Search Documents

By Robert H. Townsend

The following paper discusses the mining, transportation, and crushing methods, with costs, at the San Andreas plant of the Calaveras Cement Co. It is one of a series, prepared for and published by the U. S. Bureau of Mine describing methods used in cement-rock quarries throughout the country. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total cost. It is recognized that publication of total costs mightin some instances cause embarrassment to individual producers as well as to the industry as a hole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost-tabulations shall ensue.

Jan 1, 1933

By Donald O. Capstick

[ ]

Jan 1, 1983

By M. R. Geer

American and European practices in cleaning fine coal are strikingly different. The tables, launders, classifiers, and pneumatic devices used in America are seldom employed in Continental Europe, where much of the fine coal is cleaned in feldspar jigs, often supplemented by froth flotation of the extreme fines. This difference in choice of cleaning equipment may be fortuitous, but in large measure can be attributed to a difference in economic factors. Coal being more costly in Europe, there is greater emphasis on efficient cleaning of all sizes, including the extreme fines, and it is common to produce a high-ash middling for "on-site" consumption to avoid any waste of fuel value. The feldspar jig has been found advantageous under these conditions. In the United States fuel coal must be prepared as cheaply as possible, and metallurgical coal must be prepared as efficiently as possible; thus in both branches of preparation practice, any cleaning device that promises greater economy or higher efficiency warrants consideration. The feldspar jig, as employed in Europe, has a much higher unit capacity than the wet table used so extensively here and therefore offers economy in the capital costs of a washery through saving in space. As pointed out by Vissac,4/ the jig operates under automatic control, and therefore can cope with fluctuations in quality of feed. Maintenance costs for a single, large-capacity unit, such as the feldspar jig, would be expected to be lower than those for a battery of low-capacity cleaners. These considerations led the Bureau of Mines to undertake an investigation of the feldspar jig to determine its possible usefulness in this country.

Jan 1, 1958

By Eric R. Bauer

This Bureau of Mines manual is intended to provide a better understanding of ground movement and the technology available for measuring it, The manual deals with convergence, strata separation, lateral roof movement, stress, and support load in underground mines. The instruments that measure these ground control parameters are described in detail. Step-by-step procedures for selecting the appropriate instrument are presented, which consider such factors as approximate cost, installation procedures, data collection, and data interpretation; and an instrument selection worksheet is provided to facilitate the instrument selection process. Actual instrument case studies and a list of instrument suppliers are presented in the appendixes.

Jan 1, 1985

By E. G. King

Many of the existing thermodynamic values for the titanium halides are estimates, including all the entropies and high-temperature heat contents of their crystalline and liquid phases. This report contains the results of low-temperature heat capacity measurents (which lead to entropy values at 298.15° K,) and high-temperature heat-content measurements of four halides - trichloride, tribromide, tetrabromide, and tetraiodide. The new data are combined with selected heat-of-formation values at 298.15° K. to obtain improved values of the heats and free energies of formation of these halides at high temperatures, thus supplementing the previous data of Kelley and Mah.5/ ACKNOWLEDGEMENTS This investigation was conducted under a cooperative arrangement between the Federal Bureau of Mines and the Department of the Navy, Office of Naval Research. The work was done by Bureau of Mines personnel using Bureau of Mines calorimetric equipment. The Office-of Naval Research supplied the supporting funds and arranged for procuring the samples of the titanium halides. The samples were prepared and analyzed by the Inorganic Chemistry Section, Division of Chemistry, National Bureau of Standards.

Jan 1, 1961

By Dennis A. Hansen

The solubility of anhydrous aluminum chloride in solutions of titanium tetrachloride and vanadium tetrachloride was determined as part of a re-search project-by the Bureau of Mines to make a homogeneous alloy sponge of titanium, vanadium, and aluminum. Solubility curves were established using an autoclave at 75°, 100°, 125°, and 150° C. The solubility of AJC13 in TiC14 is 0.2 wt pct at 75° C; it increases to 18.3 wt pct at 150° C. The data concur with data from earlier researchers of this bi-nary system for 75° to 125° C. For the VC14-AlC13 binary system the solubility of AlC13 is 0.1 wt pct at 75° C, increasing to 1.6 wt pct at 150° C. For the TiC14-AlClrVC14 ternary system the solubility of AlC13 decreases from the values found with a pure TiC14-AlC13 system to the lower values found with a pure VC14-AlC13 system at the respective temperatures.

