Search Documents

By T. A. Gray, L. M. Crayne, P. Glogowski, Trevits. M. A.

Of the 19 major mine fire events (including thermal events) that have occurred in the last 6 years (2000-2005), it is estimated that remotely constructed mine seals could have been used at 65% of the events to control or suppress the fire. Underground observations of seals that have been remotely installed during mine fire events show that they often do not fully achieve mine roof-to-floor and rib-to-rib closure. Unfortunately, the inability to reliably close the mine void has limited or precluded the regular use of this technology. The National Institute for Occupational Safety and Health is conducting full-scale underground experiments at the Lake Lynn Experimental Mine to identify and remedy existing remote sealing technology shortcomings, to develop novel technologies, and to transfer the new or improved technologies to the mining industry. This paper will discuss the remote mine seal testing program and will provide the results of the in-mine experiments. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

By R. V. Lundquist

Past reports by the Bureau of Mines have described the extraction of alumina from numerous aluminum silicate materials by the lime-soda sinter process. The results from pilot-plant investigations of six materials, with alumina-to-silica mole ratios from 0.3 to 8.7, indicated a relationship between the alumina-silica ratios and the processing characteristics of the sinter. A series of laboratory tests was conducted to define this relationship. Sinter and leach tests determined that an alumina-to-silica mole ratio of 0.90 or greater resulted in the best alumina and soda recoveries while leaving the leach slurries practically free from any tendency toward gelation. The widely different chemical and mineralogic properties of the various aluminous materials used in compounding the mixes had no perceptible effect on the leaching characteristics of the sinter. The blending of low-cost, high-alumina materials with aluminum silicate materials to give an alumina-to-silica mole ratio of 0.90 or greater would improve alumina and soda extraction and minimize operating problems in the lime-soda sinter process.

Jan 1, 1970

Reduce the time, complexity and expense of dissolving metal and mineral samples in solution in preparation for chemical analysis. Approach In earlier research, the Bureau of Mines developed a rapid and inexpensive method for the dissolution of mineral and metal samples in plastic pressure bottles heated in a boiling water bath. Using this technique, samples could be prepared for chemical analysis in less than one hour compared with several hours by traditional dissolution methods (see Technology News No. 85, December 1980 for further details). By heating in a microwave oven, sample dissolution time can be reduced to approximately 5 minutes.

Jan 1, 1983

By Steven J. Page, William A. Heitbrink, Andrew B. Cecala, Edward D. Thimons, John A. Organiscak

Miners at noncoal surface mining operations are often exposed to high levels of respirable dust. In an effort to lower the respirable dust exposure of these surface miners, the National Institute for Occupational Safety and Health (NIOSH) has been conducting research to address this problem in a practical and economically viable manner. One successful effort deals with lowering the dust exposure of equipment operators in enclosed cabs. Many types of surface mining equipment utilize enclosed cabs to protect equipment operators from dust exposure. Normally when the equipment is new, the cabs are fairly airtight. These tightly sealed cabs, combined with good filtration systems, generally provide the operator with good dust protection. However, most mining equipment is older, and as aging occurs, many components of the enclosure deteriorate. The structural integrity of the cab diminishes and the effectiveness of the air filtration system fails. NIOSH has been successfully researching costs-effective methods to improve both filtration effectiveness and cab integrity of these older cabs in order to provide a healthier work environment for equipment operators. Dust sampling records indicate that drill operators and helpers have the highest dust exposure of all workers at surface mining operations. Since much of the overburden contains a high percentage of silica, the health hazard associated with this dust can be even more serious. NIOSH research is addressing techniques to lower respirable dust levels at surface drilling operations. INTRODUCTION NIOSH's mission is to assure a safe and healthy work environment for the working men and women of this nation. The primary emphasis of NIOSH's Pittsburgh Research Laboratory (PRL) is mining health and safety research. This report focuses on two areas of research

