Search Documents

By Fred N. Kissell

Methane-flow and pressure data taken from a mine in the Pocahontas No. 3 coalbed are compared with flow rates from lump coal obtained in laboratory experiments. From this, it is concluded that the main source of gas is the intact coalbed rather than a "crushed zone" near the working face. The permeability and sorption capacity of the intact coalbed are calculated and gas emission rates are theoretically accounted for.

Jan 1, 1972

Control dust generated during undercutting in salt mines without causing ore-solubility problems that result from excessive water use. Approach A foam generator was developed to provide a reliable foam to control dust on cutting machines used in mining water-soluble ores. The system was designed to keep total foaming agent/water mixture flowrates below the flow-rates characteristic of water-only systems. The foam generator consists of a reservoir to hold the premixed agent and water, a metering pump, and a small compressor to aerate the mixture. The system is compatible with all cutting machines. How It Works One of the current wet-bar techniques, the through-the-bar trickle system, pumps water through a pipe in the cut-ting bar to its tip placing the water behind the kerf. If the pipe conducted foam effectively the foam would be released in the kerf where it would mix with the cuttings and the dust produced by the chain. For improved foam delivery, however, it is recommended that the pipe be replaced with an external channel welded along the top of the bar. This provides excellent dust control while avoiding the accumulation of copious quantities of foam in the heading. The system is very simple. The foam generator is a 50-gallon tank filled with a mixture of water and foaming agent. The mixture is pumped through a wye fitting to a second line where it is mixed with compressed air, (300

Jan 1, 1984

By Thomas P. Holden, Todd M. Ruff

Problem: An average of three workers a year are killed in surface mining operations when a piece of haulage equipment collides with another smaller vehicle or a worker on foot. Another three workers are killed each year when haulage equipment backs over the edge of a dump point or stockpile. Devices to monitor the blind areas of mining equipment are needed to provide a warning to operators when a vehicle, person, or change in terrain is near the equipment. Method: A proximity warning system (PWS) based on the global positioning system (GPS) and peer-to-peer communication has been developed to prevent collisions between mining equipment, small vehicles, and stationary structures. Results: A final system was demonstrated using one off-highway haul truck, three smaller vehicles, and various stationary structures at a surface mining operation. The system successfully displayed the location of nearby vehicles and stationary structures and provided visual and audible warnings to the equipment operator when they were within a preset distance. Summary: Many surface mining operations already use GPS technology on their mobile equipment for tracking and dispatch. Our tests have shown that it is feasible to add proximity warning to these existing systems as a safety feature. Larger scale and long-term tests are needed to prove the technology adequately. Impact on Industry: A PWSs that incorporates a combination of technologies could significantly reduce accidents that involve collisions or driving over an edge at surface mining operations.

By Steven M. Shope

The Bureau of Mines electromagnetic trapped miner location and communications system requires a thorough understanding of through-the-earth electromagnetic wave propagation. An earth model incorporating a magnetic dipole buried in a three-layered earth has been developed. The dipole source is located in the second subsurface layer. By application of proper limiting values, the three-layered model is reduced to two different two-layered models and eventually to the homogeneous half-space model. The solutions are in the form of infinite integrals. A numerical analysis was carried out and a computer program written to evaluate the surface magnetic fields. Numerical values for the magnet- ic field at the point above the source are presented in a variety of models.

Jan 1, 1982

By C. H. Schwartz

A thermal radiation probe was constructed and tested in pulverized-coal-fired furnaces. A rotatable sensing head on the side of a water-cooled probe permitted measurement of radiant flux within a 7.20 cone from any desired direction to a point within a furnace. A response curve for a corner-fired furnace showed radiant flux of 130,000 Btu per sq ft per hr, when viewing flame, and 60,000 Btu per sq ft per hr, when sensing wall reflection. Detailed drawings and fabrication procedure are given.

