Search Documents

The Bureau of Mines equipped a longwall shearer with a water-jet-assisted cutting system and measured dust levels during the cutting of a simulated coal block. The block was cut dry, at a conventional water spray pressure of 190 psi, and with water-jet-assisted cutting pressures ranging from 1,000 to 6,000 psi. At water pressures of 3,000 psi and higher, dust concentrations were reduced by as much as 85 pct via water-jet-assisted cutting in comparison with conventional water sprays. This reduction was achieved without any increase in the water flow rate.

Jan 1, 1986

By Chas. F. Jackson

This paper is a tabular compilation of data contained in a series of information circulars dealing with mining methods and costs at a large number of mines in the United States and some foreign countries. There circulars have been published from time to time during the years 1929 to 1934 inclusive. From time to time, as enough data became available in these circulars, other circulars and. bulletins have been published in which the data bearing upon different phases of nine operation were summarized, discussed, and analyzed. The present paper is a compilation of data on costs of drifting and crosscutting contained in earlier circulars, .designed to assemble this information in a convenient form for reference without attempting lengthy discussion of details of drifting and crosscutting practice. For such details the reader is referred to the circulars on individual mines.

Jan 1, 1935

By R. Barany

The heats of formation of anhydrous ferric sulfate and anhydrous indium sulfate were determined by solution calorimetry. At 298.15° K the heats of formation from the metal, rhombic sulfur, and oxygen were -615.6 ±O.7 kcal/mole for ferric sulfate and -649.6 ±O.6 kcal/mole for indium sulfate. Heats of decomposition at 298.15° K are given for the reaction that forms metal oxide, sulfur dioxide, and oxygen) and for the reaction that forms the metal oxide and sulfur trioxide.

Jan 1, 1965

Several short color films describing new technology developed through Bureau of Mines research are available on a loan basis. The films review results of Bureau research programs aimed at aiding the minerals industry by increasing mine productivity, ensuring worker health and safety, and enhancing minerals recovery, processing and recycling. Most of the films are available in a choice of for mats: 16mm film, ½" VHS cassette tape, or ¾" U-matic tape. The films are loaned by the Bureau of Mines free of charge; borrowers are requested to pay only the return postage and for any damage to the films. All titles are also available for purchase in 16mm or videotape formats. Interested persons wishing to borrow or purchase a film should specify its title and the preferred and alternate showing dates. All requests should be addressed to: Motion Picture Library Bureau of Mines Cochrans Mill Road P.O. Box 18070 Pittsburgh, PA 15236 A short description of each film follows: Safer Coal Mining Equipment Traces the development of modified conventional and continuous mining equipment, beginning with an investigation of the problems encountered with mining equipment and continuing through long-term testing of the modified equipment in two mines. "Human engineered" coal mining machines are shown in operation. These machines include features such as adjustable cabs, easy access controls, improved illumination, and other safety improvements. (19 min)

Jan 1, 1986

This report presents a Bureau of Mines study comparing the construction costs, leakage measurements, and predicted performance of different types of large stoppings built and tested in a room-and-pillar oil-shale mine. The six full-sized structures (30 ft high by 55 ft wide) included both permanent and temporary stoppings and were fabricated using materials ranging from structural steel to coated brattice cloth. Leakage across each stopping was measured at differential pressures ranging up to 1.0 in w.g., using both the brattice window method and sulfur hexa-fluoride (SF6) tracer gas. Blast air pressures resulting from a full-scale face blast of approximately 1,800 lb of ammonium nitrate-fuel oil (ANFO) explosives were measured across two of the stoppings and the pre-and post-leakage rates were compared for all the stoppings. Overall performance of the stoppings for production applications was evaluated using an operational model of a two-panel oil-shale mine. Different combinations of temporary and permanent stoppings were evaluated based upon ventilation performance and construction and operating costs.

