Search Documents

Table B-1. Summary of respirable coal mine dust samples collected under 30 CFR 90 by MSHA inspectors for underground occupations, 1988-92* [ ]

Jan 1, 1997

By J. C. Edwards

Fire experiments were conducted in the Safety Research Coal Mine (SRCM) at the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, with coal, diesel-fuel, electrical-cable, conveyor-belt, and metal-cutting fire sources to determine the response of fire sensors to products-of-combustion (POC). Metal oxide semiconductor (MOS) and smoke fire sensors demonstrated an earlier fire detection capability than a CO sensor. This capability was of particular significance for a conveyor-belt fire in which the optical visibility was reduced to 1.52 m with an increase in CO of less than 2 ppm at a distance of 148 m from the fire. Application of a neural-network program to the sensor responses from each type of fire source resulted in correct classifications of coal, diesel-fuel, cable, belt, and metal-cutting combustion with a mean of 96% of the test data correctly classified.

Jan 1, 2000

By R. Raines, S. P. Signer

Researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health installed 39instrumented, fully grouted bolts at six test sites in a trona mine retreat panel to study mine roof stability for the improvement of workplace safety. Variables at each test site included bolt spacing, bolt length, roof span, and location in the panel layout. At most test sites, two rows of instrumented bolts were installed, one in or near the intersection created during development and the other in or near the intersection created during second-pass mining. The most significant factor affecting bolt load was roof span. The highest loads were on the bolts installed in the intersections of the 6-m-wide entry. Mining-induced stress resulting from panel layout was the next most significant factor affecting bolt loading. Minor variations in bolt loading could be attributed to changes in bolt spacing and bolt length. Gas pressure release in the immediate roof contributed to some bolts showing compressional loading during gas bleed-off.

By R. V. Ramani, V. T. Burgos, J. A. McClay

This report was prepared by The Pennsylvania State University under USBM Contract No. G0111808. The contract was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of DMSE, with Mr. G. R. Schottler acting as the technical project officer. Mr. J. A. Herlckes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this contract during the period June, 1971 to September, 1974. Thls report was submitted by the authors on February 13, 1975.

Jan 1, 1975

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C. 7 Emergency Rescue Hoists There is a need, especially in mine development areas, for portable, on-call, man-rated equipment capable of lifting men through several hundred feet. Wire rope climbing equipment as shown in Figure 37 appears particularly suited to this need. It is portable, weighing approximately 100 lbs. , is currently man-rated for numerous above ground applications and can be electric or air powered. Commercial units currently have a lifting capacity of 1000 lbs. , and can be fitted with bosun' s chairs. Lifting speeds are in the 20-30 FPM range and the equipment is not depth limited. In a situation where miners are unable to climb to the top of a shaft this equipment could rapidly be anchored to the top of the shaft and lowered to them by hand. Since the self contained unit is controlled by the person travelling in the shaft he would be able to negotiate shaft obstruction himself. This would not be possible with other forms of easily deployed free-hanging equipment. Typical manufacturers of this type of equipment are Ohio Hoist Mfg, Co, 321 South Beaver St. Lisbon, Ohio 44432 216-424-7283 Sky Climber Inc. 17311 South Main St. Gardena, California 90248 213-321 -6414

Jan 1, 1976

By R. Larry Grayson, Douglas F. Scott

Data on health-related illnesses and disease in the mining industry are scarce, and information on rates and costs is not readily available. Substantial amounts of research are being directed to addressing these issues, including work at the National Institute for Occupational Safety and Health’s (NIOSH) mining health and safety laboratories in Spokane and Pitts-burgh. This paper briefly discusses the current status of some miner health-related issues, including those involving coal dust, silica dust, diesel particulate matter, asbestos, noise, lead, welding fumes, and skin disorders, as well as research and other activities aimed at protecting miners from occupational illnesses and disease.