By ROBERT R. ROUGH, FRANK L. BACON, John Dasher

(being shipped as bailast in ocean freighters). Within the last 10 years it has become more economical to use local sands, and there has been a general shift from the Belgian sand. Deposits of purer sand were treated and used for 'some time: but the suprly became limited, and means were sought to beneficiate the more bountiful subpay-f impure beach sands. These sands are composed of, 50 percent feldspar and 50 percent quartz, with small amounts of iron- bearing minerals, The most objectionable impurities in these West coast sands are the oxides of iron and aluminum. The Del Monte (Calif.) beach sand contains about 0.13 percent FeqQg and about 11.0 percent Aig03 (the latter being furnished by the large amount of feldspar present.) For the manufacture of feldspar present.) For the manufacture of flint-glass containers the maximuni quantities of these two impurities permitted in the sand are 0.05 percent F20 and 6 to 8 percent A1203.. The Fe0g occurs in the sand as follows: Traces of iron-bearing minerais resistant to weathering, ferruginous clay stains on the sand grains, and iron minerais not visible and possibly in solid solution or as colloidal incisions in the grains of feidspar or quartz. A good part of the iron in the sand is present in the traces of iron-bearing minerals, biotite, ilmenite, garnet, monazite; and hornblende. Biotite is present in larger quantities than the others. Samples of quartz, were freed of iron-bearing minerais by the use of heavy liquid (sp.gr. 2.70), leached with boiling HCI and SnCl2. Under a microscope a few apparently clean quartz grains were selected, and Fe203 was determined spectrographically to be 0.03 percent. The technique is similar to that described by Gabriel and Slavin. 4/

Dec 1, 1943

At the present time many coal preparation plants handle coal-clay wastes in one of two methods. In one method, the waste is processed in a thickener, followed by further dewatering through filtration, and subsequent blending with coarse waste refuse from the preparation plant. The resulting mixture is then disposed by stacking it in available storage locations. The coal-clay waste is often reslurried by rain or water from other sources, causing a potentially unsafe situation such as mud flows. The other method often used requires thickening and impoundment of the thickened slurry behind earthen dams which poses safety risks if structural failure of the dams occurs. To overcome these two problems, a flocculation method was developed which produces a stable agglomerated material resistant to reslurrying. How It Works The new method involves treating coal-clay waste with lime to raise the pH and flocculating the slurry with a nontoxic polymer of polyethylene oxide. The resulting floes are dewatered on a static screen and agglomerated. For extremely fine waste, further dewatering of the material is accomplished on a rotary trammel screen. The dewatered material may be ponded or mixed with coarse waste from the preparation plant to produce a stable mixture that can be stacked.

Jan 1, 1985

By Jack Wasserman, Don Wasserman, Gretchen Hinton, Logan Mullinix, Shekar Khanal

Human testing has always been a needed way to provide information on the effects of vehicle vibration, however, the manner of testing has not reflected the real situations of driver’s hands on a steering wheel and a seat with back support and driving tasks. The typical system have used a standard sinusoidal excitation rather than the typical types of road – truck excitations The new truck driver training simulators provide the combination of road roughness, speed effects, cab environment and individual tasks. The system has a full six axis simulation potential. The simulators have the protection of the individual by a combination of two ways for the individual to stop the motion as well as an operator with visual capability who can stop the testing. The closed simulator, shown in Figure 1, has the potential for providing motion during the operation.

Jan 6, 2006

By S. B. Flagg, J. F. Barkley

In the past few years an awakened activity in power-plant econ- omies has resulted in a marked improvement in the equipment for generating and utilizing steam. Although the improvement in design and construction of steam-driven prime movers has been greater than that of the steam-generating equipment, the economies obtained with the more efficient engines and turbines have stimulated interest and activity in eliminating unnecessary boiler and furnace losses. Much attention has been given to the boiler room in efforts to obtain proper combustion of the coal, because of the importance of the coal item in costs of power production. As evidence of this increasing interest may be cited the record of the development within the past few years of new apparatus for the analysis of flue gases. Many new forms of apparatus have appeared, including those for the determination of carbon dioxide, oxygen, and carbon monoxide, and others for indicating and for recording the content of carbon dioxide only, as carbon dioxide content is usually a good indicator for the control of furnace operation. Because of the large number of steam-power plants operated by the Federal Government and the number of CO, recorders used therein the Bureau of Mines undertook to collect information regard- ing the practical application of such recorders. Articles published from time to time concerning CO, recorders have been mostly descrip- tive, giving little reliable information as to the results that could be expected from the various types of instruments in ordinary prac- tice, and most of the tests made have been of a laboratory nature. Tests of several different types of recorders were made under service and laboratory conditions in order to obtain needed information. The purpose of the Bureau of Mines in publishing the results is to show the factors which may affect the accuracy of a CO, recorder and the manner in which a recorder should be tested. Readers should note that the remarks on different recorders apply to the instruments tested and not to later instruments of the same makers. In the course of the tests the following details were determined: 1. The lag in recording changes of composition of a flowing gas. 2. The accuracy of each type of recorder.