Jan 1, 1970

By L. E. Schultze

The Bureau of Mines operated a mineral recovery unit to recover metal values from post-flash geothermal brines from the Salton Sea known geothermal resource area as part of its research into the use of plentiful resources. The brine was available for metals recovery after its heat content had been used to generate electricity. The brine source was treated with lime to precipitate the contained iron, manganese, lead, and zinc before injection of the heat-depleted brine into the underground reservoir. Data are presented on the effects of process variables, such as rate and method of lime addition and air oxidation versus air exclusion. Variations in precipitation of metal values, composition of precipitates, effectiveness of slurry thickeners, and methods of treating the precipitates to recover metal values are discussed.

Jan 1, 1982

By P. W. Jeran, C. M. McCulloch, Maurice Deul

The natural vertical fracture sys tem in bituminous coalbeds is called cleat. Cleat orientation commonly controls the direction of mining with major development paralleling the face cleat. Previous researchers have categorized the origin of cleat as endogenetic, relating the origin of cleat to compaction and coalification, and exogenetic, relating the origin of cleat to tectonic forces. In the coalbeds studied for this report it was found that tectonic forces were the controlling factor of cleat formation. Face cleats were formed as extension fractures during structural deformation, and butt cleats, as release fractures during erosion and uplift. The face cleat of the Pittsburgh coalbed rotates from N 80° W in north- western West Virginia to N 57° W in southwestern Pennsylvania ; the face cleat maintains a perpendicular orientation to the shifting axial trend of local structures . Cleat orientation in other bituminous coalbeds in Virginia, Utah, Oklahoma, and Central Pennsylvania showed a similar relationship to local structure. Directional permeability of coal is directly related to cleat. Holes drilled perpendicular to the face cleat yield from 2.5 to 10 times the amount of gas released as compared with holes drilled perpendicular to the butt cleat.

Jan 1, 1974

By C. A. Herbert

"The Bureau of Mines for a number of years has conducted experiments at its experimental mine near Bruceton, Pennsylvania, on the explosibility of coal dust, with particular reference to dust explosions in coal mines, and the knowledge so rained may well be applied to the handling of coal dust at industrial plants and elsewhere.Powdered coal is coming into use more and more as a fuel, and the dangers incident to its use should be recognized and guarded against, as a number of accidents have occurred in recent years due to ignorance of this danger or to carelessness.Within the past three years two very serious accidents, under almost identical circumstances, have occurred on the surface at two different coal mines in Southeastern Iowa, due in each case to the sudden ignition of a cloud of fine coal dust.The first accident resulted in the burning of six men, three of them fatally; the second burned eleven; three men died as a result of their burns.The mines in the Southeastern part of Iowa, where these two disasters occurred, are operating in a thin coal bed averaging about three feet in thickness, and are worked on the long-wall advancing system similar to that of Northern Illinois.The miners in this section are paid on a screened coal basis; in other words, receive no pay for the fine coal. As a result they use forks in loading the coal into the mine cars, and naturally a considerable quantity of coal is left along the roadways. Subsequently this fine coal, together with the roof rock that is taken down to give sufficient height on the roadways, is loaded into cars and dumped in piles on the surface. This roof rock is a block, oily shale and the contribution of fine coal and oil shale gives ample combustible material to thoroughly burn the rock as it is dumped."

Jul 1, 1923

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output.? It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1985

Develop a cost-effective diesel aerosol sampler that can be used by industry and regulatory agencies to determine the diesel exhaust aerosol concentration in mine atmospheres. The sampler must be easy to use, wearable by mine personnel, compatible with current personal sampling protocols, and inexpensive. Approach The University of Minnesota (University) and the U.S. Bureau of Mines (USBM) have developed and tested a prototype diesel exhaust aerosol sampler. The sampler, however, was complicated and expensive to fabricate. Consequently, the USBM redesigned the sampler to simplify both manufacturing and use, and the sampler was evaluated to ensure equivalency with the prototype. Background The National Institute for Occupational Safety and Health (NIOSH) has recommended that "whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration." In addition, the U.S. Mina Safety and Health Administration (MSHA) has been directed by an advisory committee to establish a diesel exhaust aerosol standard and regulations to minimize exposure to diesel pollutants in underground coal mines.

