Search Documents

By R. P. Jewett

The object of this investigation was to correlate the crushing strength of green pellets prepared from magnetite, specular and earthy hematite with the particle size of these respective raw materials. In this study no attempt was made to correlate the strength of fired pellets and particle size. The effect of particle size upon a number of fine ores and concentrates was studied. Much of the low-grade ore reserves in the Lake Superior Region must be finely ground before concentration and then agglomerated for iron and steelmaking processes. Fine natural ores also must be agglomerated. Pellets constitute an important type of agglomerate. Considerable handling occurs during screening to remove undersize and oversize pellets, and in transfering green unfired pellets from the balling machines to the heat-hardening equipment. As a result the strength of the green pellets is a factor of great importance.

Jan 1, 1961

By R. Barany

The heat of formation at 298.15 ° K of muscovite was determined by solution calorimetry . The value obtained for the heat of formation from the elements was -1,421.2 ± 1.3 kcal / mole , and the value for the heat of formation from the oxides was -55.9 ± 1.3 kcal /mole .

Jan 1, 1964

By R. J. SHAW

Oil shale has been defined as, "a compact, laminated rock of sedimentary origin yielding over 35 percent of ash and containing organic matter that yields oil when distilled but not appreciably when extracted with the ordinary solvents for petroleum." The oil-yielding organic matter in oil shale, commonly called kerogen, decomposes upon application of heat to form bituminous materials that are soluble in organic solvents and may be extracted from the inorganic residue. However, separation usually is accomplished by continuing the heating and thereby cracking the primary bitumens to gas and oil, which distill, leaving a carbonaceous material on the mineral residue. It has been suggested that this conversion takes place only at relatively high temperatures - 750°F or higher. On the other hand, other workers have found that transformation may take place to some extent at temperatures as low as 400°F. In either a solvent extraction or a destructive distillation process for separating organic material from the inorganic portion of oil shale, the quantity of heat required to raise the temperature of the oil shale sufficiently to induce a satisfactory rate of conversion of kerogen to oil is important in determining the design of an economical process. Likewise, the quantity of heat recoverable from a spent shale is important in determining the overall heat balance of the process. Published data on the specific heat of American oil shales are meager. Gavin and Sharp present data for two samples of Colorado oil shale, one from near DeBeque and one from Parachute Creek, and for a sample of spent shale over a temperature range of 68°F to 1940°F. McKee and Lydor present data on the specific heat of two samples of oil shale from near DeBeque, Colorado. Additional thermal data on various grades of oil shale over a wider range of temperature are needed in order to apply sound engineering practices to the design of equipment for processing oil shale.

Nov 1, 1947

By Walter D. Holland

LFE Environmental performed an Industrial Hygiene survey of the Paraho Oil Shale Mining and Processing facility in Anvil Points near Rifle, Colorado, on August 6 and 7, 1975. This survey consisted of an investigation of the underground operations for diesel emission contaminants and of the above ground work areas for all inhalation contaminants other than silica dust. Samples were collected to investigate the following contaminants: respirable dust, total dust, NO2, NO, H2SO4, formaldehyde, CO2, S02 and CO. None of the determinations of contaminants in the underground operations indicate air concentrations exceeding their standards. The results for the samples collected above ground indicate only one operation where the employee's exposure exceeds the standards. It is a welding operation where the standards for total dust and lead are exceeded. Since the survey the employer has installed an exhaust ventilation system which has significantly reduced the welder's exposure.

Jan 1, 1976

By E. J. Gleim

In April 1932, the Bureau of Mines published Information Circular 6595, entitled "Data in Reference to Installation of Cables in Shafts and Boreholes", in which were described methods followed in various sections of the United States when electrical circuits are taken into mines by means of cables suspended in shafts and boreholes. In view of the present tendency to extend high-tension cables along entries and passageways from the bottom of the shaft, borehole, or other point of entrance to coal mines rather than over the surface, it is deemed that the various methods of installing such cables deserve careful consideration, particularly in mines in which gas and coal dust contribute to explosion hazards. This is especially true of localities where there is an inclination to restrict the extension of 2,300- and 4,000-volt circuits into the mines. Probably it is feared that accidental contact with the cables of such circuits may result in more serious shock than with lower voltages; also, it is possible that new circuits are regarded merely as explosion hazards additional to those already existing, regardless of the manner in which the new circuits may be installed. It is the firm belief of some engineers that the circuits can be installed so that they will not be damaged by wrecks or roof falls, thereby eliminating the hazard of explosion from this source while at the same time making the chance of accidental contact remote if not impossible. Moreover, some believe that fire hazards from direct-current systems can be reduced by keeping motor-generator sets close to load centers. Thus, although the alternating-current circuits would be lengthened, the size and extent of direct-current circuits would be kept to a minimum.

