtonian fluid, and a method based on pump geometry, fluid rheology and flow rate is proposed. This method predicts the dramatic characteristic reduction in head at low flow rates that is often observed and explains why larger pumps are relatively insensitive to this form of head deration. Head deration due to the presence of coarse particles in non-Newtonian carrier fluids is seen to follow similar trends to that of Newtonian suspensions and often dominates the total deration procedure.

Jan 1, 2007

By J. W. van der Merwe, A. M. Maleka, V. J. Matjeke

The 10.5–12.5% chromium, titanium-stabilized ferritic stainless steel (FSS) plates used to fabricate coal line jumbo wagons is susceptible to undesirable chromium depletion during welding with 309L electrodes. In this work, non-stabilized FSS plates were welded using 308L welding electrodes. The objective was to weld non-stabilized FSSs using gas-shielded metal arc welding without causing sensitization. The welding process was optimized by lowering the heat input. Sensitization was assessed by rigorous etching techniques and anodic polarization scans. In addition, the welds were subjected to tensile testing, and their fracture surfaces were examined for intergranular cracking. Non-stabilized FSS plates were successfully welded using gas metal arc welding.

Apr 5, 2023

By M. Abdellatif

"SynopsisCalcined basic nickel carbonate (BNC) concentrate was smelted in a pilotscale DC arc furnace to produce a nickel metal. The furnace was continuously operated for 12 days (24 hour/day), during which twelve different smelting conditions were investigated, with the major variables being reductant type and feed rate, flux composition and addition, and BNC feed rate.The 200 kW DC arc furnace was operated at power levels between 110 and 165 kW and at a total feed rate of 78 to 96 kg/h, resulting in an average slag and metal tapping temperature of about 1650°C. A total of 7.2 t of BNC were smelted, producing about 5.44 t of nickel metal and 2.94 t of slag. Nickel recoveries of 96.4% and higher were achieved, and the slag nickel content was as low as 0.1%. The major impurities in the metal were iron (mostly from oxygen lancing) and carbon. The calculated feed carry-over was less than 0.85% and the graphite electrode consumption was between 2.8–3.3 kg/MWh.IntroductionOne of the most distinctive advantages of DC open-arc smelting is the ability to process fine raw materials without any major issues with regard to the operability of the furnace, metal recovery, and metal quality. This has been demonstrated in Mintek’s DC arc pilot plant facilities over a period of about three decades (Curr et al., 1983). The materials that have been processed include laterite (Kotze, 2002), chromite fines (Curr et al., 1983), manganese fines (Lagendijk et al., 2010), PGM concentrates (Shaw et al., 2013), electric arc furnace (EAF) dust (Denton et al., 2005; Abdellatif, 2002a) and stainless steel (SS) dust (Denton et al., 2005; Abdellatif, 2002a; Goff and Denton, 2004), and petroleum fly ash (Abdellatif, 2002b). The top particle size of such materials can vary from a few millimetres (e.g. laterite) to micrometres (EAF and SS dust). Dusting, whether due to physical carryover of feed or to the arc side reactions, has been proven to be a non-issue. As such, the applications of DC open-arc furnaces have the potential to be extended to other raw materials such as particulate nickel oxide, which has a particle size much less than 100 µm.Nickel oxide is typically produced from laterite ore by sulphuric acid leaching, purification, and precipitation as basic nickel carbonate (BNC) (Rhamdhani, Jak, and Hayes, 2008) or as mixed hydroxide precipitate (MHP) (Mackenzie, Virnig, and Feather, 2006), and finally calcining at moderate temperatures (800–1200°C). The NiO product is very fine, with an average particle size in the range of 10–20 µm and a NiO content of more than 99%."