By A. S. Griffiths, J. E. Evans

Noise processing experiments with ELF (3 to 300 Hz) atmospheric noise and signals in the 40 to 80 Hz range are described. The primary purpose of the experiments was to record and analyze wideband ELF noise in order to design the noise processing portion of a receiver which minimizes the required transmitter power. The application of appropriate theory and extensive simulations led to a noise processor which consists of the following functions: (1) a compensating (or whitening) filter, (2) a prenotch filter clipper, (3) notch filters at frequencies of manmade interference (e. g., power lines), (4) a post-notch filter clipper, and (5) a phase-coherent linear matched filter. The nonlinear processing provides considerable gain relative to a linear receiver (i. e. , a receiver consisting only of a matched filter and appropriate whitening filters). It is convenient to measure sys tem performance in terms of an "effective noise level" which is equal to twice the received signal energy divided by the signal to noise ratio at the matched filter output. For example, the highest effective noise levels observed at 45 Hz with the nonlinear processor were about -134, -131 and -137 dB wrt 1 amp/m [Hz] using Saipan, Malta and Norway data, respectively, compared to 1 percent exceedance levels of effective noise for the linear receiver of about -115, 115 and -130 dB wrt 1 amp/m [Hz] respectively.

Jan 1, 1973

By R. V. Ramani, A. S. C. Owili-eger

The Federal Coal Mine Health and Safety Act of 1969 (sec. 303 (b)) stipulates that no working section of the mine shall contain more than 0.5 percent carbon dioxide and no harmful quantities of other noxious or poisonous gases such as the oxides of nitrogen. The concentration of methane should at all times be maintained below one percent. A split of air returning from any working section shall contain no more than 1.5 percent of methane (sec. 303 (i) (2)) and air that has passed by an opening of any abandoned area shall not be used to ventilate any working place in the coal mine if such air contains more than 0.25 percent of methane (sec. 303 (j)). Methane concentration in the returns from the bleeder entries should not exceed 2.0 percent (sec. 303 (i) (3)), and no air that has passed through an opening which is inaccessible for examination shall be used to ventilate any active areas. While the air quantity requirements alone can easily be met, the governing condition in most mines is the dilution requirements for quality control. A sufficient quantity of air is required to render harmless and carry away noxious and respirable pollutants. In recent years, changes in coal extraction methods, rates of advance, location of available reserves, position of prominent methane sources and horizons, and geological sequences have contributed sig¬nificantly to alterations in rates, patterns and character of numerous methane emissions. Gas production of 10 to 15 million standard cubic feet per day is not uncommon from deep mines (Cervik, 1969). Thus, because of the large capital outlay involved in the instal¬lation and subsequent remedial actions of methane drainage systems, knowledge of gaseous flow patterns and storage characteristics of the

Jan 1, 1974

By Robert L. Chufo

The paper, "An Electromagnetic Roof and Rib Thickness Sensor" presented at The 12th WVU International Mining Electrotechnology Conference in 1992, presented the results of roof coal thickness measurements in underground mines and rib coal thickness measurements in highwall mines. The microwave sensor described uses a unique spatial modulation scheme created by antenna motion, along with frequency domain signal processing, to solve the problem of media, target, and antenna dispersion. This paper further describes the advantages of the unique frequency domain signal processing technology chosen by the U.S. Bureau of Mines in extending previously reported one-dimensional thickness measurement technology to the generation of a full three-dimensional underground image of the underground environment. The electromagnetic signature of a media, whether it is coal or other geological material, is its permeability and permittivity and the effect on the velocity and amplitude of an electromagnetic wave as it passes through. High-quality imaging cannot occur without the identification of, and correction for, the permittivity and permeability of each layer of a multilayer geological deposit. Clutter, or any signal that can interfere with target discrimination, usually comes from objects in the field of view for which there is no design control. These are nuisance targets with possibly very high contrasts compared to the real target. The only proven tool to reduce clutter is to increase spatial, spectral, and polarization diversity. This paper will describe some techniques being used by the U.S. Bureau of Mines to increase the information content of both single-dimensional and three-dimensional imaging systems through the identification of media distortion mechanisms made possible by the use of spatial/spectral sensor technology. These techniques will permit high quality imaging in an environment where the data is corrupted by dispersion and clutter.