Jan 1, 1939

By William A. Beck

"The Piedmont Manganese Belt extends from Taliferro County, Georgia, 70 miles in a northeasterly direction through Greenwood County, South Carolina, and conforms with the trend of the Piedmont Province. The total area of the belt is reported to be about 1,000 square miles, and the maximum-width is about 24 miles.Manganese has been known to exist in the belt since 1845. M. Tuomey mentioned a deposit in the Edgefield district on Hard Labor Creek in South Carolina in a report on the geology of South Carolina published in 1848.Ore was first mined about the time of the first World War, when the Colley mine, near Lincolnton, Ga., was. Opened. The only operation in the area at present is that of the Abernathy & Kehaya Mining Co., at McCormick, S. C.The geographical position of the belt is from west longitude 82° 57’, north latitude 33° 39' to west longitude 82° 06', north latitude 34° 08'. The towns of Washington and Lincolnton, Ga., and McCormick and Greenwood, S. C., are in or near the belt.An exploratory project of the Bureau of Mines was started on the McCormick, S. C., deposit in April 1944, and trenching, test pitting, and hand-auger drilling-were done on a small scale until early in October 1944. (Fig. 1.) In November 1944 work was begun on a property 12 miles north of McCormick, known as Parsons Mountain, which is leased to M. H. McKnight by the United States Forest Service. From March 15 to March 24, 1945, work was done on the property of Mrs. H. B. Ross, which is known as the Morgan farm.The Abernathy & Kehaya manganese mine contains what is locally known as the Dorn gold mine; mineral rights on the property were owned by M. G. & J. J. Dorn, Inc."

Apr 1, 1946

1. Data from the Mine Safety and Health Administration (MSHA) indicate that a total of 241,502 employees worked in surface mining locations in 2003, corresponding to 212,113 full-time equivalent (FTE) workers. • Surface employees accounted for 84.6% of all mining employees. • The majority of surface employees (73.7%; n = 177,927) were mine operator employees as opposed to contractor employees. • Stone operator employees comprised the greatest percentage (27.2%; n = 65,743) of surface employees.

Feb 1, 2005

By Mark S. Sanders

The purpose of this work was to develop and field test improved knee protection for underground coal miners working in low seam mines. In a previous phase of this contract (Sanders, 1982), experimental knee pads were developed and field tested. The field test revealed several design deficiencies with the knee pads, and suggestions for improving the design were made. The work summarized in this report, therefore, consists of modifying the design and method of fabrication of the knee pads originally describes by Sanders (1982), and of field testing the improved design. The new prototype was shorter and wider than the original design, and used a neoprene pass-through strap design rather than a cloth strap molded into the pad itself. The new prototype was constructed by slush molding a hollow bladder that was then filled with foam. Initial reactions to the pads in the field test were very positive. However, after two months, the opinions about the new prototype became less positive. They were judged, generally, to be no better or worse than the pads usually worn by the field-test participants. Problems were encountered in the field with respect to durability. Water seeped into the inner cavity of many of the pads and caused the foam to deteriorate. It was concluded that it would not be cost-effective or feasible to significantly improve upon current commercially available knee pad designs.

Jan 1, 1986

By J. D. Spagnola

The Bureau of Mines conducted research to obtain comparative data on the extent of reduction of galena and sphalerite with molecular hydrogen and with hydrogen from the thermal cracking of ammonia and methane at various time intervals. Galena reductions of 95 to 99 percent were obtained with H2 and with decomposed NH3 while reductions of 70 to 80 percent were obtained with cracked CH4? Sphalerite reductions of 99 percent were obtained at 1,000° C with Hz and with decomposed NBs; however, complete volatilization of the free zinc from the remaining concentrate and the subsequent recombination of zinc and sulfur vapors resulted. A promoted iron catalyst brought about a decrease of 100° C in the temperature required for complete decomposition of ammonia. It was found that H2S retards NB3 decomposition and that nitrogen retards the reduction of galena by H2? A mixture of N2 and He in about the same ratio as that obtained by the thermal cracking of NBs gave about 15 percent less reduction of galena than was obtained with decomposed NB3; this indicates that a portion of the hydrogen obtained by NBs decomposition is in an active form.

