Search Documents

By Timothy J. Rohrbacher

This report presents a U.S. Bureau of Mines study that incorporates coal mining factors, coal recovery factors, and economic factors into the definition of an economically recoverable coal resource. The relationship between these factors to the Energy Information Administration's estimate of U.S. coal resources-the "Demonstrated Reserve Base"-is discussed. The Matewan 7-1/2 minute quadrangle in eastern Kentucky was selected as the initial study area. Results indicate that of the original 1,193 million tons of resource in the quadrangle, only 89 million tons (7.5%) are economically recoverable at a cost of $25 per ton or less. At the current production rate of 5.3 million tons per year, this represents only 16.8 years of remaining reserves.

Jan 1, 1993

By Richard E. Hucko

The bureau of Mines conducted a laboratory scale investigation of the process of selective flocculation with the objective of developing a method to effect separations on suspensions consisting predominately of ultra-fine-size (minus 400-mesh) particles of coal and refuse. Selective flocculation of coal from coal-refuse slurries could be achieved with a wide variety of reagents. Typically as much as 15 to 20 weight-percent of high-ash solids (70 to 80 percent ash) could be retained in suspension. The flocculated sediment remained a high-ash product, however, and would require further treatment to be regarded as clean coal. No combination of reagents and conditions led to selective flocculation of the refuse component. The dispersing agent was found to be the critical factor; dosages of 3 to 8 lb/ton2 were necessary to stabilize the suspension for subsequent selective flocculation. In addition, most of the dispersants that worked were most effective at substantially elevated pH (11 or so). It was concluded that this process would be prohibitively expensive and, because of yield and quality constraints, it would be of questionable utility in today's coal preparation industry.

Jan 1, 1977

Provide reasonably priced, reliable fire protection for blasthole drills. Approach An automatic fire sensing and suppression system using both dry and gaseous chemicals was developed, and is more shock and vibration resistant than similar industrial fire protection systems. How It Works Temperature sensors mounted in the drill's machinery house, hydraulic room, operator cab, and transformer area detect the heat from a fire, and trigger a sequence of actions. The same fire fighting sequence can be initiated from manual alarm boxes in the cab, hydraulic room, or machinery house. Electrical power to the drill Is immediately cut off, and a horn sounds to warn the drilling crew. After a 40-second, built-in, delay to allow time for drill's ventilating fan to stop, gaseous and dry chemical fire extinguishing agents are piped to and released in various rooms of the drill. The gaseous extinguishing agent (Halon 1301) is released in the machinery house, hydraulic room, and operator cab where dry chemical clean-up from electrical panels and machinery would be difficult and costly. Dry chemical is piped to the transformer room at the rear of the machine. Location of the principal components of the system are shown in the drawing.

Jan 1, 1979

Develop rugged, cost-effective fire protection for hydraulic shovels and backhoes. Approach Automatic fire sensing and suppression systems were designed and built for use on hydraulic shovels and backhoes. How It Works A line-type temperature sensor is mounted in the machine's engine and hydraulic pump areas to detect the heat from a fire while it is still small and easy to control. Two systems were tested. In one, the inside of the sensor consists of two conductors separated by a ceramic material whose electrical resistance decreases with increases in temperature. When heated to a predetermined temperature) the control circuit responds to the resistance drop. In the second system, the detection element of the sensor is comprised of a thin metal tube containing a hydrogen charged metal hydride wire. The tube is sealed at one end and is connected to a sensitive pressure switch at the other end. When exposed to the heat from a fire, hydrogen gas released from the metal hydride wire actuates the pressure switch.

Jan 1, 1980

By Linda L. Chasko, Charles P. Lazzara, Ronald S. (deceased) Conti, William J. Wiehagen

Fire has long been a concern for underground mine workers. A mine fire can occur at any time and can result in a partial or total evacuation of mine personnel and the loss of lives. Fires can grow rapidly. Time is the critical element. Prompt detection, timely and accurate warnings to those potentially affected, and a proficient response by underground miners can have a tremendous impact on the social and economic consequence of a small underground fire. Fire preparedness and response have components of technology and people. These components can work synergistically to reduce the time it takes to bring the system back in balance. This report deals with the preparedness of miners to respond to underground mine fires. It is intended to aid the mining industry in understanding the various roles of emergency responders and the training techniques used to increase their skill levels. The report also presents a technology overview to assist in effective response to mine fires.