Jan 1, 2015

By T. Bohmer, L. Auret, N. Pillay, Z. Horn, P. Rambalee, A. Haasbroek

As part of a broader digital technology-enabled transformation programme, a major mining company is systematically implementing Advanced Process Control (APC) solutions and associated instrumentation throughout their operations. This paper highlights the approach and benefits of this holistic approach for a specific instrumentation installation, and APC installation at a South African coal processing plant. For the coal processing plant under consideration, a systematic approach was followed. Process sections/units are considered from upstream to downstream processing. APC solutions are designed for each process section and each process section is interrogated in terms of availability of sufficient process measurements to ensure stable, capable, and ultimately, optimised performance. Where insufficient process measurements are available, instrumentation upgrades are implemented. Finally, APC solutions are implemented, and evaluated in terms of productivity, safety, health, and environmental benefits. For the flotation section, an opportunity was identified to install froth sensors. The installed froth sensors provide measurements on froth velocity, bubble size, height, colour, and stability. The improved visibility that the froth sensors provided on the flotation process resulted in quick gains in terms of productivity: for example, instability in the feed to the flotation section could be quantified. This resulted in targeted process troubleshooting in an upstream thickener, and subsequent improvement of process stability, and reduced feed variance. The measurements from the froth sensors were further integrated in an APC solution. Proportional mass pull contributions per cell and per line can be inferred from the froth sensors, serving as controlled variables, while pulp level set points serve as the manipulated variables. On-off tests indicated that the advanced process control solution provided increases in yield and product quality.

Sep 1, 2021

By J. Cilliers, R. Seitz, D. Drinkwater

Mineral processing produces a saleable product from high-cost ore. The Mineral Processing Engineer must constantly improve the separation to create the most value from the ore and reduce the associated costs. Graduate Metallurgists (or Chemical Engineers) have had the university theoretical training required, but often are illprepared to perform their plant roles. The in-work Metcelerate programme was designed specifically to develop the practical skills that Mineral Process Engineers require, by combining three key elements: 1. Knowledge transfer through self-paced, on-line training; 2. Practical skills acquisition through assessed, practical plant exercises; 3. Skills development through online tutorials. A final process improvement project adds significant value to the operation that far exceeds the training cost. Experience from Metcelerate clients has indicated improved staff retention, greater confidence, and pro-active process intervention.

Jan 1, 2023

By J. A. Maritz, D. F. Malan

Pillar strength is affected by pillar shape, but this has largely been ignored in past research studies. Bord-and-pillar layouts are typically designed using empirical strength equations developed for square pillars. Owing to the poor quality of pillar cutting, many hard-rock pillars have an irregular shape and it is not clear how this affects pillar strength. Furthermore, the strength of rectangular pillars in comparison with square pillars is also difficult to quantify. The ‘perimeter rule’ is widely adopted for rectangular pillars, but its applicability for pillars with irregular shapes has never been tested. We used numerical modelling in this study to investigate the effect of pillar shape on strength. An analytical limit equilibrium model of a square and a strip pillar also provided useful insights. For slender pillars, the strength of a long rib pillar is essentially similar to that of a square pillar. In contrast, for rib pillars with a large width to height ratio, there is a substantial increase in strength. The study found that the perimeter rule should not be used for irregularly shaped pillars. Displacement discontinuity modelling, using a limit equilibrium approach, is proposed as an alternative to determine the strength of these pillars.

May 3, 2023

By H. Jiang, W. Wang, Y. Zhao, J. Qiao, C. Duan

DEM simulations were used in this research to study the screening process of a novel variable amplitude equal thickness vibration screen (VAETVS). The response regularity of mass distribution and granular moving velocity at the different screen panels to feed rate was investigated and the predictive model for the unit area processing load was proposed. The influence of aperture size, the size variance, and the opening ratio on the mass passing-distribution and overall screening performance, respectively, were revealed. The results showed that the response model of the unit area load Ф to the feed rate Q can be concluded as Ф∝0.324×Q. The moving velocity of particles also showed a positive relevance to the feed rate, besides which the passing rate of fine-grained material at the feed end was negatively related to the aperture size, while the case was reversed in the feed end. The increase of aperture variance AV enhanced the passing ability of small particles at the feed end,and reduced the misplaced ratio of the large particles at the discharge end. A better screening efficiency can be obtained when the average aperture size of the entire sieve is 7.5 mm, with the aperture variance of 1 mm between the adjacent panels. When the combination of the opening ratio is 35-35-40, a better screening effect can be achieved. Keywords: Equal thickness screening, DEM, particulate velocity, mass distribution regulation

