Search Documents

A method is proposed for the evaluation of the influence of grout prestressing systems on the support resistance offered by timber packs. It is shown that, in order not to reduce the load-carrying capacity of timber packs, grout prestressing systems need to be at least as stiff as a single timber rise. The method was used to establish strength specifications for the grout prestressing systems to be used under non-seismic and seismic conditions. For non-seismic requirements, the 24-hour grout strength needs to be at least 1,7 MPa, and the 7-day grout strength 4,9 MPa. The investigation showed that the proposed strength specification is realistic in the light of current grout-strength capabilities. For seismic requirements, the grout strength needs to be at least 4 MPa and 8 MPa to prevent extensive damage to the grout during seismic events with a peak velocity of 1m/s 3 m/s respectively.

Jan 1, 1996

By J. Petersen, S. W. Robertson

Heap leaching is used extensively for the processing of low-grade copper, gold, and uranium ores. The hydrodynamics is often the most important factor that limits the rate of metal recovery. Over the past decades the author has performed physical and hydraulic testing of a large number of ore samples considered for heap leaching. The data were reviewed to investigate the effect of physical properties such as particle size distribution (PSD) and bulk density on the hydrology. The unsaturated flow through the bed is traditionally modelled with soil science models such as Brooks-Corey (BC) and Van Genuchten-Mualem (VGM), which relate the hydraulic conductivity to the degree of saturation, also known as the hydraulic conductivity function (HCF). However, most authors found a disconnect between the saturated hydraulic conductivity (KS) and the rest of the HCF, which is explained as resulting from a transition from capillary-to gravity-controlled flow. However, the author found no such transition, and found the flow to be governed by capillary flow throughout. Traditional BC or VGM fits were found to be appropriate, however it was necessary to modify the model to include a point of inflection, above which the hydraulic conductivity remains constant while the moisture content keeps on increasing. It was proposed that this is the result of unconnected or poorly connected pores, which fill with solution but do not create additional flow channels. The point of discontinuity was also found to correspond with the air entry point, measured independently from the air conductivity curves. On average, the air entry point corresponds to the experiential rule that the void saturation should remain below 65% for aerated heaps.

Dec 11, 2024

By J .. F. Brownrigg

In the mining method used at O'Okiep Copper Company (OCC), vertical crater retreat, the prime requirement for the fill is that it should be sufficiently strong to be free-standing to a height of 150 m. Other requirements are minimal decant and drainage water, and high pulp density to allow large tonnages to be placed quickly and alleviate transport problems. The excessively high cost of cement precluded the use of a cement-based fill, and after three years of extensive investigations a backfill based on the smelter slag was produced. Currently a fill with a uniaxial compressive strength of greater than 1 000 kPa after one month is being produced. This is in excess of the design specification of 850 kPa after 2 - 3 months. The research and development which went into the slagfill is briefly covered; the production of the fill from the various raw materials is described; and the design and control systems of the backfill plant, the reticulation system and its monitoring are examined. Finally, the implications of this high- quality fill for the mining programme are assessed.

