Search Documents

By H. E. Powell

Because of increasing consumption of high-and super-duty refractories, the Bureau is studying the feasibility of beneficiating submarginal and marginal clays. Diverse mineral dressing tests were used to beneficiate samples from the east-central Missouri fire clay district. Standard ASTM tests were used to determine refractory properties of both crude and beneficiated clay samples. Marginal and submarginal clays containing impurities were effectively beneficiated by both wet-cyclone and wet-table treatment, but the wet-cyclone treatment was cheaper. Ion-exchange resins in the hydrogen form will probably prove more effective in removing potassium, the only alkali in Missouri fire clays to be a problem. Resins with greater cross linkage are more effective than resins with less. Roasting the crude clays before removing alkalis by chemical leaching was ineffective. By applying ultrasonic energy at a frequency of 10 to 25 kilocycles to aqueous suspensions of the clays, subsequent ion-exchange extraction of potassium was slightly improved. Higher frequency ranges did not help.

Jan 1, 1963

This chapter describes the adverse health effects associated with exposure to respirable coal mine dust. Epidemiological studies of underground and surface coal miners in the United States and other countries are discussed. Also discussed are animal studies that add to our understanding of particle deposition and retention in the lungs and associated disease responses. This chapter emphasizes studies that (1) were performed since the passage of the Federal Coal Mine Health and Safety Act of 1969 [P.L. 91- 173], (2) used standardized methods of exposure monitoring and disease classification, and (3) investigated exposure-response relationships between respirable coal mine dust exposure and disease. Several published review articles contain further discussion of health effects studies of coal miners [Attfield and Wagner 1992b; Petsonk and Attfield 1994; Cotes and Steel 1987; Merchant et al. 1986; Morgan and Lapp 1976; Morgan 1975].

Jan 1, 1997

By D. S. Kingery

The practice of using doors to control main ventilating currents in bituminous-coal mines is common throughout the industry. When doors are erected in pairs to form air locks, they are usually accepted as satisfactory by both State and Federal coal-mine-inspection agencies. A review of the contributing factors in recent methane ignitions showed that interrupted ventilation (often caused by doors latched open, destroyed, or damaged) was the principal cause of methane accumulations that subsequently were ignited.

Jan 1, 1958

By R. E. Mussler

Electrowinning of copper from chloride solutions in a diaphragm cell was studied by the Bureau of Mines. The copper powder product was shaken periodically from the cathode and removed from the bottom of the cell. The effects of copper concentration, brine concentration, copper chloride species, and cell voltage were investigated. Power consumption of 1.1 and 2.1 kW-hr/kg were obtained with cuprous and cupric chloride solutions, respectively.

Jan 1, 1975

By Robert J. Anderson

"Introductory Statement.In founding any kind of castings, even with the best practice, scrap castings are produced because of rejections for certain defects. Casting los¬ses are a serious source of financial loss in iron and steel foundry practice as well as, in brass and bronze, but they are particularly serious in aluminum foundry work because of the high value of aluminum. The indications are that in many aluminum foundries in the United States, the casting losses are at times high, and in some plants they are entirely too high when compared with average practice. Of course, defective castings have a residual value for remelting, but if much machine work has been done on a casting before it is scraped, the labor costs alone may exceed the value of the metal and even that of the rough casting.In a foundry, the monetary losses incurred through the production of waster castings can be ascertained from calculations based upon adequate scrap-loss reports. Such reports, when properly kept and interpreted are a valuable aid in finding foundry costs, but they are primarily useful in diagnosing the causes for casting losses. Many aluminum foundries in the United States do not keep adequate records of strap losses; as a result the causes for defective castings can not be traced, nor preventative measures adopted. However, some of the large aluminum foundries keep excellent records, and it has been found that these involve little extra expense for clerical work. If a foundry man will study his daily production of defective and waster castings, he will be able to trace the causes or losses and then make such corrections in his plant practice as will effect a considerable reduction in these losses -- as much as 50.0 per tent in some foundries. If all the present casting losses of the United States could be reduced 50.0 per cent, by eliminating only the readily preventable defectives, a saving of several million dollars would accrue. In the aluminum-foundry industry alone, the saving would amount to about $600,000."

Apr 1, 1920

By E. D. Gardner

About five minutes after 3 o'clock on Thanksgiving morning, November 24, 1927, smoke was discovered coming up No. 2 shaft of the Magma Copper Co.'s mine at Superior, Pinal County, Arizona. Of the 49 men in the mine at the time, 42 were able to make their way to the outside unassisted, but 7 perished. Six bodies were recovered, and the seventh, that of an Apache Indian cage-tender at No. 2 shaft, is thought to be in the caved section between the 1,600 and 2,250 foot levels A second and independent fire broke, out in No. 1 shift about 2 a.m., November 27, burning .out the shaft timbers from the surface to the 200-foot level and destroying the surface fan and structures. About 20 men were underground fighting the fire in No. 2 shaft, but all were safely withdrawn, aril the fire in No. 1 haft was quickly controlled.