Jan 1, 1988

By Oliver Bowles

The exingencies of a world war have brought home to the American public, especially the people of the. Eastern States, the urgent need for conserving fuel. Transportation problems in the East have created an unprecedented situation wherein fuel-oil supplies are greatly restricted, and the consequent increase in demand for coal further complicates the problem of transporting and storing that commodity. People should awaken to the need for utilizing every possibly means of conserving to fuel, even to the extent of reducing the temperature in their homes.

Jan 1, 1942

By Jacqueline A. McClaskey

The U.S. Bureau of Mines (USBM) Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U. S. economy. The USBM's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the USBM survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1994

By John B. Gayle

During studies of the various methods for determining and specifying the factors that indicate whether a particular coke is better or worse than other cokes for metallurgical uses, questions arose as to the precision of screen-analysis tests on coke. Although the usual index of precision, the standard deviation of the test result, gives a measure of the precision of these data, the experimental determination of the standard deviation for a particular set of conditions requires tests on a large number of duplicate samples. Because this procedure necessaily involves a great deal of labor, an equation for predicting standard deviations from theoretical considerations has been developed. Results predicted with this equation agree satisfactorily with the experimental values and are applicable to tests on coal, coke, gravel, and other bulk materials.

Jan 1, 1952

By R. Havens, B. K. Shilber

"INTRODUCTION In the course of the investigation of the occurrence of manganese deposits in the western United States, ore-dressing tests were made on three samples procured by Bureau of Mines engineers from two properties in southeastern Juah County, Utah, each of which is known by the name Black Jack. To avoid confusion, the tests will be described under the names of the owners Kendall-Duvall and the Empire Mines.None of the samples were amenable to ore dressing for the production of high-grade manganese sinter.Ores from the Kendall-Duvall deposit represent an interesting metallurgical phase of low-grade manganese occurrence, as the occurrence of manganese as silicate (braunite) automatically governs the extent to which they can be beneficiated by mechanical methods of treatment. As less than 50 percent of the total manganese was recoverable by complex methods of treatment in a 40- percent-manganese sinter, attempts were made to recover most of the manganese in a low-calcite, intermediate-grade product that might be acceptable for subsequent metallurgical treatment. By selective flotation of calcite and manganese, up to 68 percent recoveries were obtained in plus 20-percent manganese products..No encouragement can be given for successful ore-dressing of Empire ores as represented by samples received for testing, as no products were obtained that would meet minimum marketing specifications. Empire ore contained only 1 percent lime and might be high enough in grade (19 percent manganese) for direct hydrometallurgical treatment."

Nov 1, 1947

By Bernard Porter

The solubility of UO2 was determined at 1,250° C. in ternary melts of UF4 and BaF2 with CaF2, LiF, and SrF2. The solubility of Ce02 was measured at 800° and 850° C. in a solution of CeF3, BaF2, and LiF. The amount of La203 which dissolves at 950° C. in a binary mixture of LiF and LaF3 and a ternary of LiF, LaF3, and BaF2 was also measured. In each case, the amount of soluble oxide was mound to be less than 5 weight-percent. A procedure was developed for filtering fused, oxide-saturated fluoride melts in order to obtain a representative sample for chemical analysis. The oxide content of the samples was determined by an inert-gas fusion procedure.