By P. R. Bremner

In keeping with its mission to maximize mineral and metal recovery from domestic sources, the Bureau of Mines investigated a method to extract silver from tailings not amenable to cyanidation. Results of a laboratory study on the recovery of silver from cyanide tailings containing 1.7 ounces of silver per ton by leaching with an acidic ferrous chloride-sodium chloride solution are presented. The effects of reagent concentration and reaction time on the leaching of silver were investigated. A leaching solution containing 5 wt-pct NaCI, 2.5 wt-pct FeCI2, and 1.2 wt-pct HCI (for acidity) extracted 82 pct of the silver from the tailings during a 24-hour leach. The amount of HCI consumed during the leach was 46 pounds of HCI per ton of feed. Only 23 pct of the silver was extracted by conventional cyanidation. Ninety-nine percent of the silver was recovered from the pregnant solution by cementation onto iron powder.

Jan 1, 1982

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

The usual run time errors occur when illegal mathematical operations are attempted by MFIRE For exam¬ple, if the user enters a negative value for the input variable HEAT to model a heat sink or cooling station, a run tame error will occur because an exponential function is employed to better model the changing temperature dis¬tribution in the airways. DATA FILE ERRORS Two types of data file errors can occur. 1 An error may occur because the input data file itself is invalid This may be caused by: The data file cannot be found due to incorrect spelling, drive, or path specification Check the spelling and path at the prompt for location of the data file. The data file contains non-ASCII symbols Check op¬eration of the text processor to insure that only ASCII characters are produced Delete all non-ASCII and/or all out of place characters. 2 Data are accepted by the program, but are incorrect for the data types or ranges or the combination causes a data inconsistency This may be due to. An invalid character is located where a numerical value is required The input data value is outside the reasonable range The input data is insufficient to build the model for simulation. The input data exceeds the capacity of the program. PROGRAM ERROR DETECTION When the program is running, tracing messages are given on the screen indicating the group and lines of data that have been read and the section of the program that is executing Program termination indicates that problems are caused by the subsequent (not read) data file section. For each detected error, descriptive message starting with * ERROR * is issued and the program terminates. When a possibly wrong value and/or its calculated intermediate result is detected, a descriptive message starting with * WARNING * is issued and the program continues. If a modification of input value or calculated intermediate result is automatically made by the program, descrip¬tive message starting with * ATTENTION * is issued and the program continues. LOCATING ERRORS If a message indicates that the error condition occurred due to the data input file, locate and correct the data item. If no error message is issued, but the simulation results are not as expected, carefully check the list of input data shown in the output file WARNING messages and ATTENTION messages may reveal an error in the input data even though the program continues to operate Insure that the default values or modifications adopted by the program run are acceptable. Anomalistic data, though not incorrect or impossible, may lead to an unusual simulation For example, making a fan unusually powerful may prevent a normal strength fire from affecting the airflow distribution in the system Much care must be employed before considering an ex¬treme case. If a message indicates that the accuracy criterion in the temperature section of the program was not satisfied, a table detailing the current parameters of airways which have large fluctuation in the average air temperature from iteration to iteration is produced If the pattern of the parameters is clearly cyclical, while the variation of natural ventilation pressure is stable or cyclical from iteration to iteration, then, most likely there is no single equilibrium stage for the event If the variation of natural ventilation pressure decreases steadily though slowly, increasing the value of data item variables MADJ or ITN (on control line number 1) may allow convergence.

Jan 1, 1990

By H. M. Lawrence

"In the land-pebble district of Florida a lively interest in the possibilities of obtaining increased recoveries of phosphate rock is evident. Research in several directions is being carried on by companies operating in the district to increase the yields obtained by the washing plants. The Bureau of Mines is cooperating with this research program to promote more efficient plant practice and to avoid unnecessary depletion of mineral resources.Washing practice, as carried on in the district at present for the recover of phosphate rock from the crude ores or matrix, is not a complicated process. Flow sheets of the several companies are similar, although the equipment varies with the preferences of the individual operators. For disintegrating the matrix log washers are favored, although revolving drums equipped with flights to break up lumps of clay are also used. Fine sand is removed by screening. Vibrating screens have become well established in the district, although stationary flat screens and trammels are also employed.The writer acknowledges with appreciation the cooperation of the phosphate companies in the land-pebble district; suggestions and criticism by Will. H. Coghill, supervising engineer, Ore Dressing Section of the Bureau of Mines; and the laboratory assistance of J. O. Davie, J. W. Pamplin, and E. Roca, cooperative fellows of the University of Alabama.Losses in the Finer SizesOf the phosphate that is not recovered by present washing methods the greater portion is in the finer sizes. In these sizes the phosphate grains are accompanied by grains of sand - largely quartz - of the same size, and recovery of these phosphate grains as a commercial product is not possible by simple washing methods. Phosphate recoveries approaching complete extraction can only be effecte by applying metallurgical processes, either mechanical or chemical. As yet, most of these processes have not advanced much beyond the laboratory or perhaps the pilot-plant stage. Such processes may have some application to the beneficiation of phosphatic ores or washer rejects, but a discussion of them is not within the scope of this paper."

