Search Documents

By L. W. Kelly

The primary purpose of this paper is to show the appreciable savings that were made by roof-bolting the main west entry of the Kings mine, which was to be the permanent, main haulage road, as compared to the cost of supporting the same roof with peg timbering as first planned. Additional items that might prove valuable to other mine operators are contained in this paper and detailed below. 1. A detailed cost of the system of roof support known locally as the peg-timbering method is given. It consists fundamentally of supporting steel cross bars on pegs inserted into holes drilled in the ribs close to the roof. 2. A method of supporting the roof in caved entries is shown, where such support must endure for an extended period in haulageways and air courses.

Jan 1, 1952

By John J. Mulligan

Since 1941 the Federal Bureau of Mines has been conducting an intermit-tent program of placer and lode investigations to evaluate the potential tin resources of the western Seward Peninsula tin belt. Previous investigations were made in the Potato, Cape, Brooks (Lost River), and Ear Mountain areas. As part of this program the Bureau made a reconnaissance of reportedly tin-bearing stream gravels in areas adjacent to the previously worked tin deposits at Lost River and Potato Mountain. The objective of the reconnaissance was to determine if additional areas might be favorable for lode or placer exploration. The work was begun late in the fall of 1956 and completed during the following summer. The streams sampled were the Lost River and York Creek in the Brooks Mountain area and the Anikovik River and Kigezruk and Baituk Creeks in the York area. Samples were obtained by churn-drilling methods employing conventional placer-evaluation procedures. Holes were drilled at wide intervals at sites chosen as being representative of drainage areas rather than of individual gravel deposits. Minor to trace amounts of tin were found in the gravels of all these streams, but the highest grade was 0.35 pound of tin per cubic yard in the gravels of Lost River below the mouth of Tin Creek. Small amounts of gold were found on Baituk Creek and in one hole on the Anikovik River; the highest grade did not exceed 10 cents per cubic yard. Traces of scheelite and barite were found on York Creek, chromite was encountered in one hole on the Anikovik River, and minor amounts of titanium minerals (probably derived from basaltic intrusives) were found in the York area.

Jan 1, 1959

By John E. Miller

Absolute viscosity values for gases usually are determined with a capillary tube viscosimeter, One of the correction factors applied to the experimental data is that for nonuniformity of the capillary bore. This report contains useful analytic expressions of the nonuniformity correction for the following cases: ellipse, cone, sine wave, sawtooth wave, square wave, and the general case. The methods herein described are applied to estimate the nonuniformity of a section of stainless steel capillary tubing to be used at the Bureau of Mines Helium Research Center. Several other examples are given to illustrate the usefulness of the present results.

Jan 1, 1967

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

8. Refuge Chambers 8.1 Refuge Chambers - Technical Discussion 8.1.1 Introduction As a part of the overall escape system, refuge chambers can provide a last resort when existing escapeways are blocked. These chambers are intended to provide both protection from toxic gases and a life supporting environment for a period of time before external rescue or further escape efforts can be carried out Escapeways may be blocked physically (due to cave-ins, etc), by fire, or by the presence of a toxic or oxygen deficient atmosphere. In the first two cases, the trapped miners would most likely await external rescue efforts, and hence the design of the chamber will have to consider the time durations that such efforts may take, It is also possible, in the second case, for fire fighting and fire protective equipment to be stored in the chamber so that miners may attempt their own escape. In the third case, it should be recognized that a compact, beltmounted 1-hour self-contained breathing apparatus has been developed(9), and that other, less compact equipment is available for up to 4 hours of self-contained breathing supply. If such equipment were stored in the chambers, then miners could escape by travelling from chamber to chamber, taking temporary refuge in each before proceeding to the next. 8.1.2 Background The concept of "barricading" has long been recommended for those emergencies where miners are trapped inby a fire. Barricading, which is the construction of a makeshift shelter in a crosscut or deadend, protects the entrapped miners from toxic gases and enables them to conserve a supply of air. In this manner, they can survive two or three days--hopefully enough time for them to be reached by rescue teams. In the past, many lives have been saved with this technique.