Jan 1, 1992

By R. L. Wise

Heat content studies were conducted on burned shale, spent shale, and three grades of raw oil shale from the Green River Formation. Corrections were made for product enthalpies. The results were compared with previous work, indicating good agreement below retorting temperatures, but some differences at retorting temperatures. A general equation was developed relating heat content to oil-shale grade and temperature.

Jan 1, 1971

By L. C. IlsLey

It is most unfortunate that a few must often suffer , and perhaps die , that many may benefit from a fuller appreciation of the dangers surrounding mining operations , and the proper use of safeguards designed to offset these dangers . This has been the case during the last few months in the anthracite field , where several explosions , resulting in burnings and fatalities , were undoubtedly caused by the use of defective or improperly assembled flame safety lamps . Had this same lack of understanding regarding the proper assembly of this safety device , and had the same indifference on the part of the user in keeping the lamps locked at all times and in proper condition , been permitted in a region where the coal dust was explosive , a terrible disaster would surely have resulted . In nearly every coal -mining country , including the United States , the Davy and Clanny type of lamp has been superseded , and rightly so , by some kind of bonneted lamp . Bonneted lamps , especially of the naphtha type , while much safer than the unbonneted , have more parts and need more care in assembling . For this reason the burden of responsibility for their being properly assembled rests with the lamp man ; therefore , it is extremely important that only competent , conscientious men be given this work .

Dec 1, 1921

By Thomas E. Marshall, Gerald L. Finfinger

The Bureau of Mines has developed a practical methodology for deter- mining occluded gas contents of domal rock salt samples. The method, which is portable and field worthy, provides results in 5 min or less and does not require a laboratory environment or specially trained personnel to obtain meaningful results. The results can be used to identify gas-enriched zones, and thus may aid mine operators in production planning or ventilation design. The test method is based on the relationship between gas content and the acoustic response of salt samples as they are dissolved in water. The relationship is defined by an equation, and the results are repeat- able. The equation was derived by testing a series of rock salt samples collected from domal salt mines in Louisiana.

Jan 1, 1987

By Jerry E. Olson

In 1986, at the request Of the Bureau of Land Management, the U.S. Bureau of Mines studied the central portion, encompassing 20,727 acres of the 32,261-acre Badlands Wilderness Study Area (OR-005-021) in order to evaluate its identified mineral resources. The study area is located in Crook and Deschutes Counties, OR, about 12 miles east from Bend. No mineral resources were identified. The area studied is underlain by Tertiary and Quaternary basalt flows which are largely covered by a veneer of sand and silt. No mines, prospects, or mineralized areas occur within or near the study area, but some sand and gravel has been removed from alluvial deposits at the east and west sides of the area. Slab lava of marketable grade and quantity was not found in the study area. None of the study area is of current interest for geothermal resources, but the eastern third of the wilderness study area is leased (1984) for oil and gas.

Jan 1, 1987

By Kenneth C. Stewart

Eight brands (three samples of each kind) of commercially available audio-dosimeters were performance-tested. Each unit was placed in an anechoic chamber and subjected to various acoustic signals to measure its A-weighting response and overall integration accuracy. All units met the A-weighting tolerance for type II sould level meters, and six brands were within the Bureau I s overall accuracy requirements of ±2 dbA referred to input.

Jan 1, 1974

By Ivette E. Torres

The series summarizing the prices of the major nonferrous metals on the stock exchanges of the United States and the United Kingdom (London Metal Exchange) has been continued this year in tables 22 and 23. Time constraints have prohibited preparation of other price information that has appeared in this study in previous years. Users are urged to consult the 1993 U. S. Bureau of Mines publication Metal Prices in the United States through 1992, which gives an analysis of historical price series and trends, or the 1993 edition of Mineral Commodity Summaries for current U.S. prices on non fuel commodities, and to utilize U.S. Department of Energy sources for information on fuel material costs.