Jan 1, 1965

By A. H. Warner, G. A. Morrison

"INTRODUCTION The brown-iron ores of the Western Highland Rim of Tennessee extend north and south across the State for 115 miles. Many prospects of iron ore are known in this area.The district is credited with an output of 8 million tons of washed ore prior to 1930. Records on past shipments of ore indicates that the grade was probably 45 to 50 percent iron, 0,7 to 1.25 percent phosphorus, and 10 to 21 percent insoluble.As part of a survey of the iron resources of the Appalachian area, the Bureau of Manes began exploration .of the Churchwell and Robinette properties April 16, 1945, and continued until July 25, 1945, during which time 122 feet of test pits were sunk and 667 feet of churn drilling was completedPROPERTY AND ACCESSThe Churchweil property and that part of the Robinette tract north of U. S. Highway 64 are reported to be owned by the heirs of William Millsaps.The Churchwell property is northeast of Waynesboro, the county seat of Wayne County (fig. 1), and is east of Forty-Eight Creek, between Duggar Branch on the north and Little Forty-Eight Creek on the south.The property is reached from Waynesboro by traveling U. S. Highway 64 east 8 miles to Forty-Eight Creek, thence north on a secondary road 2 miles, to where Little Forty-Eight Creek joins it, thence by an old logging road up the hill half a mile to the property.The Robinett tract lies 1 mile southeast of the Churchwell and is reached by traveling east from Waynesboro on U. S. Highway 64 and a distance of 6.7 miles, and then turning left on an old logging road and following the ridge 2 miles to the prospect."

Oct 1, 1946

By Oliver Bowles

"A Product from Mica Mines.Mica commonly occurs in pegmatites which consist of large crystals of feldspar and quartz, mica constituting but a small proportion of the total rockMuch of the feldspar thus thro n out during the process of mining is pure and of high quality, end the Bureau of Mines has suggested that much of it could be utilized for ceramic purposes. Encouragement is given to such utilization by the fact that several mines now worked for mica were formerly operated for the production of feldspar. ""'here mines are not readily accessible to railroads feldspar utilization might not be feasible, for it is a much lower priced product than mica and cannot therefore bear as heavy transportation expense. '""here mines ire located close to railroads, however, such utilization would tend to reduce the cost of mica mining, and at the same time assist in the solution of the waste disposal problem.The Bureau has recently been informed that some of the feldspar from mica mines near Spruce Pine, N.C., is now being sold and shipped away. An extension of this by-product industry is to be recommended.A Mica Deposit in New York City.The Bureau recently received a mica specimen obtained from a. building excavation at 157th St. and Riverside Drive, New York City. The specimen was about 2 by 4 inches in size, and fairly clear though containing numerous hair cracks. It was obtained only 7 or 8 feet below street level. At greater depth and with more careful methods of excavation material of much better quality might be obtained. The material submitted could be used for mica washers but not for sheet mica. It is stated by an official of a prominent mica company that many such fragments are obtainable in this locality and the possibility of the occurrence of a good mica vein is thereby suggested."

Jun 1, 1920

By John J. Sammarco, Janet S. Flynt

This report (Independent Functional Safety Assessment Guidance 7.0) is the last in a nine-part series of recommendations and guidance addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and after-market suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction (Part 1).—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety (Part 2) and 2.2 Software Safety (Part 3).—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g]and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File (Part 4).—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment (Part 5).—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. The guidance reports comprise parts 6 through 9 of the series and are listed below: [< 5.1 System Safety Guidance (Part 6).—This guidance supplements 2.1 System Safety. < 5.2 Software Safety Guidance (Part 7).—This guidance supplements 2.2 Software Safety. < 6.0 Safety File Guidance (Part 8).—This guidance supplements 3.0 Safety File. < 7.0 Independent Functional Safety Assessment Guidance (Part 9).—This guidance supplements 4.0 Independent Functional Safety Assessment.] [ ]