Jan 1, 1988

By J. P. T. Kapusta

"The copper smelting industry faces increasingly stringent environmental regulations and must continue driving innovation to reduce energy usage in its production chain. With the coming of age of ‘bottom-blowing’ copper technologies in China over the last decade, much renewed attention has been brought to tuyere bath smelting for clean copper-making. Since bottom-blowing sonic injection was originally developed and implemented in steelmaking in the 1970s and lead smelting in the 1990s, the time seems appropriate to revisit the sonic injection concepts and dispel some myths. After reviewing the trends in the copper industry and providing a brief historical context of research and development related to sonic injection, the author presents a comparison of the main submerged tuyere bath smelting technologies, namely the Noranda Reactor (NR), the Teniente Converter (TC), and the Chinese Bottom-Blowing Smelting Furnace (SKS/BBS) for copper, and the Queneau-Schuhmann-Lurgi Reactor (QSL) for lead. The core of this article, however, consists of a brief description of the fundamental theories for sonic injection (jetting regime) and ‘sonic flow mapping’ to illustrate the relationship between the minimum tuyere back-pressure required to achieve sonic flow and the tuyere internal diameter. The article also offers a comparison between side- and bottom-blowing in jetting regime before concluding with the author’s vision of the new trend in submerged tuyere bath smelting. IntroductionIn the last decade, developments in the copper smelting industry have been driven by two key concepts: (1) increasing cleaner smelting capacity to meet the world’s growing copper demand, as illustrated in Figure 1, and (2) increasing process off-gas capture to comply with more stringent environmental regulations and abide by a corporate social responsibility ethic of a clean work environment (for smelter employees) and clean air (for families living around smelters). The copper smelting industry has also faced some major challenges in the last few decades, including (1) low treatment and refining charges (TC/RC or processing fees) impacting custom smelters, (2) lower concentrate quality and grades with higher levels of impurities (e.g. As and Hg), (3) higher processing and transportation costs due to the rising cost of energy, (4) restrictions in process intensification (tonnage oxygen usage) due to furnace integrity limits, and (5) scarcity of educated and trained personnel due to fewer metallurgists graduating from pyrometallurgical school programmes combined with a high retirement rate of skilled workers."

Nov 1, 2018

By J. R. Bredell, J. Branehog, C. Coetzee, J. J. van Tonder

A nutating grinding mill, exemplified by the commercial HICOM mill, achieves efficient particle size reduction through the accelerated motion of the material charge within the nutating chamber. This design, characterised by high particle velocities and rapid charge circulation, offers a compact solution compared to tumbling mills. There have been concerns regarding the mechanical reliability of kinetic joints for certain specialised mining applications. Recognising the need to model internal forces in such systems, this study focuses on the uncoupled simulation using multibody dynamics and the discrete element method. The investigation employed a small-scale experimental test mill, referred to as the NuMILL, featuring a cylindrical chamber (140 mm internal diameter, 245 mm height, 6° nutation angle). Instrumented with an array of sensors, the NuMILL provided internal load data for validating the simulations. Experiments were conducted with an empty chamber or filled with charge material. Charge materials included coarse sand or steel pellets with a charge-to-chamber mass ratio of 0.25. The mill speed ranged between 100 to 700 RPM. Multibody dynamics modelled resultant inertial and frictional loads within 5%, while the discrete element method simulated the internal material contact loads with accuracies ranging from 1% to 19%. The combined simulation approach predicted the resultant forces in the critical kinetic joint within a 20% margin. Representing the charge using rigid lumped mass elements was also studied. The presented simulation techniques, validated against experimental data, offer a robust foundation for analysing larger systems, including the industrial-scale HICOM.

Mar 5, 2025

By Z. Halifa, P. G. Geyer

Tapping a blast furnace is necessary not only to deliver the product, but is also essential for the safety of the furnace and workers in the cast-house. This paper will highlight the practices at ArcelorMittal’s blast furnaces in the Vanderbijlpark Works, with specific focus on tap-hole design and monitoring as well as casting practice. Extension of the tap-hole life and hearth campaign will be illustrated with reference to the methods of maintenance of the tap-holes, troughs, runners, and cast-house equipment. The importance of proper cooling, good thermocouple installation, and temperature monitoring will be explained.

Jan 1, 2014

By J. van Zyl, K. B. Le Bron, L. J. Gardner

Pillar design is a crucial aspect of underground mining engineering, as it directly impacts the safety, stability, and overall effectiveness of mining operations. In this paper we present a method to calculate pillar stability based on the strain criterion and pillar load inversion concept, which complements the empirical pillar strength formulae. Those formulae do not account for certain parameters that can affect the stability of the pillars, e.g. weak layers, changes in stress orientations due to mining, orebody dip, mining layout complexity, and the influence of regional stabilizing pillars. The approach presented here is not intended to replace the empirical method; rather, we suggest using it as the initial step in the pillar design process. This should be followed by iterative numerical modelling to study pillar behaviour, define pillar stability, and optimize the pillar design by considering site-specific and representative rock mass properties and criteria.