Jan 1, 1976

In 2006, data obtained from the Mine Safety and Health Administration (MSHA) indicated a total of 935 underground (6.3%) and 13,950 surface (93.7%) mining operations.1

Jan 1, 2008

By Frank J. Wiebelt, Spangler Hicker

The Iron Mountain investigations were part of a comprehensive program for making a national inventory of raw materials used in the production of steel. A tentative program of core drilling by the Bureau of Mines was set up for exploration of more promising iron deposits. Iron Mountain was selected as worthy of investigation because it could serve as a potential source of ore for the war-created steel plant at Fontana, Calif. The deposits were reported on by an engineer in October 1943. The purpose of the project was to determine the lateral and vertical extent of ore bodies and to obtain accurate material data on them.

Apr 1, 1948

By E. G. Davis

The Bureau of Mines studied tailings samples from 11 large-scale western copper operations to determine the potential for recovery of rutile and other critical and strategic minerals. Up to 15 pounds per short ton (lb/st) Ti02 was found ion these samples; however, only 9 to 44 pct of the Ti02 was liberated rutile. For one sample, gravity preconcentra-tion, grinding, and flotation recovered 34 pct of the Ti02 in a 54.8-pct-Ti02 concentrate. Over 0.38 Ib/st W was found in some of the tailings sampleso Scheelite was identified as the major W mineral. Nine of the eleven samples contained about 0.02 to 0.18 Ib/st Co. Pyrite was the principal Co-bearing sulfide mineral, with Co contained in about one-fifth of the pyrite grains. Up to 30 pct of the Co was concentrated in a bulk sulfide flotation concentrate.

Jan 1, 1988

By Hillary W. St. Clair

This report gives the results of an experimental study of the progressive changes that occur in particle size and size distribution when a homogeneous and isotropic mineral is subjected to crushing by impact. The mineral used in the study was uniformly sized quartz, which was crushed in a simple drop¬-weight machine that applied impact energy up to about 100 kg-cm per g. Screen analyses of the crushed products were analyzed by the method of moments to determine the mean size, variance, skewness, and kurtosis. Analysis of the data from these experiments shows that the mean size of the crushed product is a function of the energy input and the initial size. The size distribution is functionally related to the degree of size reduction. As the mean particle size is decreased, at first there is a corresponding increase in the variance and decrease in the skewness, But, as size reduction is carried further, each tends eventually to approach a steady value, and the form of the size distribution becomes stable.

Jan 1, 1972

By H. O. Poppleton, F. E. Block

This investigation was made to develop a method of preparing high - purity thorium metal in quantities up to 20 kilograms per batch . Several methods for the preparation , purification , and reduction of thorium tetrachloride are discussed . Thorium tetrachloride was prepared by chlorination of decomposed thorium nitrate or oxalate with carbon tetrachloride or phosgene . tion of the crude tetrachloride was achieved by multiple distillations or by filtration of the molten chloride . It was found that high - purity thorium metal could be prepared by sodium reduction of thorium tetrachloride if chloride of sufficient purity were available . Byproduct salts and excess reductant were removed by vacuum distillation , and the resultant thorium metal sponge was consolidated by consumable - electrode or fixed - electrode arc melting . It was demonstrated that metal prepared by this method could be fabricated into bar , rod , or sheet , at room temperature .

Jan 1, 1964

By P. J. Colbassani

Samples of mine atmospheres collected by Federal coal-mine inspectors during their inspections and investigations of coal mines, in accordance with provisions of the Federal Coal Mine Safety Act (66 Stat. 692; 30 U. S. C., sees. 451-483) are analyzed routinely by chemical methods at Bureau of Mines laboratories. When samples collected in open workings of nongassy coal mines at points not less than 12 inches from the roof, face, or rib contain 0.25 percent or more methane, the act requires the operator, during operation of such mine, to comply with the provisions of sec. 209, Title II, of the act, which pertain to gassy mines. The methane con-tents of such samples are determined by a physical method based on infrared absorption spectrometry to provide an independent check on analytical results obtained by chemical methods. This information circular describes the equipment and procedures used by the Bureau for determining low concentrations of methane in coal mine atmospheres by infrared absorption spectrometry. ACKNOWLEDGMENTS The authors are indebted to Dr. R. A. Friedel, Chief of Spectrometric Section, Branch of Coal-to-Oil Research, Bureau of Mines, for suggesting the analytical method and for furnishing valuable advice and assistance, and to J. A. Queiser of his staff for making exploratory measurements by this method; to Dr. M. G. Zabetakis of the Division of Explosives Technology for his assistance during the conduct of preliminary experimentation; and to L. B. Berger, Chief, Branch of Health Research, under whose guidance the equipment was procured and the work conducted.