Jan 4, 2006

By Martin H. Stanczyk

Acid leaching of selected copper sulfide minerals, impure copper sulfide flotation concentrates, and a cement copper precipitate at elevated temperatures and pressures was investigated. Copper extractions of 97 to 99 pct were obtained by leaching chalcopyrite and the flotation concentrates with water under oxidizing conditions at 200° C for 30 to 60 min. In tests with bornite, chalcocite,and cement copper, addition of sulfuric acid or pyrite to the autoclave was required to obtain similar copper extractions. The chemistry of leaching copper minerals was studied. It was determined that different copper sulfides altered to covellite as one step in their dissolution.

Jan 1, 1963

By Spencee L. Willett

In 1986, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied a 51, 160-acre portion of the 107,920-acre Diablo Mountain Wilderness Study Area (OR-001-058) in order to evaluate its mineral resources. The study area is located 1n Lake County, OR, about 45 miles northwest from Lakeview. The study area is located near the northwest corner of the Basin and Range physiographic province. Tertiary Picture Rock basalt with tuff interbeds underlies the area (Travis, 1983). No mineral resources were identified; no mines, prospects, claims, or mineralized areas exist in or adjacent to the Diablo Mountain study area.

Jan 1, 1987

By D. F. Scott

The purpose of this study was to determine if miners were at risk from exposures to chemicals used in the mining industry and determine the nature and sources of the illnesses and injuries. The U.S. Mine Safety and Health Administration?s (MSHA) employment and accident, injury and illness database was reviewed. There were 2,705 cases of chemical-related injuries and illnesses reported from 1999 through 2006, involving 66 different chemicals. The main source (cause) of chemical-related cases was acids/alkalis (about 39%). The primary nature (effect) of chemical-related cases was chemical burns (about 57%). The job classification where workers incurred the most chemical-related injuries and illnesses was cleaning plant operator/media operator/boney preparation plant operator/crusher worker (cleaning plant operators are responsible for maintenance of plants, media operators are responsible for handling reagents, boney preparation plant operators oversee removal of ?bone? from coal, and crusher workers use large crushers to break mined material). From 1999 through 2006, the rate of ?nonfatal days lost? and ?no days lost? (resulting from injuries) did not change significantly; however, the rate of illnesses decreased significantly. Chemical burns accounted for a large number of injuries; mining companies should carefully examine their personal protective equipment (PPE) requirements, training methods and safety culture to ensure that their workers are protected.

Jan 1, 2009

By R. V. Ramani, V. T. Burgos, J. A. McClay

Model testing is a two part operation; first, to assure the valid¬ity of the mathematical statements and second, to evaluate the accuracy of the computer model for predictive purposes. Verification of both the conceptual and computational aspects can be achieved through the use of input data for which output results are available for comparison. In this dissertation, two test problems were selected for model testing from the Economic Evaluation Reports of the U.S. Bureau of Mines, Process Evaluation Group. Verification Data Set I Input data for this test was selected from an economic analysis of a hypothetical 1,056,000-ton-per-year mine in a 48-inch bituminous coal seam (Process Evaluation Group-Report No. 72-27, 1972). The mine was scheduled to operate five days per week, three shifts per day, 220 days per year with an estimated life of 20 years. Coal reserves covered an area of 6.4 square miles with an expected recovery rate of 70%. Production was achieved through 4 continuous miner sections with an average production rate of 400 tons per shift. The cost summary in the report included a breakdown of equipment and labor requirements. A depreciation schedule listed the expected capital expense per year of operation, assuming capital replacement with identical units and no change in the unit cost. Supply and oper¬ating costs were listed in both gross annual figures and cost per ton of production. The operating and investment costs were projected over the 20 year mine life and a discounted cash flow analysis performed to determine