Jun 10, 2024

By G. Chitiyo

Prediction of pothole characteristics is a challenging task, confronting production geologists at the platinum mines of the Bushveld Complex. The frequency, distribution, size, shape, severity and relationship (FDS3R) of potholes has a huge impact on mine planning and scheduling, and consequently cost. It is with this in mind that this study was initiated. Quantitative analysis of potholes indicates that pothole size (area covered) can be described by two partly overlapping lognormal distributions. These are referred to as Populations A (smaller) and B (larger). The range of observed pothole sizes conforms to a simple double exponential growth model based on Newton's Cooling Curve. A third size range of very large potholes (Population C) that could not be modelled properly within the proposed growth model is interpreted as to represent a very early phase of aggressive regional thermo-chemical erosion and potholing. In general, potholes are dominantly quasi circular with only a subordinate tendency of elongation. In the UG2, potholes with elongated forms are more prevalent in the size range between 20 and 500 m diameter. In the Merensky Reef elongated potholes are more common in the size range above 50 m in diameter. Although not distinctly visible, elongation of potholes in both the UG2 and the Merensky Reef show a net north/south orientation. Using shapes of pothole rims and floor areas, documented for the UG2 in the Waterval Shaft area, it is demonstrated that the northern, down-dip edges of potholes have steeper dips than the southern, up-dip edges. Spatial distribution studies using a uniform quadrant method suggest that in both the UG2 and the Merensky Reef, the potholes are randomly distributed, with a tendency towards clustering. Clustering appears to be more prevalent in the smaller Population A potholes. Bearing all findings in mind, it is found that the model of thermo-chemical erosion of the cumulus floor by new influxes of superheated magma best explains the observed data. Partial to complete melting of the cumulate floor occurred in three phases. The first represents the emplacement of hot magma. This magma, due to turbulent flow and high chemical and physical potential, aggressively attacks the existing floor (crystal mush on the magma/floor interface). Regional erosion is manifested by large, often coalescing potholes. During the second phase, when the magma emplacement process ceased and cooling in situ started, two distinct periods of pothole formation ensued. The first is related to rapid cooling along the relatively steep part of the Newton Cooling Curve, when Population B potholes nucleated randomly and grew rapidly with concurrent convective overturn and largely laminar flow condition. The second period of cooling occurred on the shallow-dipping part of the Newton Cooling Curve. Population A pothole growth became more subdued and nucleation appears to have been, at least locally, clustered. The final phase of this proposed 'super magma cycle' was introduced when chromitite crystallization and precipitation terminated pothole formation. This was followed sequentially by pyroxene and plagioclase crystallization to form the typical cyclic units of the Critical Zone. No suitable proxy could be found for the prediction of pothole density of potholes associated with the UG2 (likely due to limited spatial data coverage), and these are best predicted by extrapolation. The Merensky Reef slope index, in contrast, provides a proxy for pothole density, enabling prediction with reasonable confidence. This predictive model has been verified using underground information. The findings made during the course of this investigation have, when implemented, significant impact. Successful implementation will not only allow enhanced resource and reserve definition, but also better mine planning and scheduling.

Jan 1, 2008

By J. P. Gouvea, T. R. Stacey

A research project was carried out on a gold mine in the Vaal River region of South Africa (Witwatersrand Basin) to evaluate the effect of two particular aspects of rockbolt installation – the angle of inclination of the bolt relative to the orientation of the rock surface, and the protruding length of the bolt – on the mine’s gully support system. A keyblock analysis approach indicated that these factors do not have an adverse impact on the stability of the strike gullies. This was confirmed by extensive empirical data collected from the case study mine. While safety is the primary concern, cost saving opportunities can be realized through reconsidering historically inherited support standards that are perceived to be correct and appropriate. The research described in this paper sets forth a practical approach, that is easy to implement and repeatable, to evaluate the role of rockbolts in stoping gullies.