Jan 1, 1916

By L. C. IlsLey

The Bureau of Mines has collected field data and made laboratory investigations of trailing- cable performance in the hope of developing a better and safer cable for use with permissible mining machines . Because of their better insulation and performance , only rubber- sheathed cables were finally considered . The cables tested represented the product of six manufacturers . : After consideration of the results of the preliminary investigations , the conditions under which cables are used in mines , and the better performance of the later types of cables that were submitted as the investigation progressed , the bureau formulated a performance - test requirement and notified the cable manufacturers as follows : The hazards of the trailing cable are such that the bureau has been unable to extend beyond the machine its formal approval to cover the cable as at present developed . However , in the attempt to reduce the hazard as much as possible , cables passing certain tests will be recommended for this service and it is hoped that several cables will be developed to meet this requirement .

Sep 1, 1930

By Staff

The papers contained herein summarize results of various recent Bureau of Mines investigations in the area of mine power distribution systems. They are based on information from Bureau personnel, contractors and grantees, and Mining Enforcement and Safety Administration. Conclusions drawn from a series of parameter measurements on mine power systems, taken over a 3-year span, are presented. Personnel and equipment hazards due to faults on isolated, solidly grounded, and resistance grounded three-phase systems are discussed. Two papers cover dc applications of circuit breakers, including a novel protection scheme for trolley lines. The methods of suppressing induced arcing currents and voltages in a-c machines are evaluated. An evaluation program for ground monitors is described. Acceptance test procedures and the importance of various paparameters for trailing cable splice are covered. A number of techniques for locating faults in trailing cables are described.

Jan 1, 1975

Improve the safety of mine workers by developing a means of forecasting impending roof falls in underground mines. Approach The Bureau of Mines, through in-house and contract research, has developed the Roof Fall Warning Device. This battery-operated, portable electronic system forecasts roof falls by detecting and interpreting high-frequency rock noise, The technology has shown potential for detecting stress-related failures in a variety of underground environments. How It Works All geologic materials produce high-frequency acoustic emissions when they encounter an increase in stress. These ultrasonic frequency range events ( >20kHz) are well above the audible range of human hearing, very small in amplitude and duration, and can only be detected with sophisticated electronic equipment.

Jan 1, 1990

By James J. Bryja, Thomas M. Barczak, Dennis R. Dolinar, Joe Bower, Thomas P. Mucha

Maintaining ground stability in the gate roads, particularly the tailgate, has always been critical to the success of longwall mining, both in terms of safety and productivity. Several new support technologies have been developed in recent years to replace conventional wood and concrete cribbing for secondary roof support. Since their performance characteristics are unique, the best practices that have been developed with conventional wood cribbing may not be applicable for these alternative support technologies. Therefore, with so many options to consider and the importance of achieving adequate ground control at minimal cost, the trial and error approach to longwall gate road support is no longer prudent. This paper discusses a design methodology for standing secondary tailgate supports. This design technique requires in-mine measurements of tailgate support loading and convergence to establish a tailgate ground, reaction behavior based on the support and strata interaction. The methodology uses the performance characteristics generated in the National Institute of Occupational Safety and Health (MOSH) Mine Roof Simulator (MRS) to match the stiffness and load characteristics of various supports to the measured ground reaction behavior. It can be used to determine the appropriate -- application of alternative roof support systems or to design in- mine trials such that a fair and equitable comparison of different support systems can be made. A case study if the methodology at a western Pennsylvania mine site is presented in the paper, including a comparison of four alternative support technologies to conventional wood and concrete cribbing historically used at this particular mine.