Jan 12, 2005

By Oliver Bowles

Wire saws have been used for many years in European travertine, marble, and slate quarries. This method of sawing found very limited use in America until 1927 when it was accepted as standard equipment in elate quarries in Pennsylvania where it has been remarkably successful. Details of its operation in slate have been published in a recent bureau report.3 The very limited extent to which the wire saw has been employed in limestone and marble quarries in the United States and the seeming lack of interest even in experimental work to determine its advantages are difficult to explain in vied of its wide use in cutting similar rocks in Europe and its unquestionable advantages in sewing slate in America. In order to encourage improvement in quarry practice the United States Bureau of Mines has endeavored to obtain information as to the extent to which wire saws are used in Europe together with data on the rate and cost of sawing. The information at hand is by no means complete either in territory covered or in details of operation; it nevertheless brings out certain significant features that may be of interest and advantage to quarrymen in the United States.

Jan 1, 1931

By J. W. Thompson

ORE CONCENTRATION PROCESS-PATENT OIL FLOTATION PROCESS. The invention of the patent issued to Sullman, Picard & Ballot November 6, 1906 (United States Letters Patent No. 835120), is based upon the discovery of an wholly unexplained phenomenon arising from the agitation of ore pulp containing oil and air in certain proportions. This was a discovery in an art in which it was well known that the elements of oil, air, and agitation possessed certain characteristics and produced certain results. As early as 1860 a British patent first suggested the use of oil in water concentration of ores by pointing out the affinity which oils have for metallic sub- stances in preference to gangue. Subsequently many patentees employed the known affinity of oil for metal in ore concentration proc- esses by using oil in proportions varying from 2 per cent to 300 per cent of the ore and recovering the oil-coated metal particles by causing them to rise to the top or sink to the bottom of the pulp. In these processes the agitation was either gentle or thorough but never great, and though always employed to produce thorough oiling of the metal it was used in different degrees for the sole pur- pose of causing the metal particles to rise or sink. In the prior art the oil was used for its known selective affinity for metal, agitation was em- ployed to mix the oil with the metal, and air was introduced to supple- ment the buoyancy of oil in raising oil-coated metal particles to the surface. To this extent had the art of oil flotation advanced when the patentee entered it, having reached the commercial stage in only two processes, representing respectively metal-flotation and metal-sinking processes, and having reached the stage of success in none. In the line of experiments by the patentee when the proportion of oil to ore was reduced to 1.5 per cent a "float" appeared; at 1.04 per cent still more "float" appeared; at 0.32 per cent the "float" again vastly in- creased; at 0.1 per cent the "float" again vastly increased. It thus developed that in using oil at 0.1 per cent or even at 0.05 per cent of the ore and after violently agitating the pulp from 24 to 10 minutes, there arose to the surface when the pulp was brought to rest, a thick froth or foam of oil-coated air bubbles carrying oil-coated metal particles to the extent of about 90 per cent of the metal con- tent, the foam being sufficiently stable to permit removal and metal recoveries. This was a new result based upon phenomenon then unknown and still unexplained and constituted discovery and promised a change in the art of oil flotation from laboratory experi- ments and mill failures to commercial success. The patent referred to covering the points mentioned has been sustained by the District and the Circuit Courts of Appeals and by the Supreme Court. Miami Copper Co. v. Mineral Separation, 244 Federal, 752, pp. 754-757. ORE CONCENTRATION PROCESS-OIL FLOTATION-INFRINGEMENT. The Miami Copper Co. in its process of concentrating ores by the oil flotation process used three distinct processes that were either the processes included and covered by the Sullman, Picard & Ballot patent or their fair equivalent and which were clearly an infringe- ment of the patent, and the company can not escape liability for such infringement by taking an additional step, although such additional step if taken alone would not constitute an infringement of the Sullman, Picard & Ballot patent. Miami Copper Co. v. Mineral Separation, 244 Federal, 752, p. 768. ORE CONCENTRATION PROCESS-VALIDITY OF GREENWAY PATENT. The patent issued to H. Greenway, June 9, 1914 (Letters Patent No. 1999699), is valid. The process disclosed in this patent was a substantial departure from processes of the prior art. The heating of water is a matter of large moment and the use of acids is a matter of constant and considerable expense. By wholly dispensing with both by the use of a minute quantity of hydroxy compounds, the patentee has disclosed an original and novel plan which has broad- ened and made more simple the agitation process of air flotation. The novelty and inventive character of Greenway's discovery is patentable.