Jan 1, 1986

By John D. Foulkes, David A. Curtis, Robert L. Lagace, John L. Rothery

An investigation is made of the feasibility of developing compact transmit antennas and/or other means to efficiently couple VLF to MF band radio energy between portable wireless communication units in coal mines. The completely wireless communication ranges between two portable radios equipped with practically-sized reference loop antennas in representative coal mine environments are estimated. Antenna technology is assessed with respect to transmit moment, range, intrinsic safety, battery and wearability requirements to deter- mine the most suitable antenna types for use by miners. It is concluded that air-core bandolier loop antennas, and perhaps ferrite-loaded loop antennas, having peak transmit moments of about 2.5 ampere-m5 will be the most effective antenna choices for portable units. This choice, however, will not allow the range goal of 1350 feet to be attained in mines having unfavorable signal attenuation and noise environments. Rectangular air-core loops are compared with grounded horizontal-wire and vertical-wire mode exciters for fixed station applications. The potential for significantly increasing the wireless communication range by inductively coupling to communications and power lines in a mine is evaluated and found to be considerable based on theoretical coupling equations. Lastly, the theoretical performance of a hybrid noise cancelling diversity receiving technique that utilizes both the electric and magnetic field components of the ambient noise to improve the receiver output signal-to-noise ratio under certain adverse conditions is estimated and shown to be favorable when the magnetic and electric field noise components are highly correlated.

Jan 1, 1977

By Q. H. Forbes

"The high injury rand fatality rate in coal mining, as compared with other industries, has caused the mining industry to become more and more interested in accident prevention methods.The prevention of accidents in the mining industry is probably not as simple a problem as it is in other industries, but if the experience of coal mining companies who have taken up the work of accident prevention seriously during recent years means anything, there is little doubt that most mining companies car improve their accident records very materially.Such results can be obtained in practically all instances without adding to production costs. In fact, there is little doubt that a well-organized program of accident prevention Will bring about a 'material production cost reduction due to increased efficiency, lower labor turnover, fewer delays due to accidents, better satisfied workmen, and a direct saving in compensation costs as well as many other items of expense.The more closely a. person is connected with the work of accident prevention, the more he becomes a believer in the value of amity in human relationships and the more he is able to exercise a spirit of toleration, fairness, justness, and helpfulness toward the problems of others, whatever those problems may be. Human nature responds to just these expressions of good willAnother great and invaluable effect of working for safety, is the fact that it is building up in the mind an appreciation of that which is constructive and, conversely, in opposition to that which is destructive In other words; the person who is sincerely striving to prevent accidents because they are destructive, costly, tad injurious, is subconsciously training his mind to look on any proposition from a constructive point of view. Working for accident prevention and safety is about the finest social training any person can have. It does not make a Person a financial Wizard or an executive genius, but it does make for the highest type of citizenship.While humanitarian reasons alone should be sufficient to maze accident prevention work an important factor in every mining organization, there are other reasons as well, since it has been proved conclusively that there can be no efficiency and economy without safety, as somebody pays when safety is lacking. Every safety device pays dividends; every safety application evaded is an assessment and a loss. Dangerous conditions are the most expensive and extravagant conditions in or about a coal mine. The economic gains are of considerable interest to all coal mining companies and this is brought about as before stated--through decreased compensation rates, the reduction of labor turnover, etc."