By Fred N. Kissell, J. E. Matta, J. C. LaScola

The methane gas emitted from coal samples collected from the conveyor belts dumping into silos was measured by the Bureau of Mines. Approximately 50 pct of the total gas desorbed into a sealed can within 1 week was released during the first 24 hours. No simple correlation between the gassiness of the coal stored and the methane concentration in the silo open space above the coal was found. This was probably because the gassier coals were stored in open-top silos, which were better ventilated. Although the methane concentration in the open space above the coal pile was less than 1 pct for all 34 silos investigated, a methane measurement in the coal pile showed that high methane concentrations can exist. The methane released in the pile appears to accumulate and not liberate freely into the open space above the coal pile. Probably this gas is released during reclaiming operations, but further research is required to substantiate this claim.

Jan 1, 1978

By M. O. Renwick, Paul Zinner

"INTRODUCTION In September 1943, the Bureau of Mines conducted a limited program of churn drilling on the Winskell property in the Shullsburg area of Lafayette County, Wis. The work was undertaken as part of a general investigation by the Bureau of the zinc-producing area of southwestern Wisconsin at a time when special effort war being made to increase the production of metals necessary for the war program.Drilling described supplemented a previous drilling program conducted by the Vinegar Hill Zinc Co. The results of both programs encouraged subsequent investigation by the Cuba Mining Co. and eventual development of the Andrews mine.ACKNOWLEDGEMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by such project as soon as praticable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the investigative work, and prepares the final report."

Aug 1, 1947

By C. Lorimer Colburn

"High explosives are generally shipped in stout wooden boxes of convenient size, which are much sought after by miners and others for miscellaneous uses after they are emptied. The management of most mines has no fixed policy for the disposal of used dynamite boxes and will allow any one to carry them away. Many dynamite boxes are nailed up in the mine buildings or underground to serve as shelves and cupboards. Some are used as receptacles for odds and ends, and others are used in taking samples.Although used explosives containers are so generally put to beneficial service, there is nevertheless an element of danger in their use. Dynamite boxes are particularly dangerous. Very often nitroglycerin exudes from the dynamite sticks and is absorbed by the wood of the box. Such boxes are dangerous because they are very explosive. Although a box that has not absorbed nitroglycerin is safe, yet there is always the danger that a person will get a box that is partly saturated.On account of this danger, all mining companies should use extreme care in giving away used explosives containers. Some one individual who is acquainted with explosives and their peculiarities should act as inspector for every container given away. This job may best be handled by the man in charge of the powder magazines. A box that shows any stain of nitroglycerin should be destroyed by fire. The other boxes that are free from nitroglycerin or dynamite can be used."

Jun 1, 1920

By L. B. Pankratz

The Bureau of Mines determined low-and high-temperature thermodynamic properties for anhydrous ferric sulfate and anhydrous indium sulfate. Low-temperature heat capacities were measured between 50° and 298° K, and enthalpy increments above 298° K were determined. The high-temperature measurements of Fe2(S04)3 extended to 900° K and those of In2(S04)3 to about 1,000° K. A minor transition was found for Fe2(S04)3 at 800° K, with a heat of transition of 540 cal/mole. Tabulations were made of the low-temperature heat capacities and the high-temperature enthalpy and entropy increments. The 298° K entropies derived from the low-temperature measurements were 67.6±0.S ca1/deg mole for ferric sulfate and 72.2±O.5 cal/deg mole for indium sulfate. High-temperature enthalpy increments were also given in equation form.

Jan 1, 1969

Determine whether the total delay time in blasting may be safely increased beyond the currently permitted 0.5 s, without igniting a methane or methane-coal dust atmosphere and determine the minimum borehole spacing to avoid misfires. Approach At present, regulations limit the delay time used in short-delay blasting to a total of 0.5 s. Many in industry and government would like to see this total delay time increased to 1 5 to permit an increase in the number of different delays available for short delay blasting and an increase in the time between delay periods. The Bureau of Mines conducted research to determine whether the total elapsed delay time for blasting coal in underground mines could be safely expanded, with resulting improvements in productivity. The research was conducted at a surface mine in St. Clairsville, Ohio. Experimental shots were conducted in several pits, each of which had a 5-foot-high coal seam (Pitts-burg No.8) in a 50-foot highwall. The coal seam and a mobile gallery provided a good simulation of an underground coal face. The Bureau also examined the relationship between borehole spacing and misfires, to check on reports over the past few years that permissible explosives frequently misfire. These reports were not well documented, but were numerous enough to warrant investigation. Misfires of permissible explosives in an underground coal mine can be very hazardous; a burning cartridge of explosive may be ejected from a borehole and ignite the gas or dust in the mine, or a misfired cartridge in the muck pile may detonate during drilling and mucking operations, causing serious injuries.