Jan 1, 1918

By H. P. Rue

For the proper control of gasoline treating plants there is need of a quick test for corrosion. In "sweetening" gasoline that is, in treating it to remove evil smelling mercaptans or to convert them to disulphides or sulphides the sodium plumbite ("doctor") method is generally used. This method involves agitation of the gasoline with "doctor solution's (sodium plumbite made by dissolving litharge in a solution of caustic soda) in the presence of free sulphur3. One of the common mistakes in the technique of this process is the addition of too much free sulphur, which will dissolve in the gasoline and cause it to be corrosive. In the operation of a continuous sweetening; or treating plant, a check on the corrosiveness of they product is imperative at all times. The copper-strip test commonly used in specifications take, so long to perform that the plant may fail to function properly for some time before the operator discovers it. The writer has investigated a rapid corrosion test method involving the use of metallic mercury, recently developed by Messrs. G. T. Granger, refinery superintendent, and A. B. Comstock, chief chemist, of the Barnsdall Refineries, Inc., Okmulgee, Okla. They have used this test successfully for several months in controlling the operation of their continuous treaters any have come to the conclusion that it has several advantages over the copper-strip test. Chief among these is the time caved, as the copper-strip test takes at least one-half hour, while the mercury test can be wade in about five minutes. It is very evident that this is an important item in controlling a continuous treater.

Jan 1, 1928

By John C. Machisak

THIS CHAPTER reports employment data and injury experience in the metal, nonmetal, quarrying, sand and gravel, and slag (iron blast furnace) industries of the United States in 1959. Each industry is treated separately, and no attempt has been made to combine data to show an overall total for this group of mineral industries. The slag canvass is included for the first time (data on employment and injuries were not collected before 1958), and, like other canvasses included in this chapter, data are voluntary. Employment and injury experience for all mineral industries can be found in volume III. The employment and injury information in this chapter came from reports submitted to the Bureau of Mines before May 31, 1960; therefore, figures are preliminary and subject to revision. Voluntary reports submitted by operators have contributed substantially to safety promotion since 1911, when the Federal Bureau of Mines started collecting employment and injury facts.

Jan 1, 1960

By L. C. IlsLey

In the normal operation of mines, the aggregate effect of many seemingly minor op rations may be very important as respects economy and safety. Anion: these operations is the method employed in coupling and uncoupling mine cars. For economic reasons the equipment in mines has not been protected as well as railroad equipment. It is pertinent that haulage accidents rank second in severity among mine accidents, and that manual coupling of cars has been one of the most frequent causes of such accidents. One study4/ revealed that coupling was responsible for about 20 percent of haulage accidents underground. A review of early conditions on steam railroads, which were responsible for the introduction of safer methods of coupling cars, indicates how conditions in might be improved. THE STORY OF RAILROAD COUPLING As any considerable improvement in mine-car coupling probably will follow lines somewhat similar to those that brought order out of chaos for the railroads, it seems appropriate to review briefly the steps taken to improve railroad coupling from the days of link and pin couplings of various types to the adoption of the standard ?M.C.E? automatic coupler.

Jan 1, 1943

The following methods should be used to protect miners from the adverse health effects of exposure to respirable coal mine dust and respirable crystalline silica: ? Informing workers about hazards ? Establishing written emergency procedures ? Using engineering controls, work practices, and personal protective equipment (including respiratory protection when dust control equipment is being installed, maintained, or repaired) ? Monitoring exposures ? Conducting medical screening and surveillance ? Encouraging smoking cessation ? Maintaining medical records

Jan 1, 1997

By Jr. Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.

By Richard V. Ageton

"Everyone admits that there are more accidents in metal mines than there should be but there is much difference of opinion as to the causes of accidents, whether avoidable or unavoidable, and the amount of responsibility attaching to the miner and the mine operator, respectively. However, it seems that one of the main reasons why there are so many accidents, is that there is so little general knowledge regarding their causes and costs. Some information regarding the costs and causes of metal-mine accidents is presented in this paper.The data contained were obtained from a study of the complete accident and medical reports of two large metal-mining companies, which carry their own insurance. Path maintain hospitals with competent medical attendants. One of these companies also maintains a very efficient safety bureau, consisting of a safety engineer, with two assistants who work in connection with the medical department, and with the safety committee made up from among the miners themselves.Daring the year of 1920, ""A"" Company employed approximately 900 men, and these men worked more than 270,000 shifts. There were 373 minor and major injuries, among these 900 men, hence assuming that each injured man was hurt cut once, 41 per cent of the men who worked in this mine received some kind of time-losing injury during the year. On account of these injuries the injured men lost 3731 shifts, and thus the time lost due to injuries amounted to approximately 1.4 per cent of the total number of shifts worked,"