Apr 1, 1929

By W. K. Overbey

Knowledge of fracture systems in oil or gas reservoirs is essential to the efficiency of both primary and secondary production operations. A relationship was established between structural features of the surface and both natural and induced fractures in oil and gas reservoirs, thus providing a method of predicting the direction of rock fracture prior to field development and well completion. Correlations between the surface features and under-ground fractures resulted from analysis of joint strike measurements, bottom-hole impression packer surveys, photographs of hydraulically fractured wells, fracture data from oriented cores, in situ strain measurements from formation outcrops, and lineament analyses from aerial photographs. The mean orientation of surface fractures, lineaments, and stress field directions ranged from N 53° E to N 73° E, compared with an average orientation of N 63° E for the hydraulically induced fractures. Tectonic stress field was shown to influence the direction of hydraulically induced fractures. This report presents the details and application of techniques to obtain the orientation of the principal horizontal compressive stress field component and thus the direction of induced fractures.

Jan 1, 1971

By L. C. IlsLey, M. W. Means

The United States Bureau of Mines under provisions of Schedule 20 issues approvals covering complete operating units such as loading machines, room hoists, and storage-battery locomotives. Certain manufacturers design and build entire machines. Other manufacturers purchase a part or all of the electrical accessories from manufacturers of electrical equip- ment and assemble them, thereby making up a permissible unit. Before the assembler purchases electrical accessories for use in such contempla.ed units he may require certain information from the accessory manufacturer as to whether these par- ticular accessories are suitable for assembly in his proposed permissible outfit. In order to aid accessory manufacturers in marketing their product, a provision was incorporated in Schedule 20 whereby tests might be made on individual accessories and reports rendered as to the suitability of a given accessory for use in permissible assemblies. The section of Schedule 20 which permits this special work reads as follows:

Jan 1, 1932

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

The PC version of the program MFIRE contains many improvements and enhancements previously unavailable for the modeling of mine ventilation networks and the interaction of fires with mine ventilation Transient-state simulation with dynamic modifications of the ventilation system and mine, the fire, and resulting POC transport and ventilation alterations are accommodated with MFIRE. MFIRE is more flexible and provides more error checking, and more informational messages about prob¬lems with input files than its predecessor, the MTU-BOM code The desirable features of the MTU-BOM code such as calculation and identification of recirculation, the air to rock heat exchange, and the basing of calculations on mass flow rates have been retained. MFIRE is useful for the planning and analysis of ven¬tilation networks, simulation for emergency planning, and the evaluation of fire detector layout Inquiries relating to this program should be directed to the Bureau of Mines, Twin Cities Research Center, 5629 Minnehaha Avenue South, Minneapolis, MN 55417

Jan 1, 1990

By J. V. Batty, K. C. Dean, H. D. Snedden, W. J. Long

As a part of the investigation of strategic-mineral deposits in the United States under the Strategic Minerals Act, engineers of the Bureau of Mines examined and sampled numerous deposits of fluorite ore from Utah. From those deposits that warranted further investigation, samples were submitted to the Ore Dressing Section of the Salt Lake City Station for metallurgical testing. This paper gives data summarizing the results obtained from laboratory ore-dressing studies of the fluorite ores submitted. Test work was done on samples from four properties in the Washington Mining District, Beaver County; two properties in the Star Mining District, Beaver County; one property in the Wah Wah Mountains, Beaver County; and three properties in Tooele County, Utah. In general, the Washington District ores were found amenable to concentration by flotation for the production of acid-grade fluorspar. None of the other ores were beneficiated to acid-grade, but several were amenable to concentration for the production of metallurgical-grade fluorspar concentrates.