Jan 1, 2020

By A. Chuma, K. J. Nyembwe, H. Simonsen, J. H. Potgieter

Different concentration techniques were evaluated for preconcentration of a mineral ore at a coarser size to avoid energy and resource wastage. Specifically, the aim was to reduce milling costs and energy required in the beneficiation of tin. In this study, cassiterite (0.17% Sn) was the mineral of interest in a pegmatite ore body associated with quartz (SiO₂ > 60%) and alumina (Al₂O3 > 20%). Three concentration techniques, namely dense media, shaking table, and flotation, coupled with characterization analysis, were used to assess the concentration response. The results confirmed that particle size and mineral liberation impact the separation process. High recovery and grade were obtained with gravity concentration methods (dense media and shaking table) for coarser (+300 to +212 μm) and intermediate (+150 to +53 μm) particle sizes. Lower recovery and grade were identified for much finer sizes (−53 to −38 μm). Flotation produced a high-grade product at a relatively low recovery and appeared to be only applicable to finer grains. Separation efficiency based on Schulz’s equation measured a segregation performance of 74.8% for dense medium separation and 60.7% for the shaking table for the coarse and intermediate particle sizes. Flotation only achieved a separation of 30%–40%. The results suggest that use of dense media separation as a rough preconcentration method prior to further grinding, and the utilization of a more advanced concentration technique for mineral recovery and upgrade, constitute a successful approach to improve process economics.

Apr 14, 2024

By S. W. Jacobsz, E. P. Kearsley, N. K. Schoeman

A physical modelling approach was adopted to simulate the process of cave mining propagation at various horizontal to vertical stress state ratios, and image data was captured and used to characterize the resulting failure mechanisms. Image processing was integrated into the study to determine minor principal strains in models to identify where critical extensional strains had been exceeded relative to crack propagation. The study exhibited a scale factor magnitude of 119 using a calculated critical extensional strain value of 0.014% for the modelling material used. It was perceived that cave propagation occurred through successive parallel extensional ‘fracture bands’ in all cases, as noticed in models of prior studies, deviating from that described by the Duplancic model. Cracks tended to bisect regions of minor principal strain equal to the critical extensional strain, which suggests ‘fracture banding’ is an acceptable failure mode for brittle, rock-like materials. Moreover, it was found that models with lower horizontal to vertical stress ratios (K ratios) showed a greater degree of vertical development of the caving mechanism (at similar vertical stresses), while the vertical extent of the cave was suppressed in models with higher K ratios. Models subjected to larger vertical stresses experienced slower cave formation in latter time-steps. These models exhibited larger two-dimensional caved perimeters and areas, respectively.

Nov 30, 2022

By E. J. Magri

Consideration is given to the problem of the estimation, from limited data, of the likely grade and tonnage for a new mining property that is to be exploited by the selective mining of two metals that have substantial contributions to make to the total revenue. In particular, the case of a new gold and uranium mine in South Africa is analysed as follows. (I) The applicability of the underlying lognormal bivariate model for different support (i.e. ore unit) sizes is examined. (2) The necessary parameters for the bivariate lognormal models for different block sizes are estimated from abundant chipsampling data from a section of the Hartebeestfontein Gold Mine using alternative approaches, and the results are compared. (3) A method is given for obtaining the necessary parameters for a tonnage-grade relationship relative to a joint pay limit from the very limited information likely to be available at the end of the exploration stage of a gold mine, and the results are compared with those obtained from the large volume of data available from a minedout area.