Oct 1, 1923

By James E. Mills

Coal, in the process of mining, transportation, and handling and on exposure to the weather, is subject to more or less disintegration. This disintegrated coal is usually called "slack" and amounts often to a considerable percentage of the lump coal produced in the mines. If this slack coal is wasted the loss so occasioned ranges from 5 to 50 per cent, or even more, of the total coal mined. It is therefore clear that the utilization of this waste slack coal becomes a serious economic consideration. When the coal is suitable for the production of coke, the utilization of the slack presents no difficulty, as it is in demand for that purpose. If the coal does not produce good coke, but cakes rather readily, the slack can be used for boiler purposes, as it fuses together more or less quickly, and burns on the furnace grate without great loss. Coal that cakes less readily can be burned on grates of special construc- tion. When so used it is more troublesome to handle, and the waste is greater than when lump coal is used. Consequently the price of much of the slack coal for fuel purposes ranges considerably lower than that of the lump coal from the same mine. The full value of this slack coal as fuel can be realized by first form- ing the coal into a coherent mass or briquet, such briquets, when of good quality, being equal to or of greater value than the original

Jan 1, 1911

By Stephen L. Tillim

Tubular Handles can negatively affect the contents of the carpal tunnel. Years of injuries from grasping handles for tools and machines can cause carpal tunnel syndrome, tendonitis and wrist joint injuries. The can cause inability to use a hand and resulted in the longer absences from work than injuries from falls, accidents or fires.1 Cylindrical, tubular and rectangular handles are rolled flat structures. They place the hand on a rolled flat surface where the ends of the middle and ring fingers overlap the index and small fingers. They are pulled along a series of lines that contact the end joint of the index finger, the middle bones of the middle and ring fingers and the end bone of the small finger. Cylinders are pulled diagonally in the hand toward the carpal tunnel (CT) area. Gripping in this manner tenses asymmetric muscle groups in the forearm. Handles could work better if they do not place pressure on the CT and conform to the natural function or neutral hand position where the hand rests or dangles at the side of the body, the finger tips form a diagonal, the palm and fingers form a cup, the thumb rests between the index and middle fingers and the wrist is mildly extended. However, handles designed for the neutral position are pulled by diagonally oriented fingers into the valley between the thenar and hypothenar muscles where they can compress the median nerve and tendons exiting the CT. Seven principles for handles that do not place pressure on the carpal tunnel and employ optimal hand position are presented. First, handles should align the ends of the fingers parallel to the horizontal crease and not diagonally. Second, handles should extend from the cupped fingers to meet the muscles at the base of the thumb on the radial side of the hand and extend further on the other or ulnar side to meet a portion of the small muscles. Third, handles should have a recess on the proximal side to prevent contacting or placing pressure on the carpal tunnel. Fourth, handle design should be based on hand measurements in a position of function. Fifth, handles should come in sizes. Sixth, handles should be placed on tools to maintain the wrist and elbow in neutral position. The seventh is handles should support the maximum area of the hand and absorb, but not direct, vibration to the carpal tunnel. These principles led to prototypes and patents for handles for gripping, pinching and squeezing2,3,4 . The poster will illustrate and explain the principles Bonsil handles. Research, with existing tools, is needed to substantiate claims made for the Bonsil handle.

Jan 6, 2006

By Michael A. Trevits

Mine fires can be especially perilous because toxic products can quickly spread well beyond the fire zone thereby exposing all underground miners to dangerous and deadly conditions. Since November 1998, there have been six major underground coal mine fires or explosions in the United States (Willow Creek (twice), Sanborn Creek, Loveridge No. 22, West Elk and the Jim Walter Resources No. 5 Mine). In each case, the entire mine or specific areas of the mine had to be sealed due to the build-up of dangerous gases and the fear of uncontrolled spread of the fire. Effective placement of mine seals can deprive a mine fire of oxygen and is often followed by water flooding or injection of inert gas into the affected area. When access to the fire zone is impossible because of safety reasons, airtight mine seals can be constructed, in the area of the fire, remotely from the surface through vertical boreholes. Remotely constructed mine seals are commonly made from cementitious material. Since these mine seals are typically erected blindly, it is difficult to determine if mine roof-to-floor and rib-to-rib closure has been obtained. This paper provides a review of the available materials and technology used to remotely construct mine seals through vertical boreholes.