Feb 12, 2024

By D. V. J. W. Groenewald, T. M. Louw, L. Auret, S. M. Bradshaw, A. V. Cherkaev

Unexpected equipment failures lead to financial losses due to production disruption. Time-based maintenance, based on checks over regular time periods, has been employed to minimise disruption. However, the improvements it can offer are limited as it may lead to unnecessary service of healthy equipment or missed failures occurring between service intervals. Condition-based maintenance (CBM) provides a further improvement to equipment reliability by detecting faults and predicting remaining useful life (RUL) based on equipment health monitoring. Its application in the mineral processing industry is hindered due to the high cost of health monitoring equipment. In this study, two stochastic process models, the adaptive auto-regressive model and the gamma process, are compared in their ability to forecast the degradation state and to provide RUL prediction. The gamma process model was found to be effective in both tasks. Due to its simplicity and minimum hyperparameters requirements, it is proposed to use the gamma process as a baseline for comparison with other models. Keywords: Condition-based maintenance, remaining useful life, slurry pump, adaptive autoregressive mode, gamma process

Jan 1, 2020

By N. Naude, L. S. Leal Filho, M. P. Tshazi

In this paper, the authors performed experiments in the Denver and Leeds laboratory flotation devices at the University of Pretoria at various particle sizes to evaluate the performance of the devices. Quartz was used in a single mineral system at discrete sizes fractions, -25 μm, +25- 45 μm, +45-75 μm, and +75-106 μm. Hydrodynamic analysis, based on dimensionless power and Reynolds numbers, indicated that the Leeds cell required higher power input to achieve comparable flow conditions. Specifically, the Leeds cell exhibited an average power number of 1.03, whereas the Denver cell averaged 0.77 within the same impeller speed range of 1000 rpm–1500 rpm. For comparative flotation performance, impeller speeds were calibrated, resulting in operating speeds of 1200 rpm for the Denver cell and 1400 rpm for the Leeds cell. The cells performed similarly at two coarser-sized fractions. However, some deviations were observed in the finer particle size range. The -25 μm (fine) fraction initially achieved a recovery of only 15%. An additional reagent dosage was required to enhance the recovery of this fraction significantly. These findings highlighted the influence of particle size on flotation recovery. For all experiments, the Denver laboratory flotation cell outperformed (defined by higher recovery) the Leeds device, while still operating at a lower impeller speed. This advantage can be attributed to its impeller-stator design and air dispersion features, effectively overcoming slurry resistance and resulting in superior flotation performance compared to the Leeds cell.

May 27, 2025

By van der Merwem J. N.

"Coal pillars are prone to scaling over time, and are progressively reduced in size and consequently subjected to increased load and reduced strength. The effective factor of safety therefore reduces. Databases of failed and stable pillars cannot, therefore, be regarded as definitive.More than a decade has passed since the first attempt to predict the lifespan of pillars. This paper presents a review based on the new database and pillar strength equations. The methodology for the analysis is based on the fact that pillars scale. The ultimate safety factor (defined as the ratio between strength and load at the time of failure) is derived, followed by an estimate of the rate of pillar scaling, which results in an estimate of the expected time of failure.It is suggested that the predicted lifespan should not be used as an absolute indicator of expected pillar life, but rather as an index – the pillar life index (PLI) – to complement the safety factor and related probability of failure when evaluating pillar stability. A pillar with a predicted lifespan of less than 500 years would be regarded as being in danger of imminent collapse, while a lifespan of at least 1 000 years should be required for long-term purposes.The differences between this analysis and that published in 2003 constitute a strong case for regular reviews of all the empirically based stability indicators, namely the safety factor, probability of failure, and the PLI. Reviews at 10 year intervals appear to be required.The constants in the proposed method are valid only for the Witbank No. 1, 2 and 4 seams and the Highveld No. 2 and 4 seams.IntroductionIt is well known that over time, coal pillars are prone to scaling, and thus are progressively reduced in size and consequently subjected to increased load and reduced strength. The effective factor of safety therefore reduces and it is quite possible for failure to occur after a long time interval. In fact, scrutiny of the database of failed pillars indicates that failure occurred after periods ranging from 2 to 49 years, and not immediately after mining.The factor of safety for pillars at the time of failure is not the same as that immediately after mining. The concept of the safety factor is based on the pillar strength obtained by statistical analysis of pillar dimensions immediately, or within a month after mining, when the surveys are conducted. Strictly speaking, the safety factor as commonly used is valid only immediately after mining, and it continues to reduce thereafter. The ideal situation would be to base analyses of pillar strength on pillar dimensions at the time of failure, but that is simply not possible because the real dimensions cannot be measured at that time."