Jan 1, 1958

By Jr. Karr

The Bureau of Mines studied the influence of carbonization method, temperature, and carrier gas on the composition of eight different low-temperature tars produced from a Colorado subbituminous coal. A fluidized bed was compared with an entrained bed, temperature was varied from 500° C to 650° C, and external heating using recycle gas as the carrier gas was compared with internal heating using oxygen-containing gas. The entrained bed yielded significantly more m-cresol and m-ethylphenol, indicating that thermodynamic equilibrium was more nearly approached in the system. Increasing the temperature greatly increased the yield of benzenes and naphthalenes, while paraffins, olefins, and total tar acids were reduced. Using oxygen in the carrier gas decreased the yield of low-boiling phenols and increased that of paraffins and olefins at 650° C.

Jan 1, 1966

By R. E. Morgan, Barkleym J. F.

"INTRODUCTION Wood burned for commercial heat and power usually is waste material from some manufacturing process. The amount of it reaches substantial proportions. It is estimated that over 50 percent of the timber cut for lumber becomes ""waste"" in the process - sawdust, shavings, trimmings, slabs, and bark. Woodworking manufacturing processes also produce much waste. The incentive to use this waste has resulted in much development of wood-burning equipment to produce heat and power. To answer general inquiries received by the Bureau, this publication covering developments along these lines was written. There is included a bibliography of additional information on the subject.COMPOSITION AND BURNING CHARACTERISTICS OF WOODThe approximate composition of moisture-free wood is, in even figures:PercentHydrogen 6Carbon 49Oxygen 44Ash 1Total 100This composition corresponds to about C6H1005. Moisture is essentially always associated with wood. Green wood contains approximately 30 to 50 percent moisture; air-dried or seasoned wood contains 15 to 25 percent and kiln-dried about 8 percent. Exposed to the weather, wood absorbs and gives off moisture depending on weather conditions and water contact.""Dry"" wood ignites relatively quickly and readily gives off volatile matter when heated. Long flames and smoke easily occur during burning. The burning action is substantially retarded, however, by appreciable moisture content; ignition is more difficult. When the moisture content is more than about 70 percent, an auxiliary fuel is required to maintain combustion. One of the main factors in the problem of the satisfactory and smokeless combustion of wood is its moisture content."

Sep 1, 1950

By Terry J. Close

The Anaconda Pintlar Wilderness has a significant mineral resource potential. Five deposits have resources totaling about 180,300 tons (163,600 t) containing silver, copper, lead, gold, and zinc. Another 11, not sufficiently exposed to allow resource estimates, may have additional mineral potential. No placer deposits are indicated. There is little potential for the production of sand, gravel, or stone; alternate sources are closer to markets. No oil, gas, uranium, or geothermal energy sources are known to be present.

Jan 1, 1982

Pillar design is the first line of defense against rock falls—the greatest single safety hazard faced by underground coal miners in the United States and abroad. To help advance the state of the art in this fundamental mining science, the National Institute for Occupational Safety and Health organized the Second International Workshop on Coal Pillar Mechanics and Design. The workshop was held in Vail, CO, on June 6,1999, in association with the 37th U.S. Rock Mechanics Symposium. The proceedings include 15 papers from leading ground control specialists in the United States, Canada, Australia, the United Kingdom, and the Republic of South Africa. The papers address the entire range of issues associated with coal pillars and have a decidedly practical flavor. Topics include numerical modeling, empirical design formulas based on case histories, field measurements, and post failure mechanics.

Jan 5, 1999

By George L. Gates

It is generally recognized that if the lose and contamination of the fluid content of a core specimen from an oil- and gas-bearing formation in a well were eliminated, the value of core analysis would be increased greatly. In an effort to obtain uncontaminated cores, extensive field tests were carried out in the Mercy field, San Jacinto County, Tex., with the Carter pressure core barrel and an oil-base drilling fluid having very low rates of filtration as measured by the standard A.P.I. drilling-fluid filter teat. A tracer was added to the drilling fluid filter test. A tracer was added to the drilling fluid to provide a means for quantitatively measuring the volume of oil filtrate in the cores. Unfortunately, as stated in the report on the Mercy tests, very little oil nand was penetrated in coring the well; and because the performance of the pressure core barrel was not entirely satisfactory, the tests did not provide a complete answer to the question: Does a filtrate from an oil-base drilling fluid enter cores., and how does it affect the results of the core analyses?