Dec 1, 1930

By J. A. Baicker

A prototype borehole probe for ore grade determinations by means of in-situ neutron activation analysis was designed, built, and tested in a two-phase program. Phase I dealt with the design and fabrication of a borehole logging system for operation in 7.6 cm (3 in.) diameter or larger boreholes. It consisted of a 5.06 cm (2 in.) diameter borehole probe containing an intrinsic germanium detector, a canister-type solid cryogen cooling system, cooled FET preamplifier, linear amplifier, high voltage supply, analog-to-digital converter, microprocessor-based multichannel analyzer, buffer memory, bi-directional cable link, power supplies, and a Californium-252 neutron source. A surface support vehicle was designed and outfitted. A minicomputer system was constructed and software developed and tested. In Phase II the system was field tested at several mine sites. The system was calibrated, tested, improved, and demonstrated in a variety of applications. Tests were performed at sites pertinent to uranium, iron, coal, copper, silver and gold. Technical feasibility was demonstrated for all these applications except gold; the gold results were inconclusive. In-situ neutron activation analysis using high resolution gamma ray spectrometry was found to be a potentially viable logging method for are grade analysis under certain conditions.

Jan 1, 1984

By James C. Barker

In 1981 and 1985-1986, the Bureau of Mines conducted orientation studies of marine placer platinum-group metals (PGM). PGM are derived from the Goodnews Bay ultramafic complex and magnetic surveys show that the complex extends offshore at least four mi. The present seafloor was an emergent foreland as recently as 8000 years ago. High-energy ocean processes are transporting and depositing sediment such that PGM-bearing materials are reworked and later masked by barren littoral drift. Exploration targets include 1) placers formed since present transgression began, and 2) ancient marine and drowned fluvial deposits. Additionally, there is evidence of PGM solution transport and accretion. At least minor values of PGM in Recent lag-type placers and possible submarine strands are concentrated along an offshore scarp incised through glacial deposits into the preglacial surface between Flat Cape and Red Mountain. Other Recent PGM-bearing features include Flat Cape shoal, Chagvan Bay, Salmon River delta, and modern beaches. Ancient placers include possible N-S fluvial systems 2 to 3 mi offshore, a nearshore scarp 50 ft below sea level, and strands adjacent to projected ultramafic bedrock slopes. The existance of ancient placers is dependent on depth of glacial erosion. SEM studies show PGM are principally isoferroplatinum and osmiridium, with minor sperrylite, moncheite, and platiniridium. Gold is a co-product, and concentrates comprise chromite, ilmenite, and magnetite. Beneficiation tests successfully concentrated precious metals from natural blacksand accumulations, but failed to concentrate low-grade lag gravels.

Jan 1, 2011

By R. W. Huber

Three arc-melted ingots, two of a titanium-7 percent manganese alloy and the third of unalloyed titanium, were forged and rolled into 3/4-inch plate; comparative data were obtained on these processes. The finished plate, part of which was used by the Naval Bureau of Ordnance, was tested for mechanical and other properties. These properties were correlated with sponge purity, forging technique, rolling temperature, and cooling rate from the rolling temperature. For the alloy material, transformation data were obtained, and their age-hardening characteristics were studied. The temperature-impact relationship was established for rolled sections from all three ingots. INTRODUCTION Arc-melted ingots of unalloyed titanium and a titanium-manganese alloy were fabricated into plate under closely controlled conditions by personnel of the Metals and Alloys Section, Physical Metallurgy Branch, Bureau of Mines, College Park, Md. This program was cosponsored by the Naval Bureau of Ordnance. Bureau of Mines interest lay in correlating the processing procedures with the mechanical properties of the finished plate.

Jan 1, 1955

By E. M. Tignor

As a part of the program of promoting the conservation and efficient utilization of petroleum, studies are being made by engineers of the Bureau of Mines on secondary oil-recovery projects throughout the United States. In furthering that aim, engineering data concerning the reservoirs, methods of stimulating the production of oil, and other pertinent facts are collected, studied, and subsequently published so that others may profit by the experience gained. This report presents the results of a study made by engineers of the Franklin, Pa., office of the Bureau of Mines of secondary oil-recovery operations in the Boggs field, Spencer district, Roane County, W. Va., whore natural gas is injected into the reservoir to stimulate the production of oil from a so-called stripper field. The Boggs field, like most others in the Appalachian region, is one in which the major part of the natural energy that caused oil to flow through the reservoir to the producing wells during the primary stage of oil production has been dissipated. For all practical purposes, most of the oil produced in the Appalachian region at the present time can be considered to be from stripper fields. Consequently, secondary recovery methods are being used extensively in the oil-producing areas of New York, Pennsylvania, West Virginia, Ohio, and Kentucky for recovering some of the oil that was not produced by primary production methods.