Jan 1, 1982

By D. C. Krige

The estimation of the tonnage and grade of payable ore in a mine and the correct policy of selective mining based on such estimates, is of vital importance to the mining engineer it is surprising, therefore, that more attention has not been devoted on the Witwatersrand to the scientific improvement of mine valuation methods. At present these methods consist almost entirely of the application of simple arithmetic and empirical formulae guided by practical experience, and ignore the many advantages to be gained from a careful statistical analysis of the behaviour of the gold values. The science of statistics has expanded rapidly during the last two decades and its value as a powerful and indispensable tool is now recognized not only by research workers and scientists but also, ever-increasingly, by the commercial and industrial world. This being the case it is noteworthy that in a mining field such as the Rand with its highly developed and advanced mining methods, singularly little attention has been paid to the analysis of mine valuation problems on a modern statistical basis. This omission is even more striking when cognizance is taken of the wealth of sampling data concerning the gold ore which is available and of the far-reaching decisions and deductions constantly being based on such data. Some contributions have however been made from time to time towards the application of statistics to mine valuation on the Rand (References Nos. 7, 8, 9, 11, and 12), but none of these have been generally applied in practice and a systematic practical approach based on clearly deemed fundamental concepts still appears to be lacking. The object of this paper is, therefore, to define these statistical concepts and to indicate briefly the lines along which statistical methods can be applied profitability in solving some of the existing problems and in improving the general standard of mine valuation on the Rand For this purpose a knowledge of mathematical statistics is essential, but as this paper is primarily intended to provide the mine valuator with a practical introduction to statistical application in his field, the mathematics is confined to a short annexure, together with references from which details can be obtained.

Jan 1, 1994

"Coal seam gas problems can adversely affect the safety and productivity of underground coal mines, leading to fatalities and financial losses. Conventional gas management technologies using ventilation and gas drainage are unable to deal with the high and irregular gas emissions associated with high-production longwall mining. New technologies need to be developed to supplement the traditional gas management techniques to minimize the hazard of coal seam gas. Thin spray-on liners (TSLs) have gained some success for rock surface support since their introduction to the mining industry. Due to their relatively low permeability and appropriate mechanical properties, TSLs also show potential to be used as a gas management tool in underground coal mines.In this paper we review the current gas management challenges and discuss the potential use of TSLs as a gas management tool in underground coal mines. This may involve reducing gas migration into the excavations/roadways, enhancing in-seam gas drainage, and preventing spontaneous combustion. Some potential areas for future research work are identified. IntroductionWhen a coal seam is influenced by mining activities, gas stored inside is liberated into the underground ventilation system. Gas emissions have created serious difficulties for the coal mining industry around the world. Therefore, coal mines have to develop effective strategies to control the gas concentration below the threshold value to meet statutory requirements. Ventilation has been the first solution in gas management for underground coal mining. When the emitted gas cannot be effectively diluted by ventilated air, gas drainage using pre- and/or post-drainage has to be introduced. However, even with ventilation and gas drainage, irregular gas emissions usually increase the gas concentration in roadways and slow down the development rate, thus causing significant economic loss to the coal mining industry (Thakur, 2006). Therefore, new technologies need to be developed to address this issue and mitigate the explosion risk."

Jan 1, 2016

By M. N. Mathabathe, A. S. Bolokang, C. W. Siyasiya, R. J. Mostert, G. Govender

The b-solidifying g-TiAl intermetallic alloys of nominal composition Ti-48Al (binary alloy), Ti-48Al-2Nb (ternary alloy), Ti-48Al-2Nb-0.7Cr (quaternary alloy), and Ti-48Al-2Nb-0.7Cr-0.3Si (quinary alloy) (in at.%) were developed. The materials produced were tensile tested at room temperature. The as-cast microstructures and fracture surfaces of the tensile tested specimens were examined using conventional metallographic methods. Microstructural examination indicated that the alloys were comprised of lamellar structures (a2+g) embedded in columnar dendritic cores in the as-cast condition. However, the quinary alloy contained a Ti5Si3 second phase. The alloys exhibited no detectable ductility during tensile deformation, indicating the brittleness of all the materials. The fracture surfaces revealed that the alloys failed by translamellar fracture with correspondingly few cleavage facets.