Jan 1, 1950

By J. G. Donaldson

Cobalt-tungsten binary deposits were formed in laboratory experiments by hydrogen reduction of the anhydrous mixed vapors of cobaltous chloride and tungsten hexachloride. The materials were sublimed in seperately heated zones of reaction tube and were transported in a stream of purified helium into the deposition section of the tube where the chloride gases were reduced to metal by a countercurrent flow of hydrogen. Heattreating of the near stoichiometric binary metallic deposits converted nearly all to the intermetallic compound Co3W, however, small quantities of both cobalt and tungsten remained. Mechanical tests showed that the tensile strength of heat-treated 75 percent cobalt-25 percent tungsten deposits was twice as high as that of similarly treated deposits of cobalt.

Jan 1, 1965

By Byron S. Gottfried

This Bureau of Mines report presents a method for combining the distribution curves at different specific gravities of separation, for a given piece of coal-cleaning equipment and a given raw coal feed, into a single, generalized distribution curve normalized with respect to specific gravity and, therefore, independent of the specific gravity of separation. Illustrative generalized distribution curves, based upon Bureau of Mines collected data on industrial operations, are presented for five different types of coal-cleaning equipment. The well-known concept of probable error is extended to the generalized distribution curve. It is shown that the conventional probable error is directly proportional to the specific gravity of separation. A number of sample calculations, illustrating the use of the generalized distribution curve and generalized probable error, are presented in the appendix.

Jan 1, 1977

It is now widely accepted that horizontal stress is present nearly everywhere underground. Often it is more severe than the vertical stress. It is a major cause of roof control problems in underground mines. The AHSEM computer program contains two modules to improve mine layouts for control of horizontal stress. For development, the user specifies the orientations of the maximum horizontal stress, the entries, and the crosscuts. Angled crosscuts may be used, and the angles may be different for the right- and left-hand crosscuts. AHSEM then shows the user how the stress condition would vary as the entry and crosscut orientations are changed. The second module is for longwall mining. Severe stress concentrations can make headgate conditions hazardous when the entries are improperly oriented. AHSEM shows whether a particular longwall orientation and extraction sequence places the headgate corner in a stress concentration or in stress relief. It also estimates the magnitude of the stress concentration.

Apr 1, 2003

By J. B. Janus

This report, the 22d in a series, gives analytical data showing composition and quality of tipple and delivered samples of coal collected during fiscal year 1972. This coverage lists mines located in 20 States. Ultimate analyses are given for most of the coalbeds listed. Tipple samples were collected by Bureau of Mines engineers at tipples as coal was being loaded into railroad cars or trucks. The deliveries were sampled in accordance with instructions issued by the Bureau of Mines, and the samples were analyzed in the Bureau laboratory at Pittsburgh.

Jan 1, 1973

By R. V. Higgins

A numerical method is presented to calculate the isopressure (isobar) lines and streamlines for an oilfield from the pressure distribution. A knowledge of these lines is useful in the study of the flow of fluids in underground reservoirs, especially for those containing gaseous and/or liquid hydrocarbons. This work was done primarily to enable determination of the shape factors needed in the calculation of petroleum reservoir performance. However, it has application for the flow of water in aquifers, or electricity or heat in odd-shaped geometry. Techniques previously developed were used to calculate the pressure distribution. From this pressure distribution, the isopressure lines were calculated accurately by the method presented in this paper. Then by successively projecting orthogonal lines from one isopressure line to another, the streamlines are determined. From the coordinates of the isopressures and the streamlines, the shape factors can then be determined by a published method. Computer methods are presented to calculate the streamlines and isopressures for any well-spacing pattern existing within a field with multiple wells. The method reproduces the flow net for several well configurations having extensive geometrical variations. Such information provides the petroleum engineer with data from which he can compute oil recoveries for different patterns and thereby maximize the recovery of hydrocarbons from the reservoir.

Jan 1, 1972