Jan 1, 1975

Mining and reclamation procedures that meet the requirements of SMCRA are illustrated on pages 8 and 9 for each of the three major surface coal mining methods -- area mining, contour mining, and mountaintop removal mining. The three methods involve the same basic steps: clearing the land of trees and other vegetation, removing topsoil and overburden, mining the coal, and reclaiming the land. Although all three methods would not usually occur on any single site, the illustration facilitates comparison of mining and reclamation methods and aids basic understanding of the reclamation processes that take place under SMCRA. Area Mining The area mining method is commonly used to mine coal in the flat to moderately rolling terrain found principally in the western and midwestern states. After the overburden is excavated down to a coal seam, the mining area is enlarged horizontally to expose more coal for removal. In the West, where coal seams are commonly 10 to 20 feet thick (and range up to 100 feet thick in the Powder River Basin of Wyoming), the life of some mines maybe more than 50 years. In the Midwest, coal seams are typically 3 to 7 feet thick and 75 to 100 feet below the surface. Because of the large expanse of area mines and their relatively unrestricted sites, enormous equipment is used to remove overburden and reconstruct the land. The area mining operation in the illustration is on land that was formerly used for farming. The drawing shows that the agricultural use is being reestablished immediately following reclamation. Mining is proceeding across the land toward the left side of the site. The initial excavation was made far enough away from the stream along the right edge of the site to prevent damage to the water supply. The coal under most of the site has been removed, and reclamation has been completed on some of the land. For example, some of the cattle in the foreground and those in the feedlot behind the silo are grazing on reclaimed land that has been mined. At the far left of the illustration, topsoil from the unmined area is being removed by scrapers, transported across the area of active mining, and immediately spread on the land on the right, which is being reclaimed. (Reclamation of mined land as soon as practical, as required by the Act, is called contemporaneous reclamation.) A

Jan 1, 1992

By S. H. Ash

The United States Bureau of Mines has published relatively little on the flooding and unwatering of coal and metal mines. Bulletin 229, Fifty-Nine Coal-Mine Fires, published in 1927, contains several instances of the flooding of mines or sections thereof to extinguish fires but does not describe their unwatering. Report of Investigations 2649, Explosion Hazards Incidental to Unwatering Coal Mines, published in 1924, warned against the possibility of gas accumulations in flooded mines and indicated the precautions to be taken. Report of Investigations 2255, An Unusual Hazard in Reopening Long-Flooded Timbered Metal Mines, published in 1921, told of methane being pocketed and the danger thereof. The flooding of mines originates in many ways. At some mines flooding followed reopening after what was thought to be permanent abandonment; also, explosions have caused some mines to be flooded. Extinguishing fires, accidental encountering of underground streams or flooded old workings, and caves of strata admitting water from underground workings, water-bearing strata, or surface accumulations have also flooded all or parts of mines. Unfortunately, un watering often necessitates much study and causes apprehension largely because experiences in similar situations are not generally known, as few descriptions of successful or unsuccessful methods are available. The job has sometimes been contracted for outside the local management involved and has become a matter of record for the contractor only. As the cost-plus contract system often employed in the past is now known to be expensive, careful managements elect to handle the problem themselves, in line with the general policy of cutting expense where possible. This report describes specific in-stances of successful unwatering by operators.

Jan 1, 1933

By Jr. Norman

Thermoelectric properties of depleted uranium selenides and tellurides were investigated from room temperature to 700 C. Several depleted uranium monoselenides and monotellurides were doped with selected cationic and anionic materials to determine the effect of impurity additions on the thermoelectric properties. The undoped uranium selenides and tellurides were semimetallic conductors exhibiting low Seebeck coefficients and electrical resistivities. Partial or complete degeneracy was in evidence, indicating a charge carrier energy distribution similar to that in a metal. Doping increased the Seebeck coefficients of the uranium monoselenides and monotellurides; however, the corresponding change in the power factor in the figure of merit was small because of the increase in electrical resistivity.

Jan 1, 1965

This U.S. Bureau of Mines (USBM) report conveys the results of an economic analysis of minerals in the West Mojave Management Area (WMMA), including the Desert Tortoise Priority Habitat (DTPH), a proposed special land management area. Undiscovered mineral resources were estimated for the entire WMMA, which totals 8.7 million acres. Known mineral resources were studied for the DTPH, which is an area of 1.2 million acres contained within the WMMA. Federal lands within the WMMA are managed by the Bureau of Land Management (BLM). The WMMA includes Federal, State, and private lands in the western portion of San Bernardino County and the eastern portion of Kern County. The center of the study area is 20 miles northwest of Barstow, California (Figures 1 and 2).

Jan 1, 1993