Jan 1, 1949

By W. W. Adams

The metal and nonmetallic mineral mines (excluding coal mines) of the United States had a more favorable safety record in 1935 than in any year except 1931 and 1932 since annual statistics of accidents first became available in 1911. The accident rate was even lower than that for 1911, when the recorded rate probably did not reflect all of the accidents that actually occurred because many companies had not yet begun to keep complete records of accidents, especially those causing only minor injuries, and when, therefore, the number of accidents revealed by the companies' reports to the Bureau of Mines was probably not as complete as that reported for later years. Compared. with 1911, the accident rate covering fatal and nonfatal injuries in. 1935 decreased 13 percent. Compared with 1925, when the rate was the highest ever reported, the rate for 1935 decreased 47 percent and compared with 1934, 7 percent. The progress in safety which the mines of the country made in 1935 was not confined to any section or mining region; it was shared by a majority of the mining States and applied to underground mining operations, to open-pit mining, and to work at surface shops and yards. The rate for underground mining declined 8 percent from 1934; the rate for open-pit mining declined 14 percent, and that for surface shops and yards 12 percent.

Jan 1, 1938

By Scott Turner

We are here today to witness the graduation of 63 young men as Engineers in the mineral industries . It is an important occasion and one in which the public takes a keen interest , since this school has long been famous for the educational facilities it affords young men, and for the high professional standing of its graduates . : : : It is fitting that once each year we should pause to review the path the student has traveled , and to reflect upon the perspective opening before him as an engineer . I was invited to come from Washington to take part in this ceremony and to say something to these young graduates . In searching for a theme ," it occurred to me. that perhaps my best contribution would be to duscuss certain beliefs as to college training , deal with the situation in which the young engineer finds himself on graduation , touch on the new ideas of the social and political responsibilities of the engineer , and point out what he may expect to find in practice , and , above all , what he must do to orient himself properly in the mining profession and maintain the best traditions of our brotherhood . Let us first review your college days and see what they have done for you . I am told there are still many temptations in college . I know there used to be . Rest assured the same holds true in the professional life ahead of you. The main difference is , perhaps , that your greatest temptations in college were those offered by your teachers , who tried to entice you into realms of harder work, closer application , increased concentration , clearer thinking and better understanding , by animating your curiosity and increasing your powers of reasoning and of observation . In other words , here you have carefully and systematically been decoyed toward finer and loftier things . Do not expect that similar helpful influences will greet you on every side in your professional life . Often quite the contrary is the case .

Oct 1, 1930

By E. R. Cole

One objective of Bureau of Mines recycling research is to devise technology that enables recovery of metals and minerals from wastes. From October 1982 through September 1985, researchers at the Bureau and at the University of Missouri Rolla (contract H0222002) investigated the use of nonferrous flue dust with varying Zn contents (11 to 66 pct) as a source of Zn for electrogalvanizing steel wire. The waste dusts used were from a secondary Cu smelter, a brass smelter, a Pb smelter, and a water treatment plant. The dusts were leached in H2S04, and the leach solutions were treated to make electrolyte for electrogalvanizing steel wire using soluble Zn anodes. Cyclic voltammetry was used in an inno-vative method to evaluate the quality of the electrolytes used for elec-rogalvanizing. After electrogalvanizing, the wire was drawn on a labo-ratory draw bench to simulate industrial practice. Corrosion resistance was measured by a number of electrochemical techniques and by the stan-dard ASTM salt-spray tests. After successful bench-scale tests, the process was demonstrated in an industrial pilot plant. Results indicate that nonferrous flue dusts can be used as a source of Zn for electro-galvanizing if certain impurities are either partially or completely removed from the starting electrolyte.