Apr 1, 2021

By T. Uysal

Various morphological parameters that affect the flotation recovery of sphalerite were modelled and optimized using the response surface method (RSM). The effects of roughness value, shape factor, and collector concentration were investigated using the central composite full design method. The results were evaluated by analysis of variance. The optimum roughening time was found to be 25minutes, the optimum roughness value was 2.9071 μm, and the optimum collector concentrationwas 0.001 M. Using these values, a flotation recovery of 98.01% was obtained. Similarly, in shapefactor studies, the optimum grinding time was 15 seconds, the optimum roundness value 0.7421, and the optimum collector concentration 0.0009 M, which resulted in a flotation recovery of 94.30%. The average error between the optimization results and the experimental results was estimated to be less than 6%, and the R2 values were greater than 90%. The study shows that RSM can be effectively applied in finding the economic optimum condition for obtaining maximum flotation recovery with minimum reagent consumption.

Sep 6, 2023

By R. Sun, R. G. Gillies, R. S. Sanders, J. Schaan

The pipeline transport of paste, backfill or thickened tailings slurries is an important component of the tailings disposal process in many mines around the world. These mixtures contain significant fractions of fine (clay) and coarse (sand) particles, causing them to exhibit non-Newtonian flow behaviour and high frictional pressure gradients. There is often economic incentive to operate these pipelines in the laminar flow regime. Irrefutable evidence has shown that coarse particle settling can occur during the laminar flow of these slurries even when static settling tests show no indication of such behaviour. Previously, a ?rule-of-thumb? minimum frictional pressure gradient of ~1.5 to 2 kPa/m was suggested to ensure effective sand transport, based on the results of tests conducted using viscous Newtonian oils. In this paper, we examine the results of laminar flow tests of non-Newtonian, coarse-particle laden slurries conducted with pipeline loops of 50, 100, 150 and 250 mm in diameter. The results indicate that the ratio of the mean wall shear stress to the mean surficial particle stress is abetter indicator of laminar flow settling tendency than frictional pressure gradient.

Jan 1, 2007

By J. Sjöberg, T. Savilahti, S. B. Umar

"Sublevel caving in Malmberget mine results in mining-induced surface deformation. One of the currently mined orebodies is the Printzsköld orebody. As mining deepens there is need to assess the behaviour of the cave formed in the subsurface above this orebody. Numerical analysis was used to assess the effects of extraction to deeper levels and perform strength parametric studies. Stress redistribution was studied, and the results showed high stress buildups in the hangingwall and the crown pillar. Two failure mechanisms have been identified – shear and tensile. Reducing cohesion by 50% increased the area of the yielded zone by more than 100% in the hangingwall.IntroductionThe Malmberget mine is owned and operated by the Luossavaara-Kiirunavaara AB (LKAB) mining company. Iron ore is extracted by large-scale sublevel caving. The mine comprises a total of 20 orebodies, about 10 of which are in production today (Figure 1). The mine is located in the municipality of Gallivare, about 100 km north of the Arctic Circle (Figure 2).Successful sublevel caving requires progressive caving of the orebody after initial blasting. This results in caving of the hangingwall, sometimes all the way to surface, resulting in surface deformation. As mining progresses to deeper levels a larger area is affected by deformation. Over the years, extraction from the Malmberget orebodies has led to deformation of the ground surface, affecting residential areas and existing infrastructure.Forecasting the caving process is not straightforward as it can be rapid or slow, depending on the rock mass conditions, stress conditions, the failure mechanisms at work, etc. Moreover, several of the orebodies in Malmberget are non-daylighting, which makes reliable caving analysis even more difficult, primarily since there is less available experience from such cases. The present study was designed to improve the understanding of the caving and deformation mechanisms at Malmberget, and in particularly for the Printzskold orebody"

Jan 1, 2017