Jan 1, 1961

By Irving Hartmann, Edward Thomas

"INTRODUCTION Adoption of rubber-tire shuttle cars underground in conjunction with mobile coal-loading machines has introduced new problems in the control of dust on mine roadways. Where this type of loading and transportation is used, development and extraction are generally rapid, with the result that much coal is spilled from the shuttle cars during normal operation, Coal in the roadways from this source and from sloughing of the ribs is ground to fine dust by the wheels of the 'shuttle cars and by the treads of the loading and mining machines. The coal dust usually is somewhat contaminated by pulverized rock, and the mixture could not be loaded with the run-of-mine coal without undue contamination of the product even if it were cleaned up promptly.The presence of large quantities of fine, loose dust, which is constantly stirred up and kept in suspension in air by the traffic, constitutes a grave explosion hazard, reduces visibility along the roadways, and is physiologically harmful to the workmen who breathe the air. From the operating standpoint the loose material is undesirable along the roadways because it provides poor traction for the trucks and thereby increases wear and power consumption. The dust-explosion hazard could be eliminated or reduced by frequent application of sufficient rock dust on the roadbed; but this would not remedy the other difficulties, and in fact it might intensify them. Where practicable, the most direct and effective safety measure is to clean up and remove promptly all dust that forms and settles on the roadways. Unfortunately, in many cases this procedure is not feasible. A third Suggested remedy is to prevent dispersal of the dust into the air and to promote its consolidation on the floor by wetting the dust particles.During the past few years several mines have used calcium chloride on shuttle-car roadways to allay the dust thereon. When exposed to the' humid atmosphere of the mine this salt absorbs Moisture from the air and deliquesces, and in this way wets the dust on the floor of the roadway. In a survey conducted in coal mines in southern West Virginia and in eastern Kentucky where calcium chloride has been in use, somewhat conflicting re- ports were received regarding the merits of the application, and several operators have abandoned the practice either because of actual or assumed disadvantages. The purpose of the study described in this report was to collect and correlate evidence and, on the basis of experimental data obtained in the field and in laboratory tests, to present a clearer picture of the factors involved in the allaying of dust by use of salts."

Sep 1, 1945

By Powell. Alfred R.

"An investigation has been made of the applicability to a variety of coals, other than those from Illinois, of the Powell and Parr method of analysis for the forms of sulphur in coal.A complete study was made of the sulphur in the following coals:- Upper Freeport, Pa.; Pittsburgh seam, Pa.; Pocahontas No. 3, W, Va..; Letcher Co., Ky.; Morgan Co., Tenn.; and Cherokee Co., Kan.The method of analysis gave excellent results when applied to these coals. In the determination of pyrite, the iron-sulphur ratio checked in every case with the theoretical. After the extraction of the pyrite and sulphates, the remaining sulphur was proved to be organic in nature.This work indicated that sulphur exists in coal in three typical forms: - pyrite or marcasite, sulphates, and organic sulphur. A study of the changes which these forms undergo during coking has been made on a variety of coals, and the following five classes of reactions established.First. Complete decomposition of the pyrite and marcasite to ferrous sulphide, pyrrhotite, and hydrogen sulphide. This reaction begins at 300°C., is complete at 600 °C., and generally reaches its maximum between 400 and 500°C."

Mar 1, 1920

By A. W. Ambrose

A few years ago, (March 3, 1915) Congress passed a law providing for the establishments of ten mining experiment stations under the supervision of the Bureau of Mines. In 1917 the Secretary of the Interior decided that one of these stations should be devoted to Petroleum, and in the early part of 1918, approved the establishment of the Petroleum Experiment Station at Bartlesville, Oklahoma, upon the condition that the city furnish the site for the buildings and guarantee $50,000. for the erection of the buildings. A building site of 5 acres and the necessary building fund was furnished by the Bartlesville Chamber of Commerce.The buildings consist of an administration and laboratory building, both of brick construction. The former is a two-story structure of eight rooms. A large room occupying over half of the main floor is devoted to the library, reception room, and clerical force. The remaining rooms comprise a drafting room and six offices occupied by the staff assigned to this station. The laboratory is a one-story brick building and contains a well-equipped chemical and physical laboratory, also a machine shop and mechanical laboratory. In addition to the main buildings there now are on the property an experimental refinery, a blue-print house, and a store house. These latter buildings are all of sheet-iron construction.

Oct 1, 1920

By H. R. Babitzke, H. Kato, R. E. Siemens

An investigation was made to provide further information for evaluating columbium- hafnium alloys for use as high - temperature structural materials . The columbium- hafnium system was investigated between 700 ° and 2,400 ° C by melting point , thermal analysis , X - ray diffraction , electrical resistivity , and metallographic techniques . The equilibrium diagram is the beta isomorphous type , with columbium tending to stabilize the beta phase . Addition of 60 atomic percent columbium stabilizes the beta phase at 700 ° C. The allotropic transformation temperature of hafnium is 1,750 ° ± 20 ° C. A minimum melting point occurs near 75 atomic percent hafnium .