Dec 1, 1947

By Richard F. Link, George W. Gladfelter, George S. Koch

Contour maps, useful in mineral industries, for example, in analysis of trends in mineralization, may be constructed through statistical methods of regression analysis programed for an electronic computer, For many applica­tions, the resulting maps are more useful and objective than conventional contour maps that are necessarily subjective because they are drawn by hand methods. In principle, an equation is found that fits a quadratic surface to observed elevations of points referred to a datum plane, The quadratic sur­face, represented by a contour map may take the form of a ridge, valley, dome, or basin, Once an equation has been derived, its coefficients may be used to construct a contour map--showing lines of equal value that are derived from the original observed data points by the averaging process of fitting the quadratic surface. Methods employed are illustrated by an example analysis, based on data from a large vein of the Fresnillo mine, Zacatecas, Mexico. Computer programs to implement the methods are described in an appendix,

Jan 1, 1964

By J. V. Batty, K. C. Dean, H. D. Snedden, W. J. Long

As a part of the investigation of strategic-mineral deposits in the United States under the Strategic Minerals Act, engineers of the Bureau of Mines examined and sampled numerous deposits of fluorite ore from Utah. From those deposits that warranted further investigation, samples were submitted to the Ore Dressing Section of the Salt Lake City Station for metallurgical testing. This paper gives data summarizing the results obtained from laboratory ore-dressing studies of the fluorite ores submitted. Test work was done on samples from four properties in the Washington Mining District, Beaver County; two properties in the Star Mining District, Beaver County; one property in the Wah Wah Mountains, Beaver County; and three properties in Tooele County, Utah. In general, the Washington District ores were found amenable to concentration by flotation for the production of acid-grade fluorspar. None of the other ores were beneficiated to acid-grade, but several were amenable to concentration for the production of metallurgical-grade fluorspar concentrates.

Dec 1, 1947

By Clyde E. Eilliams

In recent ye.ars much intere,t has been centered on the possibility of pro­ducing alumina from clq, a.nd proposed methods tor the recove:r,v of alumina are appearing constantly in parent lit,erature, As a good· grade of clay contains from 30 t<> 40 per cent of al"WDina, the prospect of tecovering it is alluring, al though obviously ditfieul t. A patent typical of m projected thermal processes is that 0£ Paul Migu.et, (U, S, Patent No, l,376,563) entitled nprocess for the preparation of pure alkaline alu:ninates.'' Re proposes to prepare alkaline a.luminate by fusing clay, lime, and acrap iron with a reducing aget in the electric furnAce, thereby reducing the silica a.r.d formin1s calcium alumina.te and ferrostlicon, The calcium aluminate, being lighter, would. float on top substantially free from foreign oxides, It could. then be tapped ott, cooledf ana later crushed and leached with aodium carbonate solution to torm, by double decomposition, sodium aluminate, and calcium carbonte. The fonMr is soluble and yields readily aluminum hydroxicie. 'l'he ferrosilicon wo'Uld be r,covered as such and sold at a profit.

Aug 1, 1922

By John C. Edwards, Gene F. Friel, John J. Opferman, Robert A. Franks

A series of diesel fuel fire experiments were conducted in the Pittsburgh Research Center&apos;s Safety Research Coal Mine (SRCM) to determine products-of-combustion (POC) spread rates along a single entry under zero imposed airflow conditions. Six experiments with an average fire intensity of 330 kW and three experiments with an average fire intensity of 30 kW were conducted in a 1 80 m long entry which had an average 2 m height and 4 m width. POC spread rates were measured by the response time of diffusion type CO detectors, positioned at 30 m intervals, to CO concentrations 5 ppm above ambient. For the 330 kW fires, average POC spread rates of 0.22, 0.13, and 0.06 m/s were determined at 30.60, and 90 m distances from the fire. For the 30 kW fires these average spread rates were reduced to 0.08, 0.04, and 0.04 m/s. The measured maximum roof layer temperature 30 m from two of the 330 kW fire was 30 and 36"C, which is less than the 57°C alarm point of a typical mine thermal sensor. It was determined that smoke detectors can be more effective for mine fire detection than CO detectors. The experimentally determined POC spread rates can be used to provide guidance for specification of sensor spacing to improve early fire detection at zero or very low air flows.