Jan 1, 1928

By Charles E. Whieldon

The importance of recovering more oil from known petroleum reserves has placed increased emphasis on the application of secondary-recovery methods. It is hoped that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases. A previously published report4/ described the highly successful results of waterflooding in the Weir sand in eastern Kentucky. A more recent report5/ evaluated the results of waterflooding in Roane County, W. Va. (See fig. 1.) Two waterflooding projects have been operated in Pleasants County, W. Va. (fig. 2), one by the Dearborn Oil & Gas Corp. in the Cow Run sand near Calcutta, McKim and Washington districts, and the other by George C. Schoonmaker in the Maxton sand at Bens Run, Union district. This report report describes the waterflood operation near Calcutta, W. Va.

Jan 1, 1960

By John A. Organiscak

The Bureau of Mines has recently completed a program to identify and evaluate various methods that address control of dust generated outby the longwall mining face. Dust generated by the stageloader-crusher, the panel belt, and the intake roadway can be long-term throughout the shift, contributing significantly to the dust exposure of all face workers. Dust control techniques were identified and tested at a number of longwall mining sections located in diverse geological conditions across the United States, Dust controls investigated include (1) methods that eliminate the sources of intake dust contamination--homotropal ventilation; (2) methods to limit the amount of respirable dust released into the intake airstream--improved water application and the use of curtains and enclosures; and (3) methods to clean the contaminated air prior to delivery to the mining face--scrubber systems. Usually they can be implemented at a low cost and can be very effective. This report describes each technique and its application and presents the resulting conclusions.

Jan 1, 1986

By R. B. Tippin

Research investigations conducted on five ore samples show the applicability of heavy liquid separation (HLS) techniques to mineral processing. Under proper operating conditions, semicontinuous tests in small fluid cyclones yielded 90 percent sink-float concentrates with recoveries exceeding 90 percent on minus 35-mesh ore samples of kyanite, potash, spodumene, fluorspar, and beryl. Although none of the ores were examined in detail, their response to this novel concentration method provides basic examples that are typical of the process. Various aspects of cyclone design and operational characteristics of heavy liquid cyclone circuits were studied which demonstrated the flexibility of HLS by using multiple units connected in series. A comparison of two heavy liquid solutions, tetrabromoethane and methylene bromide, exhibited their individual advantages and limitations. Unique problems relative to this process are discussed including liquid viscosity, mineral composition of the ore, toxicity, and material handling hazards.

Jan 1, 1968

By J. C. Nigro

Hematite-to-magnetite reduction kinetics were investigated mainly in CO-CO2 atmospheres at temperatures ranging from 500° to 1,000° C. Reduction rates were measured with a thermobalance, which recorded the weight loss as the specimen was reduced. Reduction data on both synthetic and natural hematite spheres showed good linearity of ro [1-(1-R)1/3] with time, t, up to over 85 pct conversion to magnetite; the rate coefficient (k[L], cm/min) obtained from the linear portion of the plot was used to characterize the penetration rate of the hematite-magnetite interface. Gas composition, porosity, and silica content were major factors affecting the rate. Temperature dependency of the reaction rate was small, yielding a mean activation energy of about 3 kcal/mole. Silica additions increased the reaction rate, probably through an increase in the effective surface area and diffusion; however, above 900° C, silica can react to form fayalite. Experimental data showed that the linear thickening rate of the magnetite layer, normally evidence of a chemically controlled reaction, can also be indicative of a reaction controlled by both mass transfer and diffusion. Evidence from this study indicates that the dominant rate-controlling factor in the reduction of hematite to magnetite at high temperatures is transport in the gas phase.

Jan 1, 1973

By M. M. Tilman

The Bureau of Mines conducted research to determine whether it is possible to substantially improve the fatigue resistance of lead sheet by means of surface coatings. Five types of coatings were applied to unalloyed chemical lead sheet. Flexural tests revealed that the best fatigue resistance was obtained with coatings of vacuum grease. Vacuum-grease coatings on unalloyed lead sheet resulted in fatigue resistance at least as good as that of the fatigue-resistant alloy Pb-0.04 Ca. Coated lead sheet was also tested in short-time tensile tests and in tensile creep tests. Tensile and yield strengths were increased by several of the coatings with only moderate loss of ductility. Creep resistance was also improved in varying degrees by most of the coatings. The Bureau also conducted research on the effectiveness of noise barriers by using sheet lead in combination with other materials. Noise barriers consisting of continuous-cast sheet lead with gypsum board were found to be effective and relatively inexpensive barriers.

Jan 1, 1978

By R. D. Leitch

The pollution of streams by acid mine drainage has become of great importance in the past few years in certain regions of the United States. Large quantities of acids are used in a discharged from other industries than mining, notably in tube, sheet, tin-plate and era hell inn works. These are usually less important then coal mines as a source of acid drainage, because of their more limited distribution throughout the States most affected by acid waters and their relatively smaller numbers. Streams are naturally alkaline and are, therefore, able to take care of rather large quantities of acid wastes, but when such enormous quantities as are often found in mining districts enter the streams, the natural alkalinity is quickly overcome. When a neutral or almost neutral condition has been reached, the further addition of a relatively slight quantity of acids will cause a great difference in the quality of the water.