Jan 1, 1964

By J. E. Pahlman

The Bureau of Mines performed research on a fluid-bed magnetic roasting process for nonmagnetic taconites that utilizes low-rank coals and lignites as reductants and fuels. Roasting tests on a Michigan nonmagnetic taconite were conducted at 600° to 725° C with lignite or subbituminous coal as reductants. Partial combustion of the reductant reduced the amount of heat externally applied to the reactor to maintain the desired reactor temperature. Cleaned, dried reactor top gases were recycled to recover a portion of the reducing potential in these gases without adversely affecting concentrate grade and iron recovery. Highest iron recoveries for magnetic concentrates were obtained at a roast temperature of 650° C with lignite and at a roast temperature of 725° C with subbituminous coal. Magnetic concentrates were obtained that were comparable with commercial concentrates.

Jan 1, 1976

By A. B. Clayton

The Bumpus Cove area is in Unicoi County, Tenn., about 9 miles south of Jonesboro and 5 miles northwest of Erwin. Iron and lead ores were mined in the Bumpus Cove area before the American Revolution. The production of those metals continued intermittently until 1916. In 1850 this area was the most important producer of iron in the South. In 1911 several carloads of zinc ore was recovered from old dumps and shipped to Missouri smelters. In 1913 systematic mining of zinc ores was begun and continued until 1916. After that year, mining again became sporadic and continued so until discontinued in 1943.

Jan 1, 1949

By W. T. Abel

Laboratory tests were conducted with a closed, recycling system to evaluate the effectiveness of solid-in-gas suspensions as heat transport mediums. Micronized graphite in helium or nitrogen was circulated by a centrifugal compressor to determine the feasibility of the method and heat transfer capabilities of the mediums. Suspensions were circulated without plugging or eroding the compressor or piping. At low flowrates and light (0.1 to 0.2 volume-percent) graphite loadings, slightly less power was required to transport a given amount of heat with suspensions than with helium alone. Graphite deposition on the heat exchange surfaces of the cooler decreased the heat transfer effectiveness at higher solids concentration. Efforts to eliminate deposition are described.

Jan 1, 1963

By H. P. Hermance

The Ore Hill zinc-lead mine in Grafton County, N. H., was investigated by the Bureau of Mines from March to July 1943 and from August to October 1944. Fourteen holes with an aggregate bore of 4,899 feet were diamond-drilled, the old workings were unwatered and sampled to an inclined depth of 250 feet, and the tailings dumps were surveyed and sampled. The deposit at the Ore Hill mine comprises a bedding-plane vein of massive sphalerite and galena with subordinate chalcopyrite and pyrite in a series of interbedded metasedimentary and metavolcanic schists about one-quarter mile east of their contact with the intrusive Baker Pond gneiss. The property was first opened about 1850 and was active at times to 1914. Production records are not available, but the output is believed to have been considerable. In 1944, leasers recovered a marketable mica product from mica schist from the dumps and certain outcrops. This report describes the work performed in the Bureau's investigation and presents the data obtained.

Jan 1, 1948

By Mary H. Brown

The heats of formation of oxalic acid and sodium, potassium oxalates, and lithium oxalates were related by solution calorimetry to the heat of formation of (COOH)2.2H20, a value believed to be reliable as reported in the literature. The following heats of formation were determined: (COOH)2(a), -198.1±0.1; (COOH)2(ß), -197.8±0.1; UAW,, -328.7±0.4; Na2C204 -316.2±0.1; K2C204, -321.9±0.2; and K2C204-H20, -393.5±0.2 kcal/mole. The heat of the crystalline transformation (COOH)2(a) ? (COOH)2(ß) was determined to be 0.30±0.02 kcal/mole at 298.15° K.

Jan 1, 1970

By R. W. Dalzell

The performance characteristics, efficiency, and operating pressure of jute line-brattice systems were studied under varying underground conditions; various fabric grades and installation methods were used. The test results indicate that line-brattice system efficiency is dependent upon the method of ventilation the method of installation, porosity of fabric, and size of tight rib area.

Jan 1, 1966