Jan 1, 2002

By G. S. Rice, H. P. Greenwald

"Experience and experiment have goth shown that a cloud of coal-dust in air can be inflamed and an explosion developed only when a certain minimum concentration of the dust in air has been equaled or exceeded. Those who have had experience in the handling of coal know that dust is frequently present in the air and may be of sufficient density to obscure an ordinary electric light at a distance of 40 or 50 feet; yet flames may be, and times without number have been, introduced into such clouds, when no additional coal-dust has been stirred up, with no effect other than the burning of the dust particles which actually enter flame. Evidently the density of the dust cloud is insufficient to give self-supporting combustion.The minimum amount of dust in air required to give a spreading flame will vary with a number of factors such as the composition of the dust and its size. This amount in a unit space may be considered analogous to the lower limit of inflammability of fire damp (methane) in air, although the variation in limit of explosibility of gas is small even when conditions of the experiment are altered. In large-scale determinations of the lower limit of inflammability of coal-dust there is no certain method by which a sample of the dust cloud can be snatched and its density determined. It is necessary to produce the best possible dust cloud from a known weight of dust, in a known volume and assume - probably with considerable error - that the dust cloud is reasonably uniform. The dust cloud must be formed and the source of ignition applied to it simultaneously; this is generally accomplished by the use of blow-out shots of black blasting powder, dynamite, or similar explosive so prepared as to blow out like a cannon shot, or by a gas explosion. The more violence attending the source of ignition, the greater is the probability that all the dust is raised in a uniform cloud; and the greater the length or intensity of the flame, the greater are the chances of ignition. As a result one may obtain a variation in apparent minimum density with different sources of ignition. This difference is more apparent than real and must remain until devices for instantaneous sampling of dust clouds during explosions are perfected."

Aug 1, 1931

By David F. Gearhart, Thomas M. Barczak

This U.S. Bureau of Mines report examines the roof and floor contact pressure provided by the interaction of a shield with the surrounding strata. Controlled forces were applied to an 800-ton two-leg shield in the Bureau's mine roof simulator; the distribution of forces acting on the canopy and base of the shield were measured with 24 hydraulic pressure cells. Several influential factors that affect the load distribution were investigated: (1) the magnitude of loading (leg pressure); (2) the profile of the canopy, principally the upward-sloping tip; (3) the base-lifting device; (4) horizontal load acting on the shield; and (9 compliancy of the immediate roof and floor. It was concluded that the shield does not develop full canopy or base contact without deformation of the strata. Maximum contact pressures are developed at the rear of the canopy and on the toes of the base. Less than 10 pct of the available shield capacity is developed at the canopy tip despite the design intention to ensure tip contact. Horizontal loading reduced the toe pressure acting on the base by as much as 75 pct. The base-lifting device exaggerated the inherently high toe loading, increasing the contact pressure by more than 200 pct.

Jan 1, 1992

By Alla D. Mah

No experimental heat-of-formation value has been reported in the literature for cerium sesquioxide. The heat of formation of bismuth sesquioxide has not been determined in recent years, and the older value was subject to large uncertainty. Accordingly, the heats of combustion of cerium sesquioxide and bismuth metal were measured by the Federal Bureau of Mines. The heats of formation were: ?H°298.15 = -427.01 ± 0.70 kcal. /mole for cerium sesquioxide and ?H°298.15 = -137.16 ± 0.30 kcal./mole for bismuth sesquioxide. The free energy of formation was estimated for cerium sesquioxide and accurately calculated for bismuth sesquioxide. The data were compared with values in the literature.

Jan 1, 1961

By D. Dolinar, T. P. Mucho

Horizontal stresses are caused by global plate-tectonic forces. During 1995 alone they were largely responsible for the closing of two longwall mines in the United States. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky and Alabama. In each case, a mine encountered roof falls or difficult ground conditions at the headgate caused by horizontal-stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble free. The paper also discusses detailed measurements that were made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal-stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel to the maximum horizontal stress, as previously thought, but rather it is 20° in the stress shadow of the gob. Other stress-control techniques, including artificial support, are briefly discussed.