Jan 1, 2016

By J. H. Zietsman, W. J. Leipoldt

"To be able to responsibly develop a multiphysics model of the steel belt sintering (SBS) process used to sinter chromite fines, it is important to have a comprehensive understanding of the process. This understanding was gained through a site visit, observation of the process in operation, and interaction with the operators. Material characterization will also reveal much about the process that is not yet fully understood. A well-defined and representative mass and energy balance will also give valuable insight into the process. The plan for the multiphysics model aims to combine a computational fluid dynamics (CFD) model with a discrete element method (DEM) model.To obtain a more accurate mass and energy balance representation of the SBS process, it was decided to develop a dynamic distributed parameter model of the mass and energy balance. This model will be used to gain better understanding of the SBS process so that a more complicated multiphysics model can be developed later. The reason for this is because the SBS process is very dynamic, with a large temperature distribution throughout the length of the process. In its current state, the mass and energy balance model is capable of handling solid and gas material packages and exchanging heat between these packages where they are mixed, and is able to model the heating of the gas by burning CO gas. The next step in the development of the model will involve enabling it to handle evaporatoin of liquid water, burning of solid carbon in the pellets, reduction of iron oxide in the pellets with the CO gas formed from carbon combustion, and then oxidation of the reduced iron in the oxygen-rich cooling zones."

Jan 1, 2014

By O. Dahl, B. Musuku, N. Schreithofer

Recovery of fine pentlandite is proving to be a challenging task in the Kevitsa sequential flotation operations, with over 60% of the nickel losses reporting into the -25μm size fraction. Since commissioning, the Kevitsa process has undergone major changes to address throughput and flotation performance. Major changes were implemented in the configuration of the milling and flotation circuits as well as in the operating conditions and reagent regime. Some of these changes improved nickel flotation while others deteriorated flotation performance. Most of the changes have had a direct impact on nickel flotation. This paper reviews the systematic analysis, laboratory testing and salient changes done to the process with special focus on the impact on the fine pentlandite flotation. Keywords: Blending, Flotation, Chalcopyrite, Pentlandite, Fines

Jan 1, 2020

By A. Singh, R. D. Govender

The current method employed to quantify the efficiency of separation of ferromagnetic ores by wet low intensity magnetic drum separators (WLIMS) incorporates the use of a conventional benchscale Davis Tube (DT) operating at a magnetic field intensity that is equivalent to that of the drum’s surface. However, empirical research has indicated that the magnetic force, or force index, rather than the magnetic field intensity, is the critical factor in the operation of the magnetic separator (Murariu and Svoboda, 2002). Furthermore, the current aforementioned practice would yield incorrect information as the magnetic field gradients produced by a typical WLIMS unit differs considerably from that of a bench-scale DT. In light of this, research on magnetite focusing primarily on the scale-up of DT results to pilotscale WLIMS were undertaken. The investigation entailed a comparative study between that of a typical WLIMS circuit and a bench-scale DT. The purpose was to practically evaluate the performance of a WLIMS, bench-marked against the traditional laboratory-scale DT unit. Moreover, the secondary objective was to produce a magnetite concentrate graded at 69% Fe, 95% -45μm, as a suitable source of separation media for use in the Dense Medium Separation (DMS) industry. Fundamental findings of previous works provided a framework for the study, however, a realworld approach was explored. Preliminary testwork conducted at Mintek investigated the performance of a DT and a typical multi-stage laboratory-scale WLIMS circuit (operating at 1000 Gauss at the surface). The results attained indicated that a DT operating at high intensities is comparable to a single rougher WLIMS stage. Additionally, it was observed that the three stage laboratory-scale WLIMS circuit performed similarly to the DT operating at 1000 Gauss. Moreover, piloting testwork was undertaken, carried out in larger 380mm drums, and the results attained showed a strong correlation with laboratory-scale findings. Keywords: Davis Tube, wet low intensity magnetic separation, magnetite