Jan 1, 1926

Synthetic dawsonite [NaAl(OH)2C03] has been prepared with crystallinity similar to that of dawsonite found in oil shale deposits of the Piceance Creek area of Colorado. Optimum experimental conditions were as follows: Na/Al atomic ratio, 43; temperature, 175° to 200° C; pCO2, 15 psig; and reaction time 5 hr. Chemical and spectrographic analysis revealed that the synthetic dawsonite was of high purity and Has essentially stoichwmetric. Similarity of the synthetic to natural dawsonite, demonstrated by X-ray diffraction, infrared spectrophotometry, and electron microscopy, suggests its suitability as a standard.

Jan 1, 1972

By Aarne Visnapuu

Experimental modifications have been made by the Bureau of Mines on standard pneumatic rock drills to reduce the noise of the air exhaust, drill steel resonance noise, and noise radiated by the drill body. A close-fitting case and muffler around the drill body, consisting of a metallic honeycomb skeleton filled with viscoelastic absorber on the inside and a durable outer shell, provide both exhaust and drill body noise muffling and absorption. Drill steel resonance noise is reduced by a constrained-layer treatment consisting of a tubular metal cover bonded to the ouside of the rod by a viscoelastic filler. Damping alloy components have been developed to reduce metallic resonance noise. Combined, these modifications have reduced the drilling noise level in granite from 115 dbA to 97 dbA. Data are presented on the individual and combined effects of these modifications on drilling noise and performance.

Jan 1, 1975

By Daryl E. Radcliffe

Ninety-seven roof bolts were instrumented with strain gages and resin-grouted in three areas of the Bear coal mine, Somerset, Colo., by the Bureau of Mines. Measurements taken with these instruments indicate roof support is achieved through a combination of point suspension and resistance to vertical and horizontal stresses caused by localized shearing in the roof. The localized shearing results in bending of the bolts, yielding due to high vertical stresses, and the transfer of high loads to the bolt head or plate.

Jan 1, 1980

By Albert E. Long

Diamond-bit performance and cost data accumulated in core-drilling sandstones reveal significant trends of economic interest. Large-size, AA-Grade drill bort suffered less diamond loss per foot drilled than any other size or grade of diamonds assessed. Detailed analyses of the factors that affect diamond-bit performances -diamond size, diamond quality, bit size, bit type, percentage of core recovered, and physical characteristics of bit matrices -are assessed in the tables, graphs, and discussion. INTRODUCTION Since 1945 the Bureau of Mines has been compiling detailed performance records on diamond bits used in core drilling throughout the United States and Alaska. Analytical reports covering bit performance in various rocks are issued as in-formation on a significant number of bits used in anyone type of rock is accumulated. The first three such reports analyzed bit performance in gneiss,2/ schist,3/ and lime-stone and dolomite.4/ This report evaluates diamond-bit performance in sandstone. Data obtained from 627 bits, which drilled 42,665 feet on 45 different projects, are presented. The geographical distribution of the projects is shown in figure 1.

Jan 1, 1958

By Kelly C. Strebig

Laboratory tests were conducted by the Bureau of Mines to determine the effect of depth of cut and bit type on respirable coal dust generation. Apparatuses were constructed to contain the coal samples, measure the linear cutting forces, and analyze the dust generated. Single-bit tests were conducted in Illinois No. 5 and Pittsburgh seam coals with five bit types at four depths of cut. The results showed that bit type did not significantly influence dust production. On the other hand, deep-cutting bits were more efficient and generated substantially less respirable dust per pound of coal broke than shallow-cutting bits.

Jan 1, 1975

By Ronald D. Hill, Elmore C. Grim

Some of the terms defined here are not used in the text. However, the terms will be useful to those interested in this and other publications in the field of coal surface mining.

Jan 1, 1974

By R. L. Montgomery

Heats of solution of cerium metal and cerium (III) chloride in hydrochloric acid were measured. The standard heat of formation of the aqueous cerium (III) ion at 25° C is -166.1 ± 0.3 kcal/mole. Heats of solution of cerium (III) chloride in hydrochloric acid are consistent with the existence of a complex CeC1++ having a stability constant of 1 and a heat of complexing of 5.4 kcal/mole.

Jan 1, 1962

By R. O. Kneisley

Rock mechanics measurements indicate that the present two-bed mine design used at the Big Island trona mine, Green River, Wyo., results in stable workings. Vertical pressure changes in the lower panel pillars and horizontal pressure changes in the lower bed roof and floor indicated negligible upper bed mining influence. Pillar stresses stabilized soon after upper bed mining was completed. Strata movements in the pillar ribs, roof, and floor were also negligible and stabilized soon after completion of upper bed mining. Using tributary area theory, the confined core approach, and studies of model trona pillars it is shown that increased extraction ratio is possible. A program of gradually increased extraction ratio accompanied by simple measurements should result in a mine design that includes both higher recovery and long-term stability.

Jan 1, 1981