Jan 1, 1986

By Richard J. Bielicki

The possibility of replacing the brattice cloth closest to the coal mine working face with an air curtain mounted on top of a continuous-mining machine or with a diffuser fan was explored by the Bureau of Mines. Preliminary tests conducted at a full-scale model working face with the brattice end set at 18 feet showed that the air curtain improved face ventilation only slightly and was not nearly as effective as placing the brattice at 10 feet. A 2,000-ft3/min diffuser was more effective than the air curtain. It is concluded that the air curtain probably could not function as a line brattice extension, although the diffuser fan may have some potential.

Jan 1, 1975

By Bruce K. Cantrell, Winthrop F. Watts

The U.S. Bureau of Mines and others have conducted a number of occupational exposure surveys since the publication of the International Agency for Research on Cancer report of 1989(1), which labeled diesel exhaust as a probable human carcinogen. These surveys have assessed diesel exhaust exposure using measurement of diesel aerosol and/or specific polycyclic aromatic hydrocarbons as indicators of exposure. This report reviews, available diesel exhaust aerosol and gas measurement techniques. Measurement of human exposure to toxic agents is the first step in determining the exposure-dose-response relationship. It is a fundamental step in risk assessment. Measuring exposure to diesel exhaust pollutants is particularly challenging due to the complexity and variability of exhaust components. This paper reviews current occupational health standards for diesel emissions and available diesel exhaust gas and aerosol measurement techniques. Although surveys in mines have primarily assessed diesel exhaust exposure using diesel particulate matter (DPM) some exhaust gas measurements have been used as indicators of exposure. DPM is emphasized because it is a major component of diesel exhaust, is suspected to make a major contribution to the health hazard, and is measurable. OCCUPATIONAL HEALTH STANDARDS Occupational exposure surveys of diesel exhaust frequently measure regulated pollutants, or pollutants that are suspected carcinogens, even if no permissible exposure limits (PELs) have been established. In the United States, various organizations recommend a range of allowable values for diesel exhaust gaseous constituents, including carbon monoxide (CO), carbon dioxide (CO2), sulfur dioxide (SO.), nitrogen dioxide (NO2), nitric oxide (NO), and formaldehyde (HCHO). Table I summarizes these recommended levels, showing 8-hour or 10-hour time-weighted-average values where available; where these are not available, 15-minute short-term [ ]

By John W. Buch

"INTRODUCTION The Ruhr coal basin is estimated to cover an area of more than 1,000 square miles. Here, the total thickness of the coal bearing formation (Carboniferous) is 10,500 feet, and drilling-hole have revealed 92 coal beds with a total thickness of 262 feet. 6/ Beds pitch from 0 to 90 degrees and about 70 percent of the wartime production came from beds that pitched less than 30 decrees. 5/For example at the Minisiter Stein mine, there are 24 minable coal beds ranging from 80 centimeters. (2 ft., 7 1/2 in.) to 250 centimeters (8 2 1/2 in.). The vertical thickness of the measures is 1,000 meters (3,200 ft.), and at this mine the deposits are covered with 150 meters (500 ft.) of surface wash. The cross section (fig, 1) at Fritz mine; Hoesch, A.G., Essen, Ruhr, is characteristic, The mines have been developed and worked to vertical depths of 2,000 to 2,500 feet by vertical shafts; main-level intervals are 500 to 700 feet apart. Haulage roads are straight, driven in rock, and centered as nearly as practical between property boundaries. Levels are sectionalized by driving crosscuts at right angles to the main haulage road on 800- to 900-foot centers. The roads are the main transportation arteries for the use of trolley or Diesel locomotives. A plan of the sixth main level (fig. 2) at the Bruchstrasse mine; Gelsenkirchener A.G., Bochum, illustrates main-level development and,sectionalizing with crosscuts. The cross section in figure 3 is that of the fourth crosscut west at the same mine."

Oct 1, 1946