Jan 1, 1987

By James S. Grichar

Interest in mergers in the nonfuel mineral industry developed when 5 were listed among the 50 highest valued mergers in the United States in 1981. This report presents a Bureau of Mines study of trends in merger activity from 1960 to 1979 and explores motives for mergers in the nonfuel mining and mineral industry. The objective was to determine precedent for or a trend toward the 1981 acceleration in merger activity and to examine certain financial motives for non fuel mineral mergers. Data indicate that the relative value of non fuel mineral mergers has grown since 1972 although the number of mergers has remained proportionate to historical trends for all mergers. Since 1974, the assets acquired in "large," nonfuel mineral firm mergers, those of $10 million or more, have comprised at least 93 pct of assets acquired. More nonfuel mineral firm mergers involved mineral companies as the acquiring firm than vice versa but mining and minerals firms acquired were of higher value than nonmining firms. A major motivation for mergers involving large mineral firms was the acquisition of assets at less than replacement costs. Univariate statistical testing, a methodology chosen for its applicability to the data, confirms this hypothesis while rejecting other financial motives. The remainder of the work is devoted to a discussion of suggested areas for future study.

Jan 1, 1984

By E. Chin

Although Japan is a major producer of crude steel, it is poor in industrial raw materials. This Bureau of fines report describes Japan's raw material needs for chromium, cobalt, manganese, nickel, and tungsten to produce ferroalloys and alloy steels. Japanese imports of these ores or metals by quantity and source are given for 1972-81, inclusive, to indicate (1) the changes in the consumption and supply pattern, and (2) the degree of Japan's dependence on foreign sources. This report also describes measures implemented by Japan to reduce the risk- of supply interruption, and discusses the possible implications of supply shortages.

Jan 1, 1983

By John W. Sweeney

Shales and clays from Illinois were sampled, tested, and evaluated to determine feasibility of producing lightweight aggregate by rotary-kiln methods. Sampling procedures and the 1 ,,,y of the Pennsylvanian shale units are discussed. Chemical, X-ray spectrographic and X-ray petrographic analyses were run on the samples to determine if a correlation existed between chemical mineralogic composition and expansion. Preliminary expansion testing was conducted in a muffle furnace. Rotary-kiln tests were conducted in a 16- inch by 14-foot rotary kiln. The weight of the aggregate ranged from 27 to 59 pounds per cubic foot. Concrete cubes employing the aggregate were tested to determine the qualities of the concrete. Compressive strength of the concrete using the 7-bag of cement cement per cubic yard mix, after autoclave curing for 6 hours, ranged from 2,950 to 6,750 psi. No correlation was found between the chemical, X-ray spectrographic, and X-ray and petrographic analyses and expansion, Sixteen samples made suitable lightweight aggregates in the laboratory rotary kiln. The expansion temperature range of eight of the samples was extremely narrow, and difficulties would probably be encountered in processing these materials commercially.

Jan 1, 1965

By E. P. Youngman

In the Unfederated Malay States, with the exception of Johore, the rights of suzerainty, protection, and administration were transferred by giam to the British Government in 1909. In the States of Kelantan, Trengganu, Kedah, and Perlis, the rulers are assisted by State Councils and by British advisers appointed by the British Government.3 With respect to Johore, the largest, richest, and most highly organized of the Malay States not in the Federation, the treaty of December 11, 1885, with Great Britain, defined the relations of the State to the British Govern- ment and allowed the Maharaja to assume the title of "Sultan"; an amendment to this treaty (May 12, 1914) provided that the Sultan should be advised by a British officer, the General Adviser. ...... The political organization of the States is reflected in the mining legis- lation, Johore being the only one having a comprehensive code. The mining enactments now in force, according to the High Commissioner for the Malay States, are as follows:

Jun 1, 1932

By James S. Wroth

The Act of Congress approved June 25, 1926 (Public Act 424, 69th Congress), authorized joint investigations by the U. S. Geological Survey and the U. S. Bureau of Mines to determine "the location, extent, and mode of occurrence of potash deposits in the United States." The particular deposits selected for exploration were the extensive rock-salt formations underlying large areas in western Texas and southeastern New Mexico, from which potash salts had been identified in the cuttings and sludges from oil wells drilled with cable tools. The evidence of these sludge samples was qualitative only and beyond definitely proving the presence of potash salts in the salt beds, gave little clue to the possible size, richness, or extent of the potash occurrences.

Jan 1, 1929