Jan 1, 2020

By P. K. Jain

A spiral concentrator is a density separation device used for the beneficiation of coal and various minerals such as iron ore, chromite ore, gold, beach sand minerals etc. The flow pattern developed in the equipment is complex and unique, yet the operation is very simple, with low capital and operating expenditure. Spirals are applied for beneficiation of material in the size range finer than 2 mm and are capable of recovering heavy minerals as fine as .01 mm. The understanding of the unique flow pattern has kept researchers engaged over the last few decades and attempts are being made to explain such flow patterns so that they can be controlled and modified to improve the operating efficiency, Ep (Ecart Probable Error, also known as probable error in separation) and acceptability of spiral concentrators for processing of fines and slimes - currently being discarded and dumped in the tailing ponds. An attempt has been made in this paper to explain the generation of complex flow patterns with application to classical solid mechanics in the fluid and slurry system. The same has been used to explain the selective separation of particles in different zones in a cross-section on the spiral trough. The paper also discusses the application of a force balance model to explain the generation of secondary circulation. Due to the presence of laminar and turbulent flow regimes in the spiral concentrator, varieties of equations have been proposed in the literature, consisting of different equations for different zones. An attempt has been made to present a unified flow equation for calculation of flow velocity at different positions on the spiral trough. Keywords: Secondary circulation, spiral concentrator, density separation, fine particle processing

Jan 1, 2020

By E. Arghavani, S. H. Amiri, S. Zare, F. Sepehri, M. Ramezanizadeh

Mineral processing plants include different stages like crushing, grinding, classification and concentration, all of which have partially affect the final product. To identify and solve the related problems of each stage, process audition should be carried out continuously to find the major solutions of improving product and decreasing the maintenance and operating costs. The Iranian Gohar-Zamin iron ore beneficiation plant consists of equipment such as gyratory and cone crushers, high pressure grinding rolls (HPGR), ball mill, dry and wet double-deck vibrating screens, hydrocyclones cluster, magnetic drum separators, thickener and horizontal vacuum belt filters. The defects of initial design as well as current non-standard operating conditions of equipment were monitored and detected and the opportunities for process optimisation were presented as follows: establishing the control loop of power draw for cone crushers, the modification of feeding chute in cone crushers to minimise the non-uniform wear of parts, removing segregation in the fresh feed bin and screen’s circulating load chute in order to provide the proper feed to HPGR, reducing wear rate on HPGR rolls surfaces, decreasing the amount of rejected materials in screen, equalising the solid content and particle size distribution (PSD) of feed in all magnetic drum separators and equalising the PSD of hydrocyclones overflow. This paper provides a guideline for the mineral processing industry to focus its efforts on process design to deliver the efficiency with minimum capital costs. Keywords: Process audition, gyratory crusher, cone crusher, HPGR, screening, hydrocyclones, magnetic drum separators