Jan 1, 1994

Design and test a high-production coal mining machine that generates less respirable dust. Background Current coal cutting systems generate excessive amounts of airborne respirable dust and fines during the mining process. Dust control technologies, including dust dilution by ventilation and suppression by water sprays, are not always able to reduce dust levels sufficiently. The U.S. Bureau of Mines (USBM) has designed a cutting system that reduces respirable dust generated by the cutting action of the drum. This cutting system, based on geometric principles developed in the 1500's, makes use of a constant depth, linear cut to remove coal at deeper cut depths and at lower rotary speeds than a conventional rotary drum. A comparison of the linear and rotary cut paths is shown in figure 1. Approach A full-scale prototype of the linear cutting concept was valuated under laboratory conditions to determine its performance relative to standard rotary drums. Results of these evaluations show production of fewer fines, or more uniform product size, a significant reduction in the amount of airborne dust, and reduced torque and power requirements (figure 2). On the basis of these results, a contract effort was undertaken by McCracken and Associates of Bristol, TN, to design a linear cutting head for underground testing.

Jan 1, 1995

By T. G. Carnahan

The Federal Bureau of Mines investigated, on a laboratory scale, a technique for recovery of silver from pregnant solutions generated in the hydro-metallurgical treatment of complex base-metal sulfide concentrates with oxidizing chloride media. This technique provides a means for recovery and simplified reduction of accessory silver to metal from chloride solutions. The method consists of adding NaI or KI to the solution to precipitate AgI, which is then contacted with Na2S to produce Ag2S and to regenerate the iodide salt solution. Silver recoveries range from 99 pct with 20 pct excess iodide precipitant, to 92 pct when the theoretical stoichiometric amount of precipitant is employed. The Ag2S product can be reduced to silver metal by contact with aluminum chips in NaOH solution followed by purification with conventional fire refining techniques.

Jan 1, 1980

By Theodore Christos

The Bureau of Mines sponsored an investigation of the thermal oxidative degradation characteristics of certain solvents and hydraulic fluids used in underground mining operations. The following halogenated solvents were studied in view of their usefulness and their flame retardant property: tetrachloroethylene, C12C = CC12; 1, 1, 2-trichloroethane, CIH2CCHC12: and trichloroethylene, C12C = CHC1. The hydraulic fluids studied were representative of five groups approved by the Mine Safety and Health Administration for underground operation, namely: glycol-water solutions, mineral oil-water emulsions, synthetics other than phosphate esters, synthetic phosphate esters, and mixtures of phosphate esters with mineral oils and other ingredients. It was observed that the partially halogenated solvents present a greater potential toxic hazard than the fully halogenated materials, due not only to the easy production of hydrogen chloride but also to their ease of oxidation leading to the formation of phosgene and carbon monoxide. The pure phosphate esters exhibited the best thermal oxidative stability of the five groups of hydraulic fluids tested. A fluid containing phosphate esters mixed with mineral oils and other unidentified ingredients appeared to be the most hazardous On the basis that it produced very toxic acrolein and phosphine.

Jan 1, 1980

By J. Roger Loebenstein

Demand for arsenic exceeded supply in 1980, and the major domestic and foreign producers allocated available supplies to customers. Major demand was about evenly divided between industrial chemicals and agricultural chemicals. Legislation and Government Programs.-In June 1980, the Environmental Protection Agency (EPA) listed inorganic arsenic as a hazardous air pollutant.2 Proposed regulations on arsenic emissions were to be announced on an industry-by-industry basis at a future date, and public comment on the listing and on specific regulations was to be heard.

Jan 1, 1981