Jan 1, 2020

By J. Preussner, U. Glatzel, R. Völkl, S. Prins, M. Wenderoth

Platinum base alloys are very corrosion resistant and have got a high melting point. Similar to Ni-base superalloys, which are used for jet turbines, the hardening effect of the intermetallic L12Pt3Al phase is used to receive a material that is creep resistant at high temperatures. Chromium is added to the alloy system to stabilize the L12phase down to room temperature. With the right amount of nickel the misfit and shape of the precipitates can be controlled. Various alloy compositions have been melted and analysed. With scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) a microstructure can be observed, which is very similar to the one in Ni-base superalloys. To support alloy development with simulations, a thermodynamic database of the Pt-Al-Cr-Ni system is about to be established. The SEM and EDS measurements provide useful input to the thermodynamic optimization. Also many data from the literature have been used to receive the best approximation. The Cr-Pt binary phase diagram has been reassessed and the latest results of thermodynamic modelling are presented.

Jan 1, 2006

By V. Oberholzer

The presence of fines (particles smaller than 6 mm in diameter) causes hydrodynamic problems in gasifiers and therefore it is of great importance to minimize the amount of fine coal in the feed. This serves as motivation for understanding coal?s breakage mechanisms, which could lead to the ability to predict the generation of fines. The aim of this project was to simulate the pulsating effect of the conveyor belt in order to investigate factors influencing the breakage. Results indicated that an increased initial particle size had an increasing effect in the amount of fines generated. Weathering had an insignificant effect on the breakage of coal. To conclude, a breakage model was developed to describe the rate of breakage out of the top size when a combination of two breakage modes is present.

Jan 1, 2009

By A. Tosun

"The size distribution of the muckpile formed as a result of open pit blasting operations has a considerable effect on the efficiency of loading, hauling, and crushing. Various researchers have developed specialized computer software that uses image analysis methods for determining the size distribution of the muckpile. However, these methods have some limitations. One of the most important of these limitations is that the very fine fragments in the muckpile cannot be used in the size distribution calculation. In this study, 18 test blasts in total were carried out in two limestone quarries belonging to Batiçim Corp. in Izmir, Turkey. A new model was developed in order to ensure that very fine fragments are used in the size distribution calculation. The size distributions of the test blasts were calculated by both the Wipfrag computer program and the new model. Correlations were established between the muckpile size distributions determined by both methods and the parameters determining the efficiency of the loader. IntroductionThe size distribution of the muckpile formed as a result of open pit blasting operations has a considerable effect on the efficiency of loading, hauling, and crushing. Various researchers have established certain correlations for predicting the efficiency of the operations according to the muckpile size distribution so that production can be carried out economically (Tunstall and Bearman, 1997; Nielsen and Kristiansen, 1996; Workman and Eloranta, 2004; Michaud and Blanchet, 1996; Frimpong, Kabongo, and Davies, 1996; Osanloo and Hekmat, 2005; Molotilov et al., 2010). In these studies, the 50% passing size (X50) is generally used. These methods rely on the correct measurement of the size distribution of the muckpile formed by the blast. The most reliable measurement method would be to subject the entire muckpile to a sieve analysis, but this is obviously impracticable. Therefore, computational method based on image analysis have been developed. These include IPACS (Dahlhielm, 1996), Tucips (Havermann and Vogt, 1996), Fragscan (Schleifer and Tessier, 1996), Cias (Downs and Kettunen, 1996), GoldSize (Kleine annd Cameron, 1996), Wipfrag (Maerz, Palangio, and Franklin, 1996), Split Desktop (Kemeny, 1994), PowerSieve (Chung and Noy, 1996), and Fragalyst (Raina et al., 2002). In these methods, the size limits of the fragments forming the material are determined by image analysis on photographs of the muckpile. However, the computer software has some limitations. It does not take into account the third dimension of the muckpile, nor the size distribution of very fine fragments. In particular, the fragment size ranges below 2.5 to 3 cm cannot be determined, and therefore these cannot be included in the muckpile size distribution. However, the muckpile formed by a bench blast contains a wide range of particle sizes (Tosun et al., 2015)."